Search Documents

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

By G. C. Stone

At the conclusion of my paper on the same subject read at the Boston meeting of the Institute, I offered to send some of sample No. 2 to any chemist who wished to analyze it. Eight chemists wrote to me for samples; so far I have received results from five. I give these results in a table (on the following page), together with the results previously obtained: As to the chemists and their methods : K is an iron-works chemist whom I only know by correspondence; lie writes: "No. 27(13.64) was obtained by the method I generally use, as follows : Dissolve 0.8 grams spiegel in hydrochloric acid and a little potassium chlorate, in a half-liter flask. Boil off most of the acid, add ammonia in slight excess, redissolve in acetic acid, using rather more than is really necessary, and then add 8 or 10 grams of sodium acetate and make up to the mark with warm water. Boil hard for fifteen minutes, then allow to settle (cool?), until the liquid reaches the mark, and withdraw 300 C.C. of the nearly clear liquid. Add to this an excess of hydrochloric acid, evaporate to dryness, take up with hydrochloric acid and water, and separate the iron by two precipitations with ammonia (I have often tested the ferric hydrate for manganese, but have never found any, if the separation by ammonia was properly made). Finally, precipitate the manganese as phosphate." Nos. 28, 29 (13.35, 13.07) were by Ford's method." No. 30 (13.50) was by Troilus's method He writes, " I may add the results are quite as good as I expected, although for any element except manganese, they are not close enough for anything like accurate work." L is a firm of commercial chemists of large experience who have made a specialty of iron work. Their method is as follows : Dissolve

Jan 1, 1884

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By A. Aly Selim, Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the U.S. Bureau of Mines Twin Cities Mining Research Center. The simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting, is described in this paper. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of systems with a number of stopes or faces. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence, total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1976

By R. F. Marande, R. S. Busk

THE magnesium-aluminum-zinc system contains most of the magnesium-base alloys used commercially, although in practice the ternary, alloys are usually modified by the addition of a small amount [ ] of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the object of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.1 [ ] All alloys reported were made in 15-lb. melts, superheated to 1700°F. for 15 min., cooled to 1400°F. and poured in sand molds. The test bars produced had a ½ in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. CONSTITUTIONAL DATA Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

By J. T. Michalak, H. W. Paxton

The recovery of the initial flow stress of poly-crystalline iron is characterized by a) a logarithmic time dependence; b) an increasing activation energy with increasing recovery; c) an increased ?,ate and fraction of recovery with decreased temperature of deformation; and d) an increased rate with increased deformation. Isochro)ml studies of the recovery of single crystals revealed more sluggish recovery. The original flou3 stress of single crystals could be regained by recovery anneals at 800"or 900°C. ThE great majority of the theoretical treatments and experimental studies of strain-hardening have been concerned with the close-packed lattices.' Very little effort has been expended on the bcc structure so that the theory of work-hardening of this lattice is essentially nonexistent. The limited amount of experimental data resulting from the direct studies on silicon-iron,2 low-carbon steel,3 and purified irons4"7 does not as yet permit a detailed analysis of the strain-hardening. Studies concerned with the effects of annealing following deformation have been few in number," have been somewhat limited in extent, and have had the disadvantage of using irons containing a substantial impurity content. The present research was undertaken to augment the limited knowledge we have of the characteristics of a bcc metal as regards strain-hardening and recovery from the strain-hardened state. The recovery of the flow stress has been employed since it was felt that the stress associated with the hardened state gives at least a fair qualitative description of the state of the imperfections causing the hardening. The study was concerned primarily with the recovery of flow stress following strain-hardening of polycrys-talline, zone-melted iron as a function of the amount of deformation, the temperature of deformation, and the time and temperature of the recovery anneal. A limited investigation of the recovery of the initial flow stress of single crystals of this same material as a function of the recovery temperature was also conducted in conjunction with the Lambot X-ray technique." MATERIAL The zone-melted iron used in this investigation was obtained through the courtesy of the American Iron and Steel Institute and Battelle Memorial Institute. The analysis, as given by the supplier indicated a maximum impurity content of 0.02 wt pct excluding those impurities listed in Table I. (The actual impurity content is very probably less than this since detection limits were considered as the amount of a particular impurity level.) Also listed in Table I are the interstitial impurity contents of the iron at various stages of experimental work indicating that these im-

