Search Documents

By Lucien Eaton

IN anticipation of a shortage of labor for hand-tram-ming at the Cliffs shaft mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., early in 1923 three 4-ton Goodman storage-battery locomotives, equipped with Edison batteries, were purchased. Storage-battery locomotives were chosen for this work because the expense and time required to put up trolley-wire and to bond the rails of the complicated system of tracks on the levels, where the locomotives were to be used, would not have been warranted by the amount of ,ore to be handled. The only changes in the tracks necessary for storage-battery locomotives were new switches and extra ties and braces on curves. The tracks were 24-in. gage, and were laid with 20-lb. rail. Edison batteries were chosen, because it was desired to charge the batteries from the trolley circuit already, in the mine, and this would have been impracticable with lead batteries. Each locomotive is equipped with 126 A-4 Edison cells, which are charged in series from the 240-volt trolley circuit while the trolley locomotives are running; and are discharged in parallel in two banks of 63 cells each. These locomotives were so successful that later 5 smaller locomotives, weighing 11/2 tons each, were pur-chased for use e with cars that are filled by hand and on levels where the amount of ore handled is small. These locomotives, built by the Geo. D. Whitcomb Co. of Rochelle, Ill., are equipped with batteries of 40 A-4 Edison cells each, the cells being the same as those, on the larger locomotives. They are charged from mer-curial-are rectifiers. These locomotives are operated by the trammers themselves, and have not special oper-ators like the larger machines. The trammers are all young men of American birth, and take quickly to the operation of machinery, and the simplicity of the con-trol on these locomotives has made special training unnecessary. A survey of the results was made by the A. C. Nielsen So., an excerpt from which follows: Eight Edison-equipped battery locomotives are now in use at an Ishpeming mine of the Cleveland-. Cliffs Iron Co. This equipment was installed to take the place of men who formerly pushed loaded cars by hand. Results have been very satisfactory and the de-pendable, trouble-free operation of the Edison batteries is considered to have been an important factor in the effectiveness of the new hauling method.

Jan 3, 1927

By Raymond Moore

THE oil-producing districts of Kansas comprise the northern portion of the so-called Mid-Continent field. As shown in the accompanying map, these districts are located chiefly in the southeastern and south central parts of the state. A considerable area in southeastern Kansas, extending northward nearly to Kansas City, has long been known as oil territory, the productive wells being distributed in patches or spots' of irregular size and shape, the location of which is controlled by conditions of rock structure, and by the texture and porosity of the "sands" beneath: the surface. In south central Kansas, there are a number of producing fields, the location of which appears to be controlled chiefly by well-defined structure. The most important districts are those in Butler County, especially that in the vicinity of El Dorado, which was for a time the most productive district in the entire Mid-Continent field. Recently new production of importance has been brought in the vicinity of Peabody and present development is active to the north across Marion County. Tests in the western parts of Kansas have not been successful in finding new petroleum fields. HISTORY The first well drilled for petroleum, in Kansas, was near the town of Paola, Miami Co., about 40 mi. southwest of Kansas City, in the summer of 1860, only a few months after the completion of the famous "Colonel Drake discovery well in Pennsylvania. Kansas appears to be the second state to engage in a serious attempt to find oil by drilling. The Civil War caused the temporary abandonment, of attempts at oil development in the state.

Jan 2, 1920

By William J. Harris, Morris Cohen

INTRODUCTION THE recent application of lineal analysis1,2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at [M.] and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as "a lowering of [M.], resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (Th) for a sufficient period of time, more austenite may be retained at a given lower or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th, is measured explicitly in terms of the excess austenite [(S)] that exists in the steel at Tr, over and above the amount that is normally present after direct quenching to Tr. Tr is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (Th) may be above or below [M], and still cause stabilization depending upon the chemistry of the austenite. Stabilization has been found to occur in the presence of bainite4 and of martensite5,6,7,8 as well as in the absence of either.9 The phenomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at Th that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subsequent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6.8 low alloy 6.7.8 and high alloy tool steels.10,5 Starting with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1948

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965

By H. S. Rankin

THIS paper is condensed from several reports by members of the staff of the Minerals Testing Laboratory of the Tennessee Valley Author-ity, on a series of experimental tests in the beneficiation of barite of the Valley area. These experiments were conducted upon a large number of samples taken from several mines in three different districts. The area contains numerous producing deposits, nearly all of which are hampered by the high iron and silica content of the ores. Because of the small difference in specific gravity between the iron oxide and the barite, a gravity separation is generally poor. The removal of the iron thus offers a special problem. Some of the operators have turned to magnetic separation to meet the shipping requirements for less than one per cent iron. The present experiments were conducted to determine the application of decrepitation or flotation in simplifying the concentra-tion of the barite by removing the iron oxide and silica in one operation. Practically all the barite marketed in the area has been as "off-color" crude. The bleaching studies were made to determine the bleach-ability of the ores to alleviate this inferior grading, placing them on the market as bleached barite.

