Search Documents

By Reynold Q. Shotts

INTRODUCTION THE small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive accumulation of coke in the form of "trees" or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow. most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of laboratories 1, 2, 3, 4, 5 are one method of approach to the problem of selecting stoker coals. As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simple measure of the tendency of a coal to form coke in a fuel bed. Although possessing all of the disadvantages of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects of swelling properties upon combustion. 7 Ostborg, Limbacher and Sherman, have shown that the test can predict, roughly, the tendency of coke to accumulate in the fuel bed of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1948

By C. E. MacQuigg

In this paper it is impossible to more than touch on many of the commercial alloys of iron, chromium, and carbon, therefore the discussion is confined to the properties of some of the less well-known alloys with upwards of 20-per cent. chromium. The discussion has been based largely on the strictly engineering aspects of the alloys. Chromium has well-defined effects when added to the iron-carbon system. These effects depend on the amount of chromium added and on the composition of the iron-carbon alloy to which the addition is made, i.e. whether low- or high-carbon steel, cast iron, etc. In the case of the low-carbon steels, the chromium addition, when not in excess of several per cent., appears to exert an influence on the properties by its influence on the critical range. In the higher chromium alloys, the physical properties are influenced chiefly by the formation of new complexes, such as iron-chromium solid solutions and, with higher carbon contents, iron-chromium carbides of great hardness. Examination of the published data1 on the critical range phenomena of chromium-bearing steels up to several per cent. chromium indicates an agreement on the following points:

Jan 1, 1923

By G. C. McCartney, S. J. Kidder

The Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies—i.e., the oxide ores of the Old Helen and the siderite of the New Helen—are a part of a tabular shaped area of iron formation that extends over a length of more than 100,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source. Introduction The Michipicoten mining district derives its name from the Indian word1 meaning "place of bold promontories" or "region of big places," and anyone who has visited this part of Canada will agree that the district is well named. In 1897, there was active prospecting for gold in the district and the Ontario Bureau of Mines2 opened a recording office at the Hudson's Bay post at Michipicoten River. In the summer of 1897, Ben Boyer, probably searching for gold, discovered an outcrop of brown iron ore at the east end of a small lake, less than 8 miles, in an air line, northeast of the nearest point on Michipicoten Harbour. In the following year, extensive surface exploration and diamond drilling disclosed a commercial body of nonbessemer brown ore, possibly 700 ft. long and 200 ft. wide, of about the following analysis:3 Fe (natural), 57.15 per cent; S, dried at 212°F.. 0.113; SiO2, dried at 212°F., 4.00; P, dried at 212°F., 0.125. The property (Figs. 1-3) was taken over by E. V. Clergue and ultimately was transferred to the Algoma Steel Corporation. The Algoma Central Railway shortly afterward built its line from Michipicoten Harbour to the mine, together with an ore dock at the Harbour. Thus, within three years of its discovery, the mine had adequate shipping facilities and a market for its ore. Production of Brown Ore and Pyrite The first shipment of brown ore was made in July 1930. By 1939, the mine was shipping at the rate of 170,000 long tons

Jan 1, 1949

By C. E. MacQuigg

In this paper it is impossible to more than touch on many of the commercial alloys of iron, chromium, and carbon, therefore the discussion is confined to the properties of some of the less well-known alloys with upwards of 20-per cent. chromium. The discussion has been based largely on the strictly engineering aspects of the alloys. Chromium has well-defined effects when added to the iron-carbon system. These effects depend on the amount of chromium added and on the composition of the iron-carbon alloy to which the addition is made, i.e. whether low- or high-carbon steel, cast iron, etc. In the case of the low-carbon steels, the chromium addition, when not in excess of several per cent., appears to exert an influence on the properties by its influence on the critical range. In the higher chromium alloys, the physical properties are influenced chiefly by the formation of new complexes, such as iron-chromium solid solutions and, with higher carbon contents, iron-chromium carbides of great hardness. Examination of the published data1 on the critical range phenomena of chromium-bearing steels up to several per cent. chromium indicates an agreement on the following points:

Jan 1, 1923

By John Henry Harden

This shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & WilkesBarre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51' 2" long, 17' 4" wide, 31' deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45' 4" long, 11' 16" wide, 31' deep, divided into six parts by buttons 8" x 12", each division, 7' x 11' 6". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10" ; backing, 3" thick ; clay puddle to exclude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the "standard diamond " car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet." Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pressure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams.

