Search Documents

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928

By Alan R. Grant

The Cascade Range of Washington can be considered metallogenetically to be primarily a copper province. Structural and chemical data compiled from examination of numerous copper occurrences in the Cascades indicate a marked parallel of physical conditions for sulfide deposition. In probable order of significance, the environmental criteria are as follows: 1) adjacent or subjacent, postregional metamorphism high-level intrusive activity, most commonly in the time range from 15 million years to 30 million years; 2) transverse northeast trending structural belts which obliquely cut the northwest regional trend of the range; 3) potassium-silica wall rock alteration; most important of the alteration suite of silicates are orthoclase secondary biotite and quartz; 4) the intersection of northwest trending and northeast trending structures. The varying geologic environments in the Washington Cascades present a complex setting for the sulfide deposits. The North Cascades are comprised of predominantly pre-Tertiary metamorphic rocks invaded by Tertiary calcalkaline intrustive rocks. The Central Cascades, lying south of the North Cascades, exhibit a younger, higher level geologic environment comprised of predominantly early to middle Tertiary volcanic rocks and subordinate sedimentary rocks which are intruded by Tertiary calc-alkaline igneous rocks. Although the Tertiary Cascade intrusions are dominantly quartz dioritic, copper mineralization is commonly found in rocks of quartz monzonite to granite composition. These acid rocks appear to be the product of late stage magmatic K alteration of the original quartz diorites. Sulfide concentrations are considered to be in part dependent on the degree of K-silicate activity and the intensity of transverse structural deformation.

Jan 1, 1973

On the following pages are abstracts of papers published by the Institute during the year 1931 as Technical Publications, Preprints, and in bound volumes. For abstracts of papers that appear in bound volumes in 1931 but that were published as Technical Publications in 1930, see the Transactions, 1930. Papers that appear in the volume in which this list is printed are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 616. The abstracts are grouped as follows: Page Page Metal Mining....................... 578 ing and Metallography of Non-Milling and Concentration........... 578 ferrous Alloys)................586 IronandSteel...................... 580 Coal Division.. ................ 592 Petroleum and Gas.............. 598 Mctallurgy......................... 585 .............. 613 Institute of Metals Division (Found- Geophysical Prospecting......... 613 Metal Mining Use of Models for the Study of Mining Problems. By Philip B. Bucky. (Tech. Pub. No. 425, 12,000 words.)—This paper describes a research project undertaken to provide a means of studying the behavior of weighty structures such as mines, dams, foundations, etc., with models of the same material in the laboratory. The paper shows that in general it can be done. The underlying theory is explained, the apparatus which was developed and built to do this is described, and the results of laboratory experiments with sandstone mine structures are given. There is discussion of the accuracy of results with the present equipment, the model size necessary, and of the size and type of equipment necessary for the obtaining of results of practical value in the field. Milling and Concentration Ball Mill Studies, I. By A. W. Fahrenwald and Harold E. Lee. (Tech. Pub. No. 375. 25,000 words.)—This paper presents the results of an extensive experimental study of some of the numerous elements entering into ball mill grinding. All apparatus used was equipped with ball bearings. Every experiment was accompanied by a power measurement accurate to 0.005 hp. Quartz was used. Each element studied, such as ball load, was varied systematically. Power curves were obtained for the mill for three general sets of conditions; namely, (1) balls only (2) balls and quartz and (3) balls, quartz and water. For each general condition, power curves were obtained for various mill speeds, ball loads and ball sizes. For conditions 2 and 3, feed sizc and weight and pulp dilution also were studied as variables. The mill output, in grams of finished product per unit of time, was obtained for each test. In a general way, output (mill capacity) paralleled the power data and this attached

Jan 1, 1931

By W. T. Thom

In previous classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20 and 100 C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown' that such coals contain unstable groupings which decompose between 20 C. and temperatures somewhat above 100" C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100" C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100" C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 1, 1925

