Search Documents

By D. A. Summers, C. J. Haas, G. B. Clark, J. W. Brown

While significant advances have been made in excavation of rock, largely in improvements in drilling, blasting, loading, and haulage, conventional operations have been improved until little feasible increase in efficiency or rate of advance appears possible. Tunnel-boring machines have been developed which will excavate at rapid rates in soft to medium- hard rock. Hypervelocity impact is being intensively investigated as a possible means of cutting and breaking rock, as well as lasers, electric current, explosive drilling, high frequency vibration, etc. The current development and use of high-velocity small-diameter water jets, metallic jets, and projectiles of various materials involve ultra-high-pressure phenomena of fundamental interest. Rock disintegration by water jets has been investigated in the USSR for over a decade. Large-diameter jets of low velocity are used to mine coal, and high-velocity capillary jets will cut and break rocks under laboratory conditions. Velocity ranges for breaking and cutting are dependent upon rock and jet properties, and pulsed jets break some rocks more easily than continuous jets. Spectacular laboratory results have been reported for breakage of unconfined blocks of some types of rocks. Compressors, pressure multipliers, gas explosion chambers, and water cannons have been used to generate jets. Jet properties, such as continuity, unit pressure, total pressure, and stability have been measured. Results agree with theory, although the latter has been established only for relatively low-velocity flow. Diameter, speed of traversing, and frequency of pulsed jets affect rock response. Investigations in Britain have only recently begun consideration of harder rocks and higher velocities, although water jet cores have been found to be more continuous at lower velocities than previously believed. Lower limits of jet velocity for rock cutting were established for the rocks investigated.

Jan 1, 1970

An extra-tough rubber is the answer to many maintenance problems.

Jan 8, 1951

By AIME AIME

TO attempt to say anything adequate about Eugene McAuliffe as a human being, engineer, or executive in this brief space is ridiculous, for one could extol his virtues at length in all three catagories. Too, one might dwell on his good humor, and also his modesty, for lie did not wish even these few words to be said, "having no illusions regarding either ability or achievement, not even blessed with good looks." Mr. McAuliffe was born in England just seventy years ago. Twenty years later he started at the bottom with the Northern Pacific, gradually being promoted to locomotive fireman, engineer, and so

Jan 1, 1936

By H. A. Gardner, G. B. Heckel

The principal use of barium sulphate is as an inert paint pigment.

Jan 1, 1915

By Gordon Fletcher

Pacific Rim countries currently have plans to import about 100 Mt/a (110 million tpy) of steam coal by 1990. Due to its close proximity, Powder River Basin coals offer a long term economic and dependable source of supply to the Pacific Rim. In existing boilers, Powder River Basin coals can be blended with Australian, South African, or Canadian coals. For new units, Powder River Basin coals are very competitive on a total evaluated cost basis. The advantages of using Powder River Basin coal include: assurity of supply, consistent coal quality, stable labor force, and attractive mining economics. (NOTE: PAPER NOT RECEIVED IN TIME FOR PUBLICATION.)

Jan 1, 1982

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the first half of March: James C. H. Ferguson, San Francisco, Cal. Capt. A. F. Lucas, Washington, D.C. Henry Adams, Stamford, Conn. Dexter P. Cooper, New York, N. Y. H. A. Wheeler, St. Louis, Mo. L. D. Moore, Chatham, N. J. John M. Sherrerd, Easton, Pa. Hennen Jennings, Washington, D. C. R. T. White, formerly General Manager of the Braden Copper Co., Chile, is to take charge of a copper company in Caucasus, South Russia.

Jan 4, 1914

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position of laboratory assistant in metallurgy, pyrometry, and physical testing is vacant. Salary $80 to $100 to start. Knowledge of metallography desirable. Opening for a mine superintendent familiar with stoking methods on narrow gold quartz veins; also for a. superintendent of a 50-ton fine-grind-in, cyanide mill. College man under 40 preferred. Position in sales department is open for a mining engineer, with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions.

