Search Documents

By E. C. Truesdale

A FEW years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.2 During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. TABLE 1.-Typical Analyses Percentage by Weight Sum of Zinc Pb, Fe, Pb Fe Cd Al Cd Special High Grades 0.007b 0.005b 0.0056 none 0.0106 C.P. (chemically pure) <0.0002 0.0005° 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 6-37). b Maximum. c Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By C. L. Sollenberger, Will Mitchell, Ford F. Miskell

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of&apos; this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of&apos; this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Howard M. Graff, Sidney C. Bouwer

The economics of mining has traditionally been viewed quite apart from the economics of blast furnace operations. It was realized, of course, that blast furnaces would operate best with good raw materials, but the shipping grade of ore, for example, was decided by a sort of collective bargaining process between the ore producers and the blast furnace operators. The mine operators had to keep their costs down, and were usually successful in convincing management that the ore in any particular deposit was endowed by nature with a certain iron content and that the mine grade could not be raised beyond a certain economic limit. The blast furnace operators would have liked a better grade, but as long as they were able to make a fairly good showing it was more or less accepted that they had to take the ore as it came. The mine operators were able to ship to the nation&apos;s blast furnaces thousands of tons of iron ore that would be completely unacceptable by present-day standards. As late as the early 1950&apos;s, the major steel companies were witnessing an actual decline in the iron content of their incoming ore supply as the mining companies mined progressively leaner material and upgraded it only enough to pass competitive market requirements

Jan 8, 1965

By R. Hogg

Sintering is a process in which the pore structure of an agglomerated powder is modified. For many applications, it is desirable to be able to control the pore structure in order to optimize such properties as mechanical strength and reactivity (availability and accessibility of solid surfaces to reactant gases, for example). In general, these properties will be determined by the total porosity and the pore size distribution of the agglomerate. In the work described in this paper, a physically realistic mathematical model for the sintering process has been developed. The model is based on the usual assumption that the pore system in an agglomerate can be treated as a network of interconnecting, cylindrical pores of continuously varying size. It is further assumed that the total pore length is conserved during the course of the sintering process. Using standard expressions for the rate of shrinkage of an individual pore, the model can be used to predict the changes in total porosity and pore size distribution as sintering proceeds. Experimental pore size distributions, obtained by mercury intrusion porosimetry, for the sintering of oxides appear to be in general agreement with the predictions of the model.