Discussion of the paper of Woolsey McA. Johnson, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1137 to 1145. F. L. GRAMMER, Leesburg, Va. (communication to the Secretary *):-Mr. Johnson's paper must interest by suggestion those connected with the " burning " of lime, the production of cement, and the smelting of iron. All iron men know how quickly the impalpable purple ore of wet origin reduces compared to finely ground red hematites of approximately identical composition obtained from Lake lump ores. Most housekeepers appreciate that the several forms of carbon-charcoal, coke, and anthracite, not to include graphite and diamond -have different temperatures of ignition. The temperature usually rises with the density and hardness. Some of the scientific bureaus of the government might appropriately conduct some tests along lines suggested by Mr. Johnson's article. We are unable to say whether the topic lies within the spheres of activity of the Bureau of Mines, the Bureau of Soils (Agricultural Department), the Geological Survey, or the Bureau of Standards. The calcining qualities of limestone is a topic too wide for individual effort and is of wide enough interest to merit government or State activity. It is of interest, as aforesaid, to burners of lime, cement manufacturers, and smelters. The chemical composition of a limestone does not tell all the story -if over 1-in. size lumps. The limestones of Annville and Myerstown, Pa., break at a tap; those on the Hudson above Poughkeepsie .act like "nigger heads." The manager of lime kilns near Lake Champlain told me his fuel consumption was high compared to that at other points. Yet the Hudson and Annville stones were both of greatest purity, being rivaled by only the marble at Rutland, Vt., or some stones near Martinsburg, W. Va. A local kiln operator says the conglomerate or pudding limestones of Loudoun county, Va., act very differently in the kiln from the more normal limestone deposits nearby. The tilted and twisted bedding in the anthracite region tells the story of hard coal origin. We might therefore expect that the limestones of greater geological age or depth or metamorphism

Jan 11, 1913

By W. A. Tiller, J. P. McHugh

HE majority of liquidus and solidus surfaces in phase diagrams have been determined by the conventional cooling- and heating-curve techniques.' These techniques have two main shortcomings: 1) the solidus may be in considerable error due to the difficulty involved in completely homogenizing the solid and 2) the determination of liquidus and solidus in more than a two-component system does not enable one to determine tie-lines connecting the specific equilibrium solid and liquid compositions. However, in a recent paper by one of the authors,' a method was suggested whereby the liquidus and solidus surfaces plus tie-lines in an n-component system may be determined. This method utilizes a controlled solidification technique and assumes that interface equilibrium exists during freezing. The present work was undertaken with a twofold purpose; first, to determine the liquidus and solidus lines in the pseudo-binary system Bi2Te3-Bi2Se3 by heating- and cooling-curve techniques and, second, to determine the partition coefficients of Te and Se in the BizTe3-,Sex system by controlled solidifica- tion techniques. The two sets of results can be compared to test the accuracy of the controlled solidification method. EXPERIMENTAL I—The starting materials for this study were 997999 pct Bi, Te, and Se, obtained from the American Smelting and Refining Co. The compounds BizTe, and Bi2Se3 were each prepared by melting together stoichiometric amounts of the elements, followed by twelve zone-refining passes. This produced homogeneous bars of the compounds for use in the phase-diagram studies. The apparatus used to obtain heating and cooling curves is illustrated schematically in Fig. 1. The alloy samples were located in a graphite crucible placed in a stainless steel canister. The canister was supported in a heavily lagged pit furnace by a device which oscillated the canister about its vertical axis at a frequency of about 3 cycles per sec during heating and cooling-curve runs. The graphite crucible was designed to minimize the thermal coupling of the sample to the furnace. A thin graphite sleeve separated the alloy sample from the stainless steel tube that housed the thermo-