Jan 1, 1938

By T. A. Read, M. S. Wechsler, D. S. Lieberman

A theoretical analysis of the austenite-martensite transformation is presented which predicts the habit plane, orientation relationships, and macroscopic distortions from a knowledge only of the crystal structures of the initial and final phases. THIS paper presents a new theory of the formation of martensite. This theory makes possible the calculation of the austenite planes on which the martensite plates form, the orientation relationship between the austenite and martensite crystal axes, and the macroscopic distortions which are observed. The only input data needed are the crystal structures and lattice parameters of the austenite and martensite. Considerable effort has been devoted over the past thirty years to the development of an understanding of the crystallographic features of martensite reactions. Much of this work has been done on steels and iron-nickel alloys, for which a great deal of data has been accumulated concerning the shape and orientation of the martensite plates, the relative orientations of the austenite and martensite crystal axes, and the observable distortions which result from transformation. These observations are reviewed in refs. 1, 2, and 3. The first major step toward an understanding of these phenomena was made in 1924 by Bain,' who showed that the a body-centered cubic structure can be produced from the 7 face-centered cubic structure by a contraction of about 17 pct in the direction of one of the austenite cube axes and an expansion of 12 pct in all directions perpendicular to it. Since that time, most of the efforts at further interpretation have been made by investigators who have worked from the phenomenological data, incorporating some of the information from the lattice properties, and have sought an analysis into likely deformations which would produce the observed results."- "11 but the three most recent papers on the subject have already been reviewed in some detail." Machlin and Cohenl0 measured the components of the distortion matrix and verified that the habit plane is a plane of zero distortion and rotation for the (259) case. They showed that the measured distortion matrix, when applied to the parent lattice, does not yield the product lattice and hence some inhomogeneous distortion must occur. Frank,u working from the lattice properties and taking some clues from the observations, considered the correspondence of close-packed rows and planes in the austenite and martensite. He predicted substantially the observed lattice relationship and habit plane for certain steels which have a (225) habit. Geisler12 suggested that there is a natural tendency for the habit plane to be a (111) and postulated certain slip processes to account for the fact that the experimentally observed habit plane is irrational and deviates from the assumed one. The present work differs from previous treatments of martensite formation in that it permits calculation of all the major manifestations of the process. Habit plane indices, orientation relationships, and observable distortions are all calculated from a knowledge of the crystal structures of the initial and final phases alone. The calculations contain no adjustable parameters. The agreement found between calculated results and the observations reported in the literature constitutes powerful evidence in favor of the mechanism of martensite formation proposed. The theory is applicable to systems other than steel (as is discussed later in this paper) which exhibit a diffusionless phase change but because of the wide-spread interest in the austenite-martensite transformation, particular attention will be given to the iron-base alloys. For other systems which undergo a similar face-centered cubic to face-centered tetragonal transformation, the mathematical treatment is identical with that presented here. Hence the theory successfully describes the transformation in the indium-thallium alloy.'" Homogeneous Transformation to Martensite The distortion which any homogeneously transforming volume of austenite undergoes in order to become martensite is shown in Fig. 1, as was first suggested by Bain.' (This distortion will hereafter be referred to as the "Bain distortion.") This specification of a contraction along one cube axis ;ombined with an expansion in all directions perpendicular to this axis describes what is properly called the "pure" distortion associated with this transformation. The distinction between a "pure" and an "impure" distortion plays an important part in the discussion which follows. A "pure" distortion is characterized by the existence of at least one set of orthogonal axes fixed in the body which are not rotated by the distortion. (These are called the "principal axes" of the distortion.) No such set of axes exists in the case of an "impure" distortion. On the other hand, an impure distortion can always be represented as the result of a pure distortion combined with the rotation of the specimen as a rigid body. For a given impure distortion the corresponding pure distortion

Jan 1, 1954

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

The name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. Geology The ore deposits of copper Mountain are related to the copper Mountain stock, which is an ideal example of the magmatic in in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanies and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial graniti-zation of some of the volcanies. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of Ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. , Theoretical Estimate of Stoping with the Diamond Drill After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1946

