Search Documents

By G. F. Bolling

Single crystals of each metal were deformed at 77°K and heated at constant rates, variously in the range 0.125" to 4o°Kper min from 77" to -390oK, while being monitored in an X-ray diffractometer. Changes in diffraction-peak heights and line breadths were used to ascertain the temperature ranges of recrystalliza-tion. The results were subjected to the analysis of nicholas' in order to obtain the rate-controlling activation energies,Q. In this analysis no recourse to a separate and distinct nucleation stage is required and the results of studying recrystallization proved consistent with the hypothesis of a constant number of nuclei or equivalent hypotheses. The values Pb = 5.5 ± 0.5 keal per mole Zn ~ 7.5 Sn - 5 Bi - 9. 5 correspond for lead, zinc, and tin to activation energies obtained elsewhere for grain boundary migration, and for bismuth and lead to previous studies of re-crystallization by Barrett.6 This correlation allows the conclusions that interference from recovery was minimal and that the observed recrystallization rates in these pure metals are effectively governed by grain boundary migration. Good agreement was not found between the results of this kind of study in zone-refined aluminum and previous work; and supplementary isothermral experiments involving hardness tests and metallography did not resolve the discrepancy. Nevertheless, at least a range,Q = 11.5 ± 2 keal per mole, can be assigned to the activation energy for boundary migration in aluminum. An experimental study of one aspect of the recrystallization process is presented here for four metals of different crystal structure. The metals chosen for study were all zone-refined to reduce impurity effects, but the attendant high purity presented a difficulty. For any reasonably high driving force a "re-crystallization temperature", TR, is in the range of 0.25 T,, where T, is the absolute melting point, and study was therefore restricted to lower temperatures. An X-ray technique under constant heating-rate conditions adequate above 90°K was devised for the study; in consequence, a newer type of analysis following Nicholas1 had to be used to obtain quantitative information about activation energies. The standard methods of studying recrystallization have involved the comparable analyses of Johnson and Mehl2 and Avrami3 which are reviewed by Burke and Turnbull.* The general analysis4 which is applied only to isothermal studies using any of various investigative techniques states:

Jan 1, 1968

By T. O. King, Y. P. Gupta

The self-diffusion of sodium in two sodium silicate liquids was measured in the temperature range 850" to 1500°C by the capillary-reservoir technique. Radioactive Na 22 was used as the tracer. The total count and autoradiographic methods were used for determination of the total Na 22 depletion and diffusion profiles of the dqy-used specimens. The diffusion coefficients obtained by the autoradiographic technique are slightly smaller than those obtained by a total count method. Error analysis of the two methods suggests that more confidence be placed in the results of the total count method. The experimental results were analyzed in terms of the existing activated rate process theory. The activation energy for diffusion was shown to decrease markedly as the temperature increased. This was attributed to a variation in the heat of activation with temperature, probably related to a change in the distribution of anions associated wilh the cation. In terms of a model, suggested for diffusion in liquid silicates, differences in the aclivation energies for diffusion and electrical conduction may arise from the effect of the electric field applied in conduction measurements. It is generally accepted that liquid silicates consist of cations and an equilibrium distribution of complex anions determined by temperature and composition. Transport properties in molten silicates are of interest, not merely because of their relevance to the kinetics of pyrometallurgical reactions and glassmak-ing processes, but also because they are useful to development of the theory of such ionic liquids. Self-diffusion is one such transport process that may, if studied for liquid silicates of widely varying compositions, indicate structural changes through changes in the activation energy for diffusion. The self-diffusion of calcium, silicon,' sulfur: aluminum, 4 and oxygenS in lime-alumina-silica melts and of iron6 in molten iron silicates have been measured. Unfortunately, the errors in some of the reported activation energies for diffusion are too large to allow firm conclusions concerning structure and the mechanism of the diffusion process to be drawn. The research reported here was a study of the self-diffusion of sodium in liquid sodium silicates. The soda-silica system was chosen since: i) a reasonable composition range can be covered in the binary system at moderate temperatures; ii) suitable isotopes of sodium (radioactive Na 22 and NaZ4) can be obtained; iii) data on the electrical conductivity and viscosity of sodium silicate liquids are available. However, the range of composition actually used in diffusion experiments was limited, to 20 to 35 wt pct soda, by the relatively high viscosity of silica-rich compositions and by evaporation of soda from basic melts. EXPERIMENTAL PROCEDURE The capillary-reservoir technique was used, wherein a radioactive tracer, Na 22, incorporated in the capillary melt, was allowed to diffuse out of the platinum capillary tube into a large reservoir of silicate liquid containing a chemically identical melt, but without radioactive tracer. After a specific diffusion time, both the total depletion in the tracer concentration and concentration-distance profiles of the diffused samples were measured by procedures to be described later. The diffusion cell assembly was similar to that used by Koros and King.' The temperature of the diffusion cell was measured with a calibrated Pt, Pt-10 pct Rh thermocouple located at the center of the liquid reservoir. The same thermocouple was used to obtain the temperature profile in the reservoir. The temperature at the top of the reservoir was slightly higher (2°C) than that at the bottom, to minimize convection in the capillary tubes, which were placed, open end up, in the reservoir. Convection was not expected to be a problem since the length-to-diameter ratio of the tubes was about 12:1 and the maximum capillary diameter was 1 mm. The diffusion cell was heated in a molybdenum-wire resistance furnace, previously used by Koros and King, but somewhat modified. A Pt, Pt-10 pct Rh thermocouple enclosed in an alumina tube and located near the furnace winding was used in conjunction with a preamplifier and Micromax proportional controller for temperature control, within 4°C, at temperatures near 1500°C. Before starting a diffusion run, the furnace was heated to the desired temperature and an alumina guide assembly for the capillaries was slowly lowered to within 2 cm of the liquid reservoir. The capillaries were thus heated to about the temperature of the bath. The run was started by lowering the assembly till the open ends of the capillaries were about 1 cm below the surface of the liquid. The run was ended by raising the assembly to about 15 cm above the liquid bath. Later, the sample assembly was slowly withdrawn from the furnace. Six diffusion samples were usually run at the same time. Three runs made with the open ends of the capillaries down were discarded because in the majority of these samples air bubbles trapped at the open end were observed. Some glass adhered to the outside of the capillary on withdrawal. This was carefully removed and used to check that the Na 22 activity in the sink remained at a low level. Materials. Nonradioactive sodium silicates were prepared by melting, in a platinum crucible, weighed quantities of sodium carbonate and powdered silica. To prepare radioactive sodium silicates, Na2 obtained in HC1 solution, was first checked for radioactive impurities by obtaining a y-ray energy spectrum, then the chloride ions were removed by anion-ex-

Jan 1, 1968

By J. Chipman, M. N. Dastur

The importance of dissolved oxygen as a principal reagent in the refining of liquid steel and the necessity for its removal in the finishing of many grades have stimulated numerous studies of its chemical behavior in the steel bath. From the thermodynaniic viewpoint the essential data are those which determine the free energy of oxygen in solution as a function of temperature and composition of the molten metal. A number of experimental studies have been reported in recent years from which the free energy of oxygen in iron-oxygen melts can be obtained with a fair degree of accuracy for temperatures not too far from the melting point. Certain discrepancies remain, however, which imply considerable uncertainty at higher temperatures; also several sources of error were recognized in the earlier studies. It has been the object of the experimental work reported in this paper to reexamine these sources of uncertainty and to redetermine the equilibrium condition in the reaction of hydrogen with oxygen dissolved in liquid iron. The reaction and its equilibrium constant are: H2 (g) + Q = H2O (g); K1 _ PH2O / [1] Ph2 X % O Here the underlined symbol Q designates oxygen dissolved in liquid iron. The activity of this dissolved oxygen is known to be directly proportional to its concentrationl,2 and is taken as equal to its weight percent. The closely related reaction of dissolved oxygen with carbon monoxide has also been investigated:3,4,5 co (g) +O = CO?(g); K _ Pco2___ [2] K2= pco X % O [2] The two reactions are related through the wat,er-gas equilibriuni: H2 (g) + CO2 (g) = CO (g) + H2O (g); K2 = PCO X PH2O [3] PH2 X PCO2 and with the aid of the accurately known equilibrium constant of this reaction, it has been shown5 that the experimental data on reactions [1] and 121 are in fairly good, though not exact, agreement. Experimental Method Great care was taken to avoid the principal sources of error of previous studies, namely, gaseous thermal diffusion and temperature measurement. The apparatus was designed to provide controlled preheating of the inlet gases and to permit the addition of an inert gas (argon) in controlled amounts, two measures found to be essential for elimination of thermal diffusion. A known mixture of water vapor and hydrogen was obtained by saturating purified hydrogen with water vapor at controlled temperature. This mixture, with the addition of purified argon, was passed over the surface of a small melt (approximately 70 g) of electrolytic iron in a closed induction furnace. After sufficient time at constant temperature for attainment of equilibrium the melt was cooled and analyzed for oxygen. GAS SYSTEM A schematic diagram of the apparatus is shown in Fig 1. Commercial hydrogen is led through the safety trap T and the flowmeter F. The catalytic chamber C, held at 450°C, was used to convert any oxygen into water-vapor. A by-pass B with stopcocks was provided so that the hydrogen could be introduced directly from the tank to the furnace when desired. From the catalytic chamber the gas passed through a water bath W, kept at the desired temperature by an auxiliary heating unit, so that the gas was burdened with approximately the proper amount of water vapor before it was introdvced into the saturator S. All connections beyond the catalytic chamber were of all-glass construction. Those connections beyond the water bath were heated to above 80°C to prevent the condensation of water vapor. After the saturator, purified argon was led into the steam-hydrogen line at J, and finally the ternary mixture was introduced into the furnace. THE SATURATOR The saturator unit comprised three glass chambers, as shown in Fig 1, the first two chambers packed with glass beads and partially filed with water and the third empty. Each tower had a glass tube with a stopper attached for the purpose of adjusting the amount of water in it. The unit was immersed in a large oil bath, which was automatically controlled with the help of a thermostat relay to constant temperature, ± 0.05ºC, using thermometers which had been calibrated against a standard platinum resistance thermometer. The performance of the saturator over the range of experimental conditions was checked by weighing the water absorbed from a measured volume of hydrogen; the observed ratio was always within 0.5 pct of theoretical.