Jan 10, 1913

By Corale Brierley

The effect of hydrogen peroxide (H202) on growth and respiration of Thiobacillus thiooxidans and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uarnium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were totally inhibited after contact with 0.82 mM H202. Complete inhibition of oxygen uptake by T. ferrooxidans occurred at 8.75 mM H202, and growth was inhibited after 6 hr exposure to 2.06 mM H202. Higher concentration of H202 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface.

Jan 1, 1980

By Joseph R. Hatch

When compared to average shale composition, average coal is enriched in sulfur and selenium, has similar amounts of arsenic, beryllium, lead, antimony and molybdenum, and is depleted in at least 26 other elements. Within a coalfield, or region, some coals are enriched (10X average shale) in silver, arsenic, cadmium, cobalt, germanium, molybdenum, nickel, lead, selenium, uranium, and zinc. Important factors controlling element distributions in coal include geochemical conditions (primarily pH) in the peat swamp, composition and depositional environment of coal roof rocks, thermal maturity (rank), nature and intensity of any epigenetic mineralization, composition of ground waters that come in contact with the coal, and degree of weathering.

Jan 1, 1983

By Paul R. Smith

Preparation for flotation begins with dragline mining, pumping, washing, screening, and desliming. Slimes, nominally -150 mesh material, constitute large quantities of phosphate and water which are a disposal problem. Older techniques involve sizing at about 35 mesh for separate coarse and fine treatment. The plus 14 mesh fraction does not require concentration. Coarse treatment includes agglomerate spiralling, belt flotation, thickening, scrubbing with sulfuric acid, de-oiling for reagent removal, and cationic flotation of fine quartz. A recent trend is to screen at coarser than 35 mesh size and eliminate coarse particle treatment, sacrificing some grade of this product. Techniques for flotation concentration of the fine size fraction are discussed.

Jan 1, 1976

By Jerome S. Nelson, William S. Johnson

Seismic investigations at pre-construction sites commonly are limited to obtaining velocities and thicknesses of subsurface intervals which are useful in estimating construction costs, but are sometimes difficult to apply to project designing. This paper shows through a case history of the San Bernardino Tunnel Intake Tower, a part of the California State Water Project, that dynamic rock properties and dynamic resonant frequencies can be determined and velocity models constructed from in situ field studies and that these are theoretically correct after simplifying assumptions are made. These data can be used to confirm and extend information obtained by conventional methods such as drilling and laboratory static testing.

Jan 1, 1971

By J. Leja, N. Sheikh

The stability of lead ethyl xanthate precipitate in aqueous environment of different pH (4.5 to 10.5) and at temperatures 25°C-60°C was investigated. Dissolution leads to a wide variation of pH, xanthate, and lead ions concentration in solution and to a deposition of solid products of reactions. X-ray diffraction patterns of these solids enabled identification of Pb(OH)3, PbCO3, and PbS as constituents of the remaining undecomposed Pb(EtX)1, together with some unidentified compounds (which give rise to intensive peaks with d values of 2.82A and 1.71A, and numerous peaks of lesser intensity).

Jan 1, 1974

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Member, aged 25, recent graduate, with some experience in laboratory of steel plant, desires position as metallurgist or assistant in copper, aluminum, or steel works. No. 118. Member, aged 52, technical graduate, with 20 years' experience as engineer with coal-mining companies, desires position as engineer or superintendent of coal mine. No. 119. Member, aged 39, technical graduate, with extended experience in surveying, assaying, milling, and copper smelting, desires position along cyaniding, concentration, or copper-smelting lines. No. 120. Member, aged, 38, technical graduate, with several years' experience in research work, in mine operation and as professor of mining engineering, is desirous of engagement in planning concentration and metallurgy of odd and difficult ores. No. 121. Member, aged 32, graduate M. I. T. in mining and metallurgy, at present and for last five years superintendent of Western lead smeltery, will consider engagement with solid company, if opening promises advancement. Specialty, smelting of lead ores, high in lead and zinc content. Ten years' experience in the operation, design, and erection of a large lead plant. Now desirous of bettering position.. No. 122.