Jan 1, 1960

By S. J. Kidder, G. C. McCartney

The Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies—i.e., the oxide ores of the Old Helen and the siderite of the New Helen—are a part of a tabular shaped area of iron formation that extends over a length of more than 100,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source. Introduction The Michipicoten mining district derives its name from the Indian word1 meaning "place of bold promontories" or "region of big places," and anyone who has visited this part of Canada will agree that the district is well named. In 1897, there was active prospecting for gold in the district and the Ontario Bureau of Mines2 opened a recording office at the Hudson's Bay post at Michipicoten River. In the summer of 1897, Ben Boyer, probably searching for gold, discovered an outcrop of brown iron ore at the east end of a small lake, less than 8 miles, in an air line, northeast of the nearest point on Michipicoten Harbour. In the following year, extensive surface exploration and diamond drilling disclosed a commercial body of nonbessemer brown ore, possibly 700 ft. long and 200 ft. wide, of about the following analysis:3 Fe (natural), 57.15 per cent; S, dried at 212°F.. 0.113; SiO2, dried at 212°F., 4.00; P, dried at 212°F., 0.125. The property (Figs. 1-3) was taken over by E. V. Clergue and ultimately was transferred to the Algoma Steel Corporation. The Algoma Central Railway shortly afterward built its line from Michipicoten Harbour to the mine, together with an ore dock at the Harbour. Thus, within three years of its discovery, the mine had adequate shipping facilities and a market for its ore. Production of Brown Ore and Pyrite The first shipment of brown ore was made in July 1930. By 1939, the mine was shipping at the rate of 170,000 long tons

Jan 1, 1949

By A. S. Nowick, C. Y. Li

It is deMonstrated that quenching from an elevated temperataupe accelerates the grain boundary relaxation in two solid solutions (aAg-Zn and a Cu-Al). This result is consistent with the proposal that, in solid solutions, grain boundary relaxation occurs by a mechanism of' self diffusion. Nevertheless, an alternative possibilitg, that quenching introduces vacancies into the boundary itself, must also be considered. THE phcnomenon of grain boundary relaxation has been well known for many years,1,2 yet the mechanism of this process is very poorly understood. One of the most interesting suggestions which relates to the mechanism of grain boundary relaxation was that of Ke,3 who claimed that the activation energy for grain boundary relaxation and for lattice self diffusion were essentially the same. The implication is therefore that the elementary step in the two processes is the same. This suggestion is particularly startling in view of the fact that activation energy for self diffusion along a grain boundary is very significantly lower than that for volume self-diffusion. Later evidence5-7 showed that there really are two grain boundary peaks, one which appears in high-purity metals, and the other (which develops at a higher temperature than the first) which appears in solid solutions beginning at solute concentrations in the range of 0.1 pct. Data for silver6 show that Kg's hypothesis is surely incorrect for the grain boundary peak in the high-purity metal, since it has an activation energy of only 22 kcal per mole, but that the hypothesis may still be correct for the grain boundary peak in various silver solid solutions, for which activation energies in the range 40 to 50 kcal per mole are observed. If the elementary step in the grain boundary relaxation process were the same as that for self-diffusion, it would be expected that the relaxation process could be hastened by quenching, 2.c. by introducing a non-equilibrium excess of lattice vacancies. Such a quenching effect has already been demonstrated in the case of another anelastic relaxation process, viz., the Zener relaxation effect. The Zener effect, which occurs in essentially all solid solutions, may be attributed to the reorientation of pairs of solute atoms in the presence of an applied shear stress,' and therefore must take place by means of a volume diffusion mechanism. The hastening of this process through quenching9 has been one way of demonstrating that atom movements in the lattice take place through a defect mechanism, presumably single vacancies. In order to see if the grain boundary relaxation is affected by quenching, it is particularly convenient to compare the grain boundary relaxation with the Zener effect, by choosing a specimen for which both relaxation effects appear. Specifically, a fine-grained sample of a solid solution shows in the curve of internal friction vs temperature, first a peak due to the Zener effect, then a second rise (and eventually a peak at substantially higher temperatures) due to the grain boundary relaxation. The same phenomena are also observable in static anelastic measurements, such as creep at very low stress levels. Thus, for the same fine-grained solid solution, the creepstrain, when plotted against log time, falls on a sigmodial curve with a sharp inflection point, due to the Zener effect, which is followed by a second rise and inflection resulting from the grain boundary relaxation. To look for a quenching effect, static measurements are preferable to the dynamic internal friction measurements, due to the fact that quenching effects tend to anneal out too rapidly at the temperatures at which the internal friction is measured.9 RESULTS AND DISCUSSION Creep experiments in torsion were carried out in an apparatus similar to that described by Ke1, whereby a wire is held under constant torque and its angular displacement is observed as a function of time. The alloy Ag-30 at. pct Znwas selected because of the large Zener relaxation that it displays. The two samples used were a "coarse grained" wire with a mean grain size about twice the diameter of the wire (diam = 0.032 in.), and a "fine-grained" wire which had several grains across the diameter. In Fig. 1 a comparison is made of the creep curves at 160°C of these two samples after they had been cooled slowly from 400°C. Curve A, which represents the coarsegrained sample, shows a unique relaxation process due to the Zener relaxation, with a relaxation time, T , in the vicinity of 100 sec. Curve B, which represents the behavior of the fine-grained sample, on the other hand, shows first the same relaxation process as that in A, followed by a turning up of the curve which corresponds to the onset of a second overlap-

