Search Documents

By David T. Peterson

Calcium metal was found to deoxidize thorizcm at 1000° to 1200° C. The reaction kinetics were determilled and related to the diffusion coefficients of oxygen in thorium. The solubility of oxygen in thorium, the minimum oxygen concentration, and the diffusion coefficient were determined from 1000° to 1200°C. This firocess results in the lowest oxygen concentrations zohich have been reported for thorium metal. FOR many years it has been known that calcium metal will reduce thorium oxide to thorium metal. This reaction has been the basis for several methods of preparing thorium metal. From the equations giv-by Kubaschewski and vans, ' AF" for the reaction Cao, + Tho,(,) - CaO(,, + Th(,) was calculated and found to be -3.4 kcal at 1000°C, -2.5 kcal at llOO°C, and -2.0 kcal at 1200°c. Thorium is very slightly soluble in liquid calcium, and the solubility of calcium in solid thorium is very low. Consequently these metals would be in essentially their reference states. If thorium containing oxygen were equilibrated with liquid calcium between 1000° and 1200°C, the oxygen content of the thorium would have to be below the solubility limit in thorium. Oxygen is one of the impurities most difficult to remove from thorium and is the most abundant impurity in metal prepared by almost all known methods. Fortunately, oxygen does not have a large influence on the properties of thorium because the solubility in solid thorium is very low. EvenT in thorium containing 100 ppm of 0, particles of thorium oxide can be observed in the microstructure. In view of the incompatibility of thorium oxide and liquid calcium and the low solubility of thorium oxide in thorium, the deoxidation of thorium by this method was investigated. For thorium containing an amount of oxygen well in excess of the solubility limit, the reaction should proceed in the following sequence. The oxygen content of the thorium matrix near the surface would be depleted by the diffusion of oxygen to the surface. At the surface, the oxygen would react with calcium to form calcium oxide. To maintain equilibrium within the thorium, thorium oxide would dissolve to keep the matrix saturated. Consequently, the thorium-oxide particles would disappear first at the surface and then the particle-free rim would grow in thickness. If the rate-controlling step were the diffusion of oxygen through this layer of thorium which was growing in thickness in direct proportion to the amount of oxygen removed, the well known parabolic time law should be observed. If the oxygen concentration at the surface of the thorium and at the inner surface of the deoxidized rim were known, the diffusion coefficient of oxygen in thorium could be calculated from the parabolic rate constant. EXPERIMENTAL PROCEDURE The thorium metal used in this study was prepared by calcium reduction of ThF, by the method described by Wilhelm.' The analysis of this metal is given in Table I. The carbon was determined by combustion, the oxygen by the HC1-insoluble residue method, nitrogen by the Kjeldahl method, and the other elements by emission spectroscopy. A section of this ingot was hot rolled at 600°C to 1/4 and 1/8-in. thick plates. Specimens approximately 7/8 in. square were cut from these plates, and all surfaces of the specimens were cleaned and smoothed by filing with a clean file. Individual specimens were placed in 1-in. diam by 2-in.-long tantalum capsules. Approximately 1 g of clean, high-purity calcium was placed in the capsules and an end closure arc-welded in place. The tantalum capsules were sealed in Inconel crucibles to protect the reactive metals from oxidation. The entire loading procedure was done in a glove box filled with pure argon. The loaded crucibles were placed in a muffle furnace, controlled within 2OC of the desired temperature, for a measured length of time. After the specimen had cooled to room temperature, it was sectioned perpendicular to the large faces and through the mid-point of two of the sides. The sectioned specimen was mounted and polished through Linde A abrasive. The rim which was free of thorium-oxide particles could be clearly observed microscopically as mechanically polished. Twenty measurements of the thickness of the rim were made at equally spaced points far enough from the end of the

