Search Documents

THE Searles Lake orebody is located in the north- west corner of San Bernardino County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which differ in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor.

Jan 2, 1954

By K. H. Coats

In tnany oil and gas fields, significant investments are required in piping networks for collection, injection and disposal of various fluids. This paper treats the problem of optimally locating the trunkline(s) for a given systet to nlinimize both the total length of piping connecting the individual wells or lease batteries to the trunkline and the length of the latter. Single and multiple trunklines, varying line sizes, and grouping of wells are considered. Some attention is paid to the case of a curved trunkline. A field case is treated and conclusions are that the problem of locating a single trunkline is relatively straightforward while the location of multiple trunklines requires further research. INTRODUCTION la many oil and gas fields, significant investments are required in piping networks for collection, injection and disposal of various fluids. A single field may concurrently require piping systems for gathering of oil, gathering of gas, injection of water or gas and disposal of salt water. Two problems arise in the consideration of any one of these networks. The first involves the sizing of the various segments of the network to minimize piping and compression costs. The second problem, treated herein, is that of optimally locating the trunkline(s) for a given piping system to minimize the total length of pipe connecting the individual wells or lease batteries to the trunkline. This minimization problem may arise in field automation if it involves replacement of individual lease batteries by a central field battery which will require trunklines and connecting pipelines to individual wells. The problem also arises in connecting a gas pipeline through a subsidiary trunkline to wells in a gas storage field. The first analysis given below treats the case of a single trunkline and of separate connecting lines for all field units.* The analysis is then extended to consider multiple trunklines and common connecting lines for groups of field units. Varying sizes, and therefore costs, of the connecting lines are taken into account. A simplified development is given to illustrate the manner in which line sizing calculations may be integrated with the line placement problem. This study is primarily directed toward the placement of straight trunklines, although for certain field shapes or well distributions curved trunk-lines might be preferable. Some mathematical consideration is therefore given to the placement of a curved trunk-line in a field. The determination of optimal locations for two or more trunklines involves some difficulties which are discussed below. The need for further research in this area is emphasized. The problem of a single trunkline is solved in relation to an actual oil field. The problem of optimally locating two trunklines in the same field is also treated and the results are compared to the single-trunkline case. All calculations reported were performed on an IBM 7072 digital compker. The importance of right-of-way, roads and terrain in locating trunklines and connecting lines is realized. The present analysis is advanced on the premise that in planning piping networks one should start with the optimal conditions whenever possible and proceed therefrom.

By R. Roberge, H. Herman

Jan 1, 1969

By N. F. Fiore, M. C. Mangalick

DISLOCATION damping in single crystals is orientation dependent.&apos; If dislocations are distributed uniformly over all the slip systems in a crystal, and if each dislocation contributes identically to the damping process, then a damping loss or decrement 6 arises. In fact, however, for a crystal of axial direction (hkl), dislocations on certain slip systems are oriented to make a larger contribution to the damping loss than are dislocations on other slip systems. Thus the measuring damping, 6 (hkl) is proportional to an orientation factor (hkl), which weights the ability of each slip system in the crystal to contribute to the total damping. If it is assumed that dislocations are distributed uniformly on all slip systems, then for a given orientation of an fcc crystal this factor is determined2,3 by the three nonzero elastic constants Cll, C12, and C44 and the density p. In this communication measured values of elastic constants for two Fe-18Cr-Ni alloys are reported, and the dislocation damping results on two different orientations of each alloy are analyzed for orientation dependence. Elastic constants were determined by measuring the ultrasonic velocities of one longitudinal and two shear waves in (110) direction of the fcc crystals.4 Variation of velocities with the change in orientation is very small for (110) orientation,3 and so this direction is ideal for orientation factor and comparative damping measurements. Experimental Procedures. The nominal compositions of the alloys studied are given in Table I. These alloys were vacuum-melted and vacuum-cast from high-purity materials at U.S. Steel Applied Research Laboratories. The single crystals were grown by the modified Bridgeman technique. The specimens were homogenized at 1350°C for 20 hr, cut to shape and size with a spark cutter, and then annealed at 1100°C for 20 hr prior to use. In the KHz frequency range, the Marx composite piezoelectric oscillator was used to obtain the damping. The ultrasonic pulse technique was used to measure the ultrasonic velocities and the attenuation in the MHz frequency range. M.c.mANGALICK,-- StudentMemberAIME,formerly Research Assistant, University of Notre Dame, is now with Casting Laboratory, Chase Brass and Copper Co., Cleveland, Ohio. N. F. FIORE, Associate Member AIME, is Assistant Professor, Department of Metallurgical Engineering and Materials Science. University of Notre Dame, Notre Dame, Ind. This communication is part of a Ph.D. thesis presented by M. C. MANGALICK to the Graduate School of the University of Notre Dame. Manuscript submitted May 20. 1968. IMD Elastic Constants. Table I gives the values of the ultrasonic velocities. Values of C11, C12, and C44 calculated from these velocities are also given in Table I, and it is evident that there is very little variation in C11, C12, and C44 with nickel content. This slight variation may be attributed to inaccuracies in velocity measurements and practical differences in the orientations of the specimens. For example, in B the time interval for vl was 2.4 ± 0.05 sec giving an error in v1 of 0.235 x or 0.005 in. per sec. The elastic constants obtained by pulse technique were tested by calculating E<110>, Young&apos;s modulus for the (110) direction, from the equation: This value was compared with the value computed from the resonance bar measurements in which where fr is the resonance frequency and I, is the length of the specimen. In all cases, the values calculated from the ultrasonic velocity measurements

