Search Documents

By Milton Williams

A comparison is made between the amount of interstitial water found by analysis in cores and that estimated from the resistivity curve of the electric log for the corresponding strata of producing reservoirs. It is shown that while the determined and the estimated water saturations are in good agreement in some cases, this agreement may be due to a fortuitous compensation of errors. Estimates of water saturations made from the electric 1og by use of existing relations should, therefore, be employed with caution. Also presented are data on the variation of salinity of interstitial waters in reservoir sands, and on the effect of variation of salinity and porosity on the validity of estimates of water content made from the electric log. INTRODUCTION Throughout the history of electric logging there have been recurrent cycles of optimism and pessimism as to the value of the electric log in the quantitative estimation of reservoir fluid content. The very early days of electric logging were an optimistic period, in which there was widespread faith in the ability of the resistivity curve to reflect fluid content, and in the ability of the potential curve to indicate textural characteristics. In time the accumulation of exceptions to this idealistic behavior brought about a general disillusionment, and caused the more pessimistic of those dealing with electric logs to believe that the sole importance of the log lay in stratigraphic correlation. Within the last several years optimism as to the quantitative use of the electric log has been revived, primarily as the result of the stimulating work of C. E. Archie' on the estimation of interstitial water in sands from resistivity data. Even though the general trend of thought on the quantitative value of the electric log reflects optimism, it is inevitable that there are some widely divergent opinions of the validity of quantitative estimates based on the electric log. A valid method of estimation of fluid content by means of the electric log and a general knowledge of the textural character of the reservoir rock would be of signal importance, not only in that it would save time and money in securing information on reservoirs now being drilled, but also because it would permit the evaluation of reserves in many fields drilled without adequate core data subsequent to the advent of electric logging. Because of this importance, Humble's Production Research Division, in cooperation with various other company divisions, initiated several years ago series of tests designed to evaluate the reliability of estimates of fluid content made from the electric log. The investigation was limited at the outset to sand reservoirs, since it was felt that the inclusion of limestone reservoirs would entail needless complications. In devising these tests it was immediately apparent that the chief difficulty in evaluating the worth of any method of estimation lay in establishing the true value of fluid content. The results of direct analyses of cores cut with ordinary mud were not sufficient, because of the probability of contamination of the fluids by filtrate from the drilling mud; the results of restored state tests on cores were deemed unsuitable because these results can hardly be said to furnish a primary standard. The method adopted was the direct analysis of cores cut with an oil-base drilling fluid. Such cores, when properly handled, are believed to afford the most precise determination of water content available at the present, and, in addition, lend themselves readily to the determination of various other properties which are pertinent to the estimation of fluid content from the electric log. Since it was desired to compare the fluid contents estimated from the electric log run in ordinary mud with cores cut in the same hole, the use of oil-base fluid necessitated the changing over, after all cores were cut, to a conventional mud. This procedure presented several advantages, one of which was that the use of oil-base fluid permitted

Jan 1, 1950

A FEW nights ago while working in the small hours of the morning on a clarion message intended for this page, we repaired to the kitchen for coffee, as is our wont when the solitude of the late hour and the stillness of the night seduce thoughts from the job at hand to reminiscences. The thought occurred, as we slowly dissolved the instant coffee in boiling water, that this modern world of canned, frozen, and dried foods deprives us of some of the subtler and therefore more delightful pleasures of life. We recall the aroma of boiling coffee which greeted us on getting up in the morning before the ease of instant coffee deprived us of the aroma from the old coffees. This line of thinking led us to place the blame on our wife for taking the easy way of making coffee and thereby depriving us of some of our enjoyment. From thinking about our spouse, it is only a short step to thinking about "the boss" or bosses in general.