Jan 1, 1962

By C. H. Mathewson, E. M. Thalheimer

In planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100' C. to 1,000" C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,' in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper. The great importance of copper both as a material of construction and as the base of our most important alloys (aside from steel) has led to innumerable investigations of its properties, particularly in commercial forms. Naturally, the merits of furnace-refined lake coppers us. those of the very pure electrolytic product have furnished the subject of much experimental work and animated discussion, wherein the effect of arsenic has by no means been overlooked. In the literature of the past 10 years,

Jan 1, 1917

By Robert W. Metcalf

THE name "tripoli" is used to designate a number of more or less similar types of silica of sedimentary origin. Usually they are spoken of as "soft" silicas, and are light, very fine grained, porous, and friable. Structure is microcrystalline or cryptocrystalline. The deposits are the residual product of weathering and occur in massive form, either blocky or in friable masses. Tripoli is the end product of the weathering of siliceous Limestones, cherty limestones, or cherts. Weathering removes the calcium carbon- ate, leaving a finely divided siliceous residue to which the name "tripoli" has been applied. Authorities differ as to whether the chert accumulates first and is converted into tripoli or the tripoli is derived by direct decay from various forms of silica during initial weathering of the Limestone. It has also been asserted that tripolis were formed in situ in essentially their present condition as a flocculent, colloidal silica, but it is now believed by most geologists that varying degrees of pressure, combined with one or more methods of origin, have influenced the characteristics of the deposits. Considerable confusion has existed as to what constitutes tripoli. Owing to the similarity of names, tripolite, a type of diatomaceous earth found originally in Tripoli in northern Africa, has been erroneously called tripoli. Tripoli, however, contains no diatoms, the distinguishing characteristic of diatomaceous earth. The material mined in the Missouri-Oklahoma area has been considered by the trade to be the type material, and many feel that the term "tripoli" should more properly be restricted to the product of this region. Although also designated as soft silica, it would be less misleading, perhaps, if the siliceous material mined in southern Illinois were called amorphous silica. Both the Missouri-Oklahoma and Illinois materials are very high in silica. Different in composition, as it is very much lower in silica content than tripoli or amorphous silica, yet included under the classification of tripoli in Bureau of Mines statistical data, is the small but important output of rottenstone in Lycoming County, Pennsylvania. The principal justification for grouping these three types of silica is similarity of use.

Jan 1, 1949

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that' the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932

By Clarence G. Merritt

Stainless iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mlysterious electrolytic effects or comparatively minute non metallic inclusions. Many uses for a steel with such excellent physical properties as are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties,1-2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties—hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C;, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion. Monypenny reports that a loss of hardness is

Jan 1, 1932

[A AALSETH Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Mont ABADIE Henry G (M 43) Asst to. Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif. ABBET Waldo (A 56) Asst Diet Oper Supt Sun Oil Co P 0 Box 66, Stowelt, Tex ABBOTT Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT Fred E Jr (M 59) Abqaiq Diet Mgr Arabian American Oil Co Dhahran, Saudi Arabia ABBOTT J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT Richard H (J 51) Partner Abbott & Howard 422 W Hermosa, San Antonio 12, Tex ABBOTT William G (M 50) Div Mgr Rice Engrg &. Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carml, 111]

Jan 1, 1961

By George M. Fowler, R. E. Illidge

Part I. Developing BY GEORGE M. FOWL INTRODUCTION The Tri-State district comprises an area of about 2000 square miles in southwestern Missouri, southeastern Kansas, and north [ ] eastern Oklahoma. The part that is in and contiguous to Missouri is still sometimes designated as the Joplin district (Fig. I). EARLY OPERATIONS Mining operations in what is now the Tri-State district date from about 1848 and have been continuous to the present. Apparently the first discoveries of ore were made about the same time near the present sites of Joplin, Oronogo, and Granby. Lead minerals were found at grass roots, probably in shattered rock in shallow excavations, then these minerals were followed in shear zones to deeper horizons. The mining of zinc followed. Before 1874, zinc ore was worthless and discarded as waste. According to published records, the total production of lead to that date was 49,000 tons of metal from 70,000 tons of concentrates. PRODUCTION The aggregate ore production from the Tri-State district was recorded at interval

