Search Documents

By V. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries. THE purpose of this paper is to present the results of an investigation into the possibilities of separating precious metals from anode slimes by selective flotation. The work was carried out at the State Research Institute in Helsinki, Finland. The sample of anode slimes tested was submitted by the Outo-kumpu Co. in Finland. In 1947 the average assay of filtered and dried anode slimes in the Outokumpu refinery in Pori was as follows: Au, 0.50 pct; Ag, 9.38 pct; Cu, 11.02 pct; Ni, 45.21 pct; Pb, 2.62 pct; Fe, 0.60 pct; Sn, 1.00 pct; Sb, 0.04 pct; As, 0.70 pct; Se, 4.33 pct; S, 2.32 pct; SO,, 2.17 pct; SiO2, 2.25 pct. The daily assay naturally varies considerably from the figures presented above. The present conventional method of treatment of anode slimes consists of the steps shown in the flowsheet in fig. 1. As seen from this simplified flowsheet, the present method of treatment involves many steps by which the components of the anode slimes are removed one after another until the main products, gold and silver, may be separated. Due to the small scale of operations, the above procedure is carried out in small batches requiring considerable amount of manual labor. If, however, the anode slimes could be treated in

Jan 1, 1951

By J. W. Harden

THE observations here following are the result of an examination made as to the feasibility of extending the South Mountain Railroad from Pine Grove to Waynesborough, and of the commercial value of the ore through which such extension would be made to pass. The road at present built and in operation has a junction with the Cumberland Valley Railroad, half a mile east of Carlisle, and extends southward to Pine Grove, a distance of 176 miles. The extension proposed will add to it near 27 miles, making its total length 44$, more than 23 of which will run through, or in close proximity to, beds of ore. Along the route taken there are a number of openings at which the ore is gotten, of which the Craighead bank, Huntzinger's bank, Lowrey's bank, Wenkoop's bank, the Henry Clay bank, the Fuller

By J. W. Harden

THE observations here following are the result of an examination made as to the feasibility of extending the South Mountain Railroad from Pine Grove to Waynesborough, and of the commercial value of the ore through which such extension would be made to pass. The road at present built and in operation has a junction with the Cumberland Valley Railroad, half a mile east of Carlisle, and extends southward to Pine Grove, a distance of 172 miles. The extension proposed will add to it near 27 miles, making its total length 442, more than 23 of which will run through, or in close proximity to, beds of ore. Along the route taken there are a number of openings at which the ore is gotten, of which the Craighead bank, Huntzinger's bank, Lowrey's bank, Wenkoop's bank, the Henry Clay bank, the Fuller

Jan 1, 1873

The October issues* of the Journals of the three AIME Societies carried a brief resume of the historical development of various technical and professional organizations which in some immediate or remote way affect the individual member of AIME. This resume was presented by the Institute Committee on Inter-Engineering Society Cooperation. Recently, several plans have evolved designed as a first step to provide a so-called "unity organization" for the entire engineering profession. Almost all of the plans involve Engineers' Joint Council, Engineers' Council for Professional Development, and National Society for Professional Engineers in some way or other. Hence our committee is presenting to our membership a resume of the recent activities of the two umbrella organizations and of NSPE. More detailed information on any of these organizations may be obtained from annual reports published by the organizations.

Jan 2, 1961

By Richard R. Parizek, E. Scott Blair

Numerical modeling of ground water flow systems can be used to help analyze many practical problems encountered in the mining industry. Numerical models can be used to predict ground-water seepage rates into surface mines, shafts, and other large excavations; to predict water-level changes under adjacent properties; and to predict the effectiveness of various deep-well dewatering schemes. As with any model, the results from a numerical model are limited by the quality and quantity of data, and by the restrictions of any simplifying assumptions. A case study is presented that shows how a numerical model was used for engineering purposes to help analyze the hydrologic impact of a proposed open-pit mine by Predicting changes in the dewatering rate caused by the lateral growth and deepening of the mine and by predicting the effectiveness of various deep-well dewatering schemes.

Jan 1, 1982

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean's equation (Eq. [4] of Gifkins' paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean's equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"' on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins' work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins' results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins' results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author's reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By S. W. Parr

The extent to which geological carbonization has taken place in the process of coal formation is a fundamental factor in all considerations relating to classification, oxidation, deterioration, spontaneous combus tion, and especially in all considerations relating to destructive distillation having as an objective the production of marketable coke and by-products. Moreovcr, it may be readily shown that a striking relationship exists between the geological decomposition or geological carbonization processes and those artificially produced by heat. This may be well illustrated by bringing again to view some of the charts more commonly mct with 25 years ago, as in Fig. 1.' In this figurc the line of geological decomposition by decay, pressure, etc., because of its relation to the line of carbonization by destructive distillation, becomes of special significance when we attempt to formulate any system of classification which shall be reasonably scientific and at

Jan 1, 1927

By S. W. Parr

THE extent to which geological carbonization has taken place in the process of coal formation is a fundamental factor in all considerations relating to classification, oxidation, deterioration, spontaneous combustion, and especially in all considerations relating to destructive distillation having as an objective the production of marketable coke and by-products. Moreover, it may be readily shown that a. striking relationship exists between the geological decomposition or geological carbonization processes and those artificially produced by heat. This may be well illustrated by bringing again to view some of the charts more commonly met with 25 years ago, as in Fig. 1. 1 FIG. 1. In this figure the line of geological decomposition by decay, pressure, etc., because of its relation to the line of carbonization by destructive distillation, becomes of special significance when we attempt to formulate any system of classification which shall be reasonably scientific and at