Jan 1, 1950

By H. M. Howe

Page 1. Introduction............................514 2. Definitions.............................517 3. Brevity of the Heating........................517 I. THE HARDENING OF THE BORE..............517 4. The Hardening of the Bore.....................517 5. The Thickness of the Hardened Layer.................517 6. Martensitization..........................518 7. The Hardening Repetitive ......................519 8. The Temperature Cycle.......................519 9. The Hardened Layer is the Merged Layer............... 521 10. The Progressiveness of Merging....................521 11. The Progressive Thickening of the Hardened Layer from Round to Round. 523 12. Merging and Hardening are Cumulative................523 13. Three Additional Causes of the Progressive Thickening of the Hardened Layer 525 14. Progressive Roughening of the Bore..................525 15. Avoidance of an Endothermic Transformation.............525 16. Asymptotic Retardation of the Thickening of the Hardened Layer.....527 17. The Troostitic Layer........................ 529 18. The Usual Lack of Martensitic Markings................529 19. The Thickness of the Hardened Layer Should Increase with the Quantity of Heat Taken up by the Walls of the Bore.................530 20. The Decrease of the Thickness of the Hardened Layer from Breech to Muzsle 531 21. Phstic Deformation as a Contributory aCause of Hardening........531 22. In What Way May Plastic Deformation Hasten Hardening?....... 535 23. Possible Need of Coarsening.....................535 24. Carburization as a Cause of Hardening..........:.....536 25. Does Hardening Increase Erosion?..................-538 11. THE CRACKING OF THE BORE ...............539 26. Appearance of the Bore and Cracks in Elevation............539 27. The Cracks in Elevation in the Rear Ring...............539 28. The Cracks in Elevation in the Forward Ring.............540 29. The Copper Network in the Grooves.................540 30. The Cracking of the Lands......................541