Jan 9, 1951

By E. R. Force, W. F. Cannon

Many large high-grade manganese deposits occur in marine-transgressive sedimentary sequences deposit fed on stable platforms, although the manganese mineralogy varies from carbonate to oxide facies and host lithologies vary from carbonate- to clay-dominated sections. Examples include the Nikopol and related deposits of the Soviet Union and Groote Eylandt, Australia. Recent work has shown that high sea-level stands are synchronous with stratified and stagnant oceans. We suggest that during transgressions and consequent anoxic events, the anoxic deep waters rich in dissolved manganese were dilute ore-forming fluids. Manganese was precipitated on the oxidized side of oxidation and alkalinity interfaces on shallow shelves. Where the precipitate was preserved, manganese ac- cumulated into ore deposits. Sedimentary manganese deposits have not been widely explored for in North America, nor are they always obvious in outcrop. Large areas of North America are underlain by rocks that we consider broadly favorable for such manganese deposits, and the disparity between the high potential but significant reserves of the United States is difficult to reconcile. Important undiscovered deposits seem likely. An area of Cretaceous rocks in South Dakota is presented as a possible location for a United States deposit analogous to foreign deposits described herein.

Jan 1, 1983

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth's crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth's surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project's capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project's ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985

By Augustus Locke

MY conclusions apply to the engineer in California ore hunting; and, because the product has been overwhelmingly gold, that means gold-ore hunting. But, I wish to think of ore hunting, not as employment for engineers, but as engineering. I wish, moreover, to think of it as productive of ore in significant quantity. The small mine, even if good, means little. Only new districts, or large extensions of old districts can engage our attention here. The conclusions are summarized as follows: (1) The bright color of California mining history comes from the suddenness and intensity of its outburst of gold. Had the mining been averaged from the start, it would soon have become dimmed among greater industries. For fifty years, California has proceeded as an agricultural, timber and oil, but not a mining region. 1

Jan 1, 1931

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period June 10, 1917, to July 10, 1917. Guy N. Bjorge, Boston, Mass. H. H. Lauer, Allentown, Pa. A. H. Burroughs, Jr., Britannia Beach, E. C. Lee, Pittsburgh, Pa. B. C., Canada. Montrose L. Lee, Port-au-Prince, Hayti. Karl Eilers, New York, N. Y. Eugene McAuliffe, Paducah, Ky. H. S. Emlaw, Grand Haven, Mich. R. H..McMillen, Pittsburgh, Pa. W. R. Hamilton, San Francisco, Cal. L. D. Moore, Providence, R. I. Fred N. Hays, Sharon, Pa. Fred J. Pope, New Rochelle, N. Y. E. Hibbert, Nickelton, Ont., Canada. George S. Rice, Washington, D. C. Charles Janin, San Francisco, Cal. W. G. Swart, Duluth, Minn. Milton A. Allen has resigned his position with the Federal Lead Co. and accepted a position with the Arizona State Bureau of Mines, Tucson, Ariz. L. W. Bahney has resigned as Professor at Yale University and accepted a position as metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn.

Jan 8, 1917

By F. M. Jardine

I1944 the cry was for higher production more tons, more metal. New plants were built, capacity of old plants was increased and millmen all over the country were treating tonnages far above normal, sacrificing recoveries to vet that extra metal from extra tons. The list of "critical minerals," at first long, has been scratched until there remains, not a list, but only an item or two. Stocks of all metals and minerals, with possibly one or two exceptions, are now entirely adequate and numerous plants have curtailed or suspended operation.

Jan 1, 1945

By Richard J. Robbins

Mechanical moles have developed through a tedious process of evolution. At times it has seemed that tunnel borers have been subject to the same Darwinian rules of evolution as their zoological namesakes who, despite their efficiency, are highly specialized and still restricted to soft soil conditions near the surface of the ground. HISTORICAL HIGHLIGHTS The Robbins Co. began its work in this field in 1947 with the development of a twin-bore continuous coal miner. Although these machines were used primarily in coal, two of the early prototypes were used to bore tunnels through shale. Disk cutters were first used on these machines and showed promising results as core breakers between drag-bit kerfs. In 1953, James S. Robbins and Assocs. undertook the development of a 25-ft 9-in.-diam circular tunnel borer for Mittry Construction Co. to be used at Oahe Dam in South Dakota (Fig. 1). This is believed to be the first rock tunnel-boring machine built since the end of the 19th century when short sections of the Channel tunnel were successfully bored in chalk from both the English and French shores. Another Oahe Dam machine was built in 1955, and then a series of three small-diameter machines for the company's first real experience with medium-hard and hard rock (Fig. 2) None of these three could be considered a success, although they laid the groundwork for the success that followed. Interbedded shale and limestone in Pittsburgh and hard limestone in Chicago quickly pointed up the weaknesses in these machines which were used by Perini, Dravo, and Healey. Among the problems were the high breakage rate of tungsten-carbide drag bits, too much flexibility in the drive shafts, failure of high-pressure hydraulic systems, chain-conveyor failure, and general lack of rigidity and strength. In 1956 another attempt at medium-hard and hard rock-boring proved this time to be a success and a significant turning point in the development

