Search Documents

By F. W. Bowdish

Analysis of data on the equilibrium exchange of sodium ions from salt solutions for calcium ions, from various fractions of an oxidized calcareous iron ore from Lorraine, France, strongly suggests that the calcium may be attached to the solid by only one of its bonds. Nearly equal values were found for the equilibrium expression from data covering concentration ranges of 1000 fold for the salt and 235 fold for the ion-exchangeable calcium. Differences indicated between the exchangeable calcium contents of the slime and the sandy portions of the ore, as well as the equilibrium relationship itself, are of importance in the flotation of the ore. During an experimental program on the flotation of oxidized calcareous iron ores from Lorraine, France, ion-exchangeable calcium was found in the ore. Because this source of calcium ions, if not controlled, could thwart all efforts at flotation, an extensive study was made of the phenomenon. The part of that study reported here was to obtain data on the equilibrium established between ore solids and solutions of sodium chloride, and to analyze the data to try to understand better the physical chemistry of the exchange. The ore contains oolites of goethite and quartz grains embedded in a matrix consisting of calcite and a brown cement believed to be the residue from oxidation of the silicate minerals found in fresh unoxidized ore. When ground, a substantial fraction of the ore becomes a fine slime in which is concentrated more than half of the alumina content of the ore. It is believed that the alumina occurs as unidentified clay minerals with which most of the ion-exchange capacity of the ore is associated. A preliminary experiment on the exchange of ions from the ore for sodium ions from solutions of NaCl showed that calcium was about ten times as abundant as magnesium in the exchange solutions. Thus calcium was the predominant ion in causing difficulties with flotation, and it was the only one for which data was obtained in this study. It is believed that the omission of magnesium ion exchange from consideration does not invalidate the results. It is possible, however, that inclusion of magnesium in the analyses and calculations or its prior elimination from the samples would have improved the consistency of the results. EXPERIMENTAL Data about the equilibrium exchange of sodium from solutions for calcium from the solids were obtained using two different samples of material. The solids

Jan 1, 1963

By James A. Barr, R. B. Burt, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 8 1/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority under the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By J. A. Barr, R. B. Burt, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 81/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority und'er the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 81/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority und'er the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By R. B. Burt, James A. Barr, I. S. Tillotson

