Search Documents

By Jerry B. Newby

In the central Ohio area well completions and new production each increased 60 per cent. in 1928 over the previous year. Gas wells increased only 27 per cent. The ratio of dry holes to total completions was unchanged. Ashland County led with 113 completions; a new pool in the shallow Berea sand near Jeromesville stimulated activity. Licking County in the Clinton deep sand territory, however, lead in new production with 972 bbl. Two other deep sand counties followed closely, Coshocton with 831 bbl., and Muskingum with 718 barrels. The Trenton rock or Lima field of northwestern Ohio declined sharply in oil well completions to 130 for 1928 from 210 for the previous year. New production increased from 3000 to 6100 bbl., the increase coming from the Murphy pool in Liberty township, Seneca County. The total of gas wells was unchanged as compared with 1927. The ratio of dry holes to total completions rose from 13 per cent. in 1927 to 27 per cent, in 1928. The largest producer in the Murphy pool made 1200 bbl, in the first 24 hr. The total depth of the wells in this pool averages 1475 ft.; average initial production, 125 barrels.

Jan 1, 1929

By Nelson Severinghaus

AS far back as 40 years ago management made the initial steps toward utilizing the large amount of reject marble produced by the dimension stone quarries in sized products. In 1947 the Calcium Products Div. of the Georgia Marble Co. was organized to manufacture crushed, ground, and screened products from Georgia marble.* It became obvious early in operations that salability of any products of this type was determined by several factors: high calcium carbonate content, whiteness, dryness, and cleanness. Because no reject material could consistently meet these specifications, Calcium Products Div. now operates three underground quarries for raw material feed. In underground operations no stripping is required, surface contamination and trash are eliminated, weather causes no operational difficulties, and the raw material is maintained dry for plant processing.

Jan 12, 1957

By David R. Mitchell, E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are-presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and conform, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance comes and jigs are usually dispensed with, and other methods, such as the Hydro-tator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh.

Jan 1, 1950

By D. Gupta, S. Weinig

This investigation comprises the study of dislocation-oxygen interactions in a! titanium and its effect on the ductile to brittle transition in titanium. Internal friction techniques using a low-frequency lorsion pendulum were used to study the oxygen atom interactions with dislocations in "superpurity" titanium. A calculation of the interaction energy between an oxygen atom and a dislocation, based on the "breakaway" strain resulted in a value of 0.015 ev as compared to theoretical values of 0.022 and 0.035 ev for edge and screw dislocations, respectively. Both the saturation of the room temperature decrement and the transition from ductile to brittle behavior occurred at 1.5 at. pct 0. It was proposed that the embrittlement was due to oxygen atoms immobilizing the dislocations. It was possible to increase the ductility of the Ti-0 binary alloys by decreasing the oxygen pinning. The increase in uniform elongation was 30 pct for an increase in the preanneal temperature of 300°C. ThE room-temperature ductility of a titanium is significantly affected by interstitial solutes. Although oxygen has a solid solubility of 15.5 pct by weight, the room-temperature ductility extends only to 0.6 pct.' The ductility precipitously falls at this concentration and the fracture characteristics change from ductile to brittle.2 The small effective bulk composition of solute required to destroy the room-temperature ductility of the titanium must be indicative of an in-homogeneous distribution of solute atoms. Internal friction techniques were used in this investigation to

Jan 1, 1960

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,' Si." —large a solubility: Al.9

Jan 1, 1954

By R. W. Prouty, R. T. Green

The object of this paper is to describe, as concisely as possible, the methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz. Because of the difference in occurrence, manner of prospecting, and methods of mining, the sampling and estimating practice falls into two divisions: That for the underground operations, and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three main classes: Replacements of limestone, replacements of porphyry, and replacements of contact breccia. The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies, it is exceedingly difficult, without sampling, to determine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft, As some of the orebodies are from 100 to 300 ft. thick, it can be seen that the smaller ones form a difficult prospecting and estimating problem. In the replacements in porphyry, both underground and in Sacramento Hill, the boundary usually cannot be determined without sampling. There is a gradual decrease in value until barren material is reached; this gradation may occur within a short distance or it may extend for several yards.