Jan 1, 1970

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß' and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß' varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By T. T. Read

JAPAN'S iron and steel industry has always been closely connected with military strategy. Many years ago it became evident that the country's iron-ore resources were too small to support any extensive industry. As a result a belief in the imperative necessity of securing such resources has influenced Japan's political and economic policy in the Far East. Iron-ore developments in China are too well known to need repeating except to note that they have been rather unsatisfactory to both China and Japan. The ore deposit at Tayeh, in China, is not as large as was first believed and, though that and other sources of supply in China proper are now furnishing Japan a little more than a million tons of ore yearly, it cannot be counted upon as a large permanent source of supply. The deposit in Shantung proved so disappointing on further exploration that operations there have, so far as I know, long since ended. The operations at Pen-bsi-hu, in South Manchuria, which C. F. Wang de¬scribed in the A.I.M.E. TRANSACTIONS for 1918, Vol. 59, were reported to have yielded 84,000 tons of pig iron in 1928 and about 50,000 in 1935, so they seem to be going back.

Jan 1, 1937

By Richard R. Zupp, David A. Stevenson

An experimental method to determine the carbon activity in various solid solutions was developed. Samples of the solid solutions and an Fe-C reference sample were equilibrated with respect to carbon content by annealing them in a Hz-CHI gas mixture in a closed cell. The carbon content of each sample was determined, and the carbon activity was obtained from the carbon content of' the reference sample and well-established data for the dependence of the carbon activity on the carbon content in Fe-C alloys. The influence of vanadium on the activity of carbon in austenitic Fe-C-V alloys at 1000°C was determined by this technique. A general semiempirical correlation was developed to describe the dependence of the activity coefficient of- carbon on the composition of ternary austenitic iron-base alloys containing interstitial carbon and a substitutional solute. The correlation is particularly useful in predicting the partitioning of- carbon between various alloys. THE influence of substitutional solutes on the activity of interstitial solutes in metallic solid solutions is important in the theory of alloy phases. Solid solutions of particular interest are the fcc austenite phases of ternary Fe-C-Z systems, in which carbon is the interstitial solute and Z represents any substitutional solute. Carbon-activity data are also needed in these solid solutions to solve practical problems; the quantitative treatment of diffusion-controlled transformations' is an examvle. Experimental information is available for ternary austenitic solid solutions containing Mn,2 Si,2 and A16 as the substitutional solute. Because qualitative preliminary studies indicated that vanadium appreciably decreases the carbon activity,14 the present investigation was undertaken to determine the influence of vanadium on the activity of carbon in austenite. Although Flender and ever" measured carbon activity over a range of compositions in the Fe-C-V system, they were primarily interested in determining phase boundaries in the ternary system, so most of their measurements were outside the composition range for stability of single-phase austenite. Petrova and Shvartsman' also made limited measurements of the carbon activity in Fe-C-V alloys. The dependence of the carbon activity on the carbon content of an alloy may be determined by passing COCOz or H2-CH4 gas mixtures of carefully measured composition over the alloys, determining their equilibrium carbon content, and utilizing the relevant equilibrium relationships. smith16 used this technique with both CO-COZ and HZ-CH4 gas mixtures to determine the dependence of carbon activity on carbon content in pure Fe-C alloys. His data, which are in good agreement with those of some previous and subsequent investigators,6'17 but not with those of others,lfl'ao are usually considered to be the most reliable. Although the same method can be applied to Fe-C-Z alloys, it is difficult experimentally, because the appropriate gas mixtures are almost pure CO or Hz. A simpler technique is to simultaneously equilibrate the Fe-C-Z alloys and pure Fe-C alloys with the gas mixtures, and then use Smith's data to determine the carbon activity in the pure Fe-C alloy. A number of investigators have employed this technique. others Have used the partitioning of carbon at the interface of a diffusion couple prepared from an Fe-C alloy and a Fe-C-Z alloy. In the present study, a closed-cell method was developed by which carbon was selectively transferred via a gas medium between pure Fe-C alloys and Fe-C-V alloys which were not in physical contact. A similar method was developed independently by Heckler and winchel14 and used to study the Fe-C-Ni system. EXPERIMENTAL METHOD A schematic diagram of the experimental arrangement is shown in Fig. 1. In a typical experiment, a 5-g Fe-C sample was placed in one compartment of a quartz cell, and a 5-g Fe-V sample was placed in each of the other compartments. The cell was evacuated, outgassed, backfilled with approximately 125 Torr of hydrogen, and sealed. After being placed in a fur-