DISCUSSION Howard Howie (Knoxville, Term.)—The authors are to be congratulated on the presentation of a paper containing so much valuable information on the pipeline transportation of phosphate, as there is very little literature on the subject. The writer is especially interested in the paper, as he conceived the arrangement of the Akin and Godwin plants and was in charge of the design work and the engineering incident to their construction. The Akin and other phosphate deposits in the Tennessee phosphate area lie on beds of limestone that are very irregular. The limestone beds, after the phosphate matrix has been removed, are similar in appearance to land severely eroded by the action of water and denuded of top soil. Depressions in the limestone, called cutters, are irregular in depth with vertical or overhanging walls, having the general appearance of cracks in dried clay. They change abruptly in direction, width, and depth, and vary on the Akin tract from 1 to 25 ft in depth and from 1 to 50 ft in width. Pinnacles of limestone commonly occur in the cutters which appear, when exposed, like small clifflike islands in a river. Limestone floats also occur. The phosphate matrix fills the cutters and covers the uncuttered areas, the thickness of the cover varying continually and sometimes rather abruptly. It occurs generally as stratifications of phosphate rock and clay of varying thickness. The phosphate rock in the matrix varies in hardness and in percents of silica, lime, iron oxides, and fluorine, and the clay varies in toughness. In some places the deposit consists of narrow strata of rock almost devoid of clay streaks. In other nearby locations the clay will predominate. When it is excavated, the phosphate rock breaks into thin irregular lumps, locally known as plate rock. Limestone lumps are also excavated with the matrix. Akin plate rock is generally much softer than that occurring in other deposits in the area. Because of the above described physical and chemical variations of the excavated material, the resultant slurry varies in size distribution, specific gravity, and percent of slimes. When the rock is soft or when there is an increase of clay, the slime fraction is greatly increased as it passes through pumps and pipelines, resulting in reduced pipe friction. It is obvious that the longer the pipeline the greater the reduction of coarse fractions into fines, causing a decrease in pipe friction that cannot be accurately evaluated. The matrix is mined with a dragline that drops it into a hopper with a grid composed of 9-in. parallel bar spacings located above the hammer mill. The matrix on, and passing through the grid, is subject to the action of powerful sprays which wash it down to the hammer mill, together with any limestone lumps that are not removed before passing through the grid. The hammer mill reduces the feed to lumps of plate rock and clay, most of which will pass through the 8-in. pump suction. The mixture discharges into a pool containing the pump suction pipe. Water from a hydraulic nozzle moves the mixture to the pump suction intake. The pump, driven by a variable speed motor, is the same size as the pumps mentioned on p. 279. Provision is made to remove any lumps that lodge in a bend in the suction pipe in a manner similar to that used in the Florida phosphate fields. The hammer mill and pump units are mounted on wide steel skids so that they can be moved as the mining operation progresses. The discharge from the pump flows through an abrasion-resistant spiral welded steel pipe 8 1/4 in. actual inside diam, 8 in. nominal diam, for a maximum distance of 2200 ft, which is the limiting pumping distance for one pump. This pipeline, referred to hereafter as pipeline A, discharges into a ball mill without balls, which in turn discharges into a rotary screen attached to it that separates the slurried matrix into 11/4-in. oversize and undersize fractions. The oversize is returned to the mill for further reduction; the undersize is pumped to a Dorrco washer and then flows into a hydroseparator 160 ft in diam. In spite of the size reduction in the hammer mill and the blunging and washing of the slurry in its passage through the pump, pipeline, mill, and washer, the discharge to the hydroseparator frequently contains mud balls almost perfectly spherical. Sometimes the discharge from the 16,000-ft pipeline at Godwin contains mud balls the size of bird shot and smaller. This pipeline will be referred to subsequently as line B. Liquid caustic is added to the slurry at the Akin plant before its passage through the hydro-separator, which decreases the size of particles in the overflow by dispersion. In passing through pumps 1, 2, and 3 and pipeline B, the slime fraction in the underflow is increased by abrasion and blunging and also by continuing dispersive action of the caustic. The matrix for use in the experimental tests referred to on p. 279 was obtained from three small surface openings on the Akin tract that were made previous to the purchase of the tract by the Authority. Matrix used in the 2 and 4-in. experimental pipeline tests was taken from the three openings and proportioned to obtain a sufficient quantity that would be fairly representative of the average in the Akin deposits. Prospecting samples of matrix had been obtained from drill holes which showed no small variation in physical and chemical properties. Some of the physical variation is evident from the size distribution of solids in samples taken during the tests covering line B flows so thoroughly made by the Authority under the direction of Mr. Burt, see Table V, p. 280. Hydraulic gradients for a pipe of 8-in. diam were derived from the 2 and 4-in. pipeline tests using the so-called representative matrix as above described, and plotted on the profile of pipeline B. Gradients of other materials in slurry form passing through pipelines that bore some similiarity to the Akin matrix slurry were also plotted. After a study had been made of the hydraulic gradients plotted on the profile and the varying slurry flow that would probably occur during actual operation, three pumps were ordered, referred to as No. 1, 2, and 3 on p. 279. No. 1 and 2 pumps were installed and the third kept in reserve should the operation of 1 and 2 pumps prove satisfactory, since installation of the third pump would require an attendant, as well as the laying of 5400 ft of pipe to supply it with seal-water from the Akin plant. Subsequently, it was found desirable to install the third pump to maintain capacity when the slime fraction was low and the coarse fractions were large. Reference to Fig. 6 will show that the flow in B line goes upgrade in three locations. At the outlet at Godwin, the slurry flows between two 45" bends for an approximate distance of 18 ft to rise above the ground a sufficient height to discharge into a launder feeding the first classifier. This condition requires extra energy, which is taken care of by keeping the hydraulic gradient a sufficient distance above the high points. Although there are rather heavy upgrades in the line, the choking condition that might occur at the

