Search Documents

By H. S. Munroe

The accompanying figures illustrate the dumping-device used at the new dressing works of the St. Joseph Lead Co., at Bonne Terre, Mo. It is a dumping-cradle, of a type much used abroad, in which the car is turned upside down to discharge its load. The main

Jan 1, 1889

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By L. W. Fagg

The purpose of this paper is to present in a convenient form data and examples necessary in making dynamometer card analyses; also to outline a procedure of well weighing. Many articles and papers have been written delving into the mathematical considerations relative to the shape and characteristics of dynamometer cards. However. it is recognized that there are too many unknown factors involved in such calculations to assure a workable degree of accuracy. For this reason the accepted procedure is to take dynamometer cards on wells in question rather than try to calculate the load curve. The polished rod dynamometer is now recognized as a necessary tool for measuring loads, torque, and horsepower. It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition. The apparently infinite variety of a = maximum load (height x scale constant) b = minimum load. Range of load is difference between maximum and minimum load speed—taken with stop watch stroke —measured at polished rod c = beginning of down stroke in direction of arrow. (End of up stroke) d = beginning of up stroke. (End of down stroke). Polished Rod Horsepower = (Area of card) x Scale const. x Stroke x Length x spm (Length of card) 33000x 12 1.35 1.35------x5300x 24 x 12 2.53 --------------------------= 2.06 23000x12 Appraximate Peak Torque: Upstroke = (2390) (12) (1) = 28,700 in. Ib Downstroke = (1 860) (12) (.866) = 19,300 in. Ib Counterbalance should be increased to make up stroke and down stroke peak torque equal. FIG. 1 dynamometer cards that can be obtained is one reason for the general lack of usage of the dynamometer as a control instrument rather than a means for making routine measurements of leads and horsepower. When it is considered that the dynamometer card is a record of the resultant of all forces acting on the polished rod at any particular instant during the pumping stroke. the problem is then one of breaking down this resultant into its various components. As a means of a quick review we shall consider the examples shown in Figs. 1 to 9: and Tables I and II and then proceed to the interpretation of variously shaped cards caused by some abnormal operating condition. In Table 11, when we were considering the factors involved in calculating the peak polished rod load, it can be seen that the factors involved greatly oversimplify the problem. Certain assumptions are made which may or may not he even close to the actual field conditions, such as the specific gravity of the fluid generally considered as one; that the crank has constant angular velocity; that the down-hole friction is zero; and that the fluid lift is from the pump. In the following examples we shall see what a variation in fluid weight and friction can do to the general shape and magnitude of the dynamometer card. (Figs. 10 to 22.) MAKING THE WELL STUDY It is obvious that it would be impractical to consider in detail all of these factors each time a well study is made, inasmuch as each well study job could conceivably be extended into a research project rather than serve the practical requirements of finding the answer to a specific problem. For this reason it is important that some objective be established previous to the time the well study is made. Load at TU = 3070 Ib Crank angle when polished rod is at position TU = ? ? = 30° Maximum counterbalance effect at polished rod = 2760 Ib Torque at TU = (Load at TU — Max. counterbalance effect-lbs) sin 0 x Length of Stroke 2 = (3070-2760) .5 x 24 = 1860 in. 15 2 Torque at TD = (Load at TD — Max. counterbalance effect-lbs) sin ? x Length of Stroke 2 = (530 - 2760) sin 330' x 24 = 13,400 in. Ib 2 Note: sin 0 from c to d on UPSTROKE will be positive value. sin 0 from c to d on DOWNSTROKE will be negative value Torque at c and d is zero because 0 is zero. FIG. 2 —APPROXIMATE METHOD FOR CALCUlATlNG TORQUE

Jan 1, 1950

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.' Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:' Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy' presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. 'References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,' and Carter et a1.' treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy's law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

By Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (I), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profit- ability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus mini- mum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12 ) Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-low- grade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1985