Jan 1, 1962

By C. J. Sparks, J. C. Ogle, E. A. Starke

DEFORMATION of cold-rolled fcc metals and alloys produces one or the other of two types of rolling textures, usually referred to as the copper type or the brass type. The pure fcc metals, with the exception of silver, develop the copper-type texture when rolled at room temperature. Silver, brass, and many other alloys develop the brass-type texture. Transition from one texture type to another can also occur. Solute additions to pure copper cause a transition from the copper-type to the brass-type texture.' Varying the deformation temperature also produces texture transitions. Copper rolled at -196°C developed the brass-type texture2 and silver rolled at elevated temperatures, 200°C, developed the copper-type texture.374 The work of Haessner,' Smallman and Green,6 and Hu and coworkers3'4 seems to have established an apparent correlation between the type of rolling texture (and the texture transition) and the stacking-fault probability. Thus materials with low stacking-fault energies are thought to develop the brass-type texture while high stacking-fault energy materials develop the copper-type texture. Mikkola and cohen7 measured by X-ray diffraction techniques the stacking-fault probability, a, in the ordered and disordered fcc alloy Cu3Au. Unexpectedly, ordered specimens showed about twice the stacking-fault probability as the disordered ones. Marcinkowski and Zwe118 also found stacking faults in ordered Cu,Au, but not in the disordered CusAu. More recently, Camanzi and coworkers9 have shown that the intrinsic stacking-fault energy of Cu3Au undergoes a considerable decrease (approximately 100 ergs per sq cm) when passing from the disordered to the ordered phase. In general, deformation reduces order'' but some of our measurements showed that some long-range order still remains in Cu3Au after cold reduction by rolling 80 pct. From the above considerations Cu3Au offers the possibility of studying the texture transition in fcc alloys without varying either the temperature or the composition. If the stacking-fault energy correlation is correct, an initially ordered alloy should develop the brass-type texture during rolling while a disordered alloy should develop the copper-type texture. The present communication describes some initial results of experiments designed to investigate this possibility. The rolling textures of ordered and disordered Cu3Au samples were determined after various amounts of deformation. The ordered sample had an initial long-range-order parameter of S = 1, determined from X-ray diffraction. The grain size of both the ordered and disordered samples was the same, and the initial textures of both were also identical and approximately random. No obvious differences in the deformation textures of the ordered and disordered materials were detected up to 35 pct reduction and the (111) pole figures of Fig. 1 resemble that of pure copper. However, with reduction larger than 35 pct and less than 50 pct, a marked deviation from the copper texture was noted in the ordered material. The newly developed orientation was close to the (110)[i12] ideal orientations re-

Jan 1, 1970

By John R. Hutchins

1ms is a report of nickel (wire) oxidation studies designed to test the validity of Valensi's1 equation developed for the kinetics of a reaction controlled by diffusion in a continuously growing product layer on cylindrical surfaces. The equation is:

Jan 1, 1968

I AM sure you know that it is necessary to draw the gold into wire in order to make gold cloth, gold embroidery, or gold filigree work. Just as it is beaten to form leaf for ornamenting pictures, so also can gold be drawn easily. The same is done with silver and tin, and I believe it could also be done with iron, copper, and brass. Although brass is not so

Jan 1, 1942

By Wheeler Davey

WHEN metals are subjected to mechanical working, such as rolling, one of the phenomena that take place is a movement of the crystals of the metal into a system or systems of orientation which bear an angular relation to the direction of working. In rolled metal the crystals may orient themselves with respect to the rolling plane or the rolling direction, or both. Direct evidence of the existence of preferred orientations in rolled metal has been obtained by numerous investigators from X-ray patterns of the rolled metal. Most of these workers used a monochromatic pinhole method. Where the degree of preference for a single orientation is high the monochromatic pinhole pattern may be interpreted by a geometrical calculation based on the angular relationships of the planes in the crystal and the diffraction arcs on the X-ray pattern. This process may be aided by the geometrical construction of the locus sphere (Langenkugel), and reflection circles of Polanyi,1 Polanyi and Weissenberg,2 and Mark and Weissenberg,3 and of the plane polar figures (flachenpolfigur) of Franz Wever.4 R. M. Bozorth5 solves X-ray patterns from metals having a single preferred orientation by means of a series of charts which when placed over the X-ray pattern give directly certain angular relationships, between the crystal planes and the surface of the specimen.