Jan 1, 1943

By I. Nilsson, G. Sundkvist, A. Danielsson

A spectrochemical method of slag analysis is descibed which utilizes fusion of the sample with a flux, then cooling and crushing to put all samples into a common form. The powder, is then fed onto adhesive tape and passed through a spark by means of a special device to provide very reproducible discharge conditions. Combined with a direct-reading optical emission instrument, this system provides speed and accuracy of antilysis heretofore unobtainable for. slag samples by any other method. THERE are many suggested methods for spectro-chemical analysis of slags. The most important are fusion-pellet methods and solution methods. In our company the fusion-pellet method has been used earlier, and is described by Lounamaa. W. H. Tingle and C. K. Matocha have made refinements of the pellet method.' A Committee of the British Iron and Steel Research Association has investigated different methods of spectrochemical analysis of slags. Its purpose was to formulate a method which would give the complete analysis in 30 min with an accuracy of ±3 pct. The committee recommends a solution technique, which was thought to correspond best to their requirements. The method to be described is a fusion-tape method. The sample is isoformed by fusion and grinding. The powder is analyzed with the tape technique. The tape machine and some of its applications are described earlier.4'5 The powder to be analyzed is continuously fed onto a moving adhesive tape, which passes through the spark gap. The sparks break through the tape and vaporize and excite the material to be analyzed. The most outstanding feature of the tape machine is its very high reproducibility. The concept of isoformation has been introduced earlier.= It means a pretreatment of the samples to make them uniform from the spectralanalytical point of view, i.e., cancelling systematic differences between the samples. The purpose of the isoformation is to reduce the influence of particle size, as well as chemical and mineral composition. Before describing the isoformation by fusion plus grinding, which is the purpose of this paper, a few words will be said about two other types of isoformations, i.e., grinding with buffer and ion exchange plus grinding as they have been considered during the application of the tape technique for slag analysis. Grinding with buffer might be a sufficient isoformation in some special cases, where the mineral composition is defined. The time of grinding must, however, be rather long, at least 5 to 10 min, even when using such an efficient mill as the Swing Mill from Messrs. Siebtechnik, Mühlheim, Germany. This type of isoformation is not recommended due to its limitations and due to the fact that the gain in time compared with the fusion technique is almost negligible. The principle of ion exchange plus grinding and some of its applications have been described.5 The following elements of interest in slag analysis can be determined in this way: Na, K, Cu, Mg, Ca, Ba, Zn, Pb, Al, Cr, Mn, Fe, Co, Ni. The very important element Si, however, cannot be analyzed with this method. Although the ion exchange isoformation for slag analysis cannot be looked upon as a routine method, it can be used for