By R. E. Shinkosk

This paper outlines the development of a program for increasing the life of woolen bags used for filtering Dwight-Lloyd gases by treating the bags and gases with hydrated lime. Methods and apparatus are described for determining alkalinity of dusts, acidity and breaking strength of bag cloth. Procedure and results, based on several years of operation, are presented. DURING 1939, additional facilities were constructed in the Dwight-Lloyd Blast Furnace and Baghouse departments at the Selby, California, Plant of the American Smelting and Refining Co. In order to handle adequately the increased volume of gases from the resultant increase in production, it was necessary to increase gradually the amount of water used for cooling gases ahead of the sinter machine baghouse. As a result of this increased water cooling, the average bag life dropped from 27 months in 1939 to 14 months in 1941. (Table I). This drop in life meant an increased. bag cost, as well as lower recovery of dust and some curtailment of operation. During 1941, it was found new bags showed as high as 0.3 pct acidity* after two weeks of opera- tion and as much as 2.0 pct acidity after some months of operation. This high acidity was present in spite of the fact that free oxide or relative alkalinity of the unburned dust ran from 5 to 6 pct. In view of these circumstances, a twofold program was started in Nov. 1941.t Part one of this program consisted of vigorously dipping all new bags in a weak lime solution, containing 50 lb of hydrated lime per 50 gal of water. Part two consisted of feeding fine, dry, hydrated lime into the gas stream intake of the sinter baghouse fan. Apparatus for feeding this lime is shown in fig. 1. All baghouse chambers are shaken in rotation about once each hour. On alternate hours, the baghouse operator places 50 lb of hydrated lime (one sack) into the lime feeder, starts feeder and immediately starts the bag shaking machinery. The rate at which lime is fed is set to coincide with the approximate time necessary to shake all sinter bag-house chambers, or about 15 min. It is felt this method of lime addition is most effective for getting lime into the woolen bag fabric. The amount of lime so fed averages about 600 lb per day. The amount of lime fed per day is varied to keep a minimum relative alkalinity of 9 pct in the unburned sinter dust. A daily dust sample is taken for alkalinity by allowing dust to accumulate in a sample pipe over a 24-hr period. This sample pipe, placed in any chamber cellar, is 2 in. in diam, 4 ft long, is sealed on the inner end, and capped on the outer end. It has a 1/2 in. slot cut for 18 in. along the tip end. This slot faces upward and allows the pipe to fill gradually with dust as bags are shaken. Breaking strength of bags has, in most cases, been the deciding factor in bag replacement. Bags that normally test 100 psi breaking strength when new are replaced when they test under 35 lb. The method for determining breaking strength is shown in the description accompanying fig. 2. Since the start of the liming program in 1941, bag life has increased from 14 months to an average of over 23 months, with a consequent material decrease in bag cost per year. Acidity, as per cent sulphuric acid, may be determined by means of a Beckman pH meter as follows: From a piece of bag cloth. which has been thoroughly cleaned of dust, a 5 g sample is weighed on a balance. Cut the sample into fine pieces and place in a 400 cc beaker. Add 100 cc (measured) of distilled water and stir vigorously. Filter on suction funnel, holding cloth pulp in beaker with a stirring rod. Wash cloth sample and filter wash water four additional times, each time with 20 cc distilled water, the last time squeezing cloth pulp over funnel. Discard pulp and rinse funnel and filter paper. Pour wash solution jnto measuring graduate and make up to exactly 300 cc with distilled water. Place into clean 600 cc beaker and measure the pH on meter. The per cent acid in bag cloth is read from the following table:—

Jan 1, 1951

By T. I. Moore, L. A. Painter

THE electrolytic zinc plant of the American Zinc Co. of Illinois was described by Davidson' in 1944. Since then, improvements as well as expansion of the plant facilities have been made. In order to increase the production of high grade zinc which was needed for war purposes, an expansion program designed to double the slab zinc capacity was started in 1942 and completed in March 1943. This expansion was propagated by a contract between the American Zinc Co. of Ill. and the Defense Plant Corp. The contract included the facilities of the Fairmont City, Ill., property of the American Zinc Co., where a suspension-type roaster with contact acid plant, cadmium distillation furnace, Waelz oxide and densifying plant, and horizontal retort furnaces were installed. The expanded Monsanto, Ill., plant and the additional facilities of' the Fairmont plant were designed to integrate the metallurgical treatment of zinc concentrates for the production of special high grade zinc at Monsanto with the production of acid, cadmium, high grade zinc from furnace skimmings and the Waelz treatment of leach residue at Fairmont. In general, the original flowsheet was not changed, except for the addition of the filtering, drying and reclaiming of leach residue, and the treatment of purification cake for the recovery of copper, cadmium sponge, and zinc. Fig. 1 is a flow diagram of present operations. The original plant facilities, desi-gned for 50 tons daily production of slab zinc, had some units which were more than adequate. Therefore, in expanding the facilities to 100 tons per day, it was not necessary to double all operating components. Table I gives the comparison of the changes made in the unit operating components for the original facilities, 1941, the 1943 expansion, and the 1951 facilities. During the past 11 years a number of improvenients have been made resulting in: 1—an increase in slab production, 2—higher recoveries on the calcine treated, 3—better quality of slab zinc produced, 4—higher current efficiencies, and 5—less man hours Table I. Changes in Operating Facilities Operating Unit 1941 1943 1951 Calcine unloading (pneumatic), 10 tons per hr 12 calcine unloading track hpr. and elev., 60 tons per hr 1 Calcine storage, tons 1,000 2,000 2,000 Leach tanks, 35 vol. tons. No. 3 5 6 slurry mixing 6x6 ft stainless tank, No. 1 Ball mill. 4.5 rt x 16 in. conical. No. 1 CLassifier duplex, No. 1 1 Thickeners. 50 it diam. No. 2 9 2 Filter thickeners, sq ft '-- Moore filters, sq ft 5.760 11,520 Drum filters, 10 ft diam x 16 ft, No. 3 3 Rotary arlers, No. 1 2 1st stage Cu-As purificatlon tank. 90 vol. tons, No. 3 Solution heaters, No. 3 Filter press, 30x30 bronze, No. 4 Zinc dust purification tanks, 45 vol tons. No. 3 5 4 Filter press, 36x36 bronze, No. 3 5 3 Cadmium recovery plant: Process tank. No. 5 2 Cake roaster, 20 ft diam x 4 hearth. No. 1 Filter press, 24x24, No. 4 1 Sponge wash box, 4x6 ft, No. 1 Evaporative cooling unit (vacuum), No. 1 Purified storage tank, vol. tons 400 400 400 Cell acid storage, vol. tons 400 400 400 Electrolytic cells, No. 180 372 372 Cell room ventilation, cu ft per min 35,000 125,000 125,000 Cell cooling water. gal per min 1,500 2,300 2,300 Deep well 16 in. x 95 ft, 1500 gal per min, No. 2 3 3 Melting and casting furnace, 130 ton. No. I Furnace fume scrubber unit, No. 1 Dross drums, No. 2 Dross roaster, 8 ft diam x 8 hearth, No. 1 Electrolysis power conversion, kw 6,250 23,750 23,750 Power transformers, 13,800/440, kva 1,000 1,500 2,000 Steam boilers fire tube, 15 psi, lb per hr 12,000 18,000 18,000 Steam boilers water tube. 125 psi, Ib per hr 30,000 Air compressor, 2 stage. 300 cu ft per min. 100 psi, No. 1 2 Air compressor, 1 stage, 300 cu ft per min, 20 psi, No. 1 Vacuum pumps, 18x7, 720 cu ft per day, No. - - . Vacuum pumps, 24x11, 1.633 cu ft per day, No. 3 3 Building area, sq ft 60,854 113,568 115,000 per ton of metal produced. In the summer of 1944, the "reverse" leaching process was placed in operation and since it has been described,' no further description will be given. Other facilities and changes which have contributed to the process improvements were the scrubbing of fume from the melting and

