Search Documents

By J. R. Maxwell

Large capacity flotation cells with volumes ranging in size from 300 to 2000 cu ft are used in the Opemiska concentrator, Opemiska Copper Mines (Quebec), Canada. This paper gives a description of the flowsheet with metallurgical comparisons using Maxwell vs. conventional cells, total power consumption used, and estimated maintenance costs.

Jan 1, 1973

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;' the direction and the driving force of grain boundary sliding and migration;' the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.' It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954

By C. Wachmann

The theory presented ill this paper makes possible examination of the phenomenological aspect of secondary oil recovery by alcohol flooding. Limitutions of the theory are contingent on three primary assumptions: (1) chemical equilibrium, (2) no fingering, and (5) no dispersion. The second assumption implies one-dimensional flow. In a geometric sense the theory extends the Buckley-Leverett construction to systems of two slightly miscible fluids and to systems of three components. This is made possible by considering single-phase fluids to be made up two phases, namely of an excess of one phase and a negative amount of the other phase. The procedure is discussed in the paper. The theory also permits direct determination of the relationship between the aqueous phase saturation and the concentration of water in the aqueous phase in a zone of variable composition. The velocity of planes of constant water concentration and of constant saturation can be computted likewise and the existence of saturation discontinuities inferred. Consequently the behavior of such a Zone, which may exist at some time between a displaced and a displacing fluid, May be determined. mathematical details are given in Appendices. Problems of experimental verification are pointed out on the basis of a supporting experiment. Implications of the theory and effects of violations of primary assumptions are discussed briefly. The major conclusion is that, if the primary assumptions are met, with pure alcohol and alcohol-rich .slugs piston-like displacement of oil and water is possible. INTRODUCTION The recovery of oil from porous media by alcohol displacement has been studied for several years. Extensive experimental investigations into alcohol flooding have been carried out in the laboratory although little has been done in the field. A large amount of practical information is available, the extent being indicated by the first three papers cited 1-3 and their respecrive bibliographies. This has permitted the Formulation of inferential theories. A more analytical approach in which theories are developed primarily by reasoning from known physical principles and relationships has, however, lagged behind. In fact, an analytically derived theory of alcohol displacement has not been available. The theory presented in this paper on oil and water displacement by alcohol from a porous medium is a result of the analytical approach. The theory is idealized, as certain assumptions had to be made to make the mathematics tractable and reduce complexity of argument. In particular, major assuptions concerning conditions of equilibrium, interfacial stability, longitudinal mixing, etc., led to the exclusion of fingering, for example, from all considerations. In many laboratory experiments reported in the literature fingering could not be avoided. There is, therefore, disagreement between theories based on experimental evidence available and the analytically derived theory presented here. This theory presented is based on known physical data and makes use of the Buckley-Leverett construction and its suggested extension. The mathematical derivation of the theory is given in Appendices. Three examples relevant to alcohol displacement are discussed to explain the use of this theory: (1) system of two immiscible fluids (the Buckley-Leverett case); (2) system of two slightly miscible fluids involving an extension of the Buckley-Leverett construction; and (3) system of three components, including injection of pure alcohol or alcohol-rich fluid as a special case, which involves a more general extension of the Buckley-Leverett construction. In these discussions strict assumptions were made to impose equilibrium conditions and exclude mixing and fingering. Effects of relaxing these assumptions and consequent extensions of the theory are indicated. The complexity of the alcohol displacement process makes experimental verification of the theory essential. Some relevant evidence is offered in this paper.

Jan 1, 1965

By R. W. Raymond

AT the Liége meeting of the Iron and Steel Institute of Great Britain, in August, 1873, and also at the Vienna Convention of Mining and Metallurgical Engineers, at the end of August, and at the convention of German geologists, at Wiesbaden, in the first part * Extract from the President's address.