Jan 1, 1925

By Clyde Wyman

THERE has always been a question as to the extent to which oxidizable alloys might he recovered from charged scrap in the, acid electric furnace. While qualitative information was not lacking, the quantities that might be recovered and the conditions best suited for such recovery were not clearly defined. The present investigation was carried out to determine the efficiency of alloy recovery from residuals contained in the bath, especially in regard to the recovery of vanadium. A series of 24 heats was produced at the Burnside Steel Foundry Co., including medium manganese-molybdenum-vanadium, manganese-chromium, and grade B steels, in which vanadium recoveries from the residual vanadium were investigated. Recoveries of other alloys were also studied from the accumulated data. These heats were produced in a 5-ton acid-lined electric furnace. The analysis of metal and slag samples and the micrographs were prepared by the Research Laboratories of the Vanadium Corporation of America. In addition to the vanadium contained in the scrap charge, ferrovanadium was added to the charge and to the molten bath to bring the residuals up to the desired level. Vanadium pentoxide (V2O5) in one series of heats was added to the bath after meltdown, for the same reason. In addition to the general furnace practice, the slags of these various heats were treated with coke breeze, Ferrocarbo-S (silicon carbide), and aluminum dross to determine the effects of different reducing agents upon the alloy recoveries and upon the final product.

Jan 1, 1947

By E. H. Miller, E. J. Hall, M. J. Flak

It is well known that, with the exception of the so-called " niter-and-nails " method, all methods used for the fire-assay of salphide-ores,* especially those of iron, zinc, lead and copper, are very tedious and require the constant attention of the assayer. The objections to the niter-and-nails method are: The liability of the charge to boil over, due to the presence of the' niter; the low results in silver (uncorrected); and the frequently large discrepancy between the actual weight of the lead button and the calculated weight. In many cases the buttons are too small to collect all of the gold and silver contained in the sample, while in others they are too large for cupellation. It was thought that, if these objections to the niter method could be eliminated, it mould give a method for the crucible-assay of sulphide-ores, and especially the low-grade ores of zinc and copper, which would be superior to any method in use at the present time. The only similar methods of assay are those of Perkins,t Rhead and Sexton,$ and Mitchell. The method of Perkins requires too much litharge for it to be a commercial success; that of Rhead and Sexton, utilizing the prelimiilary assay we found to be the best;—the charge for the final assay, however, was modified by having borax-glass added to it; also, the oxidizing power of the niter mas determined by a charge which difters from either the preliminary or the

Jan 1, 1904

By W. C. Hazen, A. V. Henrickson

URANIUM plant operations of the Kerr-McGee Oil Industries at Shiprock, N. M., began in December 1954. As originally designed, the plant treated Plateau carnotite ores by the acid cure process, which dissolved both uranium and vanadium minerals. After 16 hr of acid curing, the ore was conveyed to an agitator and leached for 2 hr in acid liquor at a pH of 1.0. The leach pulp was then separated at 100 mesh in a classifier, the sands continuing through a washing classifier circuit and the slimes going to a countercurrent decantation system of four thickeners.

Jan 9, 1957

By J. H. Scaff, J. E. Kunzler

The measurement of the electrical, thermal, and magnetic properties of metals at low temperatures, primarily in the range of liquid helium below 4.2°K, is a powerful tool for investigating many of the fundamental properties of the metallic state. Such measurements also have many practical applications, particularly as an analytical tool. One example of the practical utility of such measurements is illustrated by a short study we have made of the low-temperature resistance of copper used in preparing varistors. Copper-oxide varistors are prepared by the thermal oxidation of copper. This results in the

Jan 1, 1959

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the navies of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ARNOLD, RALPH, Member of. Board of Tax Reviewers in connection with the administration of the War Revenue Act. BACON, RAYMOND F., Lieutenant-Colonel, Chemical Service Section, N. A., A. E. F. BALLENBERG, A. G., 1st Lieutenant, Ordnance Dept., U. S. A. BARCUS, WALTER J. E., Captain, Gun Division, Ordnance Officers' Reserve Corps. BECKWITH, H. T., Captain, Engineer Reserve Corps, Headquarters Co., 312th Engineers.