Jan 1, 1929

By Elton A. Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11. mile bus ride up Railroad Creek to Holden. A11 freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting. Ore is broken by long-hole blasting using the Noranda system which has been modified to meet local conditions. Until recently, blastholes have been drilled by diamond drills. Now a partial substitution of percussion drill holes, drilled with tungsten carbide insert bits, is being made. Geology The ore body occurs as a replacement deposit in a highly metamorphosed series of sedimentary rocks, mainly gneiss and schists, in a shear zone several hundred feet in width and of undetermined length. Commercial ore has been found in mineable widths of 25 to 100 ft for approximately 2500 ft along its strike. The commercial minerals are chalcopyrite, sphalerite, and gold. During the period of mineralization considerable silicifica-tion took place giving the ore an abrasive drilling characteristic. Following the period of mineralization, numerous dikes were introduced into the ore body. The earlier ones were of granite composition having a width of a few inches up to 80 ft. These were followed by much younger, fine grained basic dikes which usually do not exceed 2 ft in width. Development of Percussion Blasthole Drilling Equipment Test work with the 1½-in. tungsten carbide bit was carried on in development headings for several months early in 1947. The short life of the bits, because of gauge loss caused by the abrasive nature of the rock, prevented its adoption for this use. However fast drilling speed and ability to drill a long uniform hole suggested its use for drilling blastholes in competition with diamond drills as diamond costs were steadily increasing and exper-ienced drillers were difficult to obtain. The 1½-in. bit was the largest available at the time initial test work was started with sectional steel. The 1½-in. hole limited the diameter of the steel thread and coupling which could be used. Type F couplings were first used but because of the small thread section excessive breakage of the steel was experienced. Type H couplings were tried next. In order to use this coupling which is 15/8 in. in outside diameter, it was reduced to 1 3/8 in. giving 1/8 in. clearance between the coupling and the hole. Rod breakage at the thread was substantially reduced but some coupling breakage was experienced, however the overall performance was considered satisfactory (see Fig 1 for illustration of coupling and thread). Early test work with the 1½ in. bit indicated machines of piston diameters larger than 255 in. would cause inserts to loosen or break. It was found however that the additional weight of the sectional steel cushioned the blow enough to prevent bit failures when 3-in. Leyners were used. Rods used with the 1½-in. bits were 7/8 in. q. o. for sectional steel and 1 in. q. o. for all chuck pieces. In May 1948, 2-in. tungsten carbide bits became available and test work was immediately started. The 2-in. hole approximated the AX (1 15/16 in.) diamond drill hole which was being used exclusively for blastholes and permitted their substitution for diamond drill holes in a ring without alteration of pattern, burden, or explosives. The 2-in. bit also gave room in the hole for larger couplings and permitted the use of heavier rods and 3½-in. machines, increasing the

Jan 1, 1950

By P. Somasundaran, R. D. Kulkarni

Reagentizing at elevated temperature, reported in the past as beneficial for the flotation of hematite using oleate, is studied here as a function of collector concentration, solution pH and ionic strength at various levels of conditioning temperature. The study revealed strong interactions between variables; particularly, the effect of conditioning temperature was found to strongly depend on the ionic strength of the solution. Thus, while an increase of conditioning temperature at lower ionic strengths or that of ionic strength at lower temperatures resulted in an increase of both flotation and grade, an increase of the former at higher ionic strength or that of the latter at higher temperatures caused a significant decrease in both responses. These observations have been explained in terms of the increased chemisorption of oleate at elevated temperatures and the temperature effect of ionic-strength on the salting out of the oleate from the bulk solution. The above effects which were first observed during Hallimond cell flotation tests were subsequently tested with Denver cell using low-grade iron ore. The results obtained using the two test procedures were in agreement with each other. The implications of these effects and interactions for process control of optimum flotation performance must be noted since variation in the levels of the above parameters are likely under plant conditions.