Jan 1, 1874

By Frank A. Wardlaw

My subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanida-tion plant. During the process of development, sulfide ore was found assaying about 5 per cent. copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direet-smelting lead ore was also mined. In 1918 and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation concentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. Results of Selective Flotation In 1924 the mine was on the point of a shutadown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the International Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

By H. S. Munroe

As elaborate discussion under this heading formed a chapter in one of the reports made by Professor Raymond as Commissioner of Mining Statistics." In a subsequent report? was printed a paper., by Mr. William Main, Jr., of Columbia, South Carolina, containing a theoretical investigation into the effect of the velocity of impact on the effective ditty of stamps. A visit to the Lake Superior copper region last summer suggested an inquiry into the relative efficiency and economy of the enormous steam stamps of the copper-mills, as compared with the results obtained with the cam and tappet stamps commonly used in the West. The atmospheric stomp used at the Phoenix Mill promised to add interest to the inquiry, as giving an example of unusually high speed, this stamp making 160 drops per minute. In introducing his subject Dr. Raymond makes the following remarks, which are quite apropos of the present investigation: "In considering the economical application of stamping machinery, we meet, at the beginning, with serious difficulties in obtaining accurate data for comparison. The weight and fall of stamps vary as the shoes and dies wear out; and this may lead to a change of speed also. Moreover, defects in engines, boilers, or machinery for the transmission of power, may occasion serious losses, which cannot fairly be charged to the arrangements of the stamps proper. Again, the capacity of stamp-mills is directly dependent, in some degree, upon the nature and extent of discharge, fineness of screens, and other peculiarities of the battery. Finally the hardness and tenacity of the rock crushed varies so much that comparisons between different localities cannot be implicitly trusted. The safest experiments are those made in the same mill, by changing first one arid then another condition of working; but this is seldom possible for such

Jan 1, 1881

By J. Chipman, J. B. Gero, T. B. Winkler

D. C. Hilty—This paper is a useful and timely addition to our store of quantitative data relating to manganese distribution between slag and metal in steel-making processes. For some time, many of us have suspected that the values of Kmn derived by Körber and Oelsen might be too low, and this paper now appears to confirm that suspicion. Application of the new constant to openhearth data should prove interesting. The manganese deoxidation curves of fig. 4 agree fairly well with direct measurements of isothermal solubilities of oxygen in liquid iron containing manganese that have recently been made at the Union Carbide and Carbon Research Labs., Inc. According to the solubility data just mentioned, however, the curves for 1550" and 1600°C lie much closer to each other than the authors have indicated. In other words, the solubility measurements suggest that the logarithm of the oxygen solubility is not a linear function of the reciprocal of the absolute temperature, as the authors have assumed for their calculations. It seems possible that this discrepancy may be due in part to the authors' use of the distribution coefficient, L,,, obtained from Taylor and Chipman's curve for the solubility of oxygen in iron as shown in fig. 2. Taylor and Chipman gave the equation of this curve as —6320 Log % 0 - ---T + 2.734 Their data, however, can be fitted equally well by a curve having the equation: 13.23 x104 1.18x10" Log % O = 36.350 -13.23x10 Moreover, this curve also fits the authors' oxygen distribution data somewhat better than does the linear curve of Taylor and Chipman. Its use in the derivation of Lo for calculation of the deoxidation curves by the authors' eq 15 causes the effect of temperature on the calculated curves of fig. 4 to agree quite well with the temperature effect that has been observed. An experimental determination of the temperature coefficient of the manganese reaction appears to be desirable. J. E. Stukel—Because the authors have done such an excellent job, my comments will be confined to additional information. Very shortly Professor T. L. Joseph and I will publish the results of a study of the reaction between molten manganese and silica. It was found that electrolytic manganese, melted in silica crucibles, reacted with the silica to form a silico-manganese alloy containing 18 pct silicon (1500°C) and a silica saturated MnO-SiO, slag. Therefore, the presence of silicon and its oxides in the Fe-Mn-0 system will affect the equilibrium. Carbon is also an important factor. The higher the carbon content of the iron the less ability manganese has to reduce silica. As a matter of interest, recently a study of the manganese equilibrium in carbon saturated iron and blast furnace slags was completed at Carnegie Institute of Technology. As a comparison to the present study, 2 to 5 hr were required to reach equilibrium and temperature was a much more important factor than slag composition in determining the (Mn)/(MnO) ratio. These results will also be published in the near future. It can be seen, therefore, that the results of this paper cannot be applied directly to openhearth studies without a degree of flexibility. J. Chipman (authors' reply)—With regard to the effect of silicon on the manganese constant, this effect is, of course, known. Much more data is needed in order to establish it accurately, and I hope we can look forward to having some accurate data on that. Mr. Hilty suggests that a three-term expression for the Taylor-Chipman solubility of oxygen in liquid iron might fit a little better than the two-term equation. I think that it would be too great a compliment to the precision of the data to employ a three-term equation, and I would still recommend the simple, two-term expression.

