Search Documents

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.'-' The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By E. Lifshin, R. E. Hanneman

QUANTITATIVE applications of the electron micro-beam probe frequently involve the evaluation of complex mathematical expressions and/or the analysis of large amounts of experimental data. The purpose of this communication is to describe briefly a versatile and useful computer program system that is applicable to analyze rapidly a wide variety of practical microprobe problems. This system consists of a group of ten FORTRAN programs that can be stored on tape, cards, or in the memory disc of the computer. These programs, or links, can be run individually or in any prespecified sequence without interrupting the operation of the computer or without destroying information which is being transfered from one link to another. For the program system described here a GE-235 computer with disc storage was used, so that the DCHAIN method of program linking was employed. Included in the library are programs to: 1) initiate analysis of a new set of data and transfer control between all other programs in any predetermined manner; 2) generate theoretical calibration curves of composition vs relative intensity; 3) generate empirical deviation parameters from least-square fits of experimental calibration data from standards of known composition; 4) convert raw X-ray data to corrected composition; 5) determine inter diffusion coefficients by Matano analysis of con centrat ion -distance data on a uniaxial diffusion couple; 6) determine activation energies and frequency factors of temperature-activated processes such as diffusion; and 7) generate calibration curves for determination of the thickness of thin films using microanalysis. A detailed description of these computer programs and their underlying principles is available on request from the authors."' The first program to generate theoretical calibration curves of corrected relative intensities vs composition uses the Poole and Thomas atomic number correction' and the Philibert absorption factor' with a voltage-dependent mass absorption coefficient for electrons in the alloy. A modified Castaing fluores- cence correction is also used which includes the effects of both Ka and KO radiation and over voltage.' Once the theoretical curves have been calculated in 1 wt pct intervals, these results are least-squares fit to obtain Ziebold deviation parameters' which are stored in COMMON in the computer memory. The net discrepancies between the original theoretical calibration curve and the regenerated curve using the Ziebold parameter are computed. Although this link is explicitly written for K-K fluorescent interactions, it can be applied to K-L, L-K, and L-L interactions as previously disc~ssed."~ Similar programs have also been written to utilize the Wittry fluorescence correction, Birks combined corrections, and various other corrections.' These modified programs have proved to be quite useful for quantitative comparisons of the results of the various theories. The program for conversion of raw X-ray data to corrected composition includes corrections for drift, backround, and instrumental dead time. The corrected intensities are converted to composition by use of the Ziebold equation"2 and parameter obtained from the program system. The results can be obtained for either atom or weight fractions. In addition to accurately computing interdiffusion coefficients the Matano analysis program calculates least-square smoothed values of concentration, concentration gradient, and curvature for each point on the raw input concentration profile. In order to obtain high accuracies a unique method of performing a least-square polynomial fit to incrementally advancing profile segments which overlap is used.' This program has been successfully modified for use in ternary diffusion problems3 and can readily be modified to handle analysis of diffusion profiles which include phase boundary discontinuities. This link is generally applicable to analysis of interdiffusion data obtained by other techniques as well as by the microprobe. The primary function of the next program is to least-squares fit experimental diffusion data to the normal Arrhenius function: D = Doexp(-Q/RT), to obtain values of Do and Q. In addition the probable error and one, two, and three u statistical confidence limits of DO, Q, and log D are evaluated. This program is also directly useful for analysis of any other simple temperature-activated processes including conductivity, and certain deformation and chemical processes. The program to generate calibration curves for film-thickness determination using the microprobe is based on a numerical integration of the equation derived by Cockett and ~avis.' Values of film thickness obtained by this program for copper on various substrates are in good agreement with measurements made by other techniques. Versions of the above program system have been prepared for use with or without a remote teletype connection to the computer for processing on either a real-time or time-share basis. The instrumentation coupling a microprobe to a teletype for automatic data collection and analysis by the presently described program system has been reported elsewhere by the authors.' If teletype equipment is not used to communicate with the computer, standard methods of card reading and tape reading can be used. In either