Jan 1, 1953

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By E. D. Levine

A study was made to delineate the dislocation mechanistns controlling prismatic and basal slip at low temperatu.ves in titanium containing approximately 100 ppm interstitial impurities. Mechanical tests were performed on single crystals prepared from electron-beam zone-refined crystal bar by a thermal cycling technique. Measurements were made of critical shear stress and activation volume as functions of temperature. The study revealed that, for prismatic slip, two overlapping thermally activated processes aye rate-controlling below 300°K. From absolute zero to 220°K, reasonable agreement is obtained between experiment and the mechanism which involves overcoming 01. the Peierl's stress by the formation of double kinks in dislocation lines lying in close-packed directions. Between 220°and 300°K prismatic slip is controlled by a difierent thermally activated process which is characterized by a stronger temperature dependence of critical shear stress. Above 300OK, prismatic slip is controlled by an athermal process. Basal slip is controlled by a thermally activated process between 195' and 400°K. An approximate analysis suggests that it is the Peierl's mechanism that is rate-controlling in this range. Below 195°K, the occurrence of mechanical twinning obscures the features of basal slip. Above '400 X, basal slip is controlled by an athermal process. TITANIUM, an hcp metal with a less-than-ideal axial ratio of 1.587, deforms primarily by {1010}( 1210) slip at low temperatures.'-3 The critical shear stress is strongly affected by the presence of interstitial impurities. For example, churchman3 reported that a decrease in the combined nitrogen plus oxygen content from 0.1 to 0.01 pct decreased the critical shear stress for prismatic slip from 9.19 to 1.4 kg per sq mm at room temperature. Basal slip, however, is less strongly affected by interstitials; Churchman's data for {0001}( 1210) slip show a smaller decrease in critical shear stress from 10.90 to 6.3 kg per sq mm at room temperature, for the same decrease in interstitial content. In the present study, an attempt has been made to delineate the dislocation mechanisms controlling prismatic and basal slip in titanium. In view of the strong effects that impurities may have on at least some of these mechanisms, experiments were performed on material of reasonably high purity, so that comparisons could be made with investigations on material of both lower and higher impurity contents. EXPERIMENTAL PROCEDURE Single crystals were prepared from 1/4-in.-diam electron-beam zone-refined crystal bar, furnished by Materials Research Corp. The analysis of the zone-refined material is given in Table I, indicating that the interstitial content is of the same order as the purer of the two materials investigated by Churchman. The Vickers diamond pyramid hardness number of this material was 85.6. This value agrees quite well with the correlation between hardness and interstitial content proposed by Ogden and Jaffee.4 On the basis of hardness, the material investigated in this study is, therefore, intermediate in purity between that studied by Churchman (Vpn = 97) and that studied by Spangler and Herman (Vpn = 62.4).5 Single crystals were grown by thermal cycling through the a-ß transformation. Two-in.-long by 1/2-in.-diam bars were heat-treated in vacuum for 4 hr at 1160°C. The temperature of the furnace was then lowered to 865°C, and the specimens were maintained at this temperature for 7 days. This procedure was repeated several times, resulting in the growth of individual crystals up to 14 in. in length. Specimens for testing in direct shear along either {l010}(1210) or {0001}(1210) were obtained by electrical-discharge machining. The specimens were in the form of cylinders 1/4 in. in diam by approximately 1/2 in. in length, with a reduced section 1/8 in. in diam and a in. in length. All specimens were electropol-ished subsequent to electrical-discharge machining. The ends of the test specimens were cemented in stainless-steel collars. Shear tests were conducted in an Instron Tensile Tester at various temperatures from 4.2° to 508°K. Measurements were made of critical shear stress and activation volume. The latter measurements were performed by measuring the change in flow stress upon cycling the strain rate between ?1 = 2.62 x 10-3 per sec and ?2 = 2.62 x 10-4 per sec. Activation volume, I)*, is defined as u* =ßkT [11

