Search Documents

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution. Anaconda had done considerable work on the production of sponge iron in 1914 for use as a precipitant of copper from leach solutions. Some success and considerable experilence were attained at the time. indicating that, sponge iron might be successfully made by a modification of the process used in 1914, a batch process in which an iron calcine was reduced by means of soft coke, resulting from noncoking coal, in a Bruckner-type revolving horizontal cylindrical furnace widely used 50 years ago. The coke and calcide formed the bed in the Bruckner furnace, which was rotated at about 1 rpm. The bed was brought to a temperature of about 1800°F by means of an oil flame over the surface. Although results were reasonably satisfactory, they did not warrant full development of the process at that time. A good deal of work has been done in the last 50 years on the production of sponge iron. The objective in some cases has been the production of a precipitant for copper from solution, but the bulk of the work has been done for the production of open-hearth steel furnace stock. The production of an open-hearth stock presents two problems rather than one: first, producticon of the sponge iron, and second, what is perhaps of equal difficulty and importance, conversion of the sponge iron into a form suitable for use in the open-hearth furnace. So far as is known to the writer, none of the sponge iron processes tried in the past have proved to be economically feasible. However, Anaconda had a combination of conditions appearing to justify an attempt to produce sponge iron which would serve for the leach-precipitation-float process. It was thought that the process used in 1914, if changed to a continuous one, might work out satisfactorily. The following favorable conditions at Anaconda justified the investigation: 1—A sufficient tonnage of good grade iron calcine resulting from the roasting of a pyrite concentrate in one of the acid plants, at substantially no cost. 2—Reasonably cheap natural gas. 3-—The fact that there was no need for production of a high grade product. 4— The fact that there was no need for obtaining a consistently high reduction of' the iron in calcine. A small revolving Bruckner-type furnace about 2 ft ID by 4 ft long was set up for early pilot work at the research building. This pilot furnace showed that a satisfactory product could be obtained at reasonable cost. It also indicated a marked advantage in preceding the reduction furnace with a furnace of similar size and capacity for preheating and roasting out any residual sulphur from the feed. The small furnace was operated for several months, various details of the process were worked out. and sponge iron was produced to supply a pilot LPF plant which treated 300 lb of Kelley ore pel- hr. Later a second pilot furnace 5 ft in diam and 12 ft long inside was set up at our reverberatory furnace building. This furnace confirmed the data of the small furnace and gave a basis for design of the final plant. At Anaconda a pyrite concentrate, running about 48 pct S, is recovered from copper concentrator tailings by flotation. This concentrate is roasted to sulphur of 3 pct or less at the Chamber acid plant. The iron calcine contains about 57 pct Fe and 18 pct insoluble. The iron calcine feed, as mentioned before, is re-roasted and preheated in a reroast furnace preceding the reduction furnace. Both are of the Bruckner type. The reroasted calcine is fed into the reduction furnace at 800" to 1000°F along with 30 pct slack coal. In the feed end of the furnace the volatile is burned from the slack, giving a soft coke which readily serves for reduction of the iron. Hard metallurgical coke will not serve the purpose. since it does not reduce CO readily at a temperature of 1850°F. All indications are that the actual reduction of the iron is accomplished by carbon monoxide below the surface of the bed, which is 30 in. deep at its center. Apparently there is a constant interchange: Fe²O³ + 3CO = 2Fe - 3CO², CO² + C = 2CO Actually iron oxide is reduced by CO at somewhat lower temperature than the 1850 °F used in the process. but this temperature is necessary to obtain a satisfactory rate of furnace production. The furnace atmosphere is generally reducing, and typical blue carbon monoxide flames satisfactorily cover the bed. Gas flames from four 3-in. Denver Fire Clay Inspirator burners are played directly on the bed, which is slowly cascaded by the 1 rpm of the furnace. An excess of coke is necessary to assure maintenance of good reducing conditions in the furnace bed. Part of this coke is recovered for re-use.

Jan 1, 1954

By H. W. Imholz

This report covers most of the counties in North Central Texas in which oil is being produced in commercial quantities. The exceptions are McCulloch and Runnels, which were omitted because the production is small and the detailed information necessary for a report is not available to the writer. Complete information was not available regarding the number of wells drilled in this district during the year. The writer wishes to thank Mr. T. F. Petty, of the Humble Oil and Refining Co., Wichita Falls, Texas, for information used in compiling Table 2.

Jan 1, 1937

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10, 1919, to May 10, 1919. BEAVER, JAMES J., Supt., Mech. Ore Loaders, Tennessee Coal, Iron & R.R. Co., Box 62, Bessemer, Ala. BLACKWELDER, ELIOT Geol. & Prof. of Geol., Univ. of Ill., Urbana, Ill. BRAECKE, GUSTAVE E., -Min. Engr., Mgr., Societe Curas et Soldado, La Carolina, Spain. BRINK, CYRIL GORDON, Reduction Officer, Charge of Reduction Works. Fairview Devonian Montrose Gold Mines, Ltd., P. O. Sheba, Transvaal, So. Africa. COMERFORD, JOSEPH S., Chief Chem. & Met., American Manganese Steel Co., New Castle, Delaware. DROSDOWSKI, N. C. V., Asst. Supt.,, The Spassky Copper Mine, Ltd., Karagandy, Akmolinsk, Oblast, Siberia. DUNGLINSON, GEORGE, JR., Asst. to Gen'l Mgr., Norfolk & Western Railroad, Bluefield, W. Va. FARAGHER, PAUL VANCE, Research Fellow on Light Metals, Mellon Institute, Pittsburgh, Pa.

Jan 6, 1919

In an earlier day, a moderate-sized 600 tpd mine could easily require 60 working faces and might use five supervisors. The miner had a tonnage rate as an incentive and was largely his own boss. With the advent of conventional mining machine crews, the typical pattern of resource used changed radically. The number of work places could be cut by a factor of ten, but supervision only by a factor of somewhere around three, or at most, five. Obviously, supervision was increased. Capital use rose at the same time by a factor of approximately eight. Materials used, such as powder and bits, probably in- creased in both quality and unit cost, too. It certainly required a better-trained man to run the machines, but fewer miners were needed. It is clear that each input factor such as land, labor, capital and management, has changed significantly and it would be foolish to attribute all the gain to improved machines. However, concentration of work was a vital consideration in the change, sketched above, and such focusing of work in fewer areas could not have occurred without high capacity mining machines.

Jan 11, 1968

By Michael J. Klishis, Daniel K. Thomas

This paper describes and evaluates factors to be considered in applying computer based instruction (CBI) to the mining industry. CBI is especially suited to the monitoring of training functions and to the delivery of competency-based task training. Its effectiveness is dependent upon: (a) organizational factors (size, number of trainees and trainers, and current training budget), (b) appropriate hardware (accessibility, exclusivity, user-sophistication, transportability, graphics, and cost), and (c) appropriate software (flexibility, response evaluation, video interaction, graphics, and trainee management).

Jan 1, 1983

By Steven Cordiviola, Richard Sergeant

The Kentucky Geological Survey(KGS) was established in 1854 as the official geologic research organization in the Commonwealth. Since that time the Survey has performed basic research in a number of geologic areas such as energy, applied geology, mineral resources, geologic mapping, and hydrogeology. Because of coal's importance to Kentucky, a significant part of the geologic data collected by the KGS is coal related. Coal-related data also occur in a variety of other KGS data sets such as the petroleum and water data files. To adequately respond to coal-related inquiries, the KGS maintains an inter- active, on-line data base in which various types of geologic and hydrologic information can be easily stored, retrieved, and manipulated. The KGS will continue to expand and update this data base through ongoing research, and by cooperating with the Kentucky Natural Resources and Environmental Protection Cabinet, Kentucky Department of Mines and Minerals, U. S. Geological Survey, and University of Kentucky Institute for Mining and Minerals Research. Data in this comprehensive system is available to State, Federal, and local governments; industry; researchers; and the general public. These data facilitate coal exploration, mine planning and permitting, coal production, and research activities in the Commonwealth of Kentucky.

Jan 1, 1983

By S. W. Kennedy, M. Cohen, L. D. Calvert

A high-temperature X-ray diffraction method has been used to study the composition and the kinetics of formation of oxide scales at 800 °C on iron and pure iron-nickel alloys containing 25.6, 75, and 84 pct Ni. This technique has been combined with chemical analysis, and metallographic examination, and determination of weight-gain time curves. The 75 and 84 pct Ni alloys form a three-layer scale consisting of porous NiO next to the metal, a spinel layer, and a -Fe203 on the outside. The 25 pct Ni alloy produces a scale of spinel and Fe,O,, in which, however, traces of FeO and NiO are observed near to the metal. On all the nickel alloys the Fe20, is orieqted with the (107) plane parallel to the surfaces. The exposed surface of the Fe20, is in the form of needles whose axis is perpendicular to the specimen surface. Although the alloys show nonuniform oxidation rates as determined from weight-gain measurements, the X-ray data indicate that the total scale and individml scale layers grow uniformly and parabolically. Deep subscale formation is observed in the 25 pct Ni alloy only. This appeared to be associated with cracking of the scale and penetration of the oxygen along the grain boundaries. ALTHOUGH film formation has been investigated by high-temperature electron-diffraction techniques, for example by Gulbransenl and Hickman,' there have apparently been no investigations of scaling by methods permitting study of the scale during formation at the reaction temperature. Methods involving quenching of scales are based on the working assumption that no significant changes take place on cooling. In general, however, compounds may disproportionate, and the different thermal expansions of constituents may cause disruption of the scale on cooling. In particular, some scales cannot be quenched without spalling. These difficulties are avoided by X-ray diffraction examination at the temperature of formation. High-temperature diffraction procedures also provide a method of determining the kinetics of formation of each phase separately in a multicom-ponent scale. The scaling of binary iron-nickel alloys Containing up to 30 pct Ni at a temperature of 800°C has been studied by Benard and Moreau using cooled specimen~,~ whilst Foley, Druck, and Fryxel14 made an electron-diffraction study of cooled oxide films formed on an iron 42 pci Ni alloy. In the present work the scaling of three iron-nickel alloys containing 25.6, 75, and 84 pct by weight of nickel, at 800°C in oxygen at atmospheric pressure was investigated by X-ray diffraction techniques using a Norelco Geiger-counter diffrac-tometer. The oxidation of iron was investigated for comparison. In addition normal metallographic examinations and chemical and X-ray analyses were made, and weight-gain time curves obtained. EXPERIMENTAL Materials Used—The analyses of the alloys were as follows: Percent by Weight Nickel 25.6 pct 75.4 pct 83.2 pct Aluminum 0.004 None found 0.002 Cobalt — 0.05 0.05 Chromium — — — Silicon — 0.01 None found Carbon All less than 0.05 pct The chemical analysis of the iron was: Al— 0.002 i 0.001 pct, C—0.007 pct, Cr less than 0.001 pct, Cu—0.002 ± 0.001 pct, Mn—0.003 ± 0.001 pct, N—0.0002 pct, 0-0.013 pct, P—less than 0.0002 pct, Pb—not detected, S—0.0017 pct, Si—0.0095 pct, Sn—none detected. This iron was the same as that used to make the alloys and was obtained from the same source-Vacuum Metals Corp. One specimen of pure iron from The British Iron and Steel Research Association was used for preliminary investigation. Specimens were machined to shape from cast rod, polished (the final polish being with 600 Sic paper), degreased in trichlorethylene, washed, and etched. The etching and neutralizing procedure adopted by

Jan 1, 1960

By Bernard Moore

THE last few decades have witnessed the introduction of many new nonmetallic mineral products and changes in the use of many of those already well known. Among these is diatomite, formerly employed as a mild abrasive and, at one time, as the absorbent material in dynamite. Now nearly 100,000 tons a year are mined and milled into such things as filter aids, cement admixtures, insulants, fillers, absorbents, cosmetics, cleansers, etc. Pumice, commonly regarded as only an abrasive, is now also employed as an insulant, as light-weight aggregate and as a concrete admixture. With increasing use of insulants, light-weight aggregates, and acoustic stuccos and plasters in the building trades, both these mate-rials should find increased application. Very large deposits occur in eastern Oregon and have been studied by the U. S. Geological Survey in cooperation with the Oregon State Mining Board.

Jan 1, 1934

Members Dues Resignations, Suspensions and Expulsions Institute Meetings Board of Director?s Meetings Directors and Officers Duties of Officers Committees Nomination and Election of Officers Publications Divisions, Local Sections, Affiliated Societies Amendments [As REVISED FEBRUARY 21, 19281 ARTICLE I MEMBERS-QUALIFICATIONS AND ELECTION , SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Associates; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that Junior Associates, and all Members and Associates whose residence shall be outside of the United States of America, Mexico and Canada shall not be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1928

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer's4 results. The information in Beck's compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas'6 X-ray studies of Jones and Powell's specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

By Frank C. Greene

The wildcatting in northern and northwestern Missouri, which started in 1939, was continued in 1940. Two new gas fields were found and one discovered in 1939 was further extended. The total number of completions was 94, of which 5 were oil wells with about 48 bbl. initial production, 30 were gas wells with an initial open-flow capacity of 37,655,000 cu. ft., and 59 were dry holes. The outstanding discovery was the Polo gas field, T. 55 N., R. 28 and 29 W., in Caldwell County. A sand now believed to be a lens in the Bandera shale at a depth of 400 ft. yielded flows of more than 12,000,-000 cu. ft. In all, I0 wells with 31,490,000 cu. ft. of gas, were drilled. The rock pres-sure is 80 lb. At present no arrangements for an outlet have been made. In Platte County, the Prairie Point gas pool in sec. 7, T. 51 N., R. 33 W., and sec. 12, T. 51 N., R. 34 W., and the Lake-side pool in sees. 5 and 6, T. 50 N., R. 33 W., were further developed, and in the latter both oil and gas have been found, but data are not available for publication at this time. Drilling for gas continued in proven areas in Clay County, and for both oil and gas in proven areas in Jackson and Cass Counties. Table 1 summarizes the results of drilling in Missouri in 1940.

Jan 1, 1941

By Frank C. Greene

The wildcatting in northern and northwestern Missouri, which started in 1939, was continued in 1940. Two new gas fields were found and one discovered in 1939 was further extended. The total number of completions was 94, of which 5 were oil wells with about 48 bbl. initial production, 30 were gas wells with an initial open-flow capacity of 37,655,000 cu. ft., and 59 were dry holes. The outstanding discovery was the Polo gas field, T. 55 N., R. 28 and 29 W., in Caldwell County. A sand now believed to be a lens in the Bandera shale at a depth of 400 ft. yielded flows of more than 12,000,-000 cu. ft. In all, I0 wells with 31,490,000 cu. ft. of gas, were drilled. The rock pres-sure is 80 lb. At present no arrangements for an outlet have been made. In Platte County, the Prairie Point gas pool in sec. 7, T. 51 N., R. 33 W., and sec. 12, T. 51 N., R. 34 W., and the Lake-side pool in sees. 5 and 6, T. 50 N., R. 33 W., were further developed, and in the latter both oil and gas have been found, but data are not available for publication at this time. Drilling for gas continued in proven areas in Clay County, and for both oil and gas in proven areas in Jackson and Cass Counties. Table 1 summarizes the results of drilling in Missouri in 1940.

Jan 1, 1941

By Thomas V. Falkie, Robert Stefanko

Previous articles in this column have defined the manpower situation as it. applies to the coal industry. There is at present a shortage of experienced managers, mining engineers, technicians and skilled workers. The extent of this shortage is controversial, but it is sufficiently important to have received the serious attention of coal industry people at all levels. It has also been discussed by union officials, educators, government agencies and trade publications as well as other communications media. Discussion is not enough, however. A plan of action is needed. Some suggestions for such a plan are presented here. First, the coal industry must interest itself in government training programs. The U.S. Government (primarily the Bureau of Mines and HEW) is planning to spend or is spending millions of dollars to educate and train technicians, inspectors, engineers and miners. The new Federal Health and Safety Academy at Beckley, W. Va., for example, will involve an expenditure of $20-30 million for the physical plant alone. There are encouraging signs that the present hierarchy in the Bureau of Mines intends to seek the advice of mining educators on some of these projects, but industry should also demand a voice in the policy to be followed in making these expenditures.

Jan 1, 1971

By Rex O. McLellan

The formation of a monovacancy in a metal is simulated in an elastic model by the displacement of the surface of a small spherical cavity in a large elastic continuum. The application of linear elasticity to this distortion results in a well- known formula for the energy and an expression for the concomitant entropy change due both to the shear strain in the continuum and also to the dilation of the solid resulting from the boundary conditions at the surface of the solid. Elastic data (the sliear modulus and its temperature coelficient) are used to calculate the entropy and energy of formation for many metals. Despite the simplicity of the assumptions involved, the agreement between the calculated entropies and energies and experimental values is remarkably good. In recent years there has been a large increase in measurements of the absolute concentration of mono-vacancies in metals as a function of temperature. Hence new data for both the energy and the noncon-figurational entropy of formation of monovacancies has become available. Recent measurements&apos; of the anomalous (non-Arrhenius) self-diffusion in many bcc metals has also focused interest on the prediction of the thermodynamic parameters of mono- and multi-vacancies in those metals for which no data are available. Damask and Dienes&apos; have discussed the various theoretical calculations of the energy of formation EL, of a monovacancy. These include simple models involving the breaking of atomic bonds on moving atoms from the interior of a crystal to the surface, models combining elastic calculations with surface-energy terms and detailed quantum mechanical calculations. The simler models give the correct order of magnitude of &, but tend to overestimate it by a factor of about two. The quantum mechanical calculations4"7 have been carried out for the noble and alkali metals with generally reasonably good agreement with the available Ef data. The calculation of entropy of formation Sfv14 lnvolves a fundamental calculation of the perturbation of the phonon spectrum caused by the creation of a vacancy. Huntington, Shirn. and wajda8 have given an approximate evaluation of sJV by considering an Einstein model for the localized vibrations in the immediate neighborhood of the defect and then using elastic theory to calculate the entropy associated with the shear stress field in the distorted crystal (as originally proposed by Zenerg). They also included a term due to the dilation of the crystal. They obtained a value of 1.47k for copper, in good agreement with the experimental value (1.50k). However, Nardelli and Tetta- manzi1° have recently shown that neglecting the coupling between atoms (Einstein Model) may lead to a serious error so the agreement may be somewhat fortuitous. In this work simple linear elastic theory is used to calculate the entropy and energy of formation of mono-vacancies. Despite the simplicity of some of the assumptions involved, the agreement with the available experimental data is remarkable. However. the reasonable degree of success in the application of linear elastic calculations to the excess entropy of a solute atom in a dilute solid solution1&apos; indicates that the application of elastic theory to vacancies. where the interaction of different atomic species is not involved, may not be inappropriate. THE ELASTIC MODEL The metal is assumed to be a spherical elastic continuum. A small spherical cavity of volume V = 4i;v:&apos;/3 is cut from the center. removed. and dissolved rever-sibly in the bulk of the material. TO a good approximation no net atomic bonds are broken and the material does not undergo a volume change although the externally measured volume of the body would increase by V. The radius of the sphere of metal is much larger than r Next a negative pressure is applied to the cavity causing its surface to be displaced inward by an amount simulating the relaxation of the lattice around a monovacancy. In this model the energy and entropy accompanying the distortion are taken as 4, and <. As a first approximation the equation of state for the solid is taken as: r = ro(i + *~D LiJ where K is the bulk modulus. P the hydrostatic pressure. Vo the volume of the material at 0°K and zero pressure. and d+/dT = 30. where 0 is the linear thermal expansion coefficient. The variation of entropy with hydrostatic pressure is given by the Maxwell equation: These equations give the entropy change resulting from increasing the hydrostatic pressure from 0 to P as: and since • we have: This is the entropy arising from the dilation resulting

Jan 1, 1970

NEW MEMBERS The following list comprises the names of those persons who became members during the period of May 10, 1917, to June 10, 1917. ANDERSON, JAMES P.,-Mgr. of the Mines of the Ringwood Co., 50 Church St:, New York, N. Y. BAKER; THOMAS C., Mine Supt., Cia. Santa Gertrudis, S. A. Pachuca, Hidalgo, Mexico. - BARCUS, W. J.. E., Min. Engr., Mining and Metallurgical Dept., General Chemical Co., 25 Broad St., New York,. N. Y. . BENNETT, GEORGE N.,.Min. Engr., Butte & Superior Mining Co., 616 West Gold St., Butte, Mont. BROCKMANN, GUILLERMO, Banker, Gmo. Brockmann & Co., Room 3115, 120 Broadway, New York, N. Y. BROWN, CLYDE L Mining, Box 703, Goldfield, Nev. BRUNSKOG, CARL W., Draftsman, Consolidated Arizona Smelting Co., Humboldt, Ariz. BURRELL,. OSSIAN C Mgr., American Zinc Co. of Tenn., Mascot, Tenn.

Jan 7, 1917

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10, 1916 to Dec.10, 1916. BARNSDALL, THEODORE N., Treas. & Mgr., Highland Gas Co., 24 West Corydon. St., Bradford, Pa. BEASLEY, FRED E., Asst. Supt., Copper Refinery, Consolidated Mining & Smelting Co., Trail, B. C., Canada., BREWSTER, THOMAS T., Vice Pres., Gen. Mgr., Mt. Olive & Staunton Coal CO., 1012 Federal Reserve Bldg.,-St. Louis, Mo. BRINDLE ARTHUR ST. C.... Mining Recorder&apos;s Office, Trout Lake, B. C., Canada. BULLOCK, Harry E., Pres Kentucky-Jewel Coal Co., Lothair, Ky. BUTLER, PERCY BENNETT, Mine Operator :..P. 0. Box 335, Joplin, Mo. BUTLER, ROBERT S Supt., Three Johns Mining CO., ,Joplin,.Mo. CABOT, Godfrey, L., Carbon Black Maker, Gas Engr., 940 Old South Building Boston Mass.

Jan 1, 1917

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Apr. 10, 1918, to May 10, 1918. BALLARD, JOHN I Supt., Cable Mining Corpn., Cable, Mont. BURKMAN, JOHN M. F., Constr. Engr., U. S. Smelt. Refin. & Min. Co., Care -University Club, Mexico City, D. F. CALLEN, ALFRED COPELAND, Head, Mining Engineering Dept., West Virginia University Morgantown, W. Va. CHADWICK, LAWRENCE, Chem., Mt. Elliott Copper Co., Ltd., Selwyn, via Townsville, North Queensland, Australia. CODY, FRANK W., Skimmer, Reverberatory Furnace, Arizona Copper Co., Clifton, Ariz. COOLBAUGH, MELVILLE F., Prof. of Chem., Colorado School of Mines, Golden, Colo. DODGE, ALLAN WAYNE The Dodge Agency, 104 East Iron Ave., Salina, bans. DONNELLY, LEONARD G., Pet. Geol., Sinclair Oil & Gas Co., Sinclair Bldg., Tulsa, Okla.

Jan 6, 1918

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 10, 1916 to Apr. 10, 1916. ALLEN, P. R., Pres., McAlester Coal & Coke Co., Knight Templar Bldg., McAlester, Okla. BERNARD, CLINTON PERCIVAL, Min. Engr., Care Forminiere Mission Kasai, Tschikapa, Congo Belge, W. Africa. CARPENTER, GEORGE 0., Vice-Pres National Lead Co. St. Louis Mo. CLARK, WILLIAM ANDREWS, JR., Min. Engr., Pres., Elm Orlu Mining Co., Butte, Mont. CLAYTON, CHARLES YANCEY, Asst. PrOf. of Metallurgy and Ore Dressing, Missouri School of Mines, Rolla, Mo. COHEN, JULIUS MILTON, Mgr. Croesus Gold Mines, Ltd., Matheson, Ont., Canada. CRAMER, WILLIAM BRONSON, Met. at Concentrator, Old Dominion Copper Min. & Smelt. Co., Globe, Ariz. DAHL, SIMEON H., Mill Supt., Messina Transvaal Dev. Co., Messina, Transvaal S. Africa.

Jan 5, 1916