Jan 1, 1977

By N. T. Cotman, C. H. Pickering, P. B. Crawford

A beat-conduction model has been developed to study the flow of fluids in a stratified oil reservoir which is being subjected to unsteady-state depletion. To simulate stratification, plates of different metals were joined together so that cross flow could occur between strata. A description of the model, plate construction and necessary instruments is included. The data indicate that stratified oil reservoirs experiencing cross flow may be treated as a single, homogeneous, producing sand having properties intermediate between those of the layers making up the system. A technique for averaging core-analysis data to arrive at the proper average value of rock permeability and porosity is presented INTRODUCTION Although oil has been produced from reservoirs for 100 years and reservoir injection processes have been undertaken for 40 years, the industry is still inadequately informed on the problem of reservoir inhomogeneities. Stratification is perhaps the best-known type of reservoir heterogeneity. Urenl discussed the possible significance of this nonuniformity in his 1927 paper on the theoretical aspects of water flooding. Since this time the problem of vertical permeability variations has been the subject of much discussion and numerous papers. Levorsen2 simply describes the origin of layered beds in his Geology of Petroleum. Some beds are field-wide and may be traced from well to well, while others apparently pinch-out and become discontinuous. In addition, the physical characteristics of a layer may vary from place to place. For these reasons, a stratified system is not easily defined. In calculations involving oil reservoirs in which permeabi1ities vary, methods presently used contain many simplifying assumptions. The reservoir frequently is considered as consisting of permeable layers, each of uniform vertical and lateral permeability and each behaving as if separated from adjacent layers by thin impermeable layers. Other assumptions frequently made in reservoir calculations are steady-state flow conditions, unit mobility ratio, linear geometry, average or homogeneous porosity, and negligible capillary-pressure and gravity effects. Muskat3 has. developed solutions to the stratification problem for mobility ratios other than unity for both linear and exponential permeability distributions. He assumes lateral uniformity and continuity of all productive strata and does not consider porosity. This study will take into account transient effects, cross flow and varying porosity, as well as the variations in permeability, by means of a heat analogy. Muskat5 has shown the similarity of the equations which describe the flow of fluids in a porous medium to the flow of heat through a solid. Landrum, et al,6 made an analogy between the flow of fluid in an unsymmetrical reservoir and the conduction of heat in a similarly shaped metal plate. This analogy is summarized briefly as follows. If fluid is produced from an oil reservoir above the bubble point, the resulting pressure distribution will be identical to the temperature which would result in a metal or heat-conducting plate if heat were similarly removed. This means that a study of heat flow in stratified thermal models will behave like fluid flow in stratified oil reservoirs. For mathematical correspondencies, set- Ref. 6. The fluid mobility k/p is proportional to the thermal conductivity, and the porosity-times-compressibility product is proportional to the density times specific heat of the thermal plate. EXPERIMENTAL EQUIPMENT AND PROCEDURE The stratified reservoir model used in this study is illustrated schematically in Fig. 1. A Leeds and Northrup Speedomax Type G temperature recorder

By G. S. Cole, G. F. Bolling

Recent experitnents on crystal growth have indicated that thermal convection in the liquid influences the conditions of solidification and subsequent crystal characteristics. However, the important columnar-equiaxed transition in castings has not been examined as a function of this free convection. An experiment is presented here to demonstrate a change in the transition as convection is suppressed. Lead- and tin-based alloys were cast in stainless-steel molds either without special procedures or with thin grids placed horizontally across the tnold diameter in portions of the castings. While the grids allowed some diffusion of heat and mass transport to occur during solidification, massive fluid flow was hindered in the vegiotz of the grids. A larger percentage of columnar grains appeared in the grid region than in other parts of the special castings or than in all regions of normal castings. This structural difference can be explained in terms of thermal convection. THERE is little information about the possible effects of natural convection which may occur during the solidification of a casting. Ruddlel-3 has stated that the movement of liquid metal produced by convection might assist in the transfer of heat, but in the absence of confirmatory evidence he suggested that this idea be treated with caution. chalmers4 considers, but does not assess, the importance of fluid motion in casting, while Tiller5 suggests that, in liquid metals which have extremely high thermal diffusivities, the effects of thermal convection may be negligible. In addition, throughout the literature, there are statements indicating the possible presence of thermal convection but without proofs or evaluations of its influence. Natural convection may be divided into two categories: thermal convection, where liquid flow is due to density differences caused by temperature gradients in the liquid (e.g., liquid near a cold wall falling with respect to hotter liquid further away from the wall); and solute convection, where flow is due to density differences as a result of concentration gradients, see Wagner.6 In most instances thermal convection predominates over solute convection. Nevertheless, even thermal convection has not been studied in any detail and is difficult to handle, since it can vary quantitatively from one experiment to another depending upon the exact positions of heat sources and sinks or the attitude of the container with respect to gravity. In spite of these difficulties it is possible to realize that a higher rate of heat transfer must result with convection than in any situation where conduction acts alone. Thus, the degree of increased heat transfer is the important undecided question in considerations of casting. It will be demonstrated here that a reduction in convective flow leads to a suppression of the columnar-equiaxed transition in a casting and that this suppression is related to a decrease in the degree of heat transfer. Fortunately it is possible to do this by comparative rather than quantitative measures. The insertion of horizontal plates or grids into a simple mold does not appreciably influence heat transfer per se, but in reducing the allowable height through which colder liquid may fall freely it reduces natural thermal convection. This leads to a reduced fluid velocity, a different flow pattern, and an altered heat transfer which can be measured. EXPERIMENTS The alloys were prepared from elements of 99.9 pct nominal purity and cast into an uncoated 2-in.-diameter stainless-steel mold insulated at the bottom with a suitable refractory so as to ensure predominantly radial heat flow during freezing. Casting was performed either in empty molds or in molds containing grids or plates in various configurations . The grids were constructed of aluminum screen (1/32 in. thick) which was cut to the desired shape, cleaned in aqua regia, and coated with a mixture of 2 parts aqua dag graphite -1 part Sauereisen cement mixture, thus supplying a hard, protective, and insulating layer approximately 0.006 in. thick. The