Jan 2, 1926

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By Herbert Clark Hoover, Lou Henry Hoover

MANY persons hold the opinion that the metal industries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requiring not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. For a miner must have the greatest skill in his work, that he may know first of all what mountain or hill, what valley or plain, can be prospected most profitably, or what he should leave alone ; moreover, he must understand the veins, stringers1 and seams in the rocks2. Then he must be thoroughly familiar with the many and varied species of earths, juices3, gems, stones, marbles, rocks, metals, and compounds4. He must also have a

Jan 1, 1950

By Thomas M. Plouf

Getting optimal performance from flotation cells can, in many cases, be critical to a project's economic viability. Simple testing procedures can sound early warning signals as well as maintain optimum recoveries from the flotation cycle. The materials required for a simple testing laboratory include: (1) pH meter or pH paper, (2) bottles of reagents used in plant flotation, (3) stop watch, (4) calibrated eye droppers. (5) laboratory flotation machine (1000-g tank, open impeller), (6) froth collection pans, (7) magnifying glass, (8) sizing screen sufficient to retain 10% of the flotation feed coarse fraction, (9) sizing screen for the size particles at which desliming of the plant flotation feed is to take place, and (10) a set of screens covering the complete range of feed particle size.

Jan 4, 1978

By Leon Merker

Flame fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904, was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile, mullite and ferrites.

Jul 1, 1955

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. John Birkinbine, J. E. Johnson, Jr., J. S. Unger, William H. Blauvelt, William Kelly, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. A. A. Stevenson, J. S. Unger and C. F. W. Rys have accepted membership on the Iron and Steel Committee. The Program Committee has held two meetings- in New York and has perfected the preliminary plans for the October meeting. The Committee will meet again in September. The following provisional program has been laid out by the Program Committee, but is subject to later additions and changes :

Jan 9, 1913

Dump Truck Kenworth Motor Truck Corp. is beginning full scale production of its new heavy-duty, end-dump earth mover, model 801, a truck engineered for earth moving under the most adverse operating conditions. Payload capacity of the Kenworth earthmover is 30,000 lb and it is over-tired for safety, flotation and high tire life. The truck's body capacity, struck measure, is 9.9 cu yd, with heaped [ ] load at 11.9 cu yd. The earth-mover has a full anti-friction bearing mounted, power assisted steering gear, simplified controls, minimum turning radius and wide axle track to insure ease of handling, maximum maneuverability and high stability. The offset cab of the Kenworth visibility for the driver, before and after. Circle No. 1 Safety Equipment A compact, safe, and efficient valve assembly approved by the United States Bureau of Mines for use with MSA air line respirators, abrasive masks, and abrasive helmets has been developed by Mine Safety Appliances Co. The new MSA continuous air flow control valve regulates air flow from a compressed air source to an operator using respiratory protective air line equipment. Three parts-a centridge container, a cartridge and the air flow check valve-comprise the entire assembly of the control valve. A position action adjustment knob on the cartridge container regulates the amount of air flowing to the operator. The valve can be detached from the air line instantly by pressing the trigger on the cartridge container near the check valve. As the trigger detaches the hose, the spring loaded ball-type valve, which is attached to the end of the hose, automatically stops the flow of air. Circle No. 2

Jan 1, 1952

By C. Richard Tinsley

Non-ferrous econometric metal models available from consultants are reviewed for structure and computer access, using copper as an example The evolution of a computerized metals price forecasting system for a consumer of non-ferrous metals is outlined including front ends, bridge equations, and supporting databases. An empirical sensitivity analysis technique is described. A postscript discusses the subscription costs of these models.

Jan 1, 1977

By Donald W. Jenkinson

Many types of gravity concentration equipment have been employed throughout the years since beneficiation of materials has been practiced. These include jigs, concentrating tables, vanners, sluice boxes, heavy media cyclones, and static heavy media separators or sink-float separators. In the beneficiation of coarse aggregate for concrete mixes, static heavy media separation employs the same principles of gravity concentration involved in separating lead-zinc ore, dolomite, limestone, diamonds, manganese, iron, and many other minerals. In aggregate beneficiation, as in most metallurgical operations, sink or heavy fraction is the product. The undesirable portion of coarse gravel is usually much lighter than the desirable particles, allowing most aggregates to be amenable to gravity concentration methods.

Jan 7, 1960

By K. R. Weller

The Ardlethan Tin Ltd. concentrator typically recovers 55% of the tin in a gravity concentrate at 51% grade from fresh ore assaying 0.5% Sn. Coarse gravity concentration is performed in a complex circuit involving Reichert cones, spirals, shaking tables and two regrind mills. The paper describes how flow and size-by-size sample data from a steady-state survey were used to construct a computer model of the plant involving 46 process streams. The data reduction involved a computer- aided mass balancing technique, recovery-size modelling of gravity concentrators and the use of a mineral dressing flowsheet simulator. The model was used to simulate possible rearrangements of the available equipment. Early simulations indicated that improved performance could be obtained by using spirals to-treat cone middlings or tailings rather than cone concentrates. A test spiral rig was used at Ardlethan to determine typical performances for all cone product streams and the results were incorporated in new simulations. A revised circuit was recommended and implemented by Ardlethan Tin as far as physical restraints within the plant would allow. Production figures show that a substantial increase in tin recovery and 10-15% increase in milling rate were achieved following the circuit changes, and these improvements were sustained over a six month period.

Jan 1, 1984

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923