Jan 1, 1953

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By W. M. Weigel

WHILE electric lamps both of the cap and hand type are being introduced into many mines requiring the use of safety lamps, the oil-burning safety lamp is still used in the great majority of cases, and even where the former are used the latter must continue to be employed when testing for gas. It is not the intention to discuss here the relative merits of the two types, but simply to give a comparison of the illuminating effect or candlepower of several kinds of ordinary safety lamps used for general work and for testing. Few data have been published in recent years on this subject and because of this it is hoped that the following information may be of some interest and value. The lamps tested were in all cases. of standard size and in good condition, all practically new, and were selected from a collection of about 100 with a view to obtaining results on as many different common types as possible. With the exception of the gasoline-burning lamps, five different oils were used in each lamp to determine whether -particular oils were suited to particular lamps and whether there was any great difference in the illuminating power of the different oils, or whether some oils would maintain their illuminating power better than others throughout a working period of 8 hr. No attempt was made to determine the amount or cost of oil burned by each lamp, but the condition of the lamp, wick, glass, and gauzes was noted after each test.

Jan 8, 1916

Magazine Advertising $ 62,564 83 Magazine Sales 3,591 44 Total 66,156 27 Dues, Arrears 7,032 88 Dues, Current 96,839 74 Dues, New Members 6,525 00 Dues, in advance 1,907 02 Initiation Fees 7,584 00 Sale of Transactions 3,909 03 Sale of Binding .. 7,845 05 Sale of Special Editions 338 20 Sale of Year Book 76 20 Sale of Pamphlets 1,189 06 Sale of Authors' Reprints 867 54 Miscellaneous Receipts 62 93 Interest on Bank Balances 1,712 89 Interest on General Reserve Fund 337 50 Interest on Life Membership Fund 557 84 Interest on James Douglas Library Fund 5,491 89 Total Receipts $208,433 04

Jan 1, 1923

By A. F. Meger

REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal Co. who have helped develop, over a number of years, an efficient and flexible method for spraying con- trolled amounts of oil on coal. Since the George- town preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage.

Jan 7, 1954

By George Otis Smith

In the utilization of natural resources owner, operator, and consumer* should share the attendant benefits. Development needs to be planned under terms recognizing fully the interests of all concerned, for ally undue advantage given to any one of these participants is apt to involve even greater and disproportionate injury to one or both of the others. For this reason it is well to preface any consideration of needed reforms in legislation affecting the disposition of public land with a survey of certain fundamental principles that determine the general conditions of a11 land transfers preliminary to development, utilization, and production. The disposition of any undeveloped natural resource, whether timber, oil, coal, or water power, as a transaction to which land owner and prospective developer are parties, must be based in theory upon a division of expected returns.' Whatever the terms of such disposition, neither party can reasonably ask for anything other than an equitable division of the returns. Under this analysis three and only three questions need to be discussed; namely, what are those profits, how is this division to be accomplished, and what is the equitable basis of division ? The answer to the third question should probably be found by applying to the problem the principles of theoretical sociology, and the question need not be mentioned further at this time, inasmuch as it does not involve the practical considerations to be kept in mind in connection with the other questions, which are concerned with only the measure of returns and their division. That is to say, whether the land owner's equity is to be stated as 95 per cent, ox as 6 per cent, of the profits attending the development of the particular resource, no change would be necessary in the method to be adopted of arriving at the closest approximation of the prospective total profit. If on this basis we now compare the two methods of disposing of