Jan 1, 1967

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-A1 alloys has been measured up to the solubility limit for formation of aluminum nitride using the Sieverts method. The activity coefficient of nitrogen decreases slightly with increasing aluminum content in the range of 0 to 4 wt pct Al. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from fhe elements dissolved in liquid iron has been determined to be: ?F" = -59,250 + 25.55 T in the range from 1600º to 1750ºC. The solubility of nitrogen in liquid iron alloys and the interaction of nitrogen with dissolved alloying elements in liquid iron have been the subject of a number of research investigations.' Most of this work, however, has been reported for concentrations well below those necessary for the formation of the alloy nitride phase. Data in the concentration region near the solubility limit of the alloy nitride, particularly for systems exhibiting stable nitrides, are important in evaluating the denitrifying power of various alloying elements. They are also useful in determining the stability of a given nitride if it is to be used as a refractory to contain liquid iron alloys. In view of the importance of aluminum as a deoxidizing agent in commercial steelmaking and the fact that its nitride, AIN, is a highly stable compound and has merited some consideration as an industrial refractory, the following investigation was undertaken. The use of the Sieverts technique provided a measurement of the equilibrium nitrogen solubility in liquid Fe-A1 alloys as a function of nitrogen gas pressure up to 3.85 wt pct A1 in the temperature range of 1600º to 1750°C. The values obtained by the Sieverts method were checked by means of a quenching method in which liquid iron was equilibrated with an A1N crucible under a known partial pressure of nitrogen gas, and the solubility of A1N in liquid iron determined by chemical analysis. EXPERIMENTAL PROCEDURE The theoretical considerations involved in determining the solubility product of a solid alloy nitride phase in liquid iron by measuring the point of departure of the nitrogen gas solubility from Sieverts law have been discussed by Rao and par lee.' The principal problem is to determine the variation of nitrogen solubility in an alloy as a function of the pressure of nitrogen gas over it with sufficient precision to establish the break point in the curve at the solubility limit of the alloy nitride phase. A fairly large number of data points are required to do this. A second problem is the determination of the composition of the precipitated solid nitride phase. This is necessary in order to define completely the thermodynamic relationships. The Sieverts apparatus used to make the nitrogen solubility measurements in this investigation is of essentially the same design as that described by Pehlke and E1liott.l The charge materials were Ferrovac-E high purity iron supplied by Crucible Steel Co. and 99.99+ pct pure aluminum. Recrystal-lized alumina crucibles were used, and were not attacked by the liquid alloys. The hot volume of the system which was measured for each melt ranged from 46 to 50 standard cu cm and was found to decrease linearly with decreasing pressure and with increasing temperature. The temperature coefficient of the hot volume at 1 atm pressure of argon gas was essentially constant for all experiments at a value of -6 X 10-3 cu cm per "C. The melt temperature was measured with a Leeds and Northrup disappearing filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature scale was calibrated against the observed melting point of pure iron taken as 1536°C. The emissivity of all melts was assumed to be that of pure iron, taken as 0.43. The charge weights ranged from 110 to 140 g and the range of aluminum contents covered was from 0 to 3.85 wt pct. Aluminum additions were made as 12 to 15 wt pct A1-Fe master alloys previously prepared in the system under purified argon. The compositions of the master alloys were checked by chemical analysis and found to be in agreement with the charge analyses. Vertical cross sections of the master-alloy ingots were used as charge material for the equilibrations in order to minimize the effect of any segregation which might have occurred during solidification of the master alloys. Determinations of the solubility product of