Jan 1, 1978

By William H. Kobbé

The word recovery as used in this paper is applied in its broader sense and not limited to wells producing from horizons of unconsolidated sands. Certain problems connected with the winning of petroleum from such horizons present themselves while drilling is in progress and should be considered before drilling is commenced wherever unconsolidated sands are expected. Maximum recovery depends not alone. upon efficient pumping methods but also upon the selection of a proper drilling system and the completion of a well especially adapted to the extraction of these oil-bearing sands. 11. DRILLING Determining Factors in Selection of Method The selection of a drilling method for the development of a region in which the oil reservoir consists of unconsolidated sands is based on the following considerations: (1) Character of the formations overlying the reservoir; (2) thickness of the oil-bearing stratum or strata; (3) thickness and character of water or gas sands; (4) gas pressure to be encountered or expected; (5) total depth of well. 1. Character of the Formations Overlying the Reservoir The strata overlying the reservoir may consist of beds of shales, clays, sands and other soft materials, or they may be slates, limestones and sandstones consolidated to all degrees of hardness. Very often the overlying strata are predominantly of soft materials but interbedded with harder formations. Likewise, soft strata are encountered at different horizons in an overburden consisting almost entirely of the harder sedimentaries. The physical character of this overburden is frequently

Jan 1, 1917

By F. M. Smith, R. H. Moore, J. R. Morrey

Electrodiffusion in y cerium reported by Henrie has been confirmed and a Preliminary estimate made of the relative rates of electrodiffusion of iron, cobalt, and nickel. These diffuse to the anode at rates decreasing in that order. In addition, copper and manganese exhibit slow, but detectable, diffusion to the anode and molybdenum exhibits detectable diffusion to the cathode. The electrodiffusion of carbon, .zirconium, antimony, magnesium , and silicon in y cerium could not be detected. Iron and cobalt diffuse in y cerium at rates proportional to the current density and with no apparent dependence on temperature. Decreasing polarization of iron and cobalt with increasing temperature, which cancels the expected rate increase, would account for this behavior. The electrodiffusion rate of iron in y uranium and in E plutonium has been measured. Diffusion of iron is anode-directed. Tin was found to diffuse to the cathode, in y uranium, at an appreciable rate. In all of these solvent metals, negative ions diffuse to the anode and positive ions to the cathode. The potential field effect appears to account satisfactorily for these results. FROM early experimental work summarized by Jost1 and Seith,2 the driving force for electrodiffusion was attributed to the potential field acting on ions in a metal. More recently, Heuman,3 Wever,4 and Huntington5 have shown that momentum interchange between conduction electrons and mobile entities in the metal contributes to electrodiffusion. Electron momentum interchange is anodically directed and the direction of diffusion resulting from the field force is dependent upon the charge on the diffusing entity. These two effects may either reinforce or oppose each other. Glinchuk6 has pointed out that momentum transfer in defect conductors should be cathode-directed and this appears to be the case as demonstrated by wever's4 work on iron. Barnett's7 work, on the other hand, indicates that, even in defect conductors, electrons show a negative E/m ratio when accelerated with respect to the lattice and should lead to anode-directed momentum transfer. In discussing this problem, Wever and seith8 suggest that defect electrons interact preferentially with activated ions so as to allow a net movement toward the cathode while still maintaining an electron momentum transfer in the anode direction. Williams and Huffine9 and Henriel0 have demonstrated that electrodiffusion may be useful for purification of yttrium and cerium. In yttrium, Williams and Huffine note that movement of several metallic impurities toward the anode is in keeping with observations in most other metallic systems and indicates that yttrium remains a normal electronic conductor at least to 1230°C. Close inspection of their data shows, however, that oxygen, nitrogen, and the transition elements diffused toward the anode, while nontransition elements diffused toward the cathode. This suggests that potential field effects may have been appreciable. The present work was concerned with the applicability of electrodiffusion as a technique for purification of plutonium, but, because of the obvious hazard inherent in work with this metal, experiments to develop the technique were carried out using cerium and uranium. The results of electrodiffusion measurements on these metals and on plutonium are reported here. EXPERIMENTAL The metal specimens prepared for this work were 6 in. long, 1/4 to 1/2 in. wide, and 1/16 to 3/32 in. thick. The uranium specimens were machined from a bar which analyzed 310 ppm Fe and the electrodiffusion of iron was followed by spectrographic and by chemical analysis. Cerium and plutonium specimens were cut from sheet rolled from ingots obtained from molten salt-metal equilibrations during which radioactive tracers were introduced. The electrodiffusion of the tracers was subsequently determined by counting methods. The specimens were electrolyzed between nickel electrodes containing resistance heaters used to equalize the specimen and electrode temperatures, thereby reducing thermal gradients. The temperature of the electrodes adjacent to the ends of the specimen was measured with chromel-alumel thermocouples which were connected to the heater controls. The surface temperature of the specimen at a point midway between the electrodes was measured with a sapphire rod pyrometer, the output of which controlled the dc power supply. This assembly was enclosed within an evacuable chamber containing a quartz viewing window. The temperature of the specimen over its entire length could be scanned with a portable pyrometer through

