Search Documents

By R. E. Hucko

Introduction The principal thrust of the US Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce ash and sulfur content of US coals to levels where the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The coal preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas - coal characterization, beneficiation, and ancillary unit operations.

Jan 1, 1985

By A. Kavetsky, W. J. Whiten

Data from ball mills with a wide range of diameters are analyzed using detailed mathematical/ numerical models. Analysis shows the relative power inefficiency of large ball mills is due to their inefficient breakage of coarse particles. The models developed can be used to scale-up mill behavior. The behavior of large mills at Bougainville and Pinto Valley is compared. It is concluded that the mills are equally inefficient at grinding coarse particles. Differences in coarseness of total mill feed are shown to account for the fact that Pinto Valley mills achieved design throughput whereas Bougainville mills did not.

Jan 1, 1985

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 12, 1979

By W. Arthur White

Underclay squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay-making it more plastic-or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards.

Oct 1, 1956

By P. Ramakrishnan, Ramjilal

Fine powders of lead zirconate titanate have been prepared by three different methods such as ball milling, conventional coprecipitation and spray drying. Different powders have also been prepared by changing the process variables in each method. These powders were analysed for particle size chemical composition and reactivity. DTA, TGA and x-ray analysis have been carried out to study the lead zirconate titanate formation with reference to calcination temperatures. The calcined powders were then consolidated by compaction and sintering. An attempt has bean made to explain the consolidation behaviour of these powders on the basis of powder characteristics.

Jan 1, 1980

What has been billed as the underground drilling technology of the 1980's got a dramatic head start when Boliden engineers at Stekenjokk decided to go with all hydraulic drilling for primary ore production and mine development. This application represents a major first in meeting the needs of high productivity, better energy utilization, and an improved drilling environment. At Stekenjokk, engineers chose three Atlas Copco Boomer H132 two-boom electro-hydraulic drill rigs with the COP 1038 rock drills. An additional single-boom Boomer H131 was also selected with the COP 1038 HD for roof bolting functions.

Jan 12, 1977

By Ali Altway, M. E. Tunison, T. W. Chapman

Simulations of various contactor configurations for simultaneous extraction or stripping of two metals reveal the dependence of conversion and selectivity on operating and design parameters A two-film mass transfer model is used to provide the rates in countercurrent column and stirred-tank cascade calculations Even in these mass-transfer-limited cases the stoichiometry of the extraction reactions introduces nonlinearities and interactions between the two metal transfer rates, but these can be represented In a suitable model One conclusion is that a countercurrent column should be considerably more efficient than a cascade of mixer-settlers of comparable size.

Jan 1, 1981

By M. Lastra, A. Cruz, J. Menacho

The technical feasibility of treating exotic copper ore with an acid cure using concentrated H2S04 is studied. Applications in a conventional percolation leaching circuit for unaltered ore and in a conventional agitation leaching circuit for altered ore are examined. The main effects of an acid cure are to inhibit silica dissolution and to increase the sedimentation rate of agitated pulps. An increase in the rate and degree of copper extraction is also observed. Based on these results and the minimal additional investment required, acid curing appears to provide an excellent approach for treating exotic copper ores.

Jan 1, 1980

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

By G. F. Moulton

Extraction of minerals from Searles Lake brines has taken place since 1873. Early operations for borax and raw trona found on the surface were expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1982

By Walter E. Heinrichs

Before covering the separate methods used in mining geophysics, it may be well to mention some current basic geophysical prospecting concepts. As in most fields, a better understanding and means of studying these fundamentals usually provides the more common improvements, rather than new principles being discovered. The relative detail and complexity of most mining geology often results in the use of geophysics in problems it cannot solve. On the other hand, suitable applications are often ignored or left unrecognized. To minimize this, it is important to consider geophysics as a phase, or additional tool, in geological or exploration engineering.

Aug 1, 1956

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By Robert S. Schecter, Paul M. Bommer

This paper presents the development of and results from a computer model of in situ uranium leaching. This model uses a streamline-concentration balance approach and is useful with a wide range of reservoirs. It can be used with any type of well system, in a reservoir with or without boundaries, and with any form of descriptive kinetics. The model also includes the effects of dispersion and consumption of oxidant by minerals other than uranium. The effects of areal sweep, variable uranium concentrations, variable permeability, and the presence of oxidant consumers on uranium production are shown and discussed.

Jan 1, 1979

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years. By ignoring all but the relevant characteristics of a process, a mathematical simulator may be constructed which, when fed operating data, should react as the process would. The output becomes numbers, instead of tons, however. Thus, a trial-and-error operation of such a simulator will permit management to study a major system change at little cost.

Jan 1, 1967

By R. E. Johnson, J. W. Donaldson, D. B. George

Accurately predicting the minor element content of an anode product is an important part of an evaluation of copper smelting processes. A general review of the minor element behavior in copper smelting is presented with the techniques to predict anode quality as a function of important process variables. Among variables considered are concentrate composition; recycle of dust, sludges and other intermediate byproducts from smelters and refineries; and other important smelting variables, including matte grade and the slag cleaning process. To evaluate the complex nature of minor element behavior relative to these variables, special techniques have been developed and are described.

Jan 1, 1976

Terminology Relating to Nonmetallic Elements in Metals. BY T D YENSEN AND C H HERTY, JR (Tech Pub 555, Metals Tech, June 6100 words ) The paper gives arguments for confining the term "gases in metals" to its proper sphere and recommends the name "nonmetallic elements in metals" as a general title of the subject dealing with: (1) nonmetallic elements introduced into metals unintentionally or for various specific purposes; (2) phenomena occurring in metals caused by non¬metallic elements It also recommends a classification of the subject in which "gases in metals" occupies a definite, logical place

Jan 1, 1935

By José Aloisio Paione, Eudes Prado Lopes

The geophysical exploration carried out by the Brazilian government through the Mineral Resources Development Co. (CPRM) to discover and develop Brazil's mineral resources is discussed. Particular mention is made of procedures specially adapted for contracting companies specialized in geophysics, CPRM's activities, statistical data from study programs, as well as the financial investments committed. More than 500 000 km of aerogeophysical surveys have been carried out by CPRM in the last four years, and it is expected that more than 600 000 km will be flown in 1974 and 1975, at an investment of approximately $30 million.

Jan 1, 1977

By C. D. Henry, M. L. W. Jackson

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of state and federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1984

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

By Roderick K. Davey

Introduction in any business, it is essential that we select those alternatives which are not only technically feasible, but will be the most profitable to the business m terms of corporate objectives Some of the studies and activities requiring support of financial analysis to select the alternatives which most closely satisfy the management objectives and technical considerations are as follows 1 ) Cutoff grade determination. 2) Ore reserve estimation. 3) Production forecasts (long- and short-term) for an operating mine, development of a new mine, or expansion of an existing mine. 4) Evaluation of haulage alternatives. 5) Evaluation of equipment.

Jan 1, 1979