Jan 1, 1915

By C. H. Burgess

ON June 5, 1947, Secretary of State George C. Marshall in a speech at Harvard University outlined a plan for the economic recovery of Europe. The plan contemplated that the United States should provide assistance which would enable the European nations better to help themselves and to help each other to reconstitute from their war-torn lands conditions which would make possible decent standards of living. The Foreign Assistance Act of 1948 was passed in April of that year, and established the Eco-

Jan 10, 1950

By J. B. Fisken

(Butte Meeting, August, 1913.) BEFORE touching upon the immediate subject of this paper a few facts of a historical nature as to the general application of electricity to mining might be of interest. As to what was actually the first application of electricity to mining, opinions will no doubt always differ. My experience does not go back far enough, nor are the records to which I have had access of any value as covering this point. Sydney F. Walker, a man whose pioneer experience in the application of electricity to mining purposes dates back as far as 1876, ,gave an interesting resume of the subject in an address before the South Wales branch of the Association of Mining Electrical Engineers at its 1.913 session, and, unless his statements are shown to be wrong, they should be accepted as facts. According to Mr. Walker, the ignition of charges of blasting powder was the first operation in mining to be accomplished with the aid of electricity. Very frequently this energy was furnished by a static machine and occasionally by a magneto generator. Later, this was followed by the application of electricity to bell signals, and we are told that this application was looked upon skeptically and regarded as an expensive experiment by the mining managers of those early days. At the Paris Exposition of 1878, there was exhibited an electric lamp, which suggested future possibilities to the mining engineers of those days. The first successful application of electric lighting to underground excavations that I have been able to find any record of is that of M. Blavier. In the year 1879' he installed two Serrin lamps and successfully illuminated one of the large underground chambers in the Angers slate quarries. Another early application of electricity to the lighting of mines is that in the large chambers in the salt mines of Maros-Ujvár, in Hungary; these have been regularly and successfully lighted elec-

Jan 6, 1913

By M. Albertson

AT Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin' Was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 in.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 in.), the width at the lower lobe was about. 1000 ft., and the, width at the narrows probably. 400 to 500 ft. The original depth of water varied from 20, to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft.. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the. lake. About

Jan 2, 1921

By Klaus W. John

The geologic factor of greatest significance in rock mechanics and rock engineering is considered to be the geologic structure represented by joints, faults, and other planes of weakness. This geologic structure differentiates between the rock element and the rock system composed of these elements. Only during the last decade has the difference of the technological properties of element and system been recognized but this appears to be more in theory than in engineering practice. If rock mechanics is to achieve real significance in engineering practice, it has to provide methods of analysis which are realistic compromises between the best representation of the actual conditions and pragmatic engineering. The rock mechanics practitioner has to face the fact that many geological engineering and rock mechanics problems may be too complex to allow rigorous analysis but at the same time are deemed satisfactory for the construction of major structures. Ultimately, the geotechnical engineer or the engineering geologist has to express the effect of geologic factors in quantitative, even if approximate, terms and provide numerical data on strength and deformability of rock systems to be utilized in construction. Qualitative evaluations, quantitative descriptions of geologic features as such, and comparisons of specific test results are always of interest but may not suffice as basis for engineering decisions and designs. The present efforts of the rock mechanics group at the Karlsruhe University, Federal Republic of Germany, are based on a systematic combination of geomechanical models and numerical analyses based on the finite element approach. This group considers that at the present stage

