Search Documents

By H. F. Ameen, F. M. Hamilton

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By J. L. Zakin, G. K. Patterson, J. M. Rodriguez

Correlation has been obtained between drag-reducing characteristics for turbulent flow in a pipe and measurable properties of several polymer solutions. Several concentrations of high molecular weight polymethyl methacrylate in toluene, high molecular weight polyisobutylene in both toluene and cyclohexane, medium molecular weight polyisobutylene in cyclohexane and benzene and low molecular weight polystyrene in toluene were studied. Data obtained in these nonpolar solvents and literature data for more polar solvents were successfully correlated as the ratio of measured friction factor to purely viscous friction factor vs the modified Deborah number vrl/D0.2 where 71 is the first-mode relaxation time of the solution estimated by the Zimm theory. A shift factor which is a function of intrinsic viscosity 1/(4[?] - 1) allowed all the data obtained with nonpolar solvents to be correlated as a single function. For these systems, most of the data fit a single curve to within + 5 percent of the average friction factor ratio. The shift factor did not give a unique function of the data for the more polar systems. INTRODUCTION The phenomenon of drag reduction in polymer solutions was first studied by Toms1 in dilute solutions of polymethyl methacrylate in mono-chlorobenzene. The drag ratio for flow through circular tubes has been defined2 as the ratio of the pressure. drop of the solution to the pressure drop of the solvent at the same flow rate. The drag ratio is less than 1.0 for a drag-reducing fluid. Practical use of drag reduction is being made in fracturing operations in the petroleum industry.3 A more fundamental quantity is the friction factor ratio, defined as the ratio of the observed pressure drop to that predicted for a solution of the same viscosity characteristics and density at equal flow rates using the Dodge-Metzner friction factor equation4 Viscous solutions with drag ratios greater than 1.0 can have friction factor ratios less than 1.0. For practical applications, it is drag reduction which is of interest. However, for correlation the fundamental ratio is the friction factor ratio. In recent years, drag reduction has been studied extensively. Recent studies have shown that reasonable predictions of the incipience of drag reduction in polymer solutions can be made from the properties of the solutions and the flow Variables.5 However, it has not been possible to predict accurately the amount of drag reduction to be expected for a given polymer solution without any drag-reducing turbulent flow data on the same solution.6 For flow through circular tubes it is well established that there is a concentration effect and a diameter effect on drag reduction. Toms1 observed that drag reduction increases with an increase in the concentration of the solution up to an optimum concentration beyond which, due to the increased viscosity of the solutions, the drag ratio increased with an increase in concentration. Hershey 7 observed that for dilute Newtonian polymer solutions in nonpolar hydrocarbon solvents, a normal transition region may be obtained followed by a departure from the von Karman equation (on a friction factor-generalized Reynolds number chart). The point of departure is a function of diameter: the smaller tubes depart at the lower Reynolds numbers. Concentrated solutions may show no abrupt transition region, but merely an

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By Fred H. Klaer

Water supplies dependent upon induced infiltration can be developed by vertical wells, by infiltration galleries, or by horizontal water collectors. Each method is described and the advantages of water obtained by induced infiltration with respect to cost, chemical quality, and temperature are shown by specific water supplies. THE subject of ground water in industry is assuming increasing importance as new processes and new industries are developed. Industrial specifications of chemical quality and temperature for process water and for cooling purposes are becoming more rigid, and water must now have many properties to meet these requirements. As ground water is usually more constant in quality and temperature, many industries are turning to ground-water supplies to satisfy their growing need. As many published articles have stated during the past several years, the ever increasing demands have caused shortages of water supply in many localities throughout the United States. Although such shortages are generally of a local nature, they have given rise to many attendant problems, such as increased pumping costs, salt water encroachment, and rising ground-water temperatures. One partial solution to the problems of overdevelopment of the ground-water reservoirs in many areas can be accomplished by developing ground-water supplies that are dependent upon induced infiltration and by planning the use of underground reservoirs. These reservoirs can be filled during periods of excess precipitation and stream flow and can be emptied during periods of drought, in a manner similar to the use of surface reservoirs. In this way water that otherwise would be wasted into the oceans is salvaged during periods of excess. The development of water supplies dependent on induced infiltration is a relatively new concept and should be defined. When a well is pumped, the water level around the well is lowered in the shape of an inverted cone or cone of depression. As pumping is continued, the cone of depression will continue to expand, horizontally and vertically, until the quantity of water crossing the perimeter of the cone plus the recharge within the area of the cone is equal to the quantity of water being pumped.