Jan 1, 1967

By Clyde Williams

A MAN who is a first-class metallurgist, engineer, and scientist and an outstanding organizer, administrator, and executive and who, at the same time, has an innate ability to "make friends and influence people" everywhere he goes is an exceptional personality at any time. And if such an individual can retain this combination of virtues during a great war despite the fact that the Government loaded him with enough work and responsibility for three such men. he is a most exceptional personality. And if he can keep his head and maintain an unfailing sense of humor during the trying war years and, while dealing with hundreds of jittery metallurgists and metalworkers, with Army and Navy brass, and with red-tape-entangled war agencies by the dozen, he is a rare personality indeed. Such a man is Clyde Williams, director of Battelle Memorial Institute. who will be President of AIME in 1947. The Institute is fortunate in having him as its mentor during what may be a critical and important year.

Jan 1, 1947

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

Between two and three years ago, in response to an unmistakable and insistent demand, the four Founder Societies appointed Committees on "Aims and Organization," or on "Development," charged with reporting on the internal organization and the external (non-professional) ac-tivities of the engineers societies and to advise as to coöperations and coordination. Each of these committees formulated a report, recognizing that effi-ciency in external activities could only be attained by intimate coopera-tion between the four Societies. As a consequence, each of the Founder Societies was requested to appoint members of a Joint Conference Committee, charged with discussing the situation and evolving if possible a plan of cooperation in external activities which would coordinate not only the efforts of the four Founder Societies but also other national technical and scientific societies, as well as local engineering and profes-sional associations, groups or clubs. The Joint Conference Committee entered on its task with enthusiasm, and after great labor evolved the outline and many of the details of plan for engineering cooperation in public and inter-society activities. This report has now been submitted to the Boards of the Four Founder Societies, and has been ordered printed by our Board for the information of our members.

Jan 12, 1919

By AIME AIME

T HE 121st meeting of the Institute held in New York City, February 16 to 19, 1920, was a great success despite vicissitudes of weather of unusual severity. On account of tremendous snowstorms, only two members of the Canadian contingent arrived, and several of our members from the west arrived thirty hours late. Two weeks prior to the meeting, the heaviest snowstorm in 34 years wrecked the surface transportation in New York; and it was only by special dispensation that arrangements were effected, with the New York Street Cleaning Department to clear away 39th street in front of this building so that vehicles could reach the curb. The total registration of members and guests was 1138.