Jan 6, 1918

By Harmon D. Nine

DISCONTINUITIES in the strain vs cycles to failure (S-N) fatigue curves have been reported for polycrystalline materials by Porter and Levy for copper,&apos; by Benham and Ford for mild steel,&apos; and by Williams and Stevens for 18/5 stainless steel.3 However, the considerable scatter of the points for polycrystalline materials have made a statistical analysis of the data necessary to confirm the discontinuities. By using oriented single crystals of high-purity material and low grown-in dislocation content, the reproducibility has been improved to a degree which makes statistical analysis unnecessary and clearly shows discontinuities in the S-N curves. A recent publication4 reports an abrupt change of slope in the S-N curve for ( 100) axially oriented copper single crystals fatigued in torsion. The reported discontinuities in the S-N curve, along with a different mode of failure in the two branches of the curve, have been interpreted as being due to two different amplitude-dependent mechanisms. Further work on copper single crystals of (111) axial orientation has now been completed which supports the existence of an amplitude-dependent change in the mechanism of fatigue. In the present study torsional-fatigue experiments were performed at room temperature in air on (111) axially oriented single crystals. The crystals were grown and prepared as reported in Ref. 4. Two different methods of growing the crystals also discussed in Ref. 4 produced crystals of two different perfections: Type I with dislocation density of >l06 per sq cm and Type I1 with dislocation density of <l05 per sq cm. In accordance with the accepted hypothesis that crystal flaws are primarily responsible for the scatter of fatigue lifetimes, particularly at low amplitudes, the values for the three lowest amplitudes for Type I crystal are believed to be uncertain. They are marked in braces in Fig. 1. On the other hand, at amplitudes above a surface shear strain (SSS) of *0.003, the data for both types of crystals are in agreement. Most remarkably the S-N curve for torsional fatigue of (111)-oriented single crystals is composed of three segments separated by rather large discontinuities, Fig. 1. Metallographic and X-ray measurements indicate that the lower branch corresponds to the low-amplitude (F) region of the (100) copper single-crystal results as discussed in Ref. 4, and the two upper branches correspond to the high-amplitude (H) region. The lower discontinuity in the (111) S-N curve and metallographic evidence give further support to the hypothesis that different mechanisms of failure operate for high and low strain amplitudes. Reference to the resolved shear stress diagram, Fig. 2, shows that the highest stressed systems in

Jan 1, 1965

By Leon W. Dupuy

SUPPLEMENT THESE tables should accompany Figs 6, 7, 8, 9 and 10, respectively. To follow Fig 6: TABLE 2[a]-Drill Rod [ ] To follow Fig 7: TABLE 3-Rod Coupling [ ]

Jan 1, 1947

By Horace F. Silliman, Curtis L. Wilson, Eugene C. Little

The change in electrical resistance and Rockwell hardness (16-100-B) of copper alloys containing Ni2Si and Co2Si was determined by annealing the quenched solid solutions at various temperatures for various lengths of time. The rate of precipitation of Nisi, as measured by the rate of decrease of electrical resistance and increase of hardness, increased with annealing temperature up to a certain point, depending on the percentage of Ni2Si present. At these temperatures discontinuities in the rate: change occurred. Similar discontinuities in the Co2Si alloys were no The solubility of Co2Si in copper was found to be 5 per cent at 970" DISCUSSION (Robert F. Mehl presiding) R. I?. Mehl, Pittsburgh, Pa. (written discussion).—The electrical conductivity and hardness curves reported in this paper are interesting, particularly because many of the anomalies of the precipitation processes are evident from such curves. The title of the paper, however, is deceptive, for it implies that measurements of electrical conductivity and hardness are suitable to determine the rate of precipitation. Neither of these methods is suitable for a quantitative measurement of rates of reaction or of precipitation in the solid state. Electrical conductivity in some alloys shows an anomalous increase during the first stages of aging at low temperatures; it is notably sensitive to strain and to state of subdivision. I have plotted the conductivity curve representing the decomposition of the phase at 555" C. in the copper-aluminum system, given in the paper by Smith and Lindlief (Fig. 47, p. 93) as a rate of reaction curve, and compared it with the curve determined by area evaluation (Fig. 7); these two curves are not coincident. Hardness is likewise very uncertain, for it is so much dependent upon particle size. Of the various methods proposed for the study of rates of reaction and precipitation, the evaluation of volume of reaction product from the respective area of matrix and reaction product on the photomicrograph is the most trustworthy; suffering, perhaps, only from low sensitivity during the early stages. This method, used originally by Davenport and Bain and now by Smith and Lindlief, is suitable for