Jan 1, 1965

By L. Casagrande, C. O. Brawner, D. L. Pentz, B. Kennedy, E. Hoek, H. Q. Golder, K. Barron

H. L. HAMMERSLEY, B. C. Dept. of Mines. I would like to ask Mr. Brawner if the direction that he measured in the boreholes with the camera was referenced to magnetic north? MR. BRAWNER. Yes, it was. However, there is one problem that you may encounter if the ore body is magnetic; the borehole compass will give erroneous results. Three procedures are available to overcome this. The first one involves the use of a gyro compass instead of a magnetic compass. The second technique developed by Christiansen in Salt Lake City, is to orient the core with the use of scribing knives. The third method is to remove the compass needle and place a steel ball in the compass case. The hole must be drilled at a slight angle off the vertical. The location of the steel ball, which will roll to the underside of the hole is photographed. A borehole directional survey is then made, from which the bearing of the steel ball relative to the axis of the compass can be determined. The joint orientation is then related to this bearing at all depths. J. ROBINSON, B. C. Dept. of Mines. It was stated this morning that there have been some recent developments that give us the ability to drill horizontal drainage holes and install drainage pipes more cheaply than in the past. Would Mr. Brawner tell us some of the new developments and methods of installing these horizontal drain holes? MR. BRAWNER There are two zones in which you may be concerned about installing drains; the first is in the overburden soil, the second is in the rock. Each area requires a different installation method. If the rock is fairly massive and the holes will remain open, the simplest procedure is to use standard air track equipment or a percussion drill. At one of the mines in the Highland Valley, drains up to 300 ft. long have been installed with a percussion drill at a rate of one drain per day. The costs were in the order of $2.30 and $2.40 per foot. If the rock is quite soft, such as in a serpentine, it will be necessary to install a casing in the hole. The least expensive casing that will not deteriorate within the life required should be used. Plastic pipe or black iron pipe are commonly used. In soft rock, it may be necessary to drill with a casing to prevent the col-

Jan 1, 1971

By C. L. Bulow

In this discussion of stress-corrosion cracking of widely used copper-base alloys, no attempt has been made to prepare an extensive review or bibliography since this has been quite ably covered by other investigators. An excellent bibliography was published by H. P. croft(1)2 in connection with his studies of stress-corrosion cracking in mercurous nitrate solutions and his analyses of the magnitude and distribution of stresses in brass parts. We are reporting on a few of the results which have been obtained to date in connection with an ammonia vapor test and an alternate immersion test. These are accelerated corrosion tests for determining the susceptibility of materials to failure from season or stress-corrosion cracking due to the presence of moist ammonia and oxygen so prevalent in nature. Our experiences with the ammonia test seem to indicate that it is a more searching test, than the mercurous nitrate test.

Jan 1, 1945

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established .R3 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resinsmay serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952

By F. S. Jr. Norcross

MANGANESE has long been considered one of the United States&apos; most important strategic raw materials. Its indispensabil-ity in steel manufacture makes it vital to the nation&apos;s industrial life. Coupled with this indispensability is the fact that domes-tic producers have not been able as yet to supply more than a small part of the nation&apos;s manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is con-sumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevail-ing prices.