By Milnor Roberts

CORNWALL, a Mecca for metal miners the world over, is easily reached from the southern coast of England. Passengers who land at Plymouth or Southampton can connect with a fast train from London called the "Riviera express," which traverses the beautiful counties bordering the English Channel. In Cornwall the traveler soon notices the pits and stock-piles of white china clay, and the metal mines, both placer and hard rock. The deposits are associated with granite batholiths, of which there are four principal ones, each a few miles in diameter. Tin mines are especially worked in the granite near its borders and also in the immediately surrounding Paleozoic slates. Copper and lead are no longer of importance here but tin is being produced steadily from several mines, with arsenic and tungsten as by-products. At the close of the war the man-power available. for these mines had been reduced to one-third of normal, and only now is it again reaching full strength. As mining in Cornwall antedates the Christian era, even a Nevada prospector would have to admit that "she's a permanent camp." SUB-TROPICAL CORNWALL Redruth and Camborne are industrial centers of the tin mining industry, but more tourist hotels are found in neighboring resorts such as St. Ives, a quaint fish-ing town on the Atlantic-side of the peninsula of Corn-wall, where the numerous cats descended from those mentioned in the ancient riddle-rhyme about St. Ives now occupy every doorstep and wall. Another charm-ing resort. Penzance on the shore of the English Channel, is known by name to the public through the opera "The Pirates of Penzance," but is of especial in-terest to students of nature for its palm trees and other subtropical plants, which thrive owing to the nearness of the gulf stream, although the latitude is that of northern Newfoundland, Winnipeg, and the northern end of Vancouver Island. Among the industrial plants at Camborne are those of Holman Brothers, Ltd., where drills and other forms of mining equipment are manufactured. At the Corn-wall School of Mines, which specializes on the district, the staff has assembled excellent collections of local ores, which repay study by a visitor.

Jan 1, 1928

By Robert Ammon

THE purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator, at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 nun. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5-mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0mm. 9. Remarks on the inner feel cone. In the following pages all overflows, are given in quartz dimensions; i.e., by a 0.75-mm. overflow 'is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm.

Jan 8, 1913

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By Geo. H. Ashley

THE present critical state of the supply, distribution, and utilization. of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibituminous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bitumi¬nous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coals by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by, which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service.

Jan 8, 1919

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates are required for certain end uses, and these are produced from smaller colemanite-ulexite-probertite bodies. Sodium-free borate compounds also are produced from boric acid, which can be manufactured from either sodium or nonsodium borate minerals. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of over a million tons of B2O3. Leadership in supplying borates shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates, In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, CA is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, CA, the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "10-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7 • 10H2O. In addition to ship¬ping all major refined borate products from [ ]

Jan 1, 1983

By J. L. Taylor, Pol Duwez

THE present knowledge of the Ti-Al system is limited to the portion of the diagram extending from pure aluminum to the intermetallic compound TiAl3' A preliminary investigation of the titanium-rich Ti-A1 alloys revealed that the solubility of aluminum in titanium is quite extensive and that the transformation temperature of titanium is raised by alloying with aluminum. From an X-ray diffraction study of alloys containing up to 75 atomic pct Al (TiAl3), the phase boundaries at 750°C were located as follows: the a titanium solid solution extends from 0 to about 36 atomic pct Al, a two-phase region exists from 36 to 46 atomic pct Al, and an intermediate phase of varying concentration extends from 46 to 62 atomic pct Al. The purpose of the present paper is to describe the crystal structure of this new phase. The alloys were prepared by melting in a helium arc furnace on a water-cooled copper plate, using a furnace essentially the same as that described in ref. 2. The titanium metal was of the iodide type furnished by the New Jersey Zinc Co., and a piece of pure aluminum (99.99 pct) was obtained through the courtesy of the Aluminum Co. of America. After melting, the samples, weighing approximately 5 g, were sealed in evacuated fused silica tubes and homogenized for 4 hr at 1000°C. The specimens were then held for 10 days at 750°C and rapidly cooled to room temperature. Filings were then taken from each sample, sealed in evacuated vials, annealed at 750°C for 4 hr, and rapidly cooled to room temperature by quenching the vials in water. Powder diffraction patterns were obtained with a 14.32 cm diam camera, using K copper radiation filtered through a nickel foil. Structure Determination The X-ray diffraction patterns of the alloys containing 46, 50, 55. 60, and 62 atomic pct Al were identical, except for a slight shift in the positions of the reflections. The alloy containing 55 atomic pct Al was chosen far structure determination. The powder pattern contained 37 reflections and the a, doublets were well resolved in the back-reflection range. The relatively small number of reflections and the sharpness of the pattern were considered as an indication of a simple atomic arrangement in a relatively small unit cell of high symmetry, and an attempt was therefore made to solve the structure without single crystal work. A satisfactory fit was found on a large scale Hull-Davey tetragonal chart for an axial ratio of approximately 1.45. All the reflections were readily indexed and the tentative unit cell dimensions were computed to be a - 2.81 kX, c - 4.07 kX, and c/a = 1.448. The indices (hkl) and the values of d and sin2 A are given in Table I. The agreement between observed and computed sin2 is quite satisfactory. Once the unit cell was known, the details of the structure were readily found. First, it is obvious that the number of atoms per unit cell cannot exceed two, since more than two atoms would lead to a density greater than that of pure titanium. The next logical step is to assume that the two atoms occupy the corner and center of the cell. If this assumption is correct, the structure may be described as follows: space group D1, - P 4/mmm; one titanium atom in a: 000; one aluminum atom in d: 1/2 1/2 1/2: and no extinctions. Assuming this structure to be the correct one. intensities were computed by means of the usual equation: sin2 0 cos 0 where F is the structure factor; 8, the Bragg angle. and p, the multiplicity factor. The calculated values of intensities are compared in Table I with the visually estimated intensities. The agreement is quite satisfactory and the structure is therefore confirmed. The crystal structure of TiAl just described is the same as that of AuCu ordered. The AuCu ordered