Jan 1, 1918

By W. Rostoker, A. S. Yamamoto, K. Anderko

ALTHOUGH the corrosion resistance of magnesium and its alloys is closely related to iron content, there has been no direct measurement of the solid solubility of iron in magnesium. Bulian and Fahrenhors;1 and Mitchel]2 agree that pure iron or a limited terminal solid solution crystallizes from the Mg-rich liquid. For this reason a magnetic-moment method was selected to estimate that portion of the total iron content which is not in solid solution. Since iron in solid solution in magnesium cannot contribute to ferromagnetism, the difference between chemical and magnetic-iron analyses should yield the solid solubility. By experimentation it was found that the melting of pure sublimed magnesium (99.995 wt pet purity) in Armco-iron crucibles at about 800°C is a convenient way to introduce small amounts of iron. Melts retained 5, 10 and 20 min at 800°C analyzed 0.003,, 0.005,, and 0.018 & 0.001 weight pet Fe, respectively, after being stirred, heated to 850°C, and cast into graphite molds. The as-cast alloys were pickled in acid (dilute HC1 + HNO3), annealed at 600°C for 3 days, scalped on a lathe to remove the pitted surface, pickled again, extruded at about 100°C to 3-mm wire, reannealed 41/2 days at 500°C, and water-quenched. The specimens were again scalped, pickled, and used both for chemical and for magnetic analysis. Most of the precautions described were intended to prevent iron pickup by contact with tools or superficial iron enrichment by volatilization of magnesium during heat-treatment. It is believed that the specimens ultimately used for test were homogeneous and characteristic of phase equilibria at 500°C. Magnetic Analyses A susceptibility apparatus of the Curie type was used for magnetic analyses. Field strengths of up to 10,400 oersteds could be generated. By this method, an analytical balance measures the force of attraction which a calibrated magnetic field exerts on a suspended specimen. The force equation is as follows f/m = M dh/dy where f/m = force per unit mass of sample M = magnetic moment per unit mass dH/dy = magnetic field gradient The dH/dy characteristic of the instrument is determined by the use of a standard palladium sample, and the calibration is made independently for all values of H. Since a large finite field is required to saturate an assembly of ferromagnets, it is necessary to measure the apparent magnetic moment for increasing steps of H until a saturation value is obtained. The percentage of iron in the sample as free ferromagnetic iron may then be computed simply C= 100 (M1/M1) where C = percent content of undissolved iron in sample M1 = saturation magnetic moment of sample per unit mass M1 = saturation magnetic moment of iron per unit mass taken as 217 emu-cm per gm There is no serious difficulty in applying this method except for the unusual magnetic behavior of very fine particles of ferromagnetic substances. It has been found and is the basis for a widely accepted theory that with sufficient subdivision, the magnetic fields required to saturate and the coercive force after saturation rise to exceedingly high values. Recent work on precipitates of Fe and Co from copper solid solutions8 showed that about 5000 oersteds were necessary to approach saturation. The magnetic moments as a function of field strength measured in the present investigation are listed in Table I. Only the 0.018 wt pet Fe alloy yielded a magnetization curve with a fairly well-defined saturation plateau at 3.76x10 -2 emu-cm/ gm. This corresponds to 0.017 & 0.001 wt pet Fe in the alloy. This indicates that the solid solubility must be of the order of 0.001 wt pet Fe. The magnetic-moment data of the other two alloys are badly scattered, indicating that the amount of ferromagnetic iron in these samples is so low that the magnetic forces acting on them cannot be measured accurately by the analytical balance used. Nevertheless, the fact that even the 0.003, wt pet Fe alloy shows ferromagnetism indicates that the solid solubility must be below that value. Acknowledgment This work was sponsored by the Pitman-Dunn Laboratory of Frankford Arsenal, Philadelphia, Pa. The support and permission to publish are gratefully acknowledged. References W. Bulian and E. Fahrenhorst: Zeic. Metallkunde, 1942, vol. 34, pp. 116-170. 2 D. W. Mitchell: AIME Transactions, 1948, vol. 175, pp. 570-578. 3 G. Bate, D. Schofield, and W. Sucksmith: Philosophical Magnsine, 1955, vol. 46, pp. 621-631.

Jan 1, 1959

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By G. R. St. Pierre, M. J. Pool, R. Speiser