Jan 1, 1967

By R. A. Wolfe, H. W. Paxton

Self-diffilsion coefficients for cr51 and Fe55 in 12 pct Cr-Fe and 17 pct Cr-Fe for Fe55 in chromium, and for Cr51 in vanadium have been measured. The results are compared with other values for the Fe-Cr system, and with the various theories of diffusion in hcc metals. Some empirical correlations are discussed between Do and Q in hcc systems, or, expressed differently, the constancy of ?G*/T solidus for seveval bcc metals and alloys is noted. It appears very probable that a vacancy mechanism is operative in bcc metals, hut this cannot he stated with certainty. THE great bulk of work on diffusion in metals, both experimental and theoretical, was for many years concentrated on those with close-packed and, in particular, fcc lattices.1,2 There appears to be little doubt that the mechanism of diffusion in these solids is vacancy migration, leading to mass transfer and in substitutional solid solutions to a Kirken-dall effect.3,4 For bcc metals, the picture is much less clear. The Kirkendall effect certainly occurs in several alloys.5-10 However, attempts to understand the factors contributing to the pre-exponential in the usual expression for the diffusion coefficient D =D, exp {-Q/RT) by extension of ideas useful in close-packed lattices have not always been successful. Zener,11 Leclaire,12 and Pound, Paxton, and Bitlerl3 have suggested that various forms of ring diffusion may be important in some bcc metals. For close-packed metals, Do is usually about 1 sq cm per sec and Q - 35Tm kcal per mole (Tm = melting temperature in OK). The theory of Pound et al. suggests for ring diffusion that Do may be about 10-4 and Q, although difficult to calculate with any precision, would be significantly less than 35 T,. The experimental results on self and solute diffusion in ? uranium14,15 and ß zirconium,10 and for solutes in 0 titanium,17 and possibly for self-diffu- sion in chromium below about 0.75 T,," gave some credence to this theory. However, not all bcc materials display low values of DO and Q, and the exceptions were not predicted by any theory. Furthermore, it has recently become apparent that, in bcc materials, log D is not always linear with T-l if a sufficiently wide range of temperature is studied.16,18 This variation may be such that Q may increase18,19 or decrease20 with increasing temperature. The present work was undertaken in an attempt to provide further diffusion data on bcc metals, and to try to understand the factors which contribute to differences in behavior between the various elements. For part of this work, the Fe-Cr system was chosen since it is of considerable technological importance, and data on 12 pct Cr and 17 pct Cr alloys appeared well worthwhile to supplement that existing for the remainder of the stern.18,22 The diffusion of Fe55 in chromium was studied as an example of a more or less "normal" tracer element in a possibly abnormal host lattice. Finally, no data were available for vanadium, the neighbor of chromium in the periodic table, because of lack of a suitable isotope so cr55 was used as a tracer in a few preliminary experiments. For convenience, we shall refer to elements whose Do and Q are low compared to those predicted by Zener's theory as "anomalous". PROCEDURE This investigation determined self-diffusion rates by means of radioactive tracers and the integral-activity method first utilized by Gruzin.23 In this method a thin layer of radioisotope of the diffusing element is plated or coated onto a planar surface of the diffusion sample, which is then given an isothermal-diffusion annealing treatment. The determination of an activity-penetration curve involves measuring the residual activity of the specimen after each successive layer or section has been removed parallel to the original planar surface. The method used here is essentially the same as that used by Gondolf18 and Kunitake.21 Two radioactive tracers, cr51 and Fe55, were used in this investigation. Diffusion coefficients were determined for the diffusion of one or both of these tracers in four different materials, viz., Fe-12 wt pct Cr alloy, Fe-17 wt pct Cr alloy, chromium, and vanadium. The diffusion samples had nominal dimensions of 1.5 cm diameter and 0.5 cm thickness. The grain size was several millimeters for the Fe-Cr alloys and at least 1 mm for the chromium and vanadium samples. Accurately planar surfaces