Jan 1, 1954

By George Frederick Kunz

Mexico has been famous for its silver-mines ever since the Spanish conquest; but in respect to gems, although many varieties occur, yet only a few have been obtained in any important amount. Considering the extent of country in Mexico and ill the adjoining States of the Central American Republics, and the richness of mineral wealth that must surely exist there, our present knowledge of the occurrence of precious stones is remarkably small. The great prevalence of igneous rocks would lead us to anticipate the future discovery of many localities of gems and ornamental stones, when fuller scientific exploration shall have taken place.* At the present time the only gem-stone that is systematically mined in Mexico is opal, and the only important ornamental stone is tecali, the so-called Mexican onyx. In addition to these may be mentioned the pink garnet, or rosolite, found in one

Jan 1, 1902

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By W. J. Reagan

IN a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the vari-ous sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In. the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable 'indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2 in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be involved.

Jan 1, 1936

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

A shrinkage stope is an overhand stope in which the broken ore accumulates until the stope is completed to, or near, the level above. As broken ore generally occupies at least 60 per cent. more space than ore in place, about a third of this must be drawn out as the stope advances to leave a working space under the back. The ore remaining supports the miners and gives temporary support to walls, and is all withdrawn when the stope is finished. The shrinkage-stope method is applicable to steep-dipping deposits of strong ore with strong walls. It may be applied to narrow or wide veins, and is simple and cheap. Five examples, which include important and varied types of deposits, are given: namely, Kennecott, Homestake, Jarbidge district, Mogollon district, and Cripple Creek district.

Jan 1, 1925

By Joseph H. Allen

Commercial coke is made to-day in the United States chiefly from the Appalachian, the Illinois and the Colorado coal-fields. The measures of the great Appalachian coal-fields furnish by far the largest proportion, only about 1 per cent. coming from those of Illinois and Colorado. This is not due, however, to a corresponding difference in area. The Illinois field covers about 47,000 square miles in Illinois, Southern Indiana and Western Kentucky. The coal is high in both ash and sulphur, and on this account nearly all the attempts which have been made from time to time to coke it have resulted in failure, so far at least as the requirements of ironmasters are concerned. Nevertheless,. I am able to say from a practical knowledge of this field that the physical structure of the coke is perfect, and

Jan 1, 1893

By Evert Hoek

Summarising a conference is never an easy task, but I will try to keep my comments brief and to the point. There are a number of lessons which we have learned from our deliberations together during these past three days, and I will try to give you my impressions of these lessons and of their practical implications in open pit mining. The first thing that has become increasingly obvious during these discussions is that it is no longer acceptable to offer an 'Act of God' as an excuse for a major slope or tailings dam failure. Disasters such as that at Aberfan in the United Kingdom have focussed the world's attention on the activities of the mining industry and the report of the commission set up to investigate the Aberfan disaster clearly showed that adequate knowledge was available and that failure to apply this knowledge did not qualify as an 'Act of God'. The courts and the world's press are certain to impose increasingly harsher penalties and criticism on those held responsible for major failures, particularly of tailings dams, in the future. One of the major problems in applying available knowledge to slope problems is that attempts to apply this knowledge are frequently left too late. To provide an engineering solution in the case of a slope in an advanced state of failure is an almost impossible task, and it is essential that those responsible for the stability of a slope must learn to recognise signs of distress at an early enough stage for effective remedial measures to be taken. As our ability to solve slope problems improves, the time at which slope stability problems are considered in a mining project must move forward to a stage at which these problems can be anticipated and dealt with before they arise. Conferences such as this are important in that they enable us to exchange ideas and advance our knowledge to a level at which such predictive engineering will be possible. It has been encouraging to hear of mining projects such as the Bougainville Copper operation where slope stability studies were carried out as part of the overall evaluation programme and it is hoped that this will become a more common procedure in the future. Providing a safe slope in an opencast mine obviously costs money, either in terms of the reduced ore to waste ratio given by flat slopes or because of the cost of stabilization techniques such as drainage or the use of rock anchors. An optimum slope design will provide maximum safety at minimum cost but achieving this optimum is not an easy task. Any one of us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make