The activities of chromium in solid Cr-Ti solulions contaitning from 10 to 90 at, pct Cr were measured over the temperatutre range 1250" to 1380°C. The Knzudsen effusion technique with direct weighing of the Knudsen cell was used. This was possible because the vapor pressure 0f chromium is about 600 times greater than the capor pressure of titanium so that the amount 0f titanium effusing could be neg-Lected. the activities of titanium were determined by g-raphical integration of the Gibbs-Duhertz equatiotz. The solutio~ls sllcdied exhibited positive deviations from Raoult's law, but they approached ideality as the temperature was raised from 125 to 138t C. The integral free energy of mixing was calclated from the activity values. AF has a maximum value of - 1.66 kcal a1 1390°C and a composition oj 55 at. pcl Cv. The free energy of formation of 'TiCr, is —0.76' lzcal a1 1250°C. The heats and entropies of mixing usere determined using the second law and thus tile mlues could be in error by a considerable amount. The Cv-Ti system is not a regular solution. ThE increasing emphasis on application of various models to alloy formation and solution behavior has led to an intensified interest in the thermochemistry of alloys. In a majority of the cases where different models have been applied the alloy system used was a simple one. However, the amount of data available on more complicated systems is small and in order to fully understand the behavior of metallic solutions more experimental work has to be carried out on these systems. The Cr-Ti system is reasonably complex and even though this system was being investigated as early as 1937 by Kroll,' no previous work has been done on the thermodynamic properties of either the liquid or solid state. This research was undertaken to determine the thermodynamic properties of solid Cr-Ti alloys. EXPERIMENTAL PROCEDURE The experiments on the Cr-Ti system were carried out in a water-cooled metal vacuum system. This system is composed of a brass vaporization chamber wound with copper tubing for cooling purposes, a brass liquid-nitrogen trap, an oil diffusion pump, and a Duo-Seal forepump. The pressure in the system is measured with an ionization gage. The interior of the vaporization chamber is shown schematically in Fig. 1. The Knudsen cell is supported by the molybdenum tripod, and a magnetically operated shutter is provided to protect the Pyrex sighting glass against deposition of metallic vapors in the intervals between temperature measurements. Heating is accomplished by means of a 20-kw 450-kc Westinghouse oscillator. The susceptor in this case is 10-mil tantalum seamless tubing which also forms the outside of the sample container. The remainder of the sample container consists Of an im~ervims re-crystallized alumina crucible and a 10-mil-thick tantalum lid. Two holes are drilled in the lid. The diameters of these holes were measured with the calibrated stage of a "Tukon" microhardness tester. The thicknesses were measured with a micrometer. A Leeds and Northrup disappear ing-filament optical pyrometer was used to measure the temperature. This is sighted through the smaller of the two holes in the lid and corrections for the emissivity of the sample were not necessary since the ratio bf cell length to hole diameter was large enough to insure a hohlraum. The pyrometer was calibrated at the ~~t~~~l Bureau of Standards, and the correction for the Pyrex sighting window was determined in the laboratory. The titanium used in this investigation was obtained from Mallory-Sharon and the chromium from The Union Carbide Metals Co. The reported purities were

Jan 1, 1968

By L. M. Kaas

Production planning techniques, particularly a production scheduling model are proposed for use in taconite mining in Minnesota. Applications of the scheduling model, on a two-year mine plan, which evaluates the equipment involved, are detailed. Data and tables are included. INTRODUCTION Fifty years ago Walter Swart, a mining engineer investigating the Minnesota taconites for the Jackling interests, made this report: "There is no doubt in my mind that this taconite mining is a game worth playing and that it can be played to a successful finish. It seems now only a question of men, money, methods and details."' The prosperous industry envisioned by Swart and other taconite pioneers is today a reality. Its growth has been spurred by technological advances in mining and beneficiation, depletion of natural ore reserves, and improvement of the economic climate. However, the massive problems that were solved to make this development possible are only a foreshadowing of the questions of "men, money, methods and details" that will be encountered in the future. The increasing demands for higher quality taconite pellets have already forced producers to examine better methods of quality control for their operations. THE NEED FOR PRODUCTION SCHEDULING The maintenance of fairly constant crude ore characteristics is of major importance to mill quality control. Through careful mixing of ore from storage bins, the concentrator staff can partially reduce the deviations of the feed analysis from the analysis desired. However, the limited effectiveness of bin mixing systems has caused some mining companies to utilize large capacity blending piles to reduce grade variations. Although the analysis of material being reclaimed from such a pile is relatively uniform, raw materials still must be scheduled from the mine into the pile in such a manner that the average analysis of all material is close to the feed analysis prescribed by the mill. PRODUCTION SCHEDULING MODEL Minnesota taconite mining companies have used three analyses to estimate how a certain ore will react to concentration. These factors are the crude magnetic iron content of the ore, the iron content of the plant concentrate produced from the ore at a standard grind, and the grindability index of the ore. The actual laboratory tests used to determine these factors have been described by Apuli.2 These data are obtained from analysis of diamond drill cores, and are the established criteria used by mine planning engineers to formulate taconite production schedules. Variations in the grade of mine output should be controlled by any production scheduling system. However, to be truly practical, production scheduling methods must also consider many of the less tangible variables that affect mine operation. These include pit layout, available equipment, and ownership of ore leases. The number and scope of the variables inherent in this type of mine planning suggested that a computer simulation could be used to solve the problem. The preparation of information for use with a computer simulation program was the initial phase of this project. Meaningful data was developed from logs of diamond drill cores. Analyses were related to their respective areas of influence by means of mine maps, Fig. 1. The three assay variables and tonnages for each area were punched on cards. In addition to these values, a location code number was punched in the first eight columns of the cards. This code is explained as follows: Column 1 Bench number Column 2 Quadrant location as determined by mine reference lines Columns 3-5 East-west coordinate Columns 6-8 North-south coordinate The heart of any simulation techniques is a well engineered mathematical model. To develop a model for taconite production scheduling, the relationship between the three assay variables had to be established. Because changes in each analysis factor affect the mill circuits in different manners, a weighting system was used to determine the relative im-

