Search Documents

By Fred W. Shultz

The process engineer is familiar with the in any methods employed in the past for analyzing various materials. These include panning. eyeballing, and wet chemistry. Of those mentioned only wet chemistry has been and will continue to be a standard measure for the elemental content in a given material. However, wet chemistry, by the very nature of the method, can be excessively time-consuming and thus reducing obviously the number of samples that may be processed in a given period. The analysis by X-ray, in most cases, requires nothing more than assurance that the sample is in a suitable state for presentation to the X-ray spectrometer.

Jan 1, 1964

By L. F. Mashburn, T. J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank- run gravels averages about 0.1 g/t-about $1.29/t, based upon $12.86/g ($400 per oz) gold. The fineness of the gold averages between 950 and 960. The Reichert cone, in conjunction with a conventional shaking table, recovers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1 % is - 74pm (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1983

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By C. P. Parsons

CALIPER logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork.

Jan 1, 1942

By William D. Schwab

In the technical literature of 1965 and 1966, there were several papers about future power for mining and construction equipment. Most of these papers made the same predictions: •More power •Better reliability and durability •Ease of service and maintenance •Operating economy •The possibility of future environmental concern •The entrance of the gas turbine In the five years that have since passed, some of the 1965-66 predictions have at least partially come true, while others have not been fully realized. Actually the list still appears sound today. Priorities may have changed and details may be different, but the main points cover the requirements for future prime movers quite well.

Jan 1, 1971

By S. L. Crouch

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By Kalanadh V. S. Sastry, D. W. Fuerstenau

A locked-cycle balling procedure has been designed to simulate continuous, closed- circuit balling drum operation in the laboratory. By this method, it is possible to simulate the surging in green-ball production rate and circulating load that is experienced in industrial balling circuits. Through an investigation of the effect of feed rate on the stability of the locked-cycle, balling process, it was found that higher feed rates lead to increasing instability in the process. An analysis of the experimental ,results is presented and the utility of the locked-cycle experimental technique for evaluating the stability of an industrial balling drum operation is discussed.

Jan 1, 1976

By R. R. Klimpel Discussion by C. C. Harris, L. G. Austin

C. C. Harris (Columbia University) — The authors ' have presented relationships for the random division of a magnitude into r + l parts taking account of the order of selection. Interpreting their model in comminution terms, their Eqs. 7, 9 and 11 refer to the one-dimensional case; that is, to the subdivision of a long thin rod at random. It is assumed that the fragments may be indefinitely small. Real materials, however, are limited in the degree of subdivision which can be attained through the intervention of practical restrictions. One in fine grinding is the depletion of microflaws as material becomes finer. Another is the

Jan 1, 1969

Low metal prices prevailing at the beginning of 1950 stimulated the search for improved mining methods. More experience was gained during the year with such new developments as the jackleg drill, millisecond delays as applied underground, trackless mining, and Diesel powered equipment. One of the outstanding innovations in mining practice was the starting of the Round Mountain "dry land gold dredging operation." The Government is now inviting the mining industry to open up every available source of new metal supply and this circumstance will undoubtedly speed the development of new machines. New methods will also result but it is doubtful if economic efficiency will be at its peak.

