Search Documents

By A. A. Archer

Marine mining is here defined as the commercial recovery of minerals other than oil and natural gas from the surface of, or below, the seabed by operations connected only indirectly with the land. The number of operations falling within this definition and the number of countries involved are remarkably limited in view of the widespread interest shown in marine mining prospects during the last few years. Marine mining is still restricted to continental shelves, where the only superficial minerals currently being mined are sand and gravel, calcium carbonate in different forms, and tin and iron sands.

Jan 12, 1973

J. L. JONES,* Pittsburgh, Pa.-If a nickel anode is cast under commer-cial conditions, will it contain nickel oxide? Will the nickel oxide affect the rate of corrosion in a double sulfate solution; or will the nickel oxide dissolve in a double sulfate solution? I would also like to ask whether a 98 per cent. pure nickel anode will corrode as fast as a 96 per cent. nickel anode; whether electrolytic nickel will corrode less rapidly than nickel containing a small amount of carbon; and whether the materials some-times used in coating molds for casting nickel anodes will affect the rate of corrosion of the anode? In other words, whether an electrically non conducting coating is likely to be present that will prevent the nickel anode from corroding rapidly. JOHN F. THOMPSON.-The nickel oxide will not dissolve in the double sulfate solution, as far as we know. We do not make the ordinary nickel anode of commerce, but we supply nickel to the nickel anode makers. Those makers almost invariably buy a high-carbon nickel shot, ranging around 0.45 per cent. carbon. In their process, they even further, car-burize it so as to get nickel that will melt easily and be fluid enough to fill the mold, so that the ordinary cast anode on the market is unquestion-ably oxide free. The only time that such an anode will have oxide will be through an error in melting. Some cupola makers of anodes have had trouble with oxidation, but as a rule the anodes are thoroughly carburized; so much so that they probably carry a couple of per cent. of carbon of which around. 1.6 per cent. is graphite.

Jan 12, 1919

By Nathaniel Herz

IN the operation of any ore processing plant, no matter what beneficiation process or combination of processes may be used, certain fundamental figures are regularly needed for essential records and accounting. These include amounts of ore treated and products made, with their assays, as well as quantities of labor and supplies used, with their cost. Usually labor and supplies are broken down and allocated to certain operations by the accounting department, and resulting tabulations are available for study by the milling plant management. However, to avoid too many minor details that would make these reports cumbersome and involved, much information that could be useful to the plant operator is often consolidated in such a manner as to have lost a considerable part of its value. To clarify this point, it may be stated that top management is most concerned with production figures and cost of production, while the plant operator is also interested in quantities of labor in man- hours and amounts of supplies used. Due to varying unit prices of labor and supplies, comparisons on a dollar basis alone are often misleading. With rising unit costs of the past few years now about twice as high as they were a few years ago, constant study of quantities involved is required to improve efficiency and productivity.

Jan 6, 1957

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By H. C. Theuerer

EVEN the highest purity silicon available for semiconductor use contains significant amounts of donors and acceptors, usually aluminum, phosphorus, and boron. Aluminum and phosphorus can be removed from silicon by adaptations of the zone refining techniques' widely used with germanium. Removal of boron, however, has been a difficult problem. The approximate distribution coefficient for boron in silicon is 0.8, so that while zone refining is possible, it is not very effective in any reasonable number of passes. It has been found, however, that boron can be effectively removed from silicon by treatment of a liquid zone with hydrogen and water vapor. Starting with 40 ohm-cm, n-type silicon, use of zone refining coupled with hydrogen

Jan 1, 1957

By Charles M. Cooley

DURING the last week in April, cards were sent out from New York to Institute members affiliated with the Mining, Geology, and Geophysics Div. The cards requested recipients to indicate their main technical interest, within the division, i.e., mining, or geology, or geophysics. The reason for the cards is simple. Within the Institute more than 8000 have expressed either primary or secondary interest in this division. However, there is no way to determine the technical association stimulating this interest.