Jan 1, 1964

By A. B. Bowman

The 1963 Jackling Award lecturer describes the founding of Banner Mining Co. and its trials and tribulations before becoming an established firm. Such aspects as geological description of Banner mining areas, history of exploration and production, areas of present interest to the company and research work conducted by the company are included. Several years ago a wealthy Chinese business friend of mine purchased an interest in a proposed oil well to be drilled a great distance from his home. A few months later it came in as a producer and proved to be a huge success and materially added to his resources. I asked him why a man of his wealth should be so lucky in a venture outside his sphere of knowledge when most people of modest means never seemed to get ahead. His answer was, "Fat Hoy takes a chance." Even though this was his answer, I knew from my association with him that there were other tempering considerations which Mr. Hoy applied before making up his mind to enter any transaction. First, he was a cautious individual. He was also a great believer in details and insisted on knowing everything possible about a situation, and finally, he was what we call a very solid individual with good basic instincts and judgment. This philosophy of Mr. Hoy may be applied to most any business but especially to those engaged in a search for natural resources such as mining where great risks are involved. This article concerns events in the history and growth of Banner Mining Co., with which I have been associated for 27 years in capacities from mine surveyor to vice president. Mr. Hoy's philosophy has played a significant role in the exploration projects of this company over the years, but what is more important, the officers, directors, and controlling interests in Banner have been aggressive in their search for ore reserves. THE BIRTH OF BANNER Banner Mining Company was incorporated in September 1935 by a group of Oklahoma and Texas oil men for the purpose of exploring and developing the Bonney-Manilla mines at Lordsburg, N.M. These properties had a history of intermittent production since the first ore discoveries as far back as 1870. Most of the production from the district has come from four mines, namely, the Eighty-Five, the Atwood, the Bonney-Manilla, and the Misers Chest. The last two are now owned by Banner Mining. The Eighty-Five mine operated between 1885 and 1931, and production totalled 1,494,287 tons averaging 0.11 oz of gold per ton, 1.23 oz of silver per ton, and 2.80% copper. The vein extended for a distance of about 3000 ft northeast and was mined to a depth of 1650 ft. The Atwood mine, adjoining the Eighty-Five mine, to date has been of lesser importance as a producer, but it has been operating for several years producing high silica flux ores for a smelter. Production totalled 352,828 tons up to January 1, 1962 From the Bonney-Manilla and Misers Chest mines, owned by Banner, production through 1961 totalled 2,006,343 tons with an average grade as mined of 0.0192 oz of gold per ton, 0.760 oz of silver per ton and 2.63% copper. Banner built a 150-tpd flotation mill in 1936 after almost a year of development on the 600 level of the Bonney mine. After less than one year's operation, it became apparent that the 150-tpd rate was not sufficient to make a reasonable profit due to the marginal grade ores. The low tenor of the ore, mainly chalco-pyrite in a highly siliceous gangue, made mandatory the close control of costs in order to make ends meet. A 300-tpd unit was added to the mill in 1937, and it is still the operating unit today. The clean sulfides presented no problems in milling. A metallurgist doing research on it at the time stated that the copper minerals seemed to have a built-in desire to float. Mill recovery of copper throughout the 27 years of operation has averaged 96.23%. A PERIOD OF FORCED GROWTH World War II brought many hardships to Banner. Labor and supply shortages caused drastic curtailment in development work. Rapidly rising costs far outdistanced any relief from pegged prices which we received from Government agencies. Finally, a branch of the Government asked us to stop all devel-

Jan 1, 1963

By W. C. Maurer

A study of bit-tooth penetration, or crater forniation. under simulated borehole condirions has been made. Pressure conditions existing when drilling with air, water and mud have been sirnulated for depths of 0 to 20.000 ft. These crater tests showed that a threshold bit-tooth force must he exceeded before a crater is .formed. This thresh old force increased with both tooth dullness and diflerenrial pressure between the borehole and formalion fluids. At low differential pressures, the craters formed in a brittle manner and the cuttings were easily removed. At high differenlial pressures, the cunings were firmly held in the craters and the craters were formed by a pseudoplas-tic mechanism. With constant farce of 6,500 16 applied to the bit reeth, an increase in differential pressure (sitnulated mud drilling) from 0 to 5,000 psi reduced the crater volumes by 90 per cent. A comparable increase in hydrostatic fluid pressure (simulated water drilling) produced only a 50 per cent decrease in volutne while changes in overburden pressure (simulated air drilling) had no detectable effect on crater volume. Crater tests in unconsolidated sand subjected to differential pressure showed that high friction was present in the sand at high pressures. Similar friction belween the cuttings in craters produces the transition from brittle to pseudo plastic craters. INTRODUCTION The number of wells drilled below 15,000 ft increased from 5 in 1950 to 308 in 1964. Associated with these deep wells are low drilling rates and high costs. High bottom-hole pressures produce low drilling rates by increasing rock strength and by creating bottom-hole cleaning problems. This paper describes an experimental investigation of crater formation under bottom-hole conditions simulating air, water and mud drilling. Although numerous investigators have studied bit-tooth penetration (cratering) at atmospheric pressure conditions, only limited work has been done on cratering in rocks subjected to pressures existing in oil wells. Payne and Chippendale2 have studied cratering in rocks subjected to hydrostatic pressure using spherical penetrators. Garner et aLJ conducted crater tests in dry limestone by varying overburden pressure and borehole fluid pressure independently and using atmospheric formation-fluid pressure Gnirk and Cheathem4,5 have studied crater formation in several dry rocks subjected to equal overburden and borehole pressure and atmospheric formotion pressure. Podio and Gray studied the effect of pore fluid viscosity on crater formation using atmospheric borehole and formation-fluid pressurc and varying overburden pressure. Although these studies have provided useful information on crater formation under pressure, they were limited in that the three bottom-hole pressures could not be varied independently and, therefore, that many drilling conditions could not be simulated. The prersure chamber used in this study allowed visual observation of the cratering mechanism and independent control of the borehole, formation and confining pressures. By using different fluids in the chamber, pressure conditions existing in air, water and mud drilling to depths of 20,000 ft were simulated. The mechanisms involved in cratering at these different pressure conditions were studied for teeth of varying dullness and at different loadins rates. High-speed movies (8,000 frames/sec) and closed-circuit television were used to visually study the crater mechanism under pressure. EXPERIMENTAT PROCEDURE PRESSURE CHAMBER The Pressure chamber in Fig. I was used to simulate bottom-hole pressure conditions. This chamber has been pressure-tested to 22,500 psi and is normally operated at pressures up to 15,000 psi. The chamber contains four lucite windows' used for illuminating and observing the crater mechanism under pressurc. A closed-circuit television and a Fastax camera (8,000 frames/sec) have been used in these studies. Cylindrical rock specimens (8-in. diameter X 6-in. long) were subjected to three independently controlled pressures simulating overburden, borehole fluid and formation-fluid pressures. Overburden pressure, which corresponds to the stress induced by the overlying earth mass, was applied by exerting fluid pressure against a rubber sleeve surrounding the rock. Borehole pressure, which is the pressure exerted by the column of mud in the wellbore, was simulated by applying pressure to the fluid overlying the rock in the chamber. Formation pressure was simulated by applying pressure to the water saturating the rock. The borehole and formation pressures were equal except when mud was used in the chamber, in which case the differential pressure between these fluids acted across the mud filter cake.

