Search Documents

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks.

Jan 1, 1949

By C. L. Colburn

Discovery is the first step in the location of the claim. The provision of the Revised Statutes (2320) is, " No location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located." Strictly speaking, discovery may be defined as the finding of ore or metalliferous rock in place in a well-defined vein. This definition was too strict, so discovery extended later to cover such indications of the pregence of ore, within rock in place, as would justify an experienced miner in spending his time and money with a reasonable expectation of finding ore in paying quantities. According to Colorado statutes a discovery must show a well-defined crevice; in Arizona, a lode, deposit, or mineral in place; in Montana, a well-defined crevice or valuable depositi; in Nevada, a lode or deposit of mineral in place. It is wrong to require a discovery. An honest prospector, wishing to obey the law, finds himself compelled, in most cases, to evade this point. In Clear Creek district, Colorado, a quartz seam will constitute a discovery; in Butte, a red capping; in Leadville or Ely, it is any place where a man can find a piece of vacant ground big enough upon which to sink a . 10-ft. hole. If the vein or deposit outcrops a man can show a discovery, but if it does not outcrop it is foolish to compel him to show one; and this point has been gently side-stepped. Any hole 10 ft. deep now constitutes a discovery. It is no use having laws that the people cannot consistently ob_ey. No sane man will dig unless he expects to find mineral, and he should be protected while digging. He should be required to show that he has mineral ground only when he comes to patent.

Jan 1, 1915

By H. J. French

Within the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about 1/2 to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn. Specialty Tubing The first two classes present mainly mechanical or structural engineering problems. A simple form of tube is made by riveting together the overlapping edges of rolled sheets or plates formed into a cylinder. Because of the nature of its construction, such a tube is necessarily limited to relatively large sizes. Lock-jointed tubing is produced by passing low-carbon strip through a forming machine having suitable rolls and dies, its manufacture is almost entirely a question of design of the forming machine and its satisfactory operation. The chief application of such tubing is in the manufacture of bedsteads.

Jan 1, 1920

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.'' Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By F. D. Rosi, Walter R. Hibbard, R. I. Herron, H. T. Clark, O&apos

Introduction and Previous Work In the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theeretical and practical importance. The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened.

Jan 1, 1949

By Walter R. Hibbard, Robert I. O’Herron, Fred D. Rosi, Howard T. Clark

INTRODUCTION AND PREVIOUS WORK IN the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theoretical and practical importance. [ ] The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened. [ ]

Jan 1, 1948

By C. Richard Tinsley

Non-ferrous econometric metal models available from consultants are reviewed for structure and computer access, using copper as an example The evolution of a computerized metals price forecasting system for a consumer of non-ferrous metals is outlined including front ends, bridge equations, and supporting databases. An empirical sensitivity analysis technique is described. A postscript discusses the subscription costs of these models.

Jan 1, 1977

By Frederick H. McDowell

Notwithstanding the rapidly increasing use of copper, due to the extension of its applications within the last few years, the fact of its continued steady decline in price stands prominently forward. Nor have we far to look for the cause. The opening up of the vast copper-deposits of our Western States and territories is the metallurgical event of the last five years. We must not forget, in looking at the new field, the changed conditions under which the metallurgist must work, as compared with the previous history of copper-smelting. Until quite recently, the copper-plants of the country were few in number; and the concentration of industry implied in this circumstance, allowed many practices which must be considered as inapplicable to the conditions offered at the many mines which have of late become such important factors in our copper-production. Thus the old style of smelting the ore for matte in brick furnaces, involving great expense and time in their construction, while deservedly losing repute even in its old strongholds, in comparison with water-jacketed smelters, is still in some cases adhered to. But to put up such furnaces at Western mines would be out of the question. The large and continual need of brick for relining and repairs acts as an effectual bar, when such furnaces come into competition with the light, portable, and easily managed water-jacketed smelters of improved types. It is owing to the present unusual activity, manifested in the opening up of new copper-properties and the erection of plants for working them, that any improvement in furnace-construction is of especial interest and importance. The method in which processes are copied without variation in the rapid growth of metallurgical interests, has already been strikingly exemplified in the history of