Jan 6, 1953

By Frederic Dewey

BONE-ASH cupels have been used from time immemorial to absorb litharge, and accompanying oxides; in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge 1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at present it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 11, 1917

By F. P. Dewey

Bone-ash cupels have been used from time immemorial to absorb litharge, and accompanying oxides, in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at resent it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 1, 1918

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

By Victor G. Hills

This paper comprises suggestions on certain points rather than a complete survey of the whole subject. In other words, it is a contribution to the kenera1 discussion invited by John Hays Hammond in his paper, presented as a Presidential address at the Chattanooga meeting of the Institute, in October, 1908.1 Mr. Hammond says, in conclusion: "... I am not offering a code, or even an official and representative declaration of principles.. My remarks are intended, and will, I hope, be accepted, simply as a contribution to that discussion of their theme in which every engineer of experience may participate." Such a discussion has been conducted in technical journals, as well as in contributions to the Transuctions of the Institute; and, in the remarks here offered, I shall have occasion to refer the read& to what I have thus published elsewhere, for more extended statements of my views. What Mr. Hammond says about loyalty to employers, the double capacity of the engineer as an employer, the expert witness, commissions on machinery, the statement that most swindling is done by laymen and not by engineers, duty to the investing public, and the engagement of local engineers as colleagues, it is a pleasure to indorse. Under the head of the expert witness, Mr. Hammond refers to the address of Dr. R. W. Raymond on Professional Ethice. This paper con-

Jan 1, 1911

By D. W. Fuerstenau

A detailed study of the residence time distribution in an industrial balling circuit is presented. Using fired recycle pellets as a tracer impulse in each experiment, material was found to pass through the drum under plug flow conditions with a mean residence time of about 20 seconds. The time for a single pass through the entire circuit is about 60 seconds. Approximately three passes are required for fresh feed to report as product. Segregation of the tracer pellets in the system, according to their diameter, was observed and reasons for this are suggested. These results should be of potential use in the modeling and control of ball balling circuits in the iron ore industry.

Jan 1, 1985

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By R. M. Brick, F. L. Vogel

THE elementary mechanism of deformation in the body-centered cubic metals has been a subject of dispute for many years. If the problem were merely that of designating the crystallographic plane or planes of slip, the solution would have appeared long ago. However, there must be greater differences in the deformation behaviors of the body-centered and face-centered types than the differences in their lattices would suggest. The lines of slip formed on the polished surface of a strained face-centered cubic metal conform to glide over a single plane of the crystal. Slip in body-centered cubic iron, however, is frequently observed as curved and forked lines which could not possibly define a single plane of atoms. This alone is sufficient reason to expect different modes of deformation to operate in the two lattice types. The literature in this field now has generally accepted the proposition that {110), {112), or (1231 planes will act as slip planes in iron. It is essential that the experimental evidence supposedly supporting this proposition be critically examined. Taylor and Elam1 in 1926, using relatively small single crystals, determined the operative slip systems by measurements of the distortion of a grid engraved on the specimens prior to deformation. Their results indicated that shearing had taken place in the close-packed direction on a plane adjacent to or coinciding with the plane of maximum shear which contained the slip direction. This led the authors to propose a theory of noncrystallographic or banal slip. The authors considered an alternate rationalization of banal glide. Slip on two (1101 planes or possibly two {112} planes containing the same <1ll> direction could produce the wavy slip lines. By employing plane segments of varying widths, the integrated plane could take any position in the <111> zone. They rejected this explanation, however, feeling that the preponderance of evidence was against it. Taylor&apos; continued the investigation of the plasticity of the body-centered cubic lattice on ß brass. He reasoned that the resistance to shearing of a given plane in the zone of the slip direction was a function of the angle between the glide plane and the closest (110),: P F=—cose sine cos(X —?) [1] where F is the resistance to shear; P, the axial load at yielding; A, the cross sectional area; e, the angle between slip direction and load axis; x, the angle between plane of maximum shear containing the slip direction and the (101) pole; and ?, the angle between observed glide plane and the (101) pole. Differentiating Eq. 1 and rearranging, dF — = tan(x-?) d? [2] F which expresses the variation of the shear resistance with the angle $. Integrating this equation between the limits 0 and ? yields In F/F0 = ?0?tan(x— ?) d? [3] Here, F, is the resistance to shear of the (110) plane and F is the resistance to shear of a plane $ degrees from the (110). Thus, the variation of shear resistance with $ can be calculated from an experimentally measured x vs $ relationship. Fahrenhorst and Schmid8 sed several methods, none of them involving direct observation, to determine the glide system in ferrite. They determined the variation of critical resolved shear stress with