Jan 1, 1967

By Robert P. Uhley, LeRoy Scharon

TEST gravity surveys were made in the Washington County barite district of Missouri on property owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maxi- mum difference in elevation being 400 ft in a distance of 3 ½ miles.

Jan 1, 1954

By Anthony Folger, Charles E. Straub

Kansas produced 38,150,878 bbl. of oil in 1928 and 40,658,170 bbl. in 1929, thereby retaining its rank as fourth among the oil-producing states of this country. Production for 1928 was less than that for 1927 (Fig. 1) because of a decrease in the number of completions, but the average initial production per well (Table 1) shows an increase due to the completion of wells of comparatively large capacity in the new Valley Center pool of Sedgwick County. This increase in average initial production per well was further augmented during 1929 by completion of additional wells of comparatively large capacity in the Valley Center pool and the new Greenwich pool of Sedgwick County. Production for 1929 exceeded that for 1928 and threatened to exceed all records except that of 1918, however, production was prorated in

Jan 1, 1930

By Allan E. Martin, Harold M. Feder, Irving Johnson

The cadmium-uranium system was studied by thermal, metallographic, X-7-ay and sampling techniques; special emphasis was placed on the establishment of the liquidus lines, The single inter metallic phase, identified as the compound UCd11 melts peritectically at 473°C to form a-umnium and melt containing 2.5 wt pct uranium. The cadmium-rich eutectic (0.07 wt pct uranium) freezes at 320.6°C. Solid solubilities in uraizium and cadmium appear to be negligible. Between 473°C and 600°C the liquidus line is retograde. NO publication relating to the cadmium-uranium phase diagram was found in the literature. The establishment of this diagram was of considerable interest to us because of a possible application of the system to the pyrometallurgical reprocessing of nuclear fuels. Analysis of liquid samples, metallographic examination, thermal analysis, and X-ray diffraction analysis were used to establish the phase diagram from about 300° to 670°C. Particular emphasis was placed on the establishment of the liquidus lines. The same system was concurrently studied in this laboratory by the galvanic cell method.' Both studies benefited from a continual interchange of information. MATERIALS AND EXPERIMENTAL PROCEDURES Stick cadmium (99.95 pct Cd, American Smelting and Refining Co.) contained 140 ppm lead as the major impurity. Reactor grade uranium (99.9 pct U, National Lead Co.) was most often used in the form of 20-meshspheres. This form was particularly suitable because it does not oxidize as readily as finer powder. The liquidus lines were determined by chemical analysis of filtered samples of the saturated melts. The liquid sampling technique is described elsewhere2 alumina crucibles (Morganite Triangle RR), tantalum stirring rods, tantalum thermocouple protecthecadmiumtion tubes, Vycor or Pyrex sampling tubes, and grades 60 or 80 porous graphite filters were used. Uranium dissolves in liquid cadmium rather slowly. In order to achieve saturation of the melts it was necessary to modify the procedure of Ref. 2 by the use of more vigorous stirring and longer holding periods (at least 3 hr) at each sampling temperature. The samples were analyzed for uranium by spectro-photometry (dibenzoyl methane method) or by polar- ography. The analyses are estimated to be accurate to 2 pct. Thermal analysis was performed on alloys contained in Morganite alumina crucibles in helium atmospheres. Standard techniques were employed; heating and cooling rates were about 1°C per min. For the determination of the peritectic temperature, Cd-10 pct U charges were first held for at least 50 hr at temperatures in the range 435° to 460°C to form substantial amounts of the intermediate phase. For the determination of the effect of cadmium on the a-p transformation temperature of uranium, charges of Cd-25 pct U (-140+100 mesh uranium spheres) were first held near the transformation temperature, with stirring, to promote solution of cadmium in the solid uranium. The holding times and temperatures for these treatments were 18 hr at 680°C for the cooling run and 28 hr at 630°C for the heating run. Alloy specimens for X-ray diffraction and metallographic examination of the intermediate phase were prepared in sealed, helium-filled Vycor or Pyrex tubes. Ingots from solubility runs and thermal analysis experiments also were examined metallographically. Crystals of the intermediate phase were recovered from certain cadmium-rich alloys by selective dissolution of the matrix in 20 pct ammonium nitrate solution at room temperature. Temperatures were measured with calibrated Pt/Pt-10 pct Rh thermocouples to an estimated accuracy of 0.3°C. However, the depression of the freezing point of cadmium at the eutectic is estimated to be accurate to 0.05°C because a special calibration of the thermocouple was made in place in the equipment with pure cadmium just prior to the measurement. EXPERIMENTAL RESULTS The results of this study were used to construct the cadmium-uranium phase diagram shown in Fig. 1. This diagram is relatively simple; it is characterized by a single intermediate phase, 6 (UCd11), which decomposes peritectically, and which forms a eutectic system with cadmium. The solid solubilities in the terminal phases appear to be negligible. An unusual feature of the diagram is the retrograde slope of the liquidus line above the peritectic temperature. The Liquidus Lines. The liquidus lines above and below the peritectic temperature are based on three separate solubility experiments. The data are shown in Fig. 1 and are given in Table I. It is apparent from the figure that the solubility data obtained by the approach to saturation from higher temperatures fall on substantially the same lines as those obtained