Jan 1, 1962

By W. R. Bull, J. R. Roos

A method is described whereby the true financial value of each constituent of each concentrate can be calculated. Each value is then compared with what this value would be in a perfect separation. The difference in each case represents the loss incurred by each aspect of an inefficient separation. The relative magnitudes of these losses indicate those avenues of plant investigation and research that offer the highest potential reward. The metallurgical efficiency of a concentration operation is difficult to express because there are two criteria of performance, namely, grade and recovery. Neither of these alone gives any indication of the effectiveness of an operation and, if they are combined in some formula, it must be empirical and unreliable because of many external factors. Since milling is an operation performed as one step in the most profitable overall method of producing a metal or other end product, the main objective of mill operation should be to make a maximum contribution to this maximum profit. When concentrates are sold to custom smelters, the income from the operation, and the costs, may be calculated. When concentrates are further processed by another division of the same company, and there is no formal financial relationship between, say, the milling and smelting divisions of the company, the mill superintendent's job is less well defined. But even so, if the mill superintendent works as though he were selling his concentrates, and uses reasonable, if fictitious, conditions of sale, then he can get a good indication of the effectiveness of his operation by calculating his "Economic Recovery". ECONOMIC RECOVERY This is a method used as a basis of operation by several mills and has been described in the literature. Very briefly, the "standard" of operation is taken as that of a mill separating the ore into perfectly pure concentrates with 100% recovery of each mineral in its respective concentrate. For example, a 4%Pb, 4% Zn ore (galena and sphalerite), would provide a lead concentrate weighing 4.62% of the feed and assaying 86.6% Pb and a zinc concentrate weighing 5.97% of the feed and assaying 67.1 % zinc. These perfect concentrates are (hypothetically) shipped to the appropriate smelters, freight and treatment charges and payments calculated, and the net return obtained. This is the optimum financial return for the operation of the mill and is used as the standard. Now the return for the actual, real-life, mill operation is calculated in the same way, and the ratio of the two is termed the Economic Recovery. Many additions and modifications may be made in any particular case. For example, if the zinc mineral is marmatite, the optimum grade of the zinc concentrate may be set lower than 67.1%. If silver is present, it will be recovered 100% in the lead concentrate in the perfect operation. Similarly, cadmium will be recovered 100% with the sphalerite. Mr. Weiss' paper' mentions a case where, because of extremely fine intergrowth between the valuable mineral, chalcocite, and pyrite, the optimum grade of copper concentrate was taken as 45% Cu instead of the theoretical 80%. Each operation will present its own possibilities in this way.