Jan 1, 1964

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966

By J. H. Swisher

The rate of internal sulfidation of austenitic Fe-Ti alloys in H2S-H2 gas mixtures is controlled primarily by sulfur diffusion, with counterdiffusion of titanium playing a minor role. At temperatures below 1100°C, enhanced diffusion along grain boundaries becomes important. The rate of internal sulfidation at 1300°C is approximately equal to the rate computed from the sulfur diffusion coefficient. The diffusion coefficient of titanium in y iron has been determined from electron microprobe traces in the base alloy near the subscale interface. The solubility of sulfur in Fe-Ti alloys has been measured in the temperature range from 1150° to 1300°C. The equilibrium sulfur content is found to increase with titanium content, due to the large effect of titanium on the activity coefficient of sulfur. The Ti-S interaction becomes stronger as the temperature decreases. TITANIUM as an alloying element in stainless steels is an effective scavenger for interstitial impurities, carbon in particular. Titanium is known to form stable sulfides; however extensive thermodynamic data on the Ti-S system are not available. Schindlerova and Buzek1 have shown that the Ti-S interaction in liquid iron is moderately strong. There have been no previous studies of the Ti-S interaction in solid iron. Internal sulfidation of Fe-Mn alloys was the subject of a recent investigation by Herrnstein.2 He found the rate of internal sulfidation to be an order of magnitude greater than predicted from available solubility and diffusivity data. A satisfactory explanation for the discrepancy could not be given. In the present study, the solubility of sulfur in austenitic Fe-Ti alloys was measured using a standard gas equilibration technique. Fe-Ti alloy specimens were also internally sulfidized. The rate of internal sulfidation was measured as a function of temperature and alloy composition. Supplementary electron micro-probe measurements were made to provide additional information on the nature of the internal sulfidation process. EXPERIMENTAL The starting materials were alloys containing 0.12, 0.24, 0.38, and 0.54 wt pct Ti. The alloys were made in an induction furnace by adding titanium to electrolytic iron that previously had been vacuum-carbon-deoxidized. The major impurity in the alloys as determined by chemical analysis was carbon. The carbon content of the alloys averaged about 100 ppm; metallic impurities were presented in concentrations of 50 ppm or less. Specimens were made in the form of flat plates, 0.03 by 2 by 4 cm for the equilibrium measurements and 0.5 by 1.5 by 3 cm for the rate measurements. The experiments were performed in a vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction tube. In the gas train, flow rates of the reacting gases were measured using capillary flow meters. The source of H2S was a mixture of approximately 2 pct H2S in H2, which was obtained in cylinders from the Matheson Co. A chemical analysis was provided with each cylinder. The H2-H2S mixture was diluted with additional hydrogen to obtain the desired ratio of H2S to H2, and the resulting mixture was diluted with 30 pct Ar to minimize thermal segregation of H2S in the furnace. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over Pas. The samples used in the solubility measurements were analyzed for sulfur by combustion and iodometric titration. The subscale thickness in the internally sulfidized samples was measured on a polished cross section, using a microscope with a micrometer stage. Electron microprobe traces for titanium in solution were made on several samples that had been internally sulfidized. A Cambridge microanalyzer was used, and the known titanium content at the center of the specimen was used as a calibration standard. The procedure for the microprobe measurements will be described further when the results are presented. RESULTS AND DISCUSSION Equilibrium Data. Fig. 1 shows the sulfur concentration as a function of gas composition for three alloys equilibrated at 1300°C. The dashed line is based on data published by Turkdogan, Ignatowicz, and pearson3 for pure iron. The breaks in the curves are the saturation points for the alloys. The fact that the initial slope decreases with increasing titanium content indicates that titanium interacts strongly with sulfur in solution. To obtain information on the composition of the precipitating sulfide phase, the measurements described in Fig. 1 were extended to higher sulfur partial pressures. These results are shown in Fig. 2. (The initial portions of the curves are reproduced from Fig. 1.) The highest PH2s /pH2 ratio used is believed to be below the ratio required for the formation of a liquid sulfide phase. Time series experiments were used to study the approach to equilibrium in the samples. It was found that equilibrium with the gas phase was reached in less than 4 hr at 1300°C.

Jan 1, 1969

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By D. F. Kaufman, H. R. Spedden, A. M. Gaudin