Jan 1, 1962

By Anders Carlson

NOTABLE advances have been made in the evaluation of oil-reservoir rocks from information furnished by core analysis. Among the physical data employed, per-meability is of primary importance. It may be assumed that the permeability of a core sample, considered as a property inherent to the nature of the porous medium only, is not markedly altered by the coring opera-tion, therefore some degree of accuracy is justified in the laboratory determination of permeability constants by means of homo-geneous flow media. To provide that such relatively simple determinations be sus-ceptible to duplication and consistent inter-pretation should prove advantageous in the prediction of subsurface flow conditions involving nonhomogeneous fluids. The air permeameter seems to fill most satisfactorily the need for rapid and fairly accurate determinations. Instruments that are similar in design and operation have come into general use. However, this has not resulted in an encouraging uniformity in the results obtained. Recognizing the value of reducing measured values to a common quantitative standard, the authors have sought to determine possible reasons for undue discrepancies and means for their elimination. This paper will be specifically concerned with three factors, which appear to be of some importance in the establishment of consistent permeability values: (I) design and operation of the permeameter, (2) preparation and mounting of the sample, (3) type of flow created in the sample.

Jan 1, 1940

By F. L. Holderreed

A choosy in what they would smelt. The furnace charge had to be coarse, and it had to be rich. They discarded fines in excess of about 1/10 the total weight. They wanted 10% copper content and fussed about anything with as low as 5%. They concentrated the copper content of the charge as much as they could by prior selection. They roasted off enough sulfur to further enrich the copper content of the succeeding fall of matte (a melt of cuprous and ferrous sulfides or Cu2S.FeS). Then they desulfurized the iron and fluxed it by carefully adding silica (quartz, not silicates) for a slag of lower density than the cuprous sulfide (Cu2S or white metal). After skimming off the slag, they further desulfurized the white metal by blowing the molten bath with compressed air. The result was blister copper. Yesterday Their techniques and furnaces? Some experimented with mechanically rabbled roasters, but their standard roasting practice was burning coarse sulfide ore in 250-ton heaps. These heaps, approximately 24 x 24 x 6 ft, were burned for about 75 days down to 6-10% sulfur. The turnaround time for a given roasting position was 100 days. Assuming the base was a hearth, the calculated rate of treatment was on the order of 0.004 tpd per sq ft.

Jan 1, 1971

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.' A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.' A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By Willard Jillson

WITHIN the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discovered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky's mountain railroads was completed. The coals of Kentucky are, broadly, separated into two geographic units-the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the State, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.-both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.S7 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85. per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent.