Jan 1, 1966

By H. E. Mauck

The many factors that control bumping must be carefully studied for each coal seam where bumps occur, and specifications known to exclude bumping should be incorporated in the mining plans. This calls for complete knowledge of the seam's characteristics and its adjacent strata, and in many instances these characteristics are not revealed until the seam is actually mined. Pressure and shock bumps, the two general types, occur jointly and separately. In this discussion no differentiation will be made. Whether pressure or shock, they are treated as bumps, and both must be eliminated. Bumps in mines have occurred in several places throughout the coal fields of the world. A study of many of these occurrences indicates that geologic characteristics, development planning, and mining procedure have contributed. But more specifically, there are conditions usually associated with bumps: thickness of cover, strong strata directly on or above the seam, a tough floor or bottom not subject to heaving, mountainous terrain, stressed and steeply pitching beds, and the proximity of faults and other geologic structures. Mine planning should incorporate these known factors (not necessarily in order of importance): 1) Main panel entries should be limited to those absolutely necessary to ventilate and serve the mine. This reduces the span over which stresses may be set up that will later throw excessive pressures on barrier and chain pillars when they are being removed. 2) Barrier pillars should be as wide as practicable so that they will be strong enough to carry the loads thrown on them when final mining is being carried out. 3) Pillars should never be fully recovered on both sides of a main entry development if the barrier and chain pillars are to be removed later. The excessive pressures placed on the main chain and pillar barriers by arching of the gob areas can result in bumping when these barriers are being removed. 4) Full seam extraction is better accomplished by driving to the mine boundary and then retreat-drawing all pillars. If there are natural boundaries in the mine—such as faults, want areas, and valleys —retreat should be started there. 5) Pillars should be uniform in size and shape. The entire development of the mine should call for uniform blocks with entries driven parallel and perpendicular. Only angle break-throughs should be driven when necessary for haulage, etc. 6) For better distribution of rock stresses and reduction of carrying loads per unit area, both chain and barrier pillars should be developed with the maximum dimensions. 7) Pillars should be open-ended when recovered. If they are oblong, the short side should be mined first. Both sides of a block should not be mined simultaneously, but under no circumstance should the lifts be cut together. 8) Pillar sprags should not be left in mining. If they are not recoverable, they should be rendered incapable of carrying loads. 9) Pillar lines should be as short as practicable. (Three or four blocks are adequate). Experience has shown that rooms should be driven up and retreated immediately. The longer a room stands, the more unfavorable the mining conditions. This contributes to bumping. 10) Pillars should not be split in abutment zones (high stress areas lying close to mined out areas) and if slabbing is necessary, it should be open-ended. 11) Pillars should be recovered in a straight line. Irregular pillar lines will allow excessive pressures thrown on the jutting points. Experience has shown that the lead end of the pillar line can be slightly in advance. 12) Pillar lines should be extracted as rapidly as possible. This appears to lessen pressures on the line and render abutment zones less hazardous. 13) Extraction planning should call for large, continuous robbed out areas. Robbing out an area too narrow to get a major fall of the strata above the seam tends to throw excessive pressures on a pillar line. 14) Timbering in pillar areas should be adequate but not excessive. Too heavy timbering or cribbing is likely to retard roof falls and throw excessive weight on the pillar line. 15) Experience has shown that when pillar lines have retreated 800 to 1000 ft from the solid, bumps can occur. Because this distance may vary in different seams, impact stresses should be studied for each individual condition. In any event, extra precautions should be taken against bumps in this area. This list of controlling factors may or may not be complete. It probably is not, but it covers most of the problem's significant aspects. The question is whether or not bumping can be eliminated. The answer is that bumping can be minimized and possibly eliminated if these and other established factors are thoughtfully considered and incorporated in the mining and extraction plans. If a mine has already been developed or the pattern set so that little change can be made, then it will be necessary to adjust to the most nearly practicable system that can incorporate the known factors.