Jan 1, 1965

By R. C. Buehl, M. B. Royer

A three ton per day blast furnace using blast temperatures up to 2200°F was operated to recover manganese from open-hearth slag and manganiferous iron ore. The spiegel product containing 12 to 24 pct Mn was blown in a basic converter to high manganese oxide slag as described in the paper which follows this one. HE steel industry, which uses over 900,000 short tons of contained manganese yearly, depends on the maintenance of supplies of manganese from foreign sources such as India, Gold Coast, and Union of South Africa. Domestic ores furnish less than 10 pct of the yearly requirements of metallurgical ores and, unfortunately, the United States has no large, or even moderate, grade deposits that could supply a major portion of the requirements for many years. It may be necessary to obtain manganese from low grade materials, even though the cost is appreciably higher than when imported ores are used. An American Iron and Steel Institute questionnaire prepared in 1949 revealed the startling fact that open-hearth slags contained about as much manganese as is imported annually. The quantity of slag produced each year by integrated steel plants (not including cold-melt shops) and the manganese contained in the slag follows: Flush slag, 4,500,000 net tons a year containing 408,000 net tons Mn; tap slag, 7,230,000 net tons a year containing 364,000 net tons Mn; for a total of 772,000 net tons Mn. Some of this slag is returned to blast furnaces but about 75 pct would be available for the recovery of manganese. In several decades, when many of the present sources of high manganese ores have been depleted, open-hearth slag and manganiferous iron ore may become the major source of the manganese required for steel production. In 1948, manganese-ore imports from the U.S.S.R. were 427,000 net tons or 34 pct of the foreign ore. Imports from this source were only 81,000 tons in 1949. It became evident that adequate stockpiles of manganese could not be accumulated for many years. The Bureau of Mines initiated an extensive research program on methods for increasing domestic production of manganese and entered into a cooperative agreement with the American Iron and Steel Institute for recovering manganese from open-hearth slags whereby the Institute provided additional research funds and trained operating personnel. Description of Process and Equipment Numerous pyrometallurgical and hydrometallur-gical processes and combinations of the two can be applied to the recovery of manganese from open-hearth slag and manganiferous iron ore. The process being developed at the Pittsburgh Station of the Bureau of Mines consists of: 1—Reduction of open-hearth slag in a blast furnace to recover the iron and manganese as spiegel-eisen with 12 to 24 pct Mn. 2—Selective oxidation of the manganese from the blast-furnace metal in a basic-lined converter to produce a high manganese slag with up to 60 pct Mn content, which is a synthetic ore for the production of ferromanganese. This process has the advantage over other processes in that the equipment which would be used, such as blast furnaces and converters, has been highly