Jan 9, 1919

By E. Miller, K. Komarek, W. Johnson

The activity of aluminum in solid Cr-A1 alloys has been measured by an isopiestic technique between Cr-A1890' and 1126" and 13 and 80 at. pct Al. The integral free energy of mixing has a minimum value of —5600 cal per g-atom at 59 at. pct Al. The maximum solid solubility of aluminum in chromium was determined to be 43 at. pct Al, and the composition limits of the compounds CrA14, Cr4A19, and Cr5Al, at 1000"~ were found to be 79 to 80, 66 to 70, and 59 to 63 at. pct Al, respectively. The thermodynamic properties of the Cr-A1 system have been investigated as part of a thermodynamic study of aluminum-transition metal systems.172 Little information is available on the equilibrium properties of the Cr-A1 system. The heats of formation of solid Cr-A1 alloys have been determined by Kubaschewski and Haymer at 600" and low-temperature specific heat data have also been obtained.~ More extensive work has been performed on the phase diagram, and a compilation has been provided by Hansen and Anderko,~ their phase diagram at elevated temperatures being essentially based on the work of Bradley and LU.~ The high-temperature portion of the phase diagram shows an intermediate phase CrA14 decomposing peritectically at 1018°C and existing at 82 at. pct A1 at 1000°C. They also identified the compounds with solubility limits of 72 to 75 at. pct A1 at 1000°C, and Cr5A1,, existing at 61 at. pct A1 at 1000°C. The maximum solid solubility of aluminum in chromium at 1000°C was found to be 46 at. pct Al. These elevated-temperature data were obtained by examination of quenched samples and were considered as less precise than the lower-temperature data. Koester, Wachtel, and Grube7 have revised the phase diagram as a result of their magnetic susceptibility and X-ray study. The results of this work differ appreciably from those of Bradley and Lu at temperatures above 800°C. The CrA1, compound is given as existing between 79 and 81 at. pct A1 at 1000°C, and they do not indicate the presence of a CrA13 phase reported by Bradley and Lu. They also report the compound Cr4Alg as having solubility limits of 66 to 70 at. pct A1 at 1000°C, while Bradley and Lu show this compound stable only up to 870°C. Koester et al. state that the high-temperature modification of the compound Cr5A18 is stable down to 1125"C, and not 980°C as stated by Bradley and Lu, and that the low-temperature modification of Cr5Al, has a range of homogeneity of 58 to 63 at. pct A1 at 1000°C. They also report that the maximum solid solubility of aluminum in chromium is 43 at. pct A1 at 1000°C. APPARATUS AND EXPERIMENTAL PROCEDURE An isopiestic method was employed which has been successfully applied to the determination of aluminum activities in solid ~e-All and Ni-Al alloys. Alloy specimens were held at different positions in a temperature gradient and were equilibrated with aluminum vapor from an aluminum reservoir kept at the temperature minimum of an impressed thermal gradient in a closed alumina system. Diffusion of aluminum into the specimens occurred until equilibrium was reached, at which the partial pressure of aluminum in each of the specimens was given by the vapor pressure of the pure aluminum reservoir. The activity of aluminum referred to liquid aluminum as the standard state in a given equilibrated sample at temperature T could therefore be expressed by: vapor pressure of pure aluminum at _ the temperature of the reservoir Vapor pressure of pure liquid aluminum, at specimen temperature T Since both the temperature of the aluminum reservoir and the specimen temperatures were determined experimentally, and the vapor pressure of pure aluminum is known as a function of temperature,' the activity of aluminum in a given aluminum alloy of known composition could be calculated. Initial runs were made with samples consisting of pure chromium chips placed in alumina crucibles. These runs exhibited large inconsistencies, indicating that equilibrium was not attained. High aluminum content Cr-A1 alloy powders were therefore substituted for the pure chromium specimens. The starting composition of the alloys was adjusted through experimentation until the concentration change necessary to attain equilibrium was small. In this manner, consistent results were obtained in reasonable times. SPECIMEN PREPARATION Alloy specimens were prepared from chromium of 99.997 pct minimum metallic purity: with 0.028 to 0.038 pct H, 0.0002 pct N, and 0.27 to 0.46 pct 0 (Aviquipo, Inc.). The aluminum had a purity of 99.99+ pct and the following impurities: 0.003 pct Cu; 0.002 pct S; 0.002 pct Fe; 0.001 pct Pb; 0.001 pct Ga (Aluminum Corp. of America). Alloy powders were prepared from weighed mixtures of chromium and aluminum by double-arc melt-

Jan 1, 1969

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.' Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.' For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969