Jan 1, 1959

By Donald E. Meyer

High current-low voltage EB-gun evaporation in an oil-free ultra-high vacuum system was found to be necessary, though not sufficient, for stability (300°C, 106 v per on) of aluminium gate MOSFET's and MOS capacitors not stabilized by a phosphorous glaze. five characteristics of the equipment used: 1) Vacuum purification of the aluminum charge, 2) Ionization of the evaporant by the electron beam, 3) X-ray formation, 4) Residual gases during evaporation, and 5) Metal film structure were studied as Possibly significant in MOS fabrication. EVAPORATION of contact metals common to the semiconductor industry historically has been accomplished with oil diffusion pump systems and various resistance heated evaporant sources as dictated by the type of metal evaporated. To meet a need for greater reliability of semiconductor devices, other metallization methods were developed. A good example would be application of the moly-gold contact system to integrated circuits with deposition by RF or triode sputtering.' More recently, fabrication of stable metal-oxide-silicon devices and circuits has put new demands on metallization. The purity of the thin metal films composing MOS structures is critical, particularly at the metal-oxide interface, and ultra-high vacuum metallization using sputter-ion pumping and electron beam gun (EB-gun) evaporation are well suited for the task. At this laboratory aluminum has been the most common contact-gate metal for both MOS capacitors and MOSFET's. In the earliest work with MOS capacitors, aluminum was evaporated from wetted tungsten filaments using both diffusion pump and ion pump vacuum systems. In spite of clean oxide techniques these capacitors were unstable under bias-tempera-ture stressing. Only after a switch to EB evaporation of aluminum were stable capacitors produced. Using the same techniques it was possible to make MOSFET's with equivalent stability. Stability data for a discrete MOSFET is shown in Fig. 1. This is a "clean" oxide gate (no phosphorus stabilization or no etch back of a thicker gate) having a thickness of lOOO? thermally grown on the (111) plane. Gate length after diffusion was 0.24 mils, and the devices were hermetically sealed. Stressing conditions were 300°C and 106 v per cm applied alternately as a positive and negative field for 10 min, 50 min, and 4 hr for a total stress time of 10 hr. An initial shift in turn-on voltage of 0.1 v was detected for 10 min of positive bias. All evidence at this laboratory indicated that while EB-gun evaporation of ultra-high purity aluminum was not sufficient for 300°C stability, it did seem to be necessary. There may well then be something inherent in the EB-gun deposition used which enhanced stability, and probably no single factor existed but rather a series of factors. It is the purpose of this paper to report on some of the investigations carried out to learn more about EB-gun evaporation in ultra-high vacuum systems. EXPERIMENTAL DESCRIPTION The EB-gun was self accelerated, had a maximum power rating of 10 kw, and used a water-cooled copper crucible able to hold a 20-g aluminum charge. The electron beam was bent 180 deg and focused by an electromagnet which also provided movement of the beam across the crucible. Normal power conditions in this work were 9 kv and 300 to 600 mamp. The gun can be described as high-cur rent/low-voltage and was quite different in its mechanism of operation from EB-guns with much higher acceleration potentials. An oil-free vacuum system capable of 5 x 10- l0torr, a quartz crystal rate and thickness monitor and a quadruple mass spectrometer completed the evaporation system, Fig. 2. A typical evaporation cycle consisted of a 3 to 4 hr pumpdown to the upper l0-9 range and evaporation at l0? per sec with the pressure in the bell jar not rising above 1 x 10"7 torr. Thickness control was 5 pct or less and could be automatically monitored and controlled. Five phenomena associated with the EB evaporation and considered as possible contributors to Ma performance included a purification effect, ionization of evaporating aluminum, X-rays, constitution of vacuum ambient during evaporation, and film structure dependence upon evaporation rate. These phenomena are now discussed. Vacuum Purification. The design of the EB-gun permitted purification of the aluminum charge by vacuum outgassing. Particular features included an efficiently water-cooled copper hearth with a capacity of over 20 g of aluminum and the capability for sweeping the beam across the charge. Such capacity meant that aluminum had to be added only after about every fifth evaporation. A new charge was not required each evaporation as is necessary with filament evaporation. An oxide "scum" which appeared on the charge could be completely cleared from the top hemisphere of the charge by sweeping with the beam prior to opening the shutter. An indication of the purifying effect was obtained by a series of analytical measurements on incoming aluminum, after melting but with little vacuum out-gassing, after 30 min outgassing, and the evaporated film itself. Either a solids (spark source) mass spectrometer or an emission spectrometer were used for analyzing the aluminum charge. Analysis of the evapo-