Jan 1, 1920

By G. S. Baker, S. H. Carpenter

Langenecker has reported significant reduction in strength of high-strength metals during ultrasonic t'ibration. Decreases in static yield stress an order of magnitude greater than the calculated stress amplitude of vibrations were reported by him for a stainless steel and for tungsten. in the present work, attempts were nzadc to verify such large reductions in yield and flats stresses using resonant librations of measured amplitudes. The results show that both the soft metals (copper and aluminum) and the high-strength metals (sleels) hare reductions in yield and .flow stresses no larger than the stress amplitude of libration. BLAHA and Langenecker,' investigating the effect of vibratory stresses on the deformation of zinc and aluminum, found a decrease in the static yield and flow stresses approximately equal to the vibratory stress imposed. Langenecker later extending this work to high-strength metals such as stainless steels and tungsten2 found a much larger effect. In these metals the static yield and flow stresses decreased by an amount more than an order of magnitude greater than the calculated vibratory stresses. It was suggested that this phenomenon could be a serious hazard to high-strength structures in an acoustic environment, such as a large rocket at launch, or could be used advantageously in the working of hard-to-work materials such as the refractory metals. Langenecker and others3 have investigated the effect of high-amplitude vibrations on many metal-forming operations. The results have been quite favorable with usually a large decrease in the energy necessary for the forming operation. The processes, however, involve large frictional forces and it is not clear whether the decreases in forming forces are to be ascribed to decreased friction or to decreased flow stresses. The present paper reports an attempt to determine the effect of accurately known vibratory stresses on the static yield and flow stresses. I) EXPERIMENTAL TECHNIQUE The standard multicomponent resonator technique for measuring internal friction has been adapted to allow simultaneous high-amplitude vibration, internal-friction measurement, and tensile deformation. This has been described in detail elsewhere.4 Longitudinal oscillations of approximately 50 kc frequency are excited in a multicomponent resonator by a quartz transducer. A second transducer measures the amplitude of vibrations. Fig. 1 shows a schematic drawing of the resonator and grip arrangement and the displacement pattern produced. Since the centers of the dummy bars are at displacement nodes, they represent points where attachments will not materially affect the vibrations. The force is applied by a standard Instron tester. The sample may be deformed while simultaneously vibrating at up to 104 strain amplitude. 11) EXPERIMENTAL RESULTS The effect of high-amplitude vibrations on the yield and flow stresses of copper. aluminum, tantalum. a soft iron, and a stainless steel has been measured. In addition samples of tungsten vibrating at stress levels up to 10' dynes per sq cm have been subjected to static stresses near the static yield stress with no indication of macroscopic deformation. Fig. 2 gives typical results for 99.999 pct polycrys-talline copper. A vibratory stress of 7 x 107 dynes per sq cm is applied at points "a" and removed at points "h". The behavior of aluminum is identical. In agree-

Jan 1, 1967

By Edward L. Beutner, Robert M. Crump

Benson Mines low-grade iron ore reserve is a replacement deposit within the Grenville gneisses of the Adirondacks. The average grade of the crude ore is about 23 per cent iron. The iron minerals are principally magnetite and hematite disseminated throughout the gneisses as discrete grains about 1 mm in size. Both the ores that are beneficiated by magnetic means and the non-magnetic ores that are treated by a gravity method of concentration are found in stratigraphically different positions but are mined from one open pit, which is about 2.5 miles long and 800 feet wide and are treated separately. The gneisses are described and named according to the distinctive mineralogy of each. Recognition of the gneissic types permits the interpretation of the structure as a northward-plunging syncline overturned to the west. A large subsidiary anticline-syncline complex occurs on the east limb of the major syncline. Iron minerals in sufficient quantity to be considered ore are confined to areas where the footwall rock has been overturned to become the hanging wall.

Jan 1, 1968

Herbert A. MegRaw, San Luis de la Paz, Guanajuato, Mexico (communication to the Secretary *):—I am in entire accord with the basis of Mr. Lamb's argument, that the stamp

Jan 1, 1911

By T. J. Whalen and Michael

The grain shape of the carbide in nickel-bowled ad cobalt-bonded titanium carbides was studied by microgiaphic examination, and the influcence of sintering atmosphere, sintering substl-after, ami the amount of metal binder on the grain shape was determined. If was found that the Carbide grain cross sections in the nickel and cobalt cermets ranged from round to angular, depending on the sintering conditions. The spheroidization of the carbides in both cobalt-bonded and nickel-bonded titanium carbides may be attribicted to oxygen. In the course of studies on titanium-carbide base cermets, various investigators have reported on the shape of the carbide grains, and it was noticed that grain shapes were obtained which were either spheroids, or polygons with rounded or square edges. It was also noted that the shapes of the carbide grains changed with time or composition. skolnickl showed that the titanium-carbide grains. after infiltration in vacuum with nickel tended to spheroi- dize with time. The titanium-carbide skeleton was located on a beryllia plate during infiltration. Gur-land,' who studied the microstructure of titanium carbide-cobalt compacts, showed that the carbide grains are round after 1 hr at 1450oC in a hydrogen atmosphere and angular after 7 hr at the same temperature. Goetzel3 has found that the carbide grains in compacts with a high binder content. 40 to 60 pet. tend to be spheroidized. whereas Blumenthal and silverman4 pointed out that the higher binder contents could yield either round or rectangular grains with rounded edges. depending on the nature of the binder. It is the purpose of this paper to present experi-

Jan 1, 1961