Jan 1, 1971

By E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, Calif. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, N.Y., was developed by the Cabot Corp. A processing plant was placed on-stream in 1953, with nearly continuous production to date, and it is currently operated by Interpace Corp. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1973, the United States was the major producing country, furnishing about 75% of the world's output. Recent production also has come from Finland, Mexico, and Kenya. Small amounts have been shipped intermittently from India, USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and South-West Africa. The principal use of wollastonite is in the manufacture of ceramics, especially wall and floor tiles. Other uses are for paints, fillers, adhesives, reinforcing agents, plastics, fluxes, and glazes. Mineralogy Pure wollastonite, CaSiO3, has the composi¬tion of 48.3 % CaO and 51.7 % SiO,. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mobs' scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540° C. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both; colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The brightness of wollastonite is a property of considerable importance to the paint industry. Material, 99% pure, with a size of -325 mesh, has a General Electric reflectance rating of 92 to 96%. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature form. Inversion of wollastonite to pseudowollastonite occurs at about 1120° C, resulting in an increase in the coefficient of expansion and a color change. Pure white wollastonite, on inversion, may change to a cream tint, or various shades of red or brown. The color change is thought to be due to the presence of iron and strontium.

Jan 1, 1975

By William E. Ford, Edward Salisbury Dana

This section includes the common calcium titano-silicate, Tiianite; also a number of silicates which contain titanium, but whose relations are not altogether clear; further the titanate, Perovskite, and niobo-titanate, Dysanalyte, which is intermediate between Perovskite and the species Pyrochlore, Micro- lite, Koppite of the following section. In general the part played by titanium in the many silicates in which it enters is more or less uncertain. It is probably in most cases, as shown in the preceding ages, to be taken as replacing the silicon; in others however, it seems to play the part of agaaic element; in schorlomite (p. 510) it may enter) in both relations.

Jan 1, 1922

By R. E. Ford, P. Tarassoff, P. H. Jennings

Copper oxide ore may be leached at all sizes from run-of-mine down to pulp, and consideration must be given to all available methods in determining the most economical one. Heap leaching was evaluated in a pilot plant at Gaspe Copper Mines, Ltd. which was designed to simultaneously leach two 1200-ton dumps of ore. The plant was operated for two years, in part under severe winter conditions. Two modes of leaching were investigated: acid leaching in which sulfuric acid was added externally to the leach solution, and pyritic leaching in which pyrite concentrate was added to the dump and acid was generated in situ by bacterial action. The pilot plant operation is described, and the results are compared with laboratory data obtained in 6-in.-diam columns. It is concluded that pyritic leaching offers certain operating advantages over acid leaching when copper is recovered by cementation in that iron buildup in the solution is prevented.

Jan 1, 1974

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution. Anaconda had done considerable work on the production of sponge iron in 1914 for use as a precipitant of copper from leach solutions. Some success and considerable experilence were attained at the time. indicating that, sponge iron might be successfully made by a modification of the process used in 1914, a batch process in which an iron calcine was reduced by means of soft coke, resulting from noncoking coal, in a Bruckner-type revolving horizontal cylindrical furnace widely used 50 years ago. The coke and calcide formed the bed in the Bruckner furnace, which was rotated at about 1 rpm. The bed was brought to a temperature of about 1800°F by means of an oil flame over the surface. Although results were reasonably satisfactory, they did not warrant full development of the process at that time. A good deal of work has been done in the last 50 years on the production of sponge iron. The objective in some cases has been the production of a precipitant for copper from solution, but the bulk of the work has been done for the production of open-hearth steel furnace stock. The production of an open-hearth stock presents two problems rather than one: first, producticon of the sponge iron, and second, what is perhaps of equal difficulty and importance, conversion of the sponge iron into a form suitable for use in the open-hearth furnace. So far as is known to the writer, none of the sponge iron processes tried in the past have proved to be economically feasible. However, Anaconda had a combination of conditions appearing to justify an attempt to produce sponge iron which would serve for the leach-precipitation-float process. It was thought that the process used in 1914, if changed to a continuous one, might work out satisfactorily. The following favorable conditions at Anaconda justified the investigation: 1—A sufficient tonnage of good grade iron calcine resulting from the roasting of a pyrite concentrate in one of the acid plants, at substantially no cost. 2—Reasonably cheap natural gas. 3-—The fact that there was no need for production of a high grade product. 4— The fact that there was no need for obtaining a consistently high reduction of' the iron in calcine. A small revolving Bruckner-type furnace about 2 ft ID by 4 ft long was set up for early pilot work at the research building. This pilot furnace showed that a satisfactory product could be obtained at reasonable cost. It also indicated a marked advantage in preceding the reduction furnace with a furnace of similar size and capacity for preheating and roasting out any residual sulphur from the feed. The small furnace was operated for several months, various details of the process were worked out. and sponge iron was produced to supply a pilot LPF plant which treated 300 lb of Kelley ore pel- hr. Later a second pilot furnace 5 ft in diam and 12 ft long inside was set up at our reverberatory furnace building. This furnace confirmed the data of the small furnace and gave a basis for design of the final plant. At Anaconda a pyrite concentrate, running about 48 pct S, is recovered from copper concentrator tailings by flotation. This concentrate is roasted to sulphur of 3 pct or less at the Chamber acid plant. The iron calcine contains about 57 pct Fe and 18 pct insoluble. The iron calcine feed, as mentioned before, is re-roasted and preheated in a reroast furnace preceding the reduction furnace. Both are of the Bruckner type. The reroasted calcine is fed into the reduction furnace at 800" to 1000°F along with 30 pct slack coal. In the feed end of the furnace the volatile is burned from the slack, giving a soft coke which readily serves for reduction of the iron. Hard metallurgical coke will not serve the purpose. since it does not reduce CO readily at a temperature of 1850°F. All indications are that the actual reduction of the iron is accomplished by carbon monoxide below the surface of the bed, which is 30 in. deep at its center. Apparently there is a constant interchange: Fe²O³ + 3CO = 2Fe - 3CO², CO² + C = 2CO Actually iron oxide is reduced by CO at somewhat lower temperature than the 1850 °F used in the process. but this temperature is necessary to obtain a satisfactory rate of furnace production. The furnace atmosphere is generally reducing, and typical blue carbon monoxide flames satisfactorily cover the bed. Gas flames from four 3-in. Denver Fire Clay Inspirator burners are played directly on the bed, which is slowly cascaded by the 1 rpm of the furnace. An excess of coke is necessary to assure maintenance of good reducing conditions in the furnace bed. Part of this coke is recovered for re-use.