Jan 8, 1914

No. 264. A long established company operating steel and iron foundries, machine and forge shops, whose varied products are sold to the Government, railroads, mining and contracting industries, etc., has, openings in both manufacturing and selling departments for men with technical education and experience who are not subject to military call. State full particulars, kind of position preferred and salary expected. No. 265. Young man wanted, technical graduate preferred, to superintend construction f a small charcoal blast furnace. Man with blast-furnace experience preferred. For the right kind of man this is, not only a permanent job but an opportunity. In writing, give full particulars as to age, education, experience, salary wanted, etc. No. 26.6. An important copper mining and smelting company in Arizona needs two or three metallurgical chemists, at salaries. ranging front $150 to $175 per month. No. 267. A consulting mining engineer needs two superintendents for developing chrome deposits near Philadelphia; and another technical man for other engineering work in the same vicinity. No. 268. An iron-mining company, in New York State needs a mining engineer with knowledge of geology and acquaintance with construction work; A married man, with about 10 years' engineering experience preferred.

Jan 2, 1918

By G. K. Burgress, H. S. Rawdon, R. W. Waltenberg, J. J. Crowe

The main objects of this investigation were to determine, from neasurements taken at representative rail mills…

Jan 1, 1915

US 4,201,749-In the Bayer process production of alumina wherein aluminum hydroxide is precipitated from a sodium aluminate solution for use as seed, sodium oxalate and caustic components are removed from the precipitate by washing it first with a washing liquor which is saturated with sodium oxalate but has little content of caustic, and secondly with hot water. Substantially no sodium oxalate is recycled, yet loss of sodium aluminate is minimal. K. Yamada, T Harato, and H Kato, assigned to Sumitomo Aluminum Smelting Co Ltd May 6, 1980 8 pp. (423-127). Filed. 5-8-79 (37,145) Priority. Japan, 5-8-78 (53/54,803). Same¬British 2,020,642, dated Nov. 21, 1979.

Jan 1, 1982

By Harold R. Bradford

EXPANSION initiated during and after the war has placed industrial plants in new areas and increased reduction and manufacturing facilities in communities already established. With added expansion interest has grown in possible area contamination from waste products. Evolved flue waste contains many chemical contaminants that may or may not cause concern; however, atmospheric pollution has always been a problem to industrial communities. For some time effects attributed to small quantities of compounds of fluorine in various waste gases have been studied by industrial, medical, agricultural, and associated interests.1,2 Aside from an article by Churchill, Rowley, and Martin in 1948,3 little has been published on the subject of fluorine in coal except by foreign investigators.

Jan 1, 1957

University of Alabama-University, Alabama, Mining and Metallurgical Society, James W Stewart University of Alaska-College, Alaska, Mining Society of the University of Alaska, Jack R Hoskins University of Arizona-Tucson, Arizona, Miners Society, A E Gorum Birmingham-Southern College-Birmingham, Alabama, Pick and Hammer Club, Daniel D Arden University of British Columbia-Vancouver, British Columbia, G M Dawson Club, A Gunning University of California-Berkeley, California, Mineral Technology Association, Bernard York Carnegie Institute of Technology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann City College of New York-New York, New York, CCNY Student Chapter AIME, Daniel T O'Connell

Jan 1, 1955

Univ of Alabama-University, Alabama-Mining and Metallurgical Society William L Mason, Faculty Sponsor, E C Wright, Dept Head Univ of Alaska-College, Alaska-Mining Society of the Univ of Alaska Douglas W Huber, Faculty Sponsor, E H Beistline, Mining & Metallurgy Dept Head, Troy L Pewe, Geology Dept Head, James Crawford, Chapter Counselor Univ of Arizona-Tucson, Arizona-Miners Society Willard C. Lacy, Faculty Sponsor, J D Forrester, Mining & Metallurgy Dept Head, F. W Galbraith, Geology Dept Head Univ of California-Berkeley, California-Mineral Technology Association H E Hawkes, Faculty Sponsor, Joseph A Pask, Dept Head Carnegie Inst. of Technology-Pittsburgh, Pa -The Metals Club William R Bitler, Faculty Sponsor, Robert F Mehl, Dept Head

Jan 1, 1960