By A. M. Rahm

PROBABLY the majority of red brass sand castings are judged merely on the basis of outside appearance and the quality of machined surfaces. Many castings, however, must individually withstand a hydraulic or air-pressure test before being accepted as parts of more complicated machin-ery. Finally, there remains a comparatively small group of castings intended for uses of considerable responsibility where only the highest possible characteristics of the metal are acceptable, and for these specially cast test bars are required. The shape of the cast piece from which the test bar must be detached varies greatly from one country to another. The test bar as specified in the American Society for Testing Materials Specification B62-36 is widely used by the American foundry industry. The actual test piece is at the bottom of the cast block and has a riser about six times its mass. It is obvious that this test bar has an advantage over the actual casting. The latter rarely possesses a riser of as much as 30 per cent of its own weight and that riser cannot generally be located in so convenient a manner. Therefore, the characteristics of the test bar cannot possibly correspond to those of the casting itself. It must be taken into consideration that red brass if melted and cast in the best possible manner may show a tensile strength of 40,000 lb. per sq. in. with 35 per cent elongation in 2 in. Such a test bar would indicate that the metal was nearly perfect from the viewpoint of its gas and inclusion content. Barring some accidental defect, a casting cor-responding to such a test bar could be accepted as being quite sound. However, actual specifications do not demand such high characteristics; indeed, few specifications require over 30,000 lb. per sq. in. and 20 per cent elongation, while one Federal specification demands merely 27,000 lb. per sq. in. strength and 15 per cent elongation. It is obvious that

Jan 1, 1939

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By R. A. Ritter, J. P. Batycky

A numerical technique has been developed to permit estimating the pressure gradient associated with laminar flow of thixotropic liquids through long Pipelines. For this purpose the pipeline is divided into a number of radial and longitudinal increments within which rheological properties of the fluid may be considered as constant at any time. Then, provided only that the fluid flow curve is defined at every duration of shear, it is possible to predict the instantaneous pressure gradient at any cross-section along the pipeline for each desired flow rate and pipe size. The technique consists of an iterative integration of shear rate to establish the appropriate value of the wall shear stress at each location. Consistency of fluid in the increment is determined by the flow history of that increment, while the radial flow associated with variations in velocity profile is accounted for by adjusting the width and radial position of the increment. A number of pressure profiles, computed at each of several flow rates, provide a convenient basis for pipeline design and pump selection. INTRODUCTION In recent years considerable attention has been given to predicting pressure drop associated with the isothermal laminar flow of time-independent non-Newtonian fluids in pipes and annuli. 6,11,12 The approach generally has been to develop analytical relationships between flow rate and pressure drop based on simple constitutive models which hopefully provide an approximate description of the rheological properties of the fluid. Analytical solutions are highly desirable since the influence of all pertinent parameters can be readily determined. Unfortunately, however, this approach is restricted to simple flow geometries and- frequently leads to erroneous results due to inadequacies in the model. In certain cases a solution may be obtained through applying appropriate numerical techniques.l,14 For example, a digital computer program is available for predicting the velocity profile and pressure drop encountered by any Newtonian or time-independent non-Newtonian fluid flowing under laminar conditions in a cylindrical pipe or annulus.l In this paper the consistency behavior of the fluid need only be described in terms of basic rheological data. Analyzing flow systems involving fluids with time-dependent rheological characteristics is considerably more complicated since substantial changes in consistency may occur because of sustained shear action. This sensitivity to shear frequently persists for several hours. Consequently, variations in pressure drop and/or flow rate resulting from the aging process and addition of unsheared or partially sheared fluid to the system must be considered for purposes of pipeline design. This paper outlines a numerical method for predicting the transient and steady-state laminar flow behavior of a thixotropic liquid in a pipeline of arbitrary length (i.e., at a specified constant flow rate, the instantaneous pressure gradient may be determined at any time after start up and at any location along the pipeline). Several such pressure gradient profiles, computed at several flow rates, may be combined to produce a complete portrait of the system response. This flow portrait provides a reasonable basis for pipeline design and for selecting a suitable pump characteristic. TIME-DEPENDENT RHEOLOGICAL BEHAVIOR The most familiar time-dependent rheological properties are those exhibited by thixotropic liquids. Many of these materials, particularly thixotropic crude oils, generally display an apparent yield stress in that a finite pressure gradient is required to initiate flow. Then, under the influence of sustained shear at a constant shear rate, the consistency systematically decreases to some final limiting value. The shear stress obtained at