Jan 1, 1970

By Charles Catlett

My attention having been called several years ago to the possibility of increasing the yield of coke per ton of coal, as obtained in certain bee-hive ovens, I called the attention of the Institute to the matter at the New York meeting in 1899. I have had occasion since to witness the indifference with which this matter is ordinarily considered, and, on the other hand, the marked improvement which comes from even a most perfunctory effort in that direction; and I am almost tempted to say that nothing in connection with the coking of coal is at present so important. There are other factors, which are fundamental and necessary; but they have been considered already ; while the question of yield is, as a rule, absolutely ignored, or some figure is taken as the result of a special burning of one or two ovens, and the assumption is made that the whole battery is yielding at that rate. The uncertainty of this assumption I may illustrate by saying that, in my own observation, the burning of a single oven in a battery frequently gives, by actual weight, as much as 69 or 70 per cent. of merchantable coke, while the battery as a whole was yielding only an average of 63 per cent. Only from careful records, checked at least once a month, of the weight of the coal going to the ovens and the weight of coke produced, can any correct idea of the actual yield be gained, or methods be modified so as to produce good results; yet, as a rule, the crudest estimates are usually the only available data. In many cases there are reasons for this loose practice. The coal is mined by measurement; the payment for drawing the ovens is in proportion to the amount of cod which goes to them; and, not uncommonly, the royalty is so much a ton of coke, not of coal. The mine-manager is tempted to increase the volume of coal mined which is paid for as a ton, and to do the same thing in charging the ovens. Nor does he

Jan 1, 1903

By M. L. Jeremic

Mining practice and underground studies show that, besides mining stresses, lateral tectonic stress also influences roadway stability. Roadways perpendicular to the direction of major lateral stress experience the majority of roof falls, accelerated floor heave, and extrusion of coal ribs into openings. They have the most severe deformations and their maintenance is difficult. Roadways parallel to the major lateral stress exhibit roof sagging and bed separation, moderate though sometimes uneven floor heave, and slabbing of coal ribs into openings. Roadways oblique to lateral stress have, to a certain degree, self-supporting roofs, uniform floor heave, and limited sloughing of coal ribs into openings. The optimal orientation of roadways is, therefore, oblique to the lateral stress direction with fewer crosscuts between them.

Jan 1, 1982

By Kenneth N. Weaver

Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War II, however, the industry began to recognize the need for geological exploration, and some of the larger companies began to build a permanent geological staff. This development had its roots in the following factors: Rapid expansion of the industry; closing of many cement plants due to inadequate raw materials; necessity for upgrading the quality of portland cement; and the increasingly large capital investment required to build new cement plants, which in turn, required a higher degree of accuracy in reserve calculations. Whereas the geologist's function during the active expansion of capacity was primarily in exploration, one of his major functions today is the development of existing reserves.

Jan 1, 1965

By M. T. Melvin, N. P. Kripakov

The practical application of a post-processing modeling procedure to simulate progressive rock failure around the periphery of coal mine entries is presented. This numerical scheme utilizes a simple rock model that incorporates easily obtainable input parameters consistent with basic rock mechanics principles. These parameters include the cohesion, angle of internal friction, modulus of elasticity, and Poisson's ratio of the bedded deposits that comprise the imediate roof, coal seam, and immediate floor. The geometry of the entry, along with the in situ stresses existing at a mine site prior to mining, are also considered in the analysis. The potential of this procedure as a predictive tool in determining the extent of pillar rib fracturing and yielding of the immediate roof and floor is evaluated assuming a Mohr- Coulomb failure criterion. The procedure is designed to be user oriented and is adaptable to any finite element code with linear elastic capability, making it particularly attractive to users with limited budgets and computer size.

Jan 1, 1983

By A. D. Rovig, T. J. Fisher

By converting its autogenous mills to steel ball mills at the C. E. Weed concentrator in Butte, Mont., The Anaconda Co. has achieved substantial increases in through- put tonnage, plus better recoveries as a result of the finer feed size to subsequent flotation operations. If steel grinding is so superior to autogenous grinding, why wasn't it chosen in the first place? Briefly, here's why:

Jan 10, 1975

HAVING shown you before how moulds of statues and also those of guns are constructed, I wish to tell you at present how, if you wish to cast them in bronze, you are further to prepare and arrange these moulds so that they may receive the melted mass of the metals in a friendly manner and without disturbance. I know that you understand that a real and intense heat has been intro-

Jan 1, 1942