Search Documents

By Richard Moldenke

ONE of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent., and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly .to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing. 90. per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 percent. of the .charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used.

Jan 2, 1921

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975

By Lewis Delano

IT HAS been generally recognized that, owing to the extreme friability of, galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth retreating today. Investigations of the work of the Hancock jig on the Bonne Terre ore- have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average over all conditions and grades of ore will be between .0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increased smelting charges; due to a greater amount of slime galena will be counterbalanced by the lower operating cost, in-creased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the' St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various flow sheets, and to calculate the economics of the problem' with great accuracy. .

Jan 8, 1920

By Harold M. Mooney

The most significant trends appear to be an increased use of electromagnetic and geochemical methods. The most promising instrumental developments are airborne electromagnetic equipment, a magnetometer based on nuclear resonance, and reflection seismic equipment operable to depths less than 100 ft. Work in progress may lead to a one-man magnetometer capable of high precision and continuous recording.

Jan 3, 1955

By Charles E. Carlsen

Underground construction involves all the legal problems common to the construction industry and adds a nice little group of its own. Elements which will ultimately affect contractor-owner relationship commence to form almost as soon as the owner conceives of the project. A few of these with emphasis on their application to underground construction will be mentioned. (1) During the design stage, determination must be made as to whether the specifications will be general or restrictive. To what extent will the operations of the contractor be controlled? Can he proceed to use any method of tunnel excavation that he desires and only be responsible for the end result or will specific excavation procedures be required? Can explosives be used? Under what restrictions? Are tunnel supports required? How long can the crown behind the heading remain unsupported? What kind of supports are required? What restrictions on the placement of tunnel-lining concrete will be required? Each of you could extend this list for many pages but these illustrations are indicative of decisions that must be made in advance of bidding, and the ultimate decision on each question can have a significant effect on the legal relationships that exist between the contractor and the owner. The owner wants a good job at a fair price. On the other hand, nothing is worse than having a tunnel collapse during the construction period, with its extra costs, loss of life, and delay to the entire project. If the specifications are too restrictive, increased costs of performance are bound to occur. Owners save tremendous amounts of money by obtaining a contractor who has been ingenious in devising the most economical construction procedure. Care must be taken in drafting the specifications so that the benefits of such ingenuity will not be lost. (2) HOW is the contract to be awarded? Will there be open bidding, a restricted list of bidders, or will there be negotiations with a comparatively few contractors? If it is a government project, whether Federal, state, or

Jan 1, 1970

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, all of the following rock types occur; oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently, overblasting wasted drilling time, and explosives caused excessive throw.

Jan 4, 1974

By Oswald J. Heinrich

During the last twenty years much has been done to investigate and define the Mesozoic formatibn of the United States along the Atlantic States, as well as in' the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geologicd surveys of Penn-

Jan 1, 1879

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By H. A. Kuhn

The Pittsburgh coal field in Western Pennsylvania is conceded to be the most important in the world.

Jan 1, 1915

By Dennis V. D’Andrea, Larry R. Fletcher, Peter G. Chamberlain

The evaluation of potential in situ copper leaching deposits requires a thorough examination of the geologic, mineralogic, hydrologic and physiological characteristics of the ore body. The decision to develop the deposit is made with these data along with leaching properties, estimated copper recovery, and economic analysis. A test blast followed by pilot leaching can a so be used for further evaluation and to reduce uncertainty regarding the deposit's potential. This report describes a number of ground characterization techniques that can be used to evaluate potential deposits. Field methods include geologic mapping, groundwater hydrology, core drilling, geophysical logs, permeability testing, and in-situ stress measurements while laboratory tests include assaying, mineralogy, leaching, rock physical properties, size analysis, and computer simulation.

Jan 1, 1980

By K. D. Eigenbrod

A case history is presented of a landslide that occurred adjacent to a highway in the valley of the North Saskatchewan River, about 12 miles upstream of Edmonton, Alberta. The slide took place in the late fall of 1965 following excavations associated with highway improvements that deepened the slope and cut it back to 20º. The slide occurred in the Upper Cretaceous Edmonton Formation. Till covers the bedrock at the location. The bedrock consists of interbedded mudstone, claystone, and sandstone with layers of bentonite and coal. The field investigation consisted of a series of pits at the toe of the slide and seven boreholes around it. Undisturbed samples were taken with a Pitcher Sampler and piezometers were installed at various depths in the section. The slide had taken place on a horizontal bentonitic clay layer and it crossed softened mudstone in the back slope. Three piezometric levels were detected but no water pressures were found along the horizontal portion of the slip surface because it was in contact with a free-draining coal layer. Borehole evidence revealed that the bentonitic clay layer was sheared in place beyond the confines of the slide zone. Although this slide was a first-time occurrence, it was part of a much larger slide block that moved presumably when the valley was being formed. Laboratory tests were carried out to determine the shear strength parameters of the bentonitic clay and the back slope material. These parameters together with the observed water pressure distribution in the slide area gave a factor of safety of 1.01 in a non-circular limiting equilibrium analysis. The case history is particularly instructive in indicating the care that must be taken to obtain representative information for stability analysis when geological and groundwater conditions are non-uniform. The origin of the sheared clay is discussed.