MANY studies of comminution have been made to ascertain the size distribution of the product and to evaluate the work of comminution in the light of the size distributions of the feed and product. Up to now, these studies have been essentially statistical in character, that is, a certain lot of feed was subjected to comminution in some specified way, and the aggregate product was fractionated into sizes, thereby losing all knowledge of individual relationship of feed to product pieces. Radioactive tracers offer a means to do something in this respect which could not be done before, namely, to follow the rupturing of some particular piece in its normal environment of other pieces. That is, it permits going beyond the usual statistical limitations of size distribution studies to what may be termed a personalized or individualized study. The purpose of this paper is to present some preliminary experiments conducted with this tool. The method employed was to mark radioactively some constituent of a feed. It is possible, of course, to consider the preparation of two lots of material of which one is radioactive and the other is not, and to blend the two ahead of the comminuting step; but to do so is open to the objection that the two preparations may not be identical. Therefore a technique has been chosen that removes this objection by merely taking out a size fraction of a comminution feed, rendering that fraction radioactive by exposure to a neutron flux, and then by returning it to Table I. Size Distribution of Offspring Albite Particles Originally 28/35 Mesh and in Admixture with Other Sizes After Grinding 2 min in a Steel Ball Mill Specific Activity ' Cumu- Corrected Distrl- latlve Size for Back- butlon In Distri- Fractlon ground, Weight, Product, button, of Product, cpm/gm g Pctb Pct Mesh (A). (W) (P) (ZP) + 28 0 56.0 0 100.1 28/35 62.6 54.0 24.8 75.3 35/48 62.8 59.4 27.7 47.6 48/65 41.1 53.0 16.2 31.4 65/100 29.6 45.7 10.2 21.2 100/150 23.7 37.0 6.6 14.6 150/200 23.3 25.1 4.4 10.2 200/270 20.1 19.0 2.9 7.3 270/400 17.8 21.2 2.9 4.4 -400 22.9 25.2 4.4 — 100.1 a These activity determinations were made in rapid succession in the order given. The specific activity (Ao) of the active 28/35 mesh fraction of the feed was measured at the beginning, after the measurement on the 65/100 mesh size fraction of the product, and; The end. The decay-corrected activities at those times were 246.7, 241.0. and 236.9 cpm per gm. The weight (W0) of the active 28/35 mesh fraction in the feed was 55.0. b Example of calculation for P in the 65/100 mesh oroduct frac- A W tion; A = 29.6, W = 45.7, Ao = 242.7, Wo = 55.0: P = — x — Ao Wo = 0.102 = 10.2 pet. the remainder of the charge for the comminution experiment. A relatively simple procedure was developed by which albite, containing sodium, was activated in the M.I.T. cyclotron. The cyclotron makes highspeed deuterons which impinge on a beryllium target, thereby producing a concentrated neutron flux. The mineral was exposed to this flux for 2 hr. This treatment changed enough of the sodium to sodium 24 (14.8 hr half-life, 1.4 mev ß) as to make detection and measurement easy. The nuclear reactions taking place were: 11Na23 (n,?) 11Na24 (irradiation) 11Na24 ß,?,? 12Mg24 (decay) The detailed technique of the experimentation was as follows: 40 kg of hand-sorted, lump albite were crushed to pass 10 mesh. After careful mixing of the lot, a screen analysis was made. The whole lot of material was fractionated on standard Tyler screens from 14 down to 200 mesh. Samples for experiments were compounded from these fractions in accordance with the screen analysis. When it was desired to make an experiment in which, for example, the 28/35 mesh size fraction was to be studied, the blend of size fractions was made as indicated above, except that the 28/35 mesh size fraction was added only after irradiation in the cyclotron. The blended charge containing the activated albite was ground for 2 min in a laboratory ball mill with a steel ball charge of controlled size distribution. The ground product was carefully sized on a set of Tyler screens in a Ro-tap. Each size was analyzed for radioactivity by the use of an end-window Geiger-Mueller counter and standard scaling circuit. This analysis was carried out in detail as follows: a 20-g sample was placed in a Petri dish, packed carefully to obtain reproducible geometric distribution with reference to the Geiger-Mueller tube, and the activity was counted for a 2-min period. Several determinations of the activity of the active size fraction in the feed were made at various times to establish the decay in activity with time. Linear interpolation was used to evaluate the activity that the active size fraction in the feed would have had at any given instant. The ratio of the observed activity in a size fraction of the product to the activity that the active size fraction in the feed would have had at the same time gives the fraction in the product size that came from the irradiated size in the feed. The general formula for finding the distribution, P, of a specific individual size fraction in the feed

Jan 1, 1952

By Paul Billingsley

WHEN I was an undergraduate at the Columbia School of Mines, the mining curriculum was subdivided into two major branches's known respectively as the Metallurgical and the Geological Options, which diverged rather widely as the course progressed. When I duly elected the Geological Option, I believed, I am sure, that this divergence would continue throughout the years. The facts have proved otherwise. The mining industry is a closely knit entity in which the search for its raw materials, called mining geology, cannot be separated from the conversion of these raw materials into marketable form, called metallurgy. The mining geologist searches for materials which the metallurgist can utilize, and only such; and whenever an advance in metallurgy opens the gates for new materials, the geologist's problem is correspondingly modified. No better instance of this relationship can be given than that seen in the Salt Lake region in recent years. Our mineral industry here is of long standing. The three principal tributary districts, Bingham, Park City and Tintic, were discovered in the 1860's and have been vigorously and intelligently developed for many decades. Their production has made the Salt Lake valley one of the world's great smelting centers. The maintenance of this industry has for years depended upon the continual development of new orebodies to take the place of those being extracted. Intensive exploration in the old districts has been supplemented by prospecting in outlying districts of lesser prominence. . Many new orebodies have been discovered, such as those of the Daly West, Silver King, and Judge mines in Park City, the Utah Apex in Bingham, and the Sioux, Colorado Chief Consolidated and Tintic Standard in Tintic. New mines in other districts have been discovered also, but without affecting the dominance of the three major districts. In all cases discoveries, to be of value, had to be of ore amenable to treatment in the available metallurgical plants. This meant that, for the most part, zincy ores, both oxide and sulfide, must remain untouched, and also that ores high in iron and ores high in silica had a fictitious value, either high or low, set by the balance of these