Jan 1, 1951

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.1 Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period 0f approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. Vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the system could be degassed thoroughly in

Jan 1, 1948

By Aloys H. Wohlrab

THE conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8 -in. steel show that when bit sizes are reduced from I ½ in., I 3/8 in., and I 3/16 in., to I 3/8 in., I ¼ in., and I 1/8 in., respectively, the volume of the hole is 15 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I.826 in., a difference of 0. 2,5I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and I4° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5.6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1942

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950

By L. C. McCabe

This paper is a progress report on a study of the distribution of the banded ingredients (Figs. 1 and 2) in Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screenings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57 whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample. The relative proportions of the banded ingredients in the Herrin (No. 6) coal in Illinois is reasonably well known but detailed information

Jan 1, 1936

By L. C. McCabe

This paper is a progress report on a study of the distribution of the banded ingredients (Figs. 1 and 2) in Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screenings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57 whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample. The relative proportions of the banded ingredients in the Herrin (No. 6) coal in Illinois is reasonably well known but detailed information

Jan 1, 1936

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary&apos; A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit&apos; An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary&apos; A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit&apos; An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By F. Julius Fohs

Centrally located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis, because it and others of its immediate group exhibit the conditions characteristic of all. I. The Memphis MiNe. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of .the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of about 850 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the hills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen. A line of .crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar—some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to the leaching of limestone and calcite, and the minute ones to the leaching of zinc-hlende.

Jan 1, 1910

By Minoru Yamada, Eikichi Mohri

INTRODUCTION Most of the copper concentrates treated by the flash smelting furnace at Kosaka smelter come from "black ore" that is produced in the local mines nearby. The copper concentrates contain various impurities such as lead and zinc as shown below. [ ] These impurities are mainly concentrated into the flue dusts in the copper smelting system. The dust production rates of flash smelting furnace and converter at Kosaka smelter are, therefore, fairly high compared with other copper smelters. However, by recovering these valuable metals in the dusts systematically, profit-increase of the by-products must be expected. This also leads to the solution of environmental pollution problems and enables us to establish the technical completion of complex sulfide ore treatment by flash smelting process. HISTORY OF DUST TWATMENT AT KOSAKA SMELTER 1) December in 1967 to January in&apos; 1969 Since the flash smelting furnace started its operation in December 1967, all the dusts from the furnace had been recycled. Only conver-

Jan 1, 1976

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.&apos; On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.&apos; In this paper the terms "size broadening" and "strain broadening&apos;&apos; are used in the general sense adopted by warren.&apos; In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957

By J. T. Pardee

INTRODUCTION PLACER is a Spanish word, the definitions of which include "an extensive bank of sand or gravel" and "a place where currents of water deposit particles of gold."l The term, probably first used in the western hemisphere by Spanish or Mexican gold miners, is now generally applied to all detrital deposits that yield valuable minerals by washing. In the Western States placer products other than gold, including the silver alloyed with it, are chiefly sapphires, produced in Montana, and platinum alloys recovered in California and Oregon. During the war tungsten ore (scheelite) was obtained from placers in the Atolia district, California, and a number of diamonds have been found in the Sierra Nevada gold belt. Small amounts of stream tin have been produced in the Black Hills of South Dakota and a little monazite sand in the Boise Basin. Idaho. Magnetite, chromite, ilmenite, zircon, and other useful minerals are more or less abundant in the beach placers of the Pacific coast and in the heavy residues of placer mining elsewhere, but the problems of profitably separating and marketing them remain to be solved. Minerals of lead, quicksilver and other metals occur in many of the placers and although not plentiful enough as a rule to be worth recover-ng, their presence has, in several instances, led to the discovery of valuable lodes, notably at Leadville, Colorado. Historical summary.-In New Mesico, Arizona, and Southern California, placer gold was mined by Mexicans and Spanish priests in the first half of the 19th century or earlier. With these exceptions history of placer mining in the Western States begins with Marshall&apos;s discovery of gold in northern California in 1848. During the next twenty years placers were found in all of the principal mining districts that are known today. The richer deposits were soon mined out but a relatively large production was maintained from the leaner deposits chiefly by hydraulic

Jan 1, 1933

By Francis T. Freeland

The deeper workings of the Leadville mines show refractory ores, consisting principally of sulphides of iron, lead, and zinc, carrying silver, in place of the easily reduced carbonate ores lying nearer the surface. The largest and most extensively developed deposit is that of South Iron Hill.* It lies on the north side of California Gulch,

Jan 1, 1886