Jan 1, 1940

By F. S. Jr. Norcross

MANGANESE has long been considered one of the United States&apos; most important strategic raw materials. Its indispensabil-ity in steel manufacture makes it vital to the nation&apos;s industrial life. Coupled with this indispensability is the fact that domes-tic producers have not been able as yet to supply more than a small part of the nation&apos;s manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is con-sumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevail-ing prices.

Jan 1, 1940

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985

By R. L. Blackwood

The solid inclusion cell for absolute in situ stress measurement has been found to give reliable results in coal. The cell is described briefly, along with the methods of installing, overcoring and taking readings in underground coal mines. The validity of the cell performance is demonstrated by reference to the stress-relief curves obtained during overcoring and a three-dimensional B.I.E.M. analysis of the installation to test for stress anomalies deriving from the geometry of the overcoring groove-borehole-cell arrangement. Case studies of two stress measurement projects using the cell are presented for coal mines in New South Wales, Australia.

Jan 1, 1982

• The Venezuelan Trade Mission to the United States announced that Bethlehem Steel Corp. will begin exporting iron ore from its El Pao concession, south of the Orinoco River in Venezuela, in about three months. The ore will be transported by rail from the mines to barges on the Orinoco and transshipped to ore vessels at the coast for shipment to the Sparrows Point, Md., plant. The Latin American business men warned that projected increases in the United States tariff on petroleum imports from Venezuela would force that country into bilateral trade agreements with other countries and would mean drastic curtailment of Venezuelan imports from this country. •Bethlehem, South American Gold and Platinum Co., and U. S. Steel are investigating the possibilities of securing American foodstuff for their South American mining camp commissaries through the International Basic Economy Corp. IBEC buys in quantity to supply its subsidiary companies operating in Venezuela and Brazil. The mining companies will rid themselves of this burdensome task as well as realizing a saving from the bulk purchases of IBEC. •Oliver Iron Mining Co. has begun construction of a fine ore and taconite agglomeration plant at Virginia, Minn. It is expected to be ready in six months. The plant will be used to experiment with the making of clinker cakes and egg-sized lumps by sintering machines and nodulizing kilns respectively; about 1 million tons per year will be produced. • Roof pinning has been adopted at the iron mines of TCI, near Birmingham, to support overlying strata as mining progresses. Favorable results have been obtained in that dilution of the ore has been reduced by 50% which is attributable to this method of supporting the roof. •An American mining engineering team has gone to Turkey for a two-year assignment assisting Turkish government agencies in the $45 million ECA development, mechanization, and construction of cleaning plants for the Zonguldak coal field, 200 miles east of Istanbul on the Black Sea. The group consists of James Beeley, John E. Good, John S. Lambright, David Renshaw, and Charles R. Weir, all of the Paul Weir Co. •Arthur F. Taggart describes a new way of training engineers by emphasis on broad, basic engineering courses on page 460 of this issue. •Lawrence T. Tierney, chairman of the National Bituminous Coal Advisory Council, released a report stating that the increase in oil imports since the latter part of 194$ has caused significant damage to the U. S. fuel economy. It has reduced the strength of and employment opportunities in the coal, domestic petroleum, and transportation industries, as well as in related service and supplier fields. •Women, camels, and donkeys are the beasts of burden of the Sahara, according-to the UNESCO World Review. •Increased demand for magnesium sheet in airplane construction ana other phases of the national security program have led Alcoa to establish a sheet magnesium rolling division at its New Kensington, Pa., works which will begin operation shortly. Novel prospecting methods being used by the USGS in its search for uranium include: shock-mounted instruments in light trucks,. Geiger-counter probes lowered into augur holes, and experimental airborne prospecting.