Jan 1, 1962

By M. A. Goudie

The deposits occur in a large salt basin of Middle Devonian age. The potash, the final deposit in the salt basin, results from several interrupted cycles of evaporation and dessication. The deposits are extensive, and, at first glance, relatively undisturbed. With more and more wells being drilled, it has now become evident that salt solution has played a large part in changing the original deposits, resulting in some cases in partial to complete removal of the potash and the underlying halite. The most dominant factor in the removal of salt by solution appears to have been tectonic movement and consequent faulting, probably of relatively minor dimensions but of major importance. Evidence which indicates the tilting of the evaporite basin to the north and northwest is shown by the changing pattern of the basin during succeeding eras of potash deposition. The potash minerals of most importance economically are sylvite and carnallite. Reserve calculations indicate that 6.4 billion tons of recoverable high grade potash in K2O equivalent exist in the basin. The Devonian salt basin, which contains the Saskatchewan potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota (Fig. 1). The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 285 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis, and Prairie Evaporite Formations. The Ashern formation, with an average thickness of 30 ft, sometimes called the Third Red Bed, consists of dolomitic shales and shaly dolomites. The Winnipegosis, is a reef-type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The thickness varies from 50 to 250 ft. The Prairie Evaporite formation, varying from 0 to 600 ft in thickness, consists of halite with interbedded anhydrite and shale, with considerable amounts of potassium salts in the upper part of the formation. The potassium salts are chiefly chlorides, although very minor occurrences of sulfates have been re- ported. The anhydrite beds do not appear to be continuous, although generally one or two bands of anhydrite underlie the lowest potash zone and are used as marker horizons. The shale occurs as seams interbedded with the salts, as large irregular inclusions in the salts and as very fine particles in intimate mixture with the salts. The Prairie Evaporite Formation is overlain by the Second Red Bed member, the Dawson Bay Formation and the First Red Bed Member of the Manitoba Group, listed in ascending order. The Red Beds are shales which vary in color from red to green, maroon, grey, grey-black, and reddish purples. They serve as marker horizons for coring the potash. The Second Red Bed averages 14 ft in thickness, the First Red Bed 35 ft. The Dawson Bay Formation, which everywhere overlies the First Red Bed and the Prairie Evaporite Formation in the area under discussion, is a reef type of carbonate, in some places limestone, in others limestone and dolomite, with vugular to pinpoint porosity averaging 130 ft in thickness. In some parts of the area, it has a salt section near the top of the formation, usually with interbedded shales and limestones. In other parts of the area, it is waterbearing and the salt is absent. Detailed mapping has indicated that the areas in which the Dawson Bay is water-bearing are areas which have been disturbed by faulting. Where the Dawson Bay is salt-bearing, the porosity has been plugged by salt. The total thickness of the salt varies from between 600 to 700 ft in the center of the basin to zero at the northern edge of the basin (Fig. 2).* The salt-free area in the center of the Province is believed to have resulted from removal of salt by solution. Evidence from several wells suggests that salt removal has been a continuing process from the time of deposition to the present day. One well drilled between the Quill Lakes for potash information encountered

Jan 1, 1961

By A. C. Lane

Relations de la profondeur de plissement avec la gravita-tion et la hauteur des montagnes dans les Alpes. Par A. Heim (Zurich) 50me Anniversaire, Livre Jubilaire Soc. Geol. De Belgique, Rome, Fascicule 1, 17 to 28. Measurements show a negative anomaly, less densities of .the material below sea level. The author expresses it in terms of the thickness of rocks of an arbitrary density, 2.4, which might be considered wanting. The accordant heights of the summits, the depths of the folds, the deficiency in .gravity, and denudation he finds to be connected. The Alps float on the lightness of the folds of "sal" of weight 2.6 to 2.75 plunged into the heavier "Sima" according to a for-mula: P = h (2.7/2.8-2.7) where - P is the depth of fold-ing below sea level; 2.7 is the weight of the material accu-mulated in folding; 2.8 is the weight of the material dis-placed by it; and h is the mean height of the mountainous regions. For instance, between the valley of Saar and the Val de Bagne in Valais the depth of the folds according to Ar-gand's profiles is between 30 and 40 kilometers. The loss of gravity has been estimated in this region as 1450 X 2.4 = 3480 in units of weight. Obviously errors in the densities would profoundly affect the estimates of the thickness of folding, but his depths of folds are obtained from sections, and from them he works back to the densities. Of course other densities might be placed in the formula. Zur Dichte bestimmung von Tonen. By J. Koenigsberger, Berg u. Hüttenmannisches Jahrbuch, 75, I. Discusses Dr. B. Wilser's investigations as to the best way of obtaining the weight of rocks per unit volume. The use of mercury for rocks affected by water as there recom-mended may easily give too large volumes unless 1 to 3 atm. pressure is used. Thick machine oil is recommended for large lumps of clay.