Jan 2, 1951

By S. J. Sindeband

Prior to discussing the metallurgy of sintered chromium borides, it is pertinent to outline some of the reasoning behind this investigation and the purposes underlying the work. This study was initiated as an aproach to the ubiquitous problem of a material for service at high temperatures under oxidizing atmospheres, and it was undertaken with a view to raising the 1500°F (816°C) ceiling to 2000°F (1093°C) or better. For the reason that no small, but rather a major, lifting of the high temperature working limit was being attempted, it was felt appropriate that a completely new approach be taken to this problem. A summary of the thinking behind this approach was published recently by Schwarzkopf.' In briefest terms, it was postulated that the following requirements could be set up for a material which would have high strength at high temperatures. 1. The individual crystals of the material must exhibit high strength interatomic bonds. This automatically leads to consideration of highly refractory materials, since their high energy requirements for melting are related to the strength of their atom-to-atom bonds. 2. On the polycrystalline basis, high boundary strength, superimposed on the above consideration, would also be a necessity. Since this implies control of boundary conditions, the powder metallurgy approach would hold considerable promise. Such materials actually had been fabricated for a number of years, and the cemented carbide is the best example of these. Here a highly refractory crystal was carefully bonded and resulted in a material of extremely high strength. That this strength was maintained at high temperature is exhibited by the ability of the cemented carbide tool to hold an edge for extended periods of heavy service. Nowick and Machlin2,3 have analytically approached the problem of creep and stress-rupture properties at high temperature and developed procedures whereby these properties can be approximately predicted from the room temperature physical constants of a material. The most important single constant in the provision of high temperature strength and creep resistance is shown to be the Modulus of Rigidity. On this basis, they proposed that a fertile field for investigation would be that of materials similar to cemented carbides, which have Moduli of Rigidity that are among the highest recorded. The cemented carbide, however, does not have good corrosion resistance in oxidizing atmospheres and without protection could not be used in gas turbines and similar pieces of equipment. It would be necessary then to attempt the fabrication of an allied material based upon a hard crystal which had good corrosion resistance as well. It was upon these premises that the subject study was undertaken and at an early stage it was sponsored by the U.S. Navy, Office of Naval Research. Since then, it has been carried on under contract with this agency. Chromium boride provided a logical starting point for such research, since it was relatively hard, exhibited good corrosion resistance, and, in addition, was commercially available, since it had found application in hard-surfacing alloys with iron and nickel. That chromium boride did not provide a material that met the ultimate aim of the study results from factors which are subsequently discussed. This, however, does not detract from the basis on which the study was conceived, nor from the value of reporting the results which follow. Chromium Boride While work on chromium boride proper dates back to Moissan,4 there has been a dearth of literature on borides since 1906. Subsequent to Moissan, principal investigators of chromium boride were Tucker and Moody,5 Wede-kind and Fetzer,6 du Jassoneix,7,8,9 and Andrieux." These investigators were generally limited to studies of methods of producing chromium boride and detennining its properties. Some study, however, was devoted to the chromium-boron system by du Jassoneix,7 who did this chemically and metal-lographically. This system is not amenable to normal methods of analysis by virtue of the refractory nature of the alloys involved, and the difficulties of measurement and control of temperature conditions in their range. Dilatometric apparatus is nonexistent for operation at these temperatures. Du Jassoneix made use of apparent chemical differences between two phases observed under the microscope and reported the existence of two definite compounds, namely: Cr3B2 and CrB. These two compounds, he reported, had quite similar chemical characteristics, but were sufficiently different to enable him to separate them. The easiest method for producing chromium boride is apparently the thermite process, first applied by Wede-

Jan 1, 1950

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,',' but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,' Roy et al., Zen\ and Hawkins.' One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)'" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed&apos; that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-&apos; it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3&apos; of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

By Whitman E. Brown, Louis J. Erck

L. A. ROE*—This paper is one of great value to the iron ore industry. The Humphreys spiral is a relatively new tool and gives promise of being quite useful in solving certain problems of iron ore beneficiation. Spirals have been tested on a martite ore at the Benson mine of Jones and Laughlin Steel Corp. in northern New York State. Our New York ore is considerably different, physically and mineralogically, than the one mentioned in this paper, and contains only 25 pct iron. This ore can be processed on spirals to give a concentrate containing 62 pct iron with an 85 pct recovery. On our particular ore we found operating difficulties when the spiral feed was coarser than 14 mesh. These were chiefly due to excessive "build-up" of locked middlings in the spiral circuit. In extreme cases these middling particles would accumulate to such an extent that the plant had to be shut down and the spiral surge tanks cleaned out. It is interesting to note that there exists a close relationship between the results of tabling a given iron ore and concentration of this same ore on Humphreys spirals. The size range of the ore must, of course, be within those limits acceptable to spiral concentration. Comparative tests on several of our mar-tite ores showed tabling results to be the same as spiral results. The authors make no mention of the use of a tailing stream splitter (now available from the spiral manufacturer) which is a useful tool in studying iron losses in the tailings stream. 011 our particular martite ore we found a considerable accumulation of fine-sized iron ore particles in the outside portion of the tailings stream. This fraction may be amenable to further treatment. E. H. ROSE*—The authors have concluded an interesting piece of work and this paper is an excellent factual account of a rapid and somewhat unusual transi-;ion in practice in the plant described. Perhaps it was modesty on their part which caused them so casually to limit to one sentence the fact that "several other methods of concentration on the fine ores representative of the Hill Trumbull group . . . failed to produce consistently an acceptable grade and recovery of finished product." The fact is that they were confronted by a difficult mineral-dressing problem and they are to be congratulated on their courage and persistence in staying with it until a satisfactory solution was evolved. A visitor to the plant might have been mildly astonished, as I was, to see one type of concentrator handling that part of the load early in the 1947 season, its experimental replacement by another a little later, and then in 1948 to see that both types had simply disappeared and their place taken by the spirals which were operating as placidly as though they had been there all the time. In working out economic methods of beneficiating Alabama red ore, most of which development is still ahead of us, it is likely that we also will pass through a period of successive disappointments, for we too have a problem where it is next to impossible either to "guess &apos;end right in the first place," or, because full-scale operating cost is such an important factor, to lay the ultimate answer on the line in advance by means of laboratory experimentation. Iron ore being what it is instead of what it used to be, it is encouraging to have the example the authors have given us today that a tough nut that will not crack on the first blow or the second is apt to do so on the third or fourth.

Jan 1, 1950

By Fredrick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C&apos;, D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C&apos;, 70 ft.; C&apos; to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By Albert Brown, Emil R. Ermert, Fredrick C. Pearson

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By G. K. Manning, W. E. Few

T has been known for some time that both&apos;inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham&apos; indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer&apos; have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker&apos; obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.&apos; Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951