Jan 1, 1970

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

HENRY M. HOWE, Bedford Hills, N. T. (communication to the Secretary?).-The authors valuable results as to the effects of the air-hardening temperature on high-speed steel may be summed up thus: Influence of Rising Air-Hardening Temperature on. High-Speed Steel Air-hardening microstructure Cutting Properties temperature S Austenite Grain Free Carbide Grains Boundaries Too low Small or Narrow Maximum Too soft undeveloped Intermediate, Well-developed Intermediate Little or even Best correct none Too high Coarse hide, even with Minimum . Weak, brittle, three-rayed crumbling stars Here the suggestion is that as the air-hardening temperature rises it causes two prominent effects, one helpful and the other harmful, the increase of the former exceeding that; of the latter up to a certain point, at which the steel is most useful, and then in turn being outrun by it. The first is the progressive dissolving of the free carbide in the austenite, increasing the stability of the red-hard state. The second is the progressive coarsening of the grains, and thickening of the intergranular cement, developing at last into spandril-like three-rayed stars of the 1,288° specimen. (2,350° F.) of Plate D, thus giving clear proof of incipient fusion, that is of crossing the solidus. This causes intergranular weakness. The individual grains may have great red-hardness, but they do not cohere. They approach the condition of a bag of emery grains.

Jan 6, 1917

By David A. Summers, Clark R. Barker, Marian Mazurkiewicz

In May 1975 the U.S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a longwall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting ahead. The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the coal cantilever over onto the conveyor [(Fig. 1)]. There were several potential advantages foreseen for the system; perhaps the most significant were the elimination of coal dust from the working area and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in haulage horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of Mines contract. The experiments showed that it was more advantageous to work at a pressure of 68.9 mPa (10,000 psi) with an estimated flow rate of 3.15 X 10 - 8 m3/s (50 gpm) than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1979

NORMAN B. PILLING (author's reply to discussion *).-The discussion by Mr, Bassett raised one or two points that deserve further discussion. The printed figure for the lead content of the copper used was 0.015 per cent. and not 0.15 per cent., upon which his comment was based. A copper having the latter figure would, of course, be quite unusual. Mr. Bassett takes exception to the writer's statement regarding the distribution of cuprous oxide in wrought copper and states that "the FIG. 1.--ROLLED AND ANNEALED SHEET. ETCHED WITH AMMONIA AND HYDROGEN PEROXIDE. X 75. eutectic of copper with cuprous oxide is usually found between the crystals of pure copper, whether in the cast or the wrought form." While it is very well known that during the solidification of cast copper the cuprous oxide is segregated completely as an envelope of cuprous oxide-copper eutectic around the crystals of copper free from oxide, it is the writer's opinion that, as a result of repeated rolling, this eutectic structure is quite destroyed and the small particles of cuprous oxide become widely scattered, and in the recrystallization following, during annealing, the rearrangement of the grain boundaries takes place with much indifference to the actual distribution of these particles. In the accompanying micrograph, taken from a rolled and annealed sheet, the random distribution of the small cuprous-oxide particles with reference to the location of the grain boundaries may be seen.

Jan 3, 1919

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By J. R. Low, M. B. Reynolds, L. O. Sullivan

The effect of neutron bombardment upon the stability of type 347 austenitic stainless steel has been investigated by a magnetic technique. The relation of the ferrite content of a stainless steel to its magnetic properties is given, and an apparatus suitable for the measurement of the ferromagnetic saturation induction of small specimens is described. Results of measurements on irradiated specimens are tabulated. Exposure to a neutron flux was found to cause a slight increase in the ferrite content of type 347 stainless steel, the change increasing with increasing length of exposure and with increasing initial ferrite content. The similarity of the effect of irradiation to the effect of annealing is pointed out. Possible effect of irradiation upon density of austenitic stainless steel is discussed. COMMERCIAL austenitic stainless steels are alloys of iron, chromium, and nickel, plus small quantities of other elements. Although these alloys are normally used in the austenitic condition, this state is thermodynamically metastable at ordinary temperatures and transformation to a more stable state takes place under favorable conditions. In the austenitic state, these stainless steels have the face-centered-cubic crystal structure characteristic of y iron, but the stable state at room temperature is a mixture of austenite and body-centered-cubic ferrite. The transformation from the pure austenitic condition may be brought about by cold working the alloy at a temperature below that at which the aus- tenite becomes thermodynamically unstable (about 400°C), the completeness of transformation increasing with increasing severity of cold work and decreasing temperature. The behavior of the austenitic stainless steels under ordinary conditions of use is rather well known. However, use of these alloys in a nuclear reactor introduces a new variable: the effect of neutron bombardment upon the transformation from the austenitic to the ferritic state. It was with this in mind that a study of the radiation stability of austenitic type 347 stainless steel was undertaken. Magnetic Technique for Ferrite Determination Commercial austenitic stainless steels such as type 347 undergo little transformation under normal conditions of fabrication and use. In view of this fact, it seemed likely that neutron irradiation would change the ferrite content of the alloy but little. The method chosen for measurement of the effect of neutron irradiation was thus limited to one which would be quite sensitive to small changes in the ferrite content of the alloy. Of the properties of the stainless steel which can be measured, the magnetic characteristics are most sensitive to the quantity of ferrite present.