Jan 1, 1953

By A. Lee Barrett

The Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting as a part of this report the second of a series of maintenance cost comparisons. The committee's purpose is to assemble maintenance costs on all equipment connected with mechanical operations at the face of coal mining and to arrange these costs by districts so that comparisons can be made between districts and within districts. The committee, this year, sent 35 questionnaires to representative coal companies who either reported last year or had advised specifically of the inability to report to last year's questionnaire primarily because of limited time. The response to the questionnaire this year as not as good as last year, only 20 of the 35 selected companies returning a completed questionnaire. This year's data have been compiled and combined with last year's data to present a comparison of the 1945 and 1946 costs of loading machines, shortwall cutting machines, universal cutting machines, service locomotives, shuttle cars, and mine cars. The same tabulation by districts is used as was used for 1945. As was indicated by last year's report there is considerable variation in the in cost of mining machinery in the various coal mining districts and due to this high variability it was not felt practical to attempt to arrive at weighted averages. Consequently, all average figures used in this report are straight averages. An analysis was made of companies reporting both this year and last year in an attempt to determine the trend in maintenance costs for different classes of equipment. Ten representative companies are used in this computation. Table I shows the average cost for 1945 and 1946. It is felt that the negative trend in the maintenance cost of universal cutting machines probably represents the effect of the purchase of a relatively large number of new machines in 1946 with little maintenance cost appearing during the first Year of operation. The grand total figure indicates an upward trend amounting to plus 18.7 pet. However, this figure is viewed with some suspicion because of the effect of the universal cutters decreasing maintenance cost and it is concluded that direct application of percentage increase should be made to types of equipment. In Table 2 covering maintenance costs of various types of mining equipment for 1945 and 1946 the results obtained in Table I indicating trends were applied to those

Jan 1, 1949

By Philip W. Henry

There is a difference of opinion among engineers on the subject of depreciation in general, and still more on its application to any given case The committee which was appointed by the American Society of Civil Engineers to make a report on Valuation of Public Utilities, states "There is no subject connected with valuation about which there are more diverse views than those relating to depreciation;" and in the discussion which took place upon the presentation of the preliminary report of this committee in January, 1914, that part of the report dealing with depreciation called forth more discussion than any other. From this discussion it was evident that the word "depreciation" was not always used in the same sense, so it is quite important that some definition be adopted. As this paper relates to the proper method of treating depreciation by corporations or individuals operating oil properties, both of which must make a return of annual net income to the government in connection with the income tax, it will be in order to adopt the definition of the Internal Revenue Bureau. Under date of Mar. 29, 1910, the Commissioner of Internal Revenue of the Treasury Department stated "Deduction on account of depreciation of property must be based on lifetime of property, its cost, value and use." Again, on Form 1035, "Return of Annual Net Income" for miscellaneous corporations (Section 2, Act of Congress approved Oct. 3, 1913), a deduction from gross income is allowed for "Total amount of depreciation for the year." This item is defined more particularly as follows: "The amount claimed under Item No. 5 (b) for depreciation should be such an amount as measures the loss which the corporation actually sustains during the year in the value of buildings, machinery, and such other property as