By M. Semchyshen, A. P. Coldren, W. G. Scholz

A survey of the Fe-Mo-B system was made to determine the extent to which boron might affect the microstructure and strength properties of iron-rich Fe-Mo alloys. Seventeen vacuum-induc tion melted ingots were prepared with approximate mo-lybednum contents 01 2, 4, 9, and 19 wt pct and approximate boron contents of 5, 14,50, and 630 ppm by weight. Phases extracted from annealed specimens and identified by X-ray diffraction analysis included E Fe3MO2, Mo2FeB2, and an oxide hazling a diffraction pattern practically identical to that of MnFez04. Three types of alloy strengthening were observed: a) Fe-2 pct Mo-B alloys were hardenable by a bainitic-type transformtion of austenite to ferrile; b) Fe-4 pct Mo-B alloys were hardened by the solid-solution mechanism; and C) Fe-9 pct Mo-B and Fe-19 pct Mo-B alloys were hardened by precipitation of the E Fe3Moz phase. Boron was observed to have a very strong hardening effect in the Fe-2 pct Mo alloys and a mild strengthening effect on the 1200°F properties of the Fe-4 pct Mo alloys. In the Fe-9 pct Mo alloys there was no consistent effect of boron on strength at either room temperature or 1200° F. The Fe-19 pct Mo alloys were so brittle that meaningful tensile or creep-rupture data could not he obtained. No dispersion hardening from borides was recognized in any of the alloys. THE high-temperature properties of iron-rich Fe-Mo alloys were studied by Reiter and Hibbard.' They found that the strength of the alloys increased markedly as the molybdenum content was raised from 0 to 15.9 pct by weight. The authors explained the various degrees of strengthening in terms of a) solid-solution strengthening, b) strengthening from a martensitic-type transformation, and C) precipitation strengthening. The objective of the present investigation was to conduct a survey of the iron-rich portion of the Fe-Mo-B system to determine whether the beneficial effects of molybdenum on the strength of iron can be enhanced by the presence of boron. It was thought that perhaps fine dispersions of molybdenum- rich borides would be found which could improve the high-temperature strength of ferritic alloys beyond the strengths attainable by molybdenum additions alone. Also, it was considered worthwhile to study the effects of boron in alloys which are essentially free of carbon. Most, if not all, of our present knowledge about boron in high-temperature alloys pertains to alloys containing carbon and carbides. EXPERIMENTAL PROCEDURES Alloy Preparation. Seventeen 8-lb ingots were prepared from electrolytic Plastiron, unalloyed molybdenum chips, and boron powder by a vacuum-induction melting procedure employing hydrogen as the main deoxidizer. The alloys were melted in alumina crucibles using 35-lb melts, with each melt being split four ways to achieve varying boron contents within four Fe-Mo base compositions. The results of chemical analyses conducted on chips machined from the chilled ends of the ingots are presented in Table I. The boron analyses were performed by a spectrographic method utilizing primary standards prepared from boric acid. They indicated that in ingots to which no boron was

Jan 1, 1964

By Augustus Locke

In 1900, when. the public first heard of "secondary enrichment," the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners' astonishment, they carried chal-cocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales' advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this argument. Especially pertinent was the proof that (1) the deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accomplished more easily than that of pyrite, enargite, or chalcopyrite. The microscopic evidence has been accumulating for ten years and it demands