Jan 1, 1928

By H. E. Brauer

PART I INTRODUCTION Among the zinc base alloys used for casting in metal moulds, particularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortness which facilitate casting. Objection to the use of these alloys may bee raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intercrystalline corrosion. In all cases which have come to our knowledge where the conditions of service were known, failure has occurred upon exposure to moisture and heat varying from a hot moist atmosphere to high pressure steam. Moreover, the alloys described in all such cases contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intercrystalline oxidation in zinc-aluminum alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Bauer2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the most part, and Rawdon's3 examinations were made on an alloy containing 0.4 per cent. lead also exposed to the Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to determine the exact nature of this phenomenon and the effect of other metals present as impurities or intentional additions in accelerating or-retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation.

Jan 8, 1922

By Carville E. Sparks, Rollin Farmin

TRIAL installations of rock bolts, of the slit-rod-and-wedge type, were under way at several units of Day Mines, Inc., when Korean hostilities interrupted the already slow deliveries of steel bars to the Coeur d'Alene district. Factory-made bolts had not yet been put on the local market, so the program was halted for lack of supplies. Interest was revived by a visitor's description of wooden roof bolts. These were said to have been used briefly with apparent success in a coal mine, until apprehension voiced by the U. S. Bureau of Mines caused the practice to be suspended. To make wooden bolts for trial in ground support, Day Mines acquired a second-hand doweling machine equipped with two cutting heads, one to turn out the desired round rods of 2-in. diam, the other to turn out 1-in. rods to be used as powder-tamping sticks. This machine was installed in the all-weather sawmill of the Hercules mine unit at Burke, Idaho, where fabrication of the wooden bolts commenced early in 1951. Most of the mining in the Coeur d'Alene district is along steeply dipping veins in shaly quartzite and argillite of Algonkian age. Ground support commonly is required in zones where the rocks have been sheared, brecciated, and hydrothermally altered. Pressure from the sidewalls is more troublesome than weight overhead, but both increase with the size of the mine opening. Caving may come from a progressive sloughing of irregular rock fragments or from an exfoliation and buckling of the layered wall rocks. The disintegration is thought to develop from an initial elastic expansion of the rock toward the newly-created mine opening, followed by the dilation of many tiny partings in the rock by absorption of water. As the partings widen, masses of rock develop weight and become free to fall. The function of rock bolts is to prevent or retard widening of partings in the rock supported. Wooden Bolts, Wedges and Headboards Bolt assembly used by Day Mines consists of a bolt 4 or 6 ft long, two wedges 16 in. long, and a headboard 30 in. long, Fig. 1. All four pieces are made of local red (Douglas) fir, either green or well-soaked in the mill pond before it enters the sawmill. Bolts are fabricated from cants, 2 1/4 in. sq, cut from relatively straight-grained timber with a minimum of knots and trimmed to 4- and 6-ft lengths. The bolt then is turned in the doweling machine from 21/4 in. sq to 2 in. diam round, except for a 4-in. length at one end which is left full square to provide the striking head and the shoulder that holds the headboard in position for wedging. The foot end of the bolt is slit with a thin saw for a length of about 16 in., thereby making a slot to receive the wedge against which the bolt is driven for anchorage at the bottom of the rock hole. A similar slit, 12 in. long, is made in the opposite (head) end of the bolt to receive the second wedge, which crowds the headboard against the ground at the collar of the rock hole and puts the bolt in tension. The second slot is aligned 90" from the plane of the first slot to avoid Longitudinal splitting and is notched out slightly to allow easier insertion of the collar wedge after the bolt has been driven to bottom. To prevent splitting the headboard by spreading action of the head wedge, this slot is oriented at 90" to the grain of the headboard when the pieces are assembled, Fig. 2. The wedges are similar to standard mine wedges, but more slender; they are cut 1 7/8 in. wide and 1 in. thick at the heel and taper out in 16 in. of length. The headboard, or bearing plate, is not necessary for some types of ground but generally is desirable because it helps the bolt to support an area of loose, friable rock and reduces the tendency for the rock at the collar of the hole to split away from the wedged head by distributing the pressure over a wider rock surface. The headboard may be a 24-to 30-in. length of 3-in. plank, 8 to 12 in. wide, but a similar length of rounded sawmill slab serves equally well at 20 pct of the cost. A hole of 2-in. diam is bored or punched through the center of the headboard, either at 90" or at various high angles to its surface. The bolt is inserted to its shoulder through this hole, then driven into the rock hole. Bolts, wedges, and headboards are given a full timber preservative treatment to inhibit rot. Bundles of each are immersed in a warm saturated solution of Osmose salts in water for 48 hr, removed, dripped dry, and stored in a relatively humid underground depot to cure. Most wooden rock bolts used by Day Mines are 4 ft long. Holes to receive them, about 42 in deep and 2 1/8 in. in diam, are drilled into the rock' to be supported, nearly normal to the periphery of the mine opening. The type of drill used is dictated by convenience: stoper, jackleg, or jumbo-mounted drifter. Correct depth of the hole is assured by use of a measuring stick that has been cut to the proper distance from drill chuck to the ground at the collar of the hole when a standard length drill rod is at the bottom. The bolt is seated to the shoulder through the hole in the headboard, the foot-end wedge is placed in its slot, and the assembly is inserted into the rock hole. Then the bolt is driven until it is seated solidly on the wedge against the bottom of the rock hole. Driving may be by hand with a sledge, or