Jan 1, 1969

By F. D. Rosi

IT was recently shown1 that slip bands can be observed in bent germanium crystals after deformation, by means of etch pits along the slip traces. It is the purpose of this note to show how chemical etch pits can also be usedto examine the appear- ance of slip bands in silicon, as well as other deformation markings. A 30 ohm-cm, p-type single crystal bar, 2x1/4x1/8 in., was plastically bent at approximately 1200°C in a vacuum of 1x10-5 mm Hg. The axis of the crystal was coincident with a <III> direction, and the surface normal to the axis of bending was within 4" of a (110) plane. Prior to the deformation, the (110) surface was mechanically polished with

Jan 1, 1958

A LARGE proportion of the steel that is melted and refined in the United States and poured into ingots is made in basic open- hearth furnaces. The capacity of these furnaces varies over a wide range with a large majority falling within limits of 50 to 200 tons (Fig. 1) The two general types of furnace design used are stationary [ ] and tilting furnaces, the former being much more common. The fuel burned in such furnaces is either one of several types of gas, or a liquid fuel such as oil or tar, or a combination of gas and liquid fuel. GENERAL FEATURES OF FURNACE CONSTRUCTION The design of a modern stationary furnace built to burn liquid fuel and with a capacity of 175 tons is shown in Figs. 2 to 4. The cross- section of the furnace at the tap hole is illustrated in Fig. 2, which shows the bottom construction, sloping back wall, and the rigid steel

Jan 1, 1944

W ho holds title to the continental shelf? As submarine mineral ventures move out into deeper and deeper waters, the dispute over this question is bubbling up with greater and greater urgency. Basically, the forces of disagreement are lined up on two fronts--one nationalist and the other internationalist. The nationalists, or "broad shelf" proponents, view the shelf as a geologic extension of the coastal nations and therefore subject to the sovereignty of these nations. The internationalists or "narrow shelf" proponents, seek to circumscribe the jurisdiction of the coastal nations by a topographic line beyond which all rights would be reserved to an international regime. In the U.S. public sector, three groups----the American Bar Association and International Law Association committees and the National Petroleum Council (NPC) - have taken a stand on the broad shelf. These are joined by AIME, which has consolidated its position in a "Policy Statement on the Outer Limit of National Sovereignty Over Seabed Resources." This statement was adopted by the AIME Board of Directors last October 15 after its submission by Earl Cook, Chairman of the AIME National Affairs Committee, at the behest of the Society of Petroleum Engineers. The main organization holding to the narrow shelf is the Commission on Marine Science, Engineering and Resources.

Jan 1, 1970

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920&apos;s, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco&apos;s Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

By David White

ATTENTION has been given to the sources and supply of the raw vegetal matter and. the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic debris, and of the biochemical changes-undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of :this debris, and the deposition, as, sediments, of the undecomposed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal solution.1 BIOCHEMICAL CHANGES END IN PEAT FORMATION The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly unconsolidated, and their water content is great, amounting to over 85 per cent. near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed.