Jan 1, 1933

By Harmon E. Keyes

Harmon E. Keyes (Chemical & Metallurgical Engineer, Eagar, Ariz.)-Chemical dissolution of chalcocite by acidic ferric sulfate is well known. Resulting elemental sulfur may be oxidized to sulfuric acid by heated ferric sulfate. Laboratory tests at Southwest Experiment Station, USBM, Tucson, generally confirmed stoichiometric relations of 1 part Cu dissolved to 1.750 parts ferric iron reduced, using CP chemicals, dried ore samples, and apparatus cleaned with potable water. Recirculation with open-drainage percolation to increase copper in leaching solvent was followed successfully when appropriate, both in laboratory and Pinto Valley pilot tests. Before 1924 attempts to produce ferric sulfate by aerating ferrous sulfate solution were known. Initial oxidation was satisfactory, but rate slowed below practicality as oxidation progressed and acidity increased. Also, due to hydrolysis of ferric sulfate, a ferric precipitate of hydroxide and basic sulfate resulted. Both laboratory and pilot plant tests gave similar results, regardless of whether CP ferrous sulfate or scrap iron cementation discard solution was used. Rapid oxidation of ferrous hydroxide by air alone is well known to analytical chemists. I demonstrated a process to produce acidic ferric sulfate solutions by precipitating ferrous hydroxide with milk of lime, aerat-

Jan 1, 1973

By R. W. Raymond

I desire to call the attention of members of the Institute to a new method of plotting and determining faults in mineral deposits, suggested by Prof. Hanns Hoefer, lately of the Mining School of Przi-

Jan 1, 1882

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author&apos;s values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author&apos;s can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author&apos;s reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.&apos; Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By K. B. Nowels

The attainment of efficient flooding to a large extent depends upon a knowledge of fluid movement through porous media and the pressures used in controlling this movement. Little has been understood con-cerning the fundamental principles involved in the forced drive of water-flooding and an attempt will be made to present some data which may be of interest. Considerable data and technical information pertaining to natural and artificial water-flooding have been presented in the past by Torrey, Umpleby, Fettke, Panyity and others. Their papers have thoroughly covered the description of past and present-day methods of oil recovery by flooding in the Bradford field, especially an article by Torreyl in the Petroleum Engineering Handbook. A bibliography of papers devoted to watcr-flooding, published in Mr. Torrey&apos;s article, is appended to this paper. No attempt has been made, therefore, to describe the installations and procedure necessary in flooding, thus permitting the writer to deal exclusively with the mechanics of water movement in flooding operations and its relationship to well spacing. Artificial water-flooding will probably always be the most successful in oil fields described by Herold as being under "capillary control"" and will probably be useless in fields naturally under hydraulic or volumetric control. The natural water drive in an oil field under either of these two controls may give efficient recoveries, as a result of the regulated encroachment of edge water. Such a "natural flood" resulting from the influence of edge water must not be confused with the term as used in this paper, however. Any reference to "natural flood" will here refer to the old method of flooding formerly used in the Bradford field. This was discovered largely by accident and utilized the hydrostatic pressure created by a column of water standing in a watered-out oil well in forcing the oil to an adjacent producing well. The same principles are involved in either natural or artificial flooding, and the latter method simply

Jan 1, 1933

By D’Arcy A. Shock, J. G. Davis

Continental Oil Co. has spent more than four years of research on the fundamentals of recovery of potash by solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multiwell mining systems were studied in the field work. This paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test.

Jan 1, 1970