Jan 1, 1954

By Robert Longyear

IN, diamond-drill work, a true sample consists of all the material cut by the bit-both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. FIG. 1.-CORE BOX. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 12, 1921

By Robert Davis Longyear

In diamond-drill work, a true sample consists of all the material cut by the bit—both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 1, 1923

By Robert Davis Longyear

In diamond-drill work, a true sample consists of all the material cut by the bit—both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 1, 1923

By S. M. Runke, R. G. Meara, O&apos

The Bureau of Mines has been charged by Congress to investigate processes for the production of alumina from low-grade bauxite, alunite, and clay. As one part of the program, an investigation of the application of ore-dressing methods to improve the grade of high-silica bauxite is in progress at the Mississippi Valley Experiment Station at Rolla, Mo. This paper summarizes data obtained so far and presents detailcd results of tests on four typical samples. Mineralogy of Batjxite The name bauxite originally was used to designate the dihydrous aluminum oxide (A1203.2HzO). The designation has been retained, although the existence of a specific mineral of such composition has been disproved. The term is now applied to ores of aluminum consisting of various mixtures of the minerals gibbsite (AlzOa.3H20), diaspore (A120a.H20), and boehmite (Alr-03.H20). The predominant hydrous aluminum oxide in most American bauxite, however, is gibbsite. In some instances bauxite may be amorphous mixtures of the hydrous aluminum oxides that approximate the composition of dihydrous aluminum oxide (A1203.2Hz0). The proposed name for this material is cliachite. Gibbsite and boehmite, the trihydrate and monohydrate, are soluble in a solution of sodium hydroxide at elevated temperature and pressure, whereas diaspore is practically insoluble. The solubility of these two minerals is the basis of the Bayer process of alumina extraction. All bauxites contain certain impurities, the commonest of which, in the order of their importance, are: silica, principally as a constituent of kaolinite, and to a lesser extent as quartz; iron, as hematite, limonite, and siderite; and titanium, as ilmenite, rutile and leucoxene. Minor impurities are zircon, cobalt and nickel. Bauxite is produced commercially in Arkansas, Alabama, Mississippi, Georgia and Tennessee, but the most important deposits in the United States are in Arkansas, in the vicinity of Little Rock. History of Batjxite Beneficiatjon The literature on bauxite beneficiation is limited, but the reports of Gandrud and DeVaneyl and Clemmer, Clemmons, and Stacy2 show the possibilities of flotation as a means of beneficiating bauxite. Their work has also developed reagent combinations that are satisfactory for flotation of gibbsite.

Jan 1, 1944