Jan 4, 1928

By Stuart M. Buck, J. H. Bramwell, Edward H. Williams

The Southwest Virginia Improvement Company began operations in the Bluestone Flat-Top coal-field, situated in Tazewell County, Virginia, in the fall of 1881. In May, 1883, the company had built 200 coke-ovens, and by March, 188-1, had 9000 feet of entries, exclusive of air-ways, in the Nelson or Rig coal-bed of this district (which here averages eleven feet in thickness), and had extracted 200,000 tons of coal, representing an area of about twenty acres. About this opening has grown the recently incorporated city of Pocahontas, and the completion of the New River branch of the Norfolk and Western Railroad to this point enabled the company to make large contracts for supplying coal and coke, so that it was deemed necessary, on account of the limited area developed, to work the mine day and night to fill orders. At 1.30 Thursday morning, March 13th, the inhabitants of Pocahontas were awakened by a violent shock, and within a few minutes all knew that the East mine had been the scene of an explosion of so general a nature that, of the 114 men at work, not one had escaped. The daily papers gave more or less distorted accounts of the number of victims, the scenes in and about, the mine, and the probable cause of the disaster. At the request of the company, the President of the American Institute of Mining Engineers appointed the undersigned a committee of three to investigate the matter, and the committee thus constituted presents the following report, accompanied by a copy of the testimony taken daring the investigation, for preservation in the archives of the Institute. Pocahontas was reached on Thursday, April 24th, and left on Friday, May 2d. During this interval the committee made repeated visits to the mine, especially to the points, of most importance, examining it carefully in every part; and summoned a number of witnesses, twenty-six of whom appeared and testified. The mine had been left in the same state as when the bodies were

Jan 1, 1885

By B. C. Burgess

AFTER many years of close and friendly association with talc and soap-stone, this orthographically distinguished mineral steps forth in this edition, for the first time in a chapter of its own. Pyr, the Greek for fire, and phyllite, a rock or stone, form its name and at the same time refer to the first recorded use of pyrophyllite as firestones or hearthstones. Another derivation of "phyllite" is from the Greek phyllites, "of leaves," alluding to the beautiful white radial crystal aggregates that form when pyrophyllite is heated. Pyrophyllite used by the Chinese for carving is called agalmatolite, from the Greek agolma, meaning an image. COMPOSITION AND PROPERTIES Pyrophyllite has previously been grouped with talc because of the close similarity of the minerals in physical and optical properties. They have the same space group; and chemically they are closely related, pyrophyllite being the aluminum silicate A12Si4010(OH)2 and talc the magnesium silicate Mg3Si4010 (OH) 2. Another arrangement of the pyrophyllite formula is generally given as A12034Si02H20 because it expresses the chemical composition as usually determined (alumina 28.3 pct, silica 66.7 pct, water 5.0 pct). Vanderbilt gives pH values of pyrophyllite 5.6 to 8.4.29 Pyrophyllite usually is white, pale green, cream or pale yellow, buff or light gray. It is found in darker shades and other colors principally due to oxidation of contained iron minerals. It is translucent in thin sections. In hardness it is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. In bulk specific gravity, the powdered mineral ranges from 0.4 to 0.7. Its luster is pearly to dull; it is infusible in the Bunsen burner flame, slightly affected by aqueous solutions of sodium carbonate and hydrochloric acid. It is decomposed by sulphuric acid, with separation of gelatinous silica. It is characterized chiefly by its micaceous structure and cleavage, its softness and greasy feel. Two other varieties occur

Jan 1, 1949

By J. P. Van Kleunen

9.3-1. Introduction. The demands of industry for handling materials at higher rates and at reduced costs have had a very significant effect on belt conveyor technology. Although the general appearance of the belt conveyor today is essentially the same as it has been for the past several decades, the similarity ends there. Each component comprising the conveyor system has been continuously improved through design and materials technology to enable present conveyor systems to operate at ever-increasing rates and reliability. For example, twenty years ago the strongest commercially available, fabric-reinforced conveyor belting had a tension rating of 50 lb per ply-in. Currently, fabric-reinforced belts are available with ratings of 350 lb per ply-in. and steel cable reinforced belting is available with tension ratings of 3000 lb per in. of belt width (3). These technological advances have therefore enabled the belt conveyor to not only attain acceptance as a preferred method for in-plant movement of bulk materials, but also to be used for long distance transportation of bulk materials, particularly in areas of adverse terrain. The information contained in this chapter is intended to assist the reader to make basic decisions regarding the use and application of a conveyor system. The design of an overland conveyor transportation system or an in-plant process conveyor is accordingly beyond the scope of this article. Many comprehensive technical works covering the design of a belt conveyor are currently available from the manufacturers of materials handling equipment (6, 7, 9, 11). The design handbook published by the Conveyor Equipment Manufacturers Association is particularly recommended (2). 9.3-2. Conveyor Capacities. One of the most important factors in determining the proper size of a conveyor system is the rate at which material must be handled. Although tables and charts are available to the conveyor designer to assist him in his selection of conveyor components, only the

Jan 1, 1968