Jan 1, 1954

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By E. D. Fields, R. W. Sayers, M. C. Tippett

The Duval Corp. porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an econornic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex Cu-Au-Ag ore is treated in a 4000-tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamoiphism and hydrothennal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes fitrther altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well-developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls. Recently, the Copper Canyon and Copper Basin properties of Duval Corp. have been added to the list of porphyry copper mines in Nevada, marking the first new copper open pit in this state in 15 years. The properties are situated in the Battle Mountain

Jan 1, 1970

By Bertrand Robinson

Epitomized, there have been no innovations recently in crushing, but in grinding the trend has been towards larger units under more automatic control with an increased use of autogenous grinding. Crushing Portability of primary crushers to "follow the face" reduces material handling costs. The top size of crusher feed still establishes the size of the crusher; the feed opening should be 1 1/2 times the size of the largest feed. The maximum size of crusher product is 1 ½ times the open scale setting of a jaw or gyratory crusher. Practice dictates use of scalping screens ahead of any type of crusher when the feed contains 25% or more of product size. If required capacity is under 600-700 tph economics favor a double toggle crusher or an impactor. For larger capacities the gyratory crusher is favored.

Jan 1, 1970

By G. F. Ziesing, E. F. Loros, T. J. Smolik

The Golden Sunlight mine began full-scale operations in February 1983 with a conventional open-pit mine supplying 4536 t/d (5000 stpd) of milling ore. After crushing and grinding, the ore is leached with cyanide solution in large agitation tanks. Soluble gold values are removed from the sand portion of the leached ore with five stages of countercurrent washing cyclones. After thickening of the cyclone-wash overflow slurry, the gold is recovered in activated carbon with a six-stage carbon-in-pulp circuit and a five-stage upflow carbon column circuit. Pressure stripping, carbon reactivation, electrowinning, and refining complete the gold recovery process.

Jan 1, 1985

By John Chipman

IT has been long known that the gas evolved during the boil in the open-hearth furnace is mainly carbon monoxide associated with smaller quantities of other gases. A number of attempts have been made to determine the precise effects of carbon and oxygen content of the bath, and of other factors, such as temperature, upon the evolution of carbon monoxide. In his investigation of the carbon-iron oxide product in liquid steel, Herty1 showed that the value of this product at equilibrium could be approximated by plotting the value of the product observed in open-hearth reactions against rate of carbon elimination, and extrapolating to zero rate. The results of this study showed a slight but definite effect of temperature upon the carbon-iron oxide reaction. Experimental studies of the evolution of gases from rimming-steel ingots have not yet attained the degree of precision necessary for an exact understanding of the effects of pouring temperature, carbon content, and iron oxide in the metal upon the composition of these gases. Klinger2 showed that the gas consists mainly of carbon monoxide, and that con-siderable variation in its composition occurs during the solidification of the ingot. In order that these variations may be understood in their proper relationship to the progress of solidification of the ingot and the segrega-tion that accompanies solidification, it is essential to have a knowledge of the condition of equilibrium in the several chemical reactions by which the gases are being formed. It is also necessary to understand the effects of temperature upon the equilibria, and further, to know the manner in which the temperature of the liquid metal within the ingot changes as the skin of the ingot is being built up. The reactions in which we will be chiefly interested are those involving in the one case the oxides of carbon, and in the other case steam and hydrogen, with iron oxide and carbon in the liquid metal. The reactions as they occur in unalloyed liquid iron, and their respective equilibrium constants are written as follows:

Jan 1, 1937

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The apparatus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a ½ -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1-The fine coal, which has been thoroughly

Jan 1, 1952