Jan 4, 1950

By L. L. Handy

Two equations are compared for calculating imbibi-tion rates of water into porous media. A linear relation was found to apply when the square of the volume of water imbibed was plotted against time for water imbibing in natural rock materials. The effect of adsorbed organic materials on surface wettability was determined from measurements of rate of imbibition, water saturation and water permeability. INTRODUCTION An understanding of the mechanisms by which water displaces oil from porous media requires an understanding of the role of capillary forces in the displacement process. The capillary forces are determined by properties of the water-oil-solid surfaces. Consequently, some measure of the surface properties of reservoir rocks is necessary if displacement behavior in oil reservoirs is to be predicted from laboratory measurements. Several experimental procedures have been proposed to assign quantitative wettability indexes to reservoir rock surfaces. The most recent of these proposals are those of Bobek, Mattox and Denekas&apos; and Amott.&apos; These indexes are designed to show a continuous variation from the preferential oil-wet to the preferential water-wet systems. They require measuring some property of the rock which is a function of surface wettability. The quantities are measured on unaltered core material and compared with values obtained for known oil-wet and water-wet extremes on the same material. These methods are useful but are semi-empirical in nature. They have the disadvantage that the measured quantities may be functions of other variables in addition to surface wettability. Some understanding of the behavior of water-oil-rock systems may be obtained from studies of the simpler water-air-rock systems. Surfaces of a given wettability are more easily maintained for the latter. Also, certain approximations can be made for the flow of water and air which are not justified for water-oil flow. The theoretical and experimental work discussed in this paper is part of a study of the role of capillarity in the dynamic displacement of air by water. The expec- tation is that observations for the water-air system will lead to generalizations which are applicable to water-oil systems. THEORY Imbibition is defined as that process by which one fluid displaces another from a porous medium as a result of capillary forces only. Differential equations have been derived to describe the displacement of oil by water during imbibition, but these equations have not been solved.".&apos; With certain assumptions, however, solutions are possible for water-air imbibition.

By J. W. Halley

RIMMING steels derive their name from their action during solidifica-tion in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop ill the molds, are deter-mined by the Composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accu-rately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring condi-tions and furnace practice on the distribution, though there is still much to be done in this direction.

Jan 1, 1938

By Merrill Horine

IT has been stated and accepted for many years that the automotive industry was the instigator, the principal sponsor for and the largest user of alloy steel and nonferrous alloys. The only universally recognized standard specifications and heat-treatments for these materials are those adopted by the Society of Automotive Engineers. It is this same auto-motive industry that has been the chief inspiration for and consumer of modern production machine tools. The production curve of steel ingots is more sensitive to fluctuations in automotive production than any other influence or group of influences. In every other important steel-con-suming industry, automotive materials and automotive processes are the outstanding features of modern progress. In this connection I need only mention the prefabrication of buildings, following the automotive system of straight-line, interchangeable mass production; the motorization of ships and railroads, employing automotive types of prime movers; the production of pressed-steel stoves, plumbing and furniture by methods originated in the automobile-body industry and the extensive use of rubber for the cushioning of all manner of machinery as pioneered by the automotive and tire industries. Dr. Jeffries has brought out this point in his address (p. 21), assuring us that the transportation industry is the largest user of these materials. In the transportation industry, or as we might more accurately express it, the transportation group of industries, the. automotive industry pre-dominates as a user of light alloys. One out of every four tons of aluminum produced is consumed by the automotive industry. Similarly, the automotive industry ranks first in the consumption of the following metallurgical materials: steel, 24.04 per cent; malleable iron, .57; alloy steels, 72.2; nickel, 30; lead, 39 per cent.

Jan 1, 1936

By W. O. Philbrook

ALTHOUGH the actual output of about 89 million tons fell a little short of the hopes and more optimistic predictions of the beginning of 1943, the American iron and steel industry last year produced the record tonnage of its history. It was sufficient to catch up somewhat on the crucial needs for prosecution of the war though an excess of demand over available supply of steel still persists in most categories. It will be necessary during the coming year for the operators to continue to devote all of their efforts and ingenuity to obtaining the utmost tonnage both from existing units and from new facilities still to be brought into production.

Jan 1, 1944