Jan 1, 1924

By Milton E. Wadsworth

The reduction of a metal in an aqueous solution may be defined in terms of its source of electrons. In electrolytic reduction electrons flow as a result of applied voltages. In other systems electron sources are reducing gases or metals of lower electron affinity. In the latter two cases it is increasingly evident that reduction is electro-chemical in nature in that electrons flow through one or more conducting phases even though the discharge reactions may not be rate controlling. Electrode processes impmtant in reduction and metal deposition are reviewed and extended to contact reduction by precipitation (cementation) on mme electropositive metals. Contact reduc- tion Processes are ancient in origin and represent techniques which have had successful application for hundreds of years. In spite of this, little has been understood in terms of the dynamic properties of such systems or of important side reactions. In recent years an increasing amount of laboratory work has been carried out on contact reduction and an attempt is made here to summarize the important findings. Undoubtedly the interest aroused recently may be attributed to improved reactor design which has demonstrated on a commercial basis accelerated metal recovery by taking advantage of important kinetic and chemical parameters. of gold cyanide (Au(CN)-), respectively. The most common method for the reduction of ions in solution is by electrolysis. The impure metal is made the anode and the ions are reduced at the cathode. Leach liquors containing reducible ions may similarly be reduced electrolytically using an inert anode. The latter process is referred to as electrowinning. In recent years hydrogen has been used successfully as a gaseous re-Metallurgical Society of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). He was also a member of the Executive Board of the Metallurgical Society (AIME). In 1957 Dr. WADSWORTH was given the AlME Best Paper Award as coauthor of a paper on the roasting of sphalerite. On July 1, 1968 Dr. WADS-WORTH started an 24 month assignment in the Philippine Islands to assist in the development of graduate metallurgical engineering at the University of the Philippines. In addition to graduate teaching and curriculum development he will establish research programs to develop extraction processes for metals production in the islands. The project is supported by the Ford Foundation through Educational Projects, Incorporated.

Jan 1, 1970

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith' and of A. G. H. Andersen .2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford," using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,1,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates h in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

ANYONE who wishes to make the patterns for statues in order to cast them later in bronze, even though he himself is the artificer who made them, must take many things into consideration: first, whether they are large or small, and whether they are wholly round or only in part; then of what material they are made, for the way that can be followed if they are of wax cannot be used if they are of clay, wood, marble, or even of plaster; likewise he must consider whether or not it has irons inside to support it. There is also a great difference in facility if the support is placed more in. one way than in another. Great consideration should be given to whether it is to be made hollow or solid. If you have not been the workman yourself, you must at least have been an active helper in this and in every other part in order to be able to observe everything without a fault. For if they are large it is necessary to make their moulds in pieces, with marks and measurements so that you can replace them-at will exactly in the same order and in the same places after they have been taken out. But if you are the artificer [as well as sculptor] the process is made easier. Taking the ordinary way and, over an iron, make out of well beaten moulding clay, compounded with cloth clippings a core exactly as the statue is to be or however large you wish the hollow to be. Dry and bake it. On top of this work the wax, thickening it all over as much as you wish the bronze to be and finish it completely, remembering to arrange that the base may come out solid with bronze so as to support the whole work. Then take some rods of hammered bronze one dito thick and one palmo long. Pass these throughs the thickness of the wax and fasten them in several places in the core of clay that you made. [81] Do it so that they, project out of the wax a good three or four dita. These are, put in so that when the wax is removed the core is held in the middle of the mould that forms the outer part, and this outer part is held by the inner part, namely the core, so that the mould may not move in any part from its place even when it is handled. This done, take some of that clay made with well-prepared cloth clippings as I taught you, and mix with it if you wish some wash ashes or

Jan 1, 1942

By W. Rostoker, A. S. Yamamoto, K. Anderko

ALTHOUGH the corrosion resistance of magnesium and its alloys is closely related to iron content, there has been no direct measurement of the solid solubility of iron in magnesium. Bulian and Fahrenhors;1 and Mitchel]2 agree that pure iron or a limited terminal solid solution crystallizes from the Mg-rich liquid. For this reason a magnetic-moment method was selected to estimate that portion of the total iron content which is not in solid solution. Since iron in solid solution in magnesium cannot contribute to ferromagnetism, the difference between chemical and magnetic-iron analyses should yield the solid solubility. By experimentation it was found that the melting of pure sublimed magnesium (99.995 wt pet purity) in Armco-iron crucibles at about 800°C is a convenient way to introduce small amounts of iron. Melts retained 5, 10 and 20 min at 800°C analyzed 0.003,, 0.005,, and 0.018 & 0.001 weight pet Fe, respectively, after being stirred, heated to 850°C, and cast into graphite molds. The as-cast alloys were pickled in acid (dilute HC1 + HNO3), annealed at 600°C for 3 days, scalped on a lathe to remove the pitted surface, pickled again, extruded at about 100°C to 3-mm wire, reannealed 41/2 days at 500°C, and water-quenched. The specimens were again scalped, pickled, and used both for chemical and for magnetic analysis. Most of the precautions described were intended to prevent iron pickup by contact with tools or superficial iron enrichment by volatilization of magnesium during heat-treatment. It is believed that the specimens ultimately used for test were homogeneous and characteristic of phase equilibria at 500°C. Magnetic Analyses A susceptibility apparatus of the Curie type was used for magnetic analyses. Field strengths of up to 10,400 oersteds could be generated. By this method, an analytical balance measures the force of attraction which a calibrated magnetic field exerts on a suspended specimen. The force equation is as follows f/m = M dh/dy where f/m = force per unit mass of sample M = magnetic moment per unit mass dH/dy = magnetic field gradient The dH/dy characteristic of the instrument is determined by the use of a standard palladium sample, and the calibration is made independently for all values of H. Since a large finite field is required to saturate an assembly of ferromagnets, it is necessary to measure the apparent magnetic moment for increasing steps of H until a saturation value is obtained. The percentage of iron in the sample as free ferromagnetic iron may then be computed simply C= 100 (M1/M1) where C = percent content of undissolved iron in sample M1 = saturation magnetic moment of sample per unit mass M1 = saturation magnetic moment of iron per unit mass taken as 217 emu-cm per gm There is no serious difficulty in applying this method except for the unusual magnetic behavior of very fine particles of ferromagnetic substances. It has been found and is the basis for a widely accepted theory that with sufficient subdivision, the magnetic fields required to saturate and the coercive force after saturation rise to exceedingly high values. Recent work on precipitates of Fe and Co from copper solid solutions8 showed that about 5000 oersteds were necessary to approach saturation. The magnetic moments as a function of field strength measured in the present investigation are listed in Table I. Only the 0.018 wt pet Fe alloy yielded a magnetization curve with a fairly well-defined saturation plateau at 3.76x10 -2 emu-cm/ gm. This corresponds to 0.017 & 0.001 wt pet Fe in the alloy. This indicates that the solid solubility must be of the order of 0.001 wt pet Fe. The magnetic-moment data of the other two alloys are badly scattered, indicating that the amount of ferromagnetic iron in these samples is so low that the magnetic forces acting on them cannot be measured accurately by the analytical balance used. Nevertheless, the fact that even the 0.003, wt pet Fe alloy shows ferromagnetism indicates that the solid solubility must be below that value. Acknowledgment This work was sponsored by the Pitman-Dunn Laboratory of Frankford Arsenal, Philadelphia, Pa. The support and permission to publish are gratefully acknowledged. References W. Bulian and E. Fahrenhorst: Zeic. Metallkunde, 1942, vol. 34, pp. 116-170. 2 D. W. Mitchell: AIME Transactions, 1948, vol. 175, pp. 570-578. 3 G. Bate, D. Schofield, and W. Sucksmith: Philosophical Magnsine, 1955, vol. 46, pp. 621-631.

Jan 1, 1959

By G. N. Panagiotou

SIMPTOL, a computer simulation program written in FORTRAN IV for use with Cyber 171/8 System at the National Technical University of Athens, describes the mining operations in an opencast lignite mine operating Bucket Wheel Excavators, Conveyors and Stackers. The central objective of the program is to aid management in the selection of a BWE-Conveyor-Stacker System for a given lignite deposit and equipment layout. Much information can be gained from the program with proper manipulation of the input data, which refer to mining profile, soil characteristics, equipment specifications and availabilities and time study data. The other objective of the program is to aid production scheduling in terms of forecasting production rates of the system. The program has been applied to Kardia lignite mine to evaluate its usefulness to represent the actual situation of the system being simulated.

Jan 1, 1983

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By W. E. Keck, Paul Jasberg

TheRe is a considerable tonnage of iron ore in the Menominee Range of Michigan that is unsalable only because it has too large a content of sulphur. Beneficiation of such ore is economically desirable, as a relatively large quantity of finished concentrate would be obtained (deleterious sulphur mineral content being generally less than 5 per cent) and because large blocks of such ore have been developed incidentally during search for low-sulphur ore. Research on the flotation beneficiation of these high-sulphur ores consisted of: (1) a study of the flotative properties of the principal mincrals in a nearly pure state, (2) flotation of synthetic mixtures of these pure minerals and (3) application of this experimental information to samples of the ores. Gypsum in iron ores is extremely deleterious; but when sufficiently free from impurities it is a valuable commodity. In 1934, the United States produced 1,500,000 tons of calcined and uncalcined gypsum valued at $13,700,0001. Of this quantity and value, Michigan produced approximately 19 per cent1. Thus this investigation may also prove to be of interest in connection with the gypsum industry if minerals separation, such as flotation, becomes necessary in the future processing of gypsum. Data on the flotative properties of gypsum would also be of interest to the science of flotation because such information has been extremely limited. The technical literature reveals one reference to the flotation of gypsum, in which was discussed the use of the mineral, with several others, to determine the relation between the floatability of minerals and the pH of the flotation solution2. This investigation necessarily was not comprehensive in regard to gypsum, but it did show that the mineral could be floated with oleic acid under varying pH conditions.

Jan 1, 1938

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By W. E. Keck, Paul Jasberg

TheRe is a considerable tonnage of iron ore in the Menominee Range of Michigan that is unsalable only because it has too large a content of sulphur. Beneficiation of such ore is economically desirable, as a relatively large quantity of finished concentrate would be obtained (deleterious sulphur mineral content being generally less than 5 per cent) and because large blocks of such ore have been developed incidentally during search for low-sulphur ore. Research on the flotation beneficiation of these high-sulphur ores consisted of: (1) a study of the flotative properties of the principal mincrals in a nearly pure state, (2) flotation of synthetic mixtures of these pure minerals and (3) application of this experimental information to samples of the ores. Gypsum in iron ores is extremely deleterious; but when sufficiently free from impurities it is a valuable commodity. In 1934, the United States produced 1,500,000 tons of calcined and uncalcined gypsum valued at $13,700,0001. Of this quantity and value, Michigan produced approximately 19 per cent1. Thus this investigation may also prove to be of interest in connection with the gypsum industry if minerals separation, such as flotation, becomes necessary in the future processing of gypsum. Data on the flotative properties of gypsum would also be of interest to the science of flotation because such information has been extremely limited. The technical literature reveals one reference to the flotation of gypsum, in which was discussed the use of the mineral, with several others, to determine the relation between the floatability of minerals and the pH of the flotation solution2. This investigation necessarily was not comprehensive in regard to gypsum, but it did show that the mineral could be floated with oleic acid under varying pH conditions.

Jan 1, 1938

By Raymond Wilson

Grinding costs are an important item in cement manufacture, and the cost of power is one of the large items in grinding costs. Even where power is of secondary importance, cost items dependent on mill capacity are influenced by the efficiency with which the mill uses power. Tube mills typify the grinding mills most generally used in cement plants, though other types are in use. Tube mills have been widely criticized as being extremely inefficient, and this feeling regarding them has led to many attempts to design more efficient grinding equipment. Other types may be an improvement over tube mills, but the improvement has certainly not been revolutionatry, at least as applied to clinker grinding. The very fact that there is doubt regarding the relative efficacy of various types of mills is an indication that an adequate basis for an analysis of performance is lacking. The development of methods of analyzing mill performance has been hampered by the lack of a suitable method for measuring the work actually done in pulverizing. There has been no acceptable standard to which mill performance might be compared. As a consequence, it was not known whether the margin of possible improvement in pulverizing operations was large or small. Even direct comparison of different types of mills was seldom possible because most plants had only one type of mill for each type of service. Comparisons between plants were difficult because of differences in the grinding characteristics of various clinkers. Some recent developments complete a chain of circumstances that place the cement industry in a particularly fortunate position for the study of its clinker-pulverizing operations. Modern investigators of grinding phenomena have generally agreed that the best measure of mill performance is the production of new surface. For most materials this measure of performance is largely theoretical and has a rather remote connection with the practical aims of the grinding operation. In clinker grinding, on the other hand, surface area is intimately connected with the properties conferred on the cement by grinding. Morcover, the determination of surface area is rapidly coming into routine use as a tost

Jan 1, 1938