Jan 1, 1885

[ ] John M. Davis has left Western Machinery Co. to take a job as project engineer with Baroid Sales Div., National Lead Co., and is now located at Houston, Texas. C. W. Allen, general manager of the mining dept. of the Cleveland Cliffs Iron Co., visited the firm's iron mines on the Mesabi iron range of Minnesota recently. Thomas P. Anderson, mining engineer and geologist, has resigned from the Raw Materials Div. of the U. S. Atomic Energy Commission where he was assistant chief of the Denver Exploration Branch. He will enter private practice in Golden, Colo. James E. Atkinson, consulting mining engineer and geologist, left New York for Colombia, S. A., as general manager for Cia Minera Choco-Pacifico, S. A., operating five dredges in gold and platinum on the Pacific coast of Colombia. Russell H. Bennett has been elected a director of Placer Development, Ltd. with head office in Vancouver, B. C., and is also a director of its subsidiary, Canadian Exploration, Ltd., which mines and mills lead, zinc, and tungsten ores at a property near Salmo, B. C.

Jan 1, 1952

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By Wilbur Nelson

Little drilling has been done in Kentucky and Tennessee in 1923, with the exception of the Kettle Creek area on the Kentucky-Tennessee line. Oil prices fluctuated between $2.86 and $1.36 Per bbl. for light oil. The Kentucky production was slightly over 8,000,000 bbl., being 1,000,000 bbl. less than during 1922. Tennessee production was approximately 8500 bbl., being a decrease of 1000 bbl, over. 1922. During 1923, the first producing well was brought in, in Clay County, Tenn. Production in Tennessee will undoubtedly increase considerably in 1924, and Kentucky production will probably increase slightly. THE year 1923 has been a dull period in oil development in Kentucky and Tennessee, with the exception of the Kettle Creek area along the Tennessee-Kentucky line, in Clinton and Cumberland Counties, Kentucky, and Clay County, Tennessee. The price of oil during the year has been so low that wildcatters have shown little interest in drilling. At the beginning of the year, light oil sold for $2.31 per barrel and medium oil for $2.06 per, barrel. Prices increased to the highest point for the year in February, when light oil brought $2.86 per barrel and medium oil, $2.61. In April, prices had declined 35 c. while in May an additional decline of 25 c. went into effect. During June, prices declined 20 c. per barrel; during July, 45 c. per barrel; remained stationary during August and September, and dropped during November and December to the low price of $1.36 per barrel for light and $1.21 for medium oil. At present, an increase of 29 c. has brought the price of light oil up to $1.55, and indications are that the price will continue to increase during the coming months. It can readily be seen that during 1923 the price of oil was such as to prevent any drilling except that necessary to hold leases and to maintain production enough to take care of overhead expenses.

Jan 3, 1924

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By H. W. Imholz

Considerable stimulation was given to the interest in the lower producing zones of the North Central Texas area when several wildcat wells developed production in these formations. The Iron Mountain and Humble-Olander well in sec. 196, B.B.B. and C. survey, Jones County, Texas, had a potential of 7500 bbl. (after a 3000-gal. acid treatment) from the Palo Pinto limestone encountered from 3238 to 3250 ft. This well heightened the prospects for oil in commercial quantities in the Canyon, Strawn, Bend and Ellenburger formations in the adjoining counties of Shackelford, Haskell, Throckmorton and others. The Hickok-Van Parmer well in sec. 477 S.P.R.R. Co. survey, Eastland County, Texas, was good for 1040 bbl., natural, from the Ellen-burger limestone, encountered from 4024 to 4033 feet. The Hal Hughes-Cook and Jordan (Poindexter) well in sec. 350, block 6, S.P.R.R. Co. survey, Callahan County, flowed 890 bbl. in 9 hr., after acid treatment, from the Ellenburger limestone, encountered from 4369 to 4388 feet. Both of the Ellenburger wells apparently are maintaining the pressure and volume of their original potential tests, and will no doubt open up considerable area in the adjoining counties for prospecting to the Ellen-burger limestone. Production increased in the district from 12,081,871 bbl. in 1936 to 15,384,500 bbl. The increase was due to developments in Jones and Jack Counties. Jack County production increased from 896,680 bbl. in 1936 to 3,117,063 in 1937, while Jones County increased from 1,596,743 bbl. in 1936 to 2,289,322 in 1937. The remaining counties of the district showed a slight decrease in the amount of oil produced.

Jan 1, 1938

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941