Jan 1, 1953

By R. W. Carpenter, J. C. Ogle

It is possible, by using pack-rolling instead of conventional rolling, to reduce a number of metals to thicknesses of 2µm or less. Such thinfoils are generally made at room temperature without intermediate annealing. In addition, pack-rolled foils fail by developing pinholes at thicknesses near 2µm instead of developing the shear cracks usually observed in cold-rolled ductile metals. This paper presents the results of a general investigation of the deformation substructure and texture developed in copper and iron pack -rolled from 130 to about 2µm thickness. Electron microscopy showed that in both metals a fine (0.2 to 0.5?µ m) deformation subgrain structure formed during pack-rolling; in neither case was this substructure grossly different from substructures formed during conventional rolling. The deformation texture formed in pack-rolled iron was quite similar to usual bcc textures; however, in the case of copper, the cube texture was stable during pack-rolling and the normal copper deformation texture was unstable. It is shown analytically that the constraining pack induced a large hydrostatic pressure in the foils during pack-rolling. The pinhole failure mechanism is attributed to the presence of the large hydrostatic pressure during pack-rolling; this strongly suppressed the growth of shear cracks. The stability of the cube texture in copper is also probably due to the unusuul stress distribution developed during pack-rolling. EXPERIMENTS at several laboratories have shown that very thin foils of the common structural metals and many of the rare earths can be made by "pack-rolling". 1-3 The technique was originally developed to make specimens for nuclear scattering experiments and foils for X-ray filters. It is also useful for making experimental laminar metallic composite bodies and foils thin enough for direct examination by ultra-high voltage electron microscopy without the need for special thinning techniques. Pack-rolling in the present context means a three-layer pack, with the material to be rolled into foil comprising the center layer. The outer two layers, which constrain the foil during reduction, are ordinarily austenitic stainless steel. Typically, a 130 µm (0.005 in.) metal strip can be reduced to a final thickness of 2 µm or less by this process. This is accomplished at room temperature, without intermediate annealing. It has been observed that foils produced by this process do not exhibit at any stage of their reduction the severe work-hardening found in strip rolled by conventional cold-rolling methods. Neither is the failure characteristic the same."&apos; Conventionally cold-rolled ductile metal strip fails by developing shear cracks on planes whose normals nearly bisect the angle between the rolling direction and normal to the rolling plane; these are planes of maximum shear stress. In pack-rolling this mechanism has not been observed; failure occurs by the formation of pinholes on the foil surface (penetrating the foil). If pack-rolling is continued the hole density increases. These differences in behavior imply the existence of appreciably different substructure in pack-rolled foils compared to substructure in conventionally rolled material, or perhaps that the geometry of pack-rolling has an effect on the foil behavior. This paper describes an investigation of deformation substructure and texture in some specimens of pack-rolled copper and iron, and some considerations of the stress distribution in the foils during rolling that result from the geometry of pack-rolling. EXPERIMENTAL DETAILS Three different materials were used for pack-rolling in the present work: soft copper sheet (99.8 pct Cu, 0.03 pct 0, electrolytic tough pitch) and two types of iron, Ferrovac E* and Armco iron. Each was "Crucible Stccl Co. initially in the form of 130 µm annealed strip with grain size ranges of approximately 10 to 40 µm. The initial texture of the copper (determined as noted below) was the normally observed cube type (001)[100]; there was evidence of a small amount of material in the cube-twin orientation reported by Beck and Hu.4 The initial texture of the Ferrovac E was similar to that reported for recrystallized iron by Kurdjumov and sachs,5 who list the principal orientations as {111}<112>, {001}<110> 15degfrom RD and a weak component {112}(110) 15 deg from RD. The starting texture of the Armco iron was not determined. Pack-Rolling Procedure. A four-high mill was used for all specimens. The work roll and backing roll diameters were 1.625 and 5.25 in., respectively. The peripheral roll speed of the work rolls was about 2.5 in. per sec. All foils were initially reduced from 130 to 100 µm by conventional straight rolling and then inserted into a pack, without any intermediate annealing, for further reduction. The pack consisted of an 0.033 in. (838 µm) thick 3 by 6 in. polished sheet of austenitic stainless steel, folded to make a 3 by 3 in. jacket. After folding, the jacket was given a small reduction to close the fold tightly before insertion of the foil. During pack-rolling a constant change in roll spacing was made every third pass. The roll-spacing change corresponded to a 5 pct reduction in thickness for a new pack. This approached a 10 pct reduction when the pack had decreased to about half its original thickness. At this point the deformed pack was discarded and a new one

Jan 1, 1970

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metaliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land the surface of which is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar " method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years .ago, has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are equally applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral, owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1927

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar" method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is -no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for: agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar" method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will&apos; be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar " method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By R. Maddin