Jan 2, 1925

Meeting, of Jan. 22, 1915.-Dr. Albert R. Ledoux was unanimously nominated-by the Board as one of the representatives of this Institute upon the Engineering Foundation Board. The following Tellers to count the votes for officers and directors on Feb. 16, 1915, were appointed: David H. Browne; Arthur S. Dwight, and Bradley Stoughton; and the following Tellers to count the ballots, on the amendments to the Constitution: Arthur L. Walker, Max Roesler, and Burr A. Robinson. Karl Eilers was appointed a member of the Library Board of the United, Engineering Society, representing this Institute in place of C. R. Corning, ;resigned. The Pick and Hammer Club of the University of Oklahoma was established as an Affiliated Student Society. The sum of $150 was appropriated to the Columbia Local Section. The sum of $29.50 was appropriated to the Chicago Local Section.

Jan 3, 1915

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation&apos;s bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation&apos;s bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner &apos; A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.&apos; Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins&apos; observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins&apos; has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200&apos;C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By Henry Morris

AS STATED last year, in a similar review by David White and the author, any review of the petroleum industry purporting to cover such a wide field can only mention the principal facts. This incompleteness is necessitated not only by the limitations of space, but by the delay in receiving detailed information. The principal feature of the year, in Europe, was a material increase in the consumption of petroleum products, and a notable decline in prices. Although there we relative increases in production in Roumania and Poland, the total did not by any means keep pace with the increase in consumption, which, as usual, was supplied "from America and both the Near and Far East. The interest in Asiatic production, as usual, centers around the Persian fields, which, according to the annual report of the Anglo-Persian Oil Co. published at the close of last year, it was estimated would amount to 3,775,000 tons by the close of the fiscal year, March 1, 1924. Russia also showed an increase in production. In Africa there was nothing of outstanding interest in production, although Egypt showed a decrease and the goverment refinery at Port Said was closed.

Jan 3, 1924

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron&apos; and molybdenum.&apos; The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,&apos; containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln&apos; wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,&apos; mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953

THE RELATION OF THE ENGINEER TO RECONSTRUCTION FIFTY-THIRD MEETING OF BOSTON SECTION The fifty-third meeting of the. Boston Section was held April 28. The speaker of the evening was the new president of the Institute, Mr. Howard V. Winchell, who spoke on "The Relation of the Engineer to Reconstruction." He told of the part engineers had played in the war and paid tribute to Herbert E. Hoover as an example of what engineers can do. He said that engineers are not taking enough interest in politics, although it is badly needed as shown by the evidences of Bolshevism even in America. Conditions have suddenly changed; whereas we formerly borrowed money we are now loaning widely to foreign countries and our investments, abroad have to be protected. A committee is badly needed to investigate and determine the actual conditions. The Government has already been invited to cooperate with the Institute along professional lines and this should lead to closer contact between our Society and the Government. Mr. Winchell then went on to describe some of the mining conditions in Russia. He brought out the point that the rich platinum deposits are exhausted and only the poorer sands remain. The largest copper properties average less than 2 per cent. copper and there are some 4,000,000 tons available in .the Caucasus region near Batum. There are approximately 100,000,000 tons of high-grade manganese ore scattered in small deposits in the eastern Ukraine. There are some copper mines in the East, butt they are almost exhausted. The Baku oil field is the second largest in the world and there is probably oil in Persia. There are also manganese in Siberia and coal veins of enormous thickness.

Jan 7, 1919

By R. E. Johnson, J. W. Donaldson, D. B. George

Accurately predicting the minor element content of an anode product is an important part of an evaluation of copper smelting processes. A general review of the minor element behavior in copper smelting is presented with the techniques to predict anode quality as a function of important process variables. Among variables considered are concentrate composition; recycle of dust, sludges and other intermediate byproducts from smelters and refineries; and other important smelting variables, including matte grade and the slag cleaning process. To evaluate the complex nature of minor element behavior relative to these variables, special techniques have been developed and are described.

Jan 1, 1976

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,&apos; and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By Edwin T. Wood

THE term blending as used herein refers to the mixing of ores assaying more than 0.20 pct U3O8 with low grade material assaying less than 0.20 pct U3O8. Such blending when properly understood and controlled will produce more total dollars of profit from many mining ventures. The question whether or not to blend is particularly vexing when an orebody is surrounded by an envelope of low grade material or separate tonnages of low grade exist which could be extracted coincident with the higher grade ores. Should any, all or part of this low grade be mined? If so, in what proportion and what is the limiting assay of the low grade material?

Jan 7, 1958