Jan 1, 1956

By D. L. Katz

A PHASE diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The tempera-tures and pressures of phase measurements were in the range of 85° to 212° F. and 1300 to 2600 lb, per sq. in., respectively, with the critical conditions at 169.5° F. and 2615 lb. per sq. in. abs, Color phenomena were observed in the region of the boundary curve from 102° to 192° F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydro-carbons. 2,3,4,6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilib-rium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagrams but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha' within the two-phase area but not in, the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus.

Jan 1, 1939

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.' ' Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.'" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By Arthur C. Spencer

(Glen Summit Meeting, June, 1911.) THREE great deposits of iron-ore, in Camaguey and Oriente Provinces, Cuba, are well known to me through careful field-examinations executed in the years 1901 and 1907. In 1901 I visited the Cubitas iron-ore district, which lies about 12 miles distant from the city of Camaguey in a northerly direction, and the Mayari district, which includes the Sierra Nipe, lying opposite Nipe bay on the north side of Oriente Province. In 1907 I again visited the Cubitas district, and also made a sojourn of several days in the Moa district, where the extensive deposits of iron-ore were observed and studied. The observations of 1901 were made under the auspices of the then Military Governor of Cuba; Gen. Leonard Wood, and my conclusions concerning the value of these deposits were incorporated in a report.1 The examination of certain denouncements of iron-ore in the Moa district in 1907 was made in behalf of iron-masters operating in the United States, to whom I reported the existence of large amounts of easily-workable limonitic iron-ore, properly designated " brown iron-ore " in the terminology now current among iron-ore producers in the United States. In 1908 I published a paper entitled Three Deposits of Iron Ore in Cuba, outlining the occurrence and origin of the surficial ores existing in the Cubitas, Mayari, and Moa districts.2 . 1 A Geological Reconnoissance of Cuba, by C. Willard Hayes, T. Wayland Vaughan and Arthur C. Spencer, printed as a part of the report of the Military Governor of Cuba for the year 1901, vol. i. 2 Bulletin No. 390, U. S. Geological Survey, pp. 318 to 329 (1908).

Mar 1, 1911

By R. B. Gilmore

It has been the custom of the Railroad Commission of Texas to hold hearings each month with respect to existence and imminence of waste of oil and gas in Texas and its prevention, and to issue orders restricting the production of oil to the reasonable market demands and allocating production to the various fields in Texas. The practice of designating the actual days during the month on which wells are to be shut down was discontinued in the order for November 1942, and orders issued thereafter contain only the number of shut-in and producing days for the month. Orders issued by the Railroad Commission are divided into two main subdivisions, the first a general shutdown order of all oil wells in the various fields in Texas, and second, the exception of certain fields to this general order. Table I shows the producing days for all of the fields in Texas for 1944 under the first of these classifications : The fields that have producing schedules varying from the general order may be divided roughly into three subdivisions, as follows: Table 2 shows the producing days for certain fields that were prorated as a group throughout 1944. Other fields which were occasionally included with this group were also prorated under the general order and by special orders. The producing days for these irregular fields are shown in Table 4. In Table 3 are listed fields that were exempted from any shutdown days during December 1944, the majority retaining this exception throughout 1944. Certain fields included in the general order were added to this group on the first day of the month shown.

Jan 1, 1945