Jan 1, 1954

By Paul Billingsley

When I was an undergraduate at the Columbia School of Mines, the mining curriculum was subdivided into two major branches's known respectively as the Metallurgical and the Geological Options, which diverged rather widely as the course progressed. When I duly elected the Geological Option, I believed, I am sure, that this divergence would continue throughout the years. The facts have proved otherwise. The mining industry is a closely knit entity in which the search for its raw matcrials, called mining geology, cannot be separated from the conversion of these raw materials into marketable form, called metallurgy. The mining geologist searches for materials which the metallurgist can utilize, and only such; and whenever an advance in metallurgy opens the gates for new matcrials, the geologist's problem is correspondingly modified. No better instance of this relationship can be given than that seen in the Salt Lake region in recent years. Our mineral industry here is of long standing. The three principal tributary districts, Bingham, Park City and Tintic, were discovered in the 1860's and have been vigorously and intelligently developed for many decades. Their production has made the Salt Lake valley one of the world's great smelting centers. The maintenance of this industry has for years depended upon the continual development of new orebodies to take the place of those being extracted. Intensive exploration in the old districts has been supplemented by prospecting in outlying districts of lesser prominence. Many new orebodies have been discovered, such as those of the Daly West, Silver King, and Judge mines in Park City, the Utah Apex in Bingham, and the Sioux, Colorado Chief Consolidated and Tintic Standard in Tintic. New mines in other districts have been discovered also, but without affecting the dominánce of the three major districts. In all cases discoveries, to be of value, had to be of ore amenable to treatment in the available metallurgical plants. This meant that, for the most part, zincy ores, both oxide and sulfide, must remain untouched, and also that ores high in iron and ores high in silica had a fictitious value, either high or low, set by the balance of these

Jan 1, 1928

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By C. L. HUNTZINGER

THE mine here described is in the Witbank district, a coal area of the Transvaal, about 100 miles north- east of Johannesburg. and is owned by the Witbank Colliery, Ltd. The plant has a capacity of 4000 tons per eight hours, and prepares five sizes of coal. The coal seam lies at a depth of about 200 ft. below the surface, and is reached by an inclined shaft sunk at an angle of 18° with the horizontal. Although the thickness of the coal seam varies from 10 to 14 ft. or more, only about a 7-ft. bench is mined. Mining is by the hord and pillar system. Bords are driven 18 ft. wide, with pillars measuring 18 ft. square. The mine is laid out into four sections, each sewed by a main haulage way from the shaft. Arc-wall machines are used for cutting the coal. but all loading is done by hand. Native labor is employed under the supervision of white miners, who do the required blasting. The workings are practically free from gas and water, and very little timber is needed.

Jan 1, 1931

By Richard P. E. Hermsdorf

IN the nonferrous sessions this year, magnesium wiggled its way into a dace of prominence such as it has never before enjoyed. This was evidenced not only by the number of papers presented on that metal but by the attendance at the meetings. The atmosphere permeating these magnesium meetings was similar to that which exists in a family with a new baby. Everybody crowded around to see what it looked like and then wondered whether it would be a success and credit to the family. Well. magnesium appeared to be a vigorous youngster, full of life, and raring to go. A close relative of maenesium named " aluminum, although much more grown up, also attracted much attention. From the activity and spirit in these sessions

Jan 1, 1944