Jan 1, 1970

By M. S. Seltzer

High temperature steady-state creep rates have been determined jor lead sulfide single crystals whose defect concentrations were fixed by equilibration under controlled sulfur pressure. The activation energy of creep, Qc , for undoped lead sulfide, is a function 01 composilion, decreasing from 2.9 to 2.2 ev as the carrier concentration increases from 9 x 1016 to 8 1018 electrons cm-3 for lead excess crystals, and increasing from 1.7 to 2.3 ev as the concentration of holes increases from 4 x 1017 to 1 x 1018 cm-3 in sulfur excess material. For five different composilions, Qc for undoped and bismuth-doped crystals has been found to be equal to Qpb + Qs, the self-diffusion activation energies for lead and sulfur in PbS. It is well-established1 that high-temperature steady-state creep of pure metals is a diffusion-controlled process, where the activation energy of creep is equal, within experimental error, to the activation energy of self-diffusion. The relationship between the activation energy for steady-state creep and those for self-diffusion in binary compounds is more complicated, however, because two different diffusing species must be considered, and becayse the activation energies may be influenced by compositional variations and by foreign atom additions.2-4 In some cases experimentally determined creep activation energies are correlated with those for self-diffusion of the slower-moving species, but such agreement is by no means universal. Interpretation of experimental results is difficult because few investigations include measurements of creep rates and self-diffusion coefficients of both diffusing species on single crystals of similar composition and foreign atom concentration. The objective of this investigation, therefore, is to determine the influence of stoichiometric defects and foreign atoms on steady-state creep and self-diffusion for a well-characterized binary compound. Lead sulfide, a compound semiconductor which crystallizes in the NaC1-type structure, and whose homogeneity range includes compositions on either side of the 1:l atom ratio, was chosen for study in this investigation. The pressure-temperature-composition relations for PbS are available,5,3 and deviations from stoichiometry may be monitored by electrical measurements.7 Single-crystal specimens are available to allow observation of effects due to bulk phenomena without interference from grain-boundary effects. These crystals have been employed to determine steady-state creep rates under compressive stress for "pure" and bismuth-doped PbS as a function of sulfur pressure and temperature as well as crystal orientation and applied stress in order to establish the relationships between defect concentrations and creep rates. EXPERIMENTAL PROCEDURES Crystal Growth. Lead sulfide crystals, prepared by the Bridgman method, are grown in evacuated quartz crucibles, filled with almost equal atomic proportions of high-purity (99.999 pct) lead and sulfur, and heated to a temperature above the melting point of PbS (about 1127°C) so that the lead and sulfur react to form molten PbS. The crucible and melt are dropped through the hot zone of the crystal-growing furnace at the rate of 1 cm per hr. The maximum melting point of PbS is slightly on the lead-rich side of the 50:50 composition; hence crystals grown from a near stoichiometric melt are usually n-type semiconductors containing excess lead atoms. Typically the lead excess concentration in solid solution with the PbS is 3 x 1018 atoms cm-3. Crystals containing either 1/20 or 1/2 mole pct Bi2S3 were prepared by addition of the foreign atoms prior to crystal synthesis. Preparation of Specimens of Controlled Stoichiom-etry. Since it is difficult to grow crystals of desired composition, the process of crystal growth and control of stoichiometry are separated into two distinct operations. Equilibration of as-grown PbS to a desired composition is most easily accomplished by first annealing the n-type crystals under high sulfur pressure (about 1 atm) at temperatures above 700°C. This process serves to put excess lead precipitates into solution, yielding 0 -type crystals upon quenching to room temperature. Inter diffusion occurs readily in crystals so treated, and the methods described by Bloem may then be employed to obtain crystals of controlled stoi-chiometry. For the creep measurements made in this study, this involves heating crystals in mixtures of H2 and H2S The equilibrium constant for H2S is given by: Thus the sulfur partial pressure is obtained from knowledge of the H2/H2S ratio and Kh2S for the temperature in question. Fig. 1 shows the p-T-x diagram for PbS. It can be seen that, within the stability limits for single-phase lead sulfide, desired compositions may be obtained by equilibrating under a specified sulfur pressure and temperature. Characterization of Crystals. The principal methods for evaluating PbS crystals include measurement of electrical properties and mass-spectrographic analysis. The measured electrical parameters include Hall coefficient, conductivity type, and electrical resistivity Bloem7 has shown that there is a 1:l relation between the defect concentration and carrier concentration obtained. Hence, if the contribution to the carrier con-

Jan 1, 1968

By Jose M. Sobral

Approximate figures for petroleum production in Argentina for 1929 show an increase of only about 300,000 bbl. over production for 1928. This increase is due to greater yield in the Plaza Huincul and in the Salta regions. Table 1 shows the distribution of production in the various fields of the whole country, using estimates for the later months of the year. The outlook for production remains about the same as in 1928. It is believed that in northern Argentina there are regions that contain oil, but they are yet unexplored. Notable traces of oil at depths between 1280 and 1390 m. have appeared in a 1500-m. boring in Comodoro Rivadavia, but their importance is unknown.

Jan 1, 1930

Committee of Arrangement E. P. MATHEWSON, Chairman. FRANK M. SMITH, Vice- Chairman D. C. BARD, Secretary, Montana State School of Mines, Butte, Mont. OSCAR ROHN, JAMES L. BRUCE. On Aug. 20, 1913, the following 30 members of the Institute residing in Montana made written application to the Board of Directors of the Institute for authority to establish a local section of the Institute to be called the Montana Section, with headquarters at Butte, and having such territory as may, later be determined on. This petition was granted by the Board at its meeting in Butte, Mont., Aug. 20, 1913. The committee named at the head of this paragraph was appointed to' arrange for permanent organization of this section.

Jan 9, 1913