IN analyzing the relation between the orientation of new grains and that of the deformed matrix of axially extended and recrystallized single crystals of face-centered cubic metals, a two-stage rotation process" is generally used where the first rotation is made in order to account for an "adjustment of orientation to the environment of strain."&apos; It has been argued that in spite of the difference of orientation, which may amount to as much as 12" (in a brass),&apos; between the octahedral plane as observed in the parent lattice and in the recrystallized grain, it is believed to be a common plane in the sense that it constituted the nucleus in the parent strained crystal from which the new grain grew.&apos; A possible source of the deviation in orientations of a common pole in the new grain and that of the deformed single crystal matrix from which it has grown may be found in the distribution of strain resulting from the plastic deformation. It might be expected in view of the incongruent nature of shear&apos; that the perfection of the octahedral plane along which glide has occurred is disrupted and that this disruption constitutes the strain from which nuclei of new grains can grow during recrystallization. Evidence for the existence of strain along glide planes was first detected by Taylor" in 1927 and substantiated by Collins and Mathewson&apos; in 1940. In their investigations, however, the deformed single crystalline specimens (aluminum) were cut mechanically along the glide planes followed by mechanical polishing. X-ray exposures (glancing angle) of only 8 min with filtered radiation were used. It was later shown&apos; that this type of surface preparation did not remove with all certainty the mechanically disturbed surface. It was felt that a re-investigation of this phenomenon using more refined techniques might reveal a more correct extent of the strain resulting from the deformation which might correlate the deviation of the common pole of the recrystallized grain with the acting slip plane of the matrix crystal. In accordance with these thoughts, a single crystal of a brass (70/30 nominal composition) M in. in diam x 5 in. long, tapered as in previous experiments,&apos; was extended and carefully documented with respect to elongation and shear. Disks about % in. thick paralle&apos;l to the primary slip planes were cut from the specimen by means of an etch cutter." These disks represented volumes of the specimen which had been extended 0, 5, 10, 15, and 20 pct. Copper Ka monochromatic radiation was obtained by reflecting 35,000 v copper radiation from the c-cleavage face of a pentaerythritol crystal. The monochromatic radiation was collimated and led on to the disk set at the proper 0 angle for reflection from the primary (111) planes. The monochromatic beam was aligned in a plane containing the active slip direction. Following a 10 hr exposure at the theoretical Bragg angle, the disk was reset at 0 + 1°, 0 — 1", 0 + 2", 0 — 2", etc., until no Bragg reflection was obtained. The disk was then rotated 90" about its polar axis, and the same X-ray procedure was used. The results are shown in Table I. It may be seen from the results in Table I that the plastic deformation (20 pct elongation) produces fragments of the glide plane which are rotated or tilted as much as 25 " from the normal position on a purely block slip model. In addition to the large variation in 0 angle in the slip direction, there is a variation in 0 as much as 20" in the direction at right angles to the direction of slip, i.e., <110>. In view of the results shown, it may now be argued that the strain distribution finds its origin in the incongruent nature of the slip process.&apos; The use of the two-stage rotation process seems valid in attempting to explain the relation between the orientation of recrystallized grains and the matrix from which they have grown. Acknowledgment This work was sponsored by the ONR under Contract Number N6 onr 234-21 ONR 031-383. The author would like to thank N. K. Chen for reading and correcting the manuscript. References &apos;R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins. Trans. AIME (1949) 185, p. 655; Journal of Metals (September 1949). &apos;J. A. Collins and C. H. Mathewson: Plastic Deformation and Recrystallization of Aluminum Single Crystals. Trans. AIME (1940) 137, p. 150. eN. K. Chen and C. H. Mathewson: Recrystallization of Aluminum Single Crystals After Plastic Extension. Unpublished. 4 C. H. Mathewson: Structural Premises of Strain Hardening and Recrystallization. Trans. A.S.M. (1944) 38. :&apos;C. H. Mathewson: Critical Shear Stress and Incongruent Shear in Plastic Deformation. Trans. Conn. Acad. of Arts and Science, (1951) 38, p. 213. "G. I. Taylor: Resistance to Shear in Metal Crystals, Cohesion and Related Problems. Faraday Soc. (1927) 121. &apos;R. Maddin and W. R. Hibbard, Jr.: Some Observations in the Structure of Alpha Brass After Cutting and Polishing. Trans. AIME (1949) 185, p. 700; Journal of Metals (October 1949). &apos;R. Maddin and W. R. Asher: Apparatus for Cutting Metals Strain-Free. Review of Scientific Instruments (1950) 21, p. 881.

Jan 1, 1953

By R. D. Stover, F. O. Shuck

The variation of binary-diffusion coefficients with composition in the liquid Bi-Sn system at 300°C was measured using the capillary-reservoir technique. The experimental coefficients did not exhibit a simple composition dependence. A number of tests were also made to determine the effect of variation of density with composition on convection within the capillaries. These tests indicate that the density changes arising from composition duferences may give rise to high diffusion coefficients unless care is taken to maintain a stable configuration. In recent years there has been considerable interest in diffusion in liquid metals. However, the bulk of the work done to date has involved measurements of self-diffusion or diffusion of dilute concentrations of "solute" metals. Because there are possible applications to liquid phase processing of metal alloys and since additional data may help to clarify the nature of diffusion in liquid metals, investigations of the concentration variation of diffusion coefficients in binary alloys have been undertaken. Of past studies only two have covered large ranges of binary composition. Niwa et al.&apos; investigated the Pb-Sn, Bi-Pb, and Bi-Sn systems and Grace and Derge2 investigated the Bi-Pb system. Because of the discrepancy between the data of these investigators, it was deemed desirable to check the possibility of convection arising from the variation of density with composition. The capillary-reservoir technique of Anderson and saddington3 was chosen for the present investigation since it has been widely used for measurements involving dilute solute concentrations and it was the technique used by Grace and Derge.2 It was necessary, however, to modify the normal procedure of using a pure metal bath to avoid measurement of integral diffusion coefficients over large concentration ranges. The alloy system chosen for study was the Bi-Sn system for which there are some data available.&apos; EXPERIMENTAL PROCEDURE In order to utilize the capillary-reservoir technique for measurements of diffusion coefficients as a function of composition, it was necessary to modify the normal procedure slightly. This modification consisted of using a reservoir composition which was only slightly different from that in the set of capillaries, in order that the integral coefficients measured might be taken over a small composition range and might thereby be assumed to approximate the differential coefficient at some average composition between that of the capillary and that of the bath. It was found that a composition difference of approximately 0.10 mass fraction provided a satisfactory compromise between a small increment in composition and reasonable accuracy in measuring changes of composition. The alloys were prepared from tin and bismuth of 99.999 pct purity. The materials were first cleaned of surface oxides, then weighed and melted to form a homogeneous alloy in a Pyrex filling apparatus. The capillaries used were of precision bore Pyrex tubing 1.000 *0.005 mm bore. Capillaries of various lengths (from 2.85 to 5.85 cm) were cut and sealed at one end by fusing a 3-mm Pyrex rod to the end. The capillaries were filled by inserting them into the filling chamber, evacuating the chamber, submerging the capillaries, and pressurizing the chamber with argon. Two sets of capillaries were prepared for each run. One set contained an alloy more dense than the bath alloy and one set a less dense alloy. This procedure was followed so that the effect of density difference on the measurement could be determined. After filling one set of capillaries, these were placed open end up in a capillary holder and transferred to the diffusion chamber which consisted of a Pyrex tube inserted into a graphite block. The second set of capillaries was then filled and placed into the diffusion chamber. The reservoir alloy, which had been melted in a separate crucible, then was poured carefully into the diffusion chamber. Sufficient reservoir alloy was used to cover all capillaries to a depth of several centimeters. All of these operations: capillary filling, melting of alloys, and diffusion anneal, were carried out in a fused-salt bath which maintained a temperature of 300"*1°C. All capillaries were permitted to diffuse for approximately 48 hr. At the end of the diffusion period the capillary holder was removed from the bath and

Jan 1, 1969

By T. M Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the &apos;active masses&apos; of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-&apos; that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By T. M. Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the &apos;active masses&apos; of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-&apos; that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy&apos;s law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy&apos;s law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy&apos;s law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933