Jan 1, 1972

By J. P. Batcha, J. Robert Denny

Since 1964. Newmont Mining Corp. has been engaged in a systematic research and development of computer techniques for a variety of mine planning applications. The general objective of this effort has been twofold: first, to arrive at a viable near-optimum plan for mining a particular orebody and, second, to decrease the financial investment by reducing the man-hours required for mine planning. Three major phases in the evolution of Newmont's computer techniques for mine planning are discernible. In phase one, the computer's ability to duplicate manual drafting and contour mapping was developed. Obviously, all recognized geologic characteristics had to be included, and consequently the development of computer techniques for the proper incorporation of structure, stratigraphic trends, and other geological features was a significant aspect of phase one.

Jan 1, 1970

Efficient energy utilization in the electrolytic zinc process, relative to other zinc processes, is one of the reasons for its wide adoption in recent years, says John D. Siddle, zinc plant superintendent at the Bunker Hill Co., Kellogg, Idaho. Designers and operators of electrolytic zinc plants have pioneered process improvements, new equipment, and operating techniques to conserve energy. As energy costs increase it the future and competitive pressure mounts against less-efficient producers, these energy-saving improvements will he regarded as necessary for economic survival. Plant designers and operators should not lose sight of the savings in operating costs possible through intelligent utilization of all available forms of energy.

Jan 11, 1977

By Eugene P. Pfleider

Research indicates that the cube diamond is a superior stone for drill bits. It can be oriented to combine a long cutting edge with structural strength and high resistance to wear. Test bits set with preferred orientation give double the bit life at astoundingly low diamond loss in comparison to oriented octahedral diamonds.

Jan 10, 1953

By Bradley Stoughton

[Secretary's Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such 'as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913

By S. H. Ash

Foreman remains key man in any safety program, as men attracted to the industry must be trained in safety thinking. Diesel engines underground aid safety and widespread use of roof bolting is reflected in reduction of roof-fall fatalities.

Jan 2, 1953

By W. F. McDermott

This is the dawning of the computer age in process control. As 1968 drew to a close, many plants had computer installations which were being used for logging, monitoring and reporting. Today, computer usage is given serious consideration before the construction of any major minerals processing plant. Unitized automatic control of individual processes is abundant. Many plants are considering closing these control loops, i.e., allowing the computer to direct the operation of the controllers (Digital Analog Control-DAC). The next step is to make the computer itself the controller (Direct Digital Control-DDC)1 Perhaps the most important future use of computers will be in controlling interrelated operations and control units. Progress along these lines depends on the steadily improving capabilities in the field of mathematical modeling.

Jan 1, 1970

By D. D. Porter, H. G. Carlevato

Blasting to prepare orebodies for in situ leaching usually involves extraordinary conditions which sometimes require special and innovative techniques. To date several unusually large blasts have been made for leaching with results that are very encouraging. Among the factors considered when designing these large blasts are orebody shape and depth, rock properties, vibration and damage potential, loading logistics, and safety. All of these factors, and others, are discussed with an effort made to put each of them into its proper perspective.

Jan 1, 1974

By John S. Sumner

The various electrode arrangements used in induced polarization (IP) surveying can be classified according to the geometry of the electric field being measured. The simplest geometry (Wenner, Schlumberger, gradient) is the parallel or plane-wave electric field, while the three-array and pole-dipole array measure the field about a point current electrode. In the dipole-dipole array the characteristics of a dipolar field are approximately measured. The drill hole arrays employ variations of these fundamental geometries, depending on the objectives of the survey. This report compares the relative advantages and disadvantages of each of the commonly used surface and drill hole IP electrode arrays. Factors of each array that are considered are signal-to-noise ratio, EM coupling rejection, speed and cost, and resolution of polarizable bodies. It is concluded that certain arrays are better suited for different exploration objectives and for different geological conditions. Also the type and capabilities of the IP surveying equipment and method limit the choice of arrays.

Jan 1, 1973

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

A new apparatus termed a "distribution analyzer" is introduced to ascertain the optimum conditions of electrostatic separation of minerals. It was found that with similar surface condition, testing environment and a constant feed rate of not higher than one layer of particles fed on the grounded roll of the separator, the behavior of each component mineral in a synthetic mixture or ore is roughly similar to that of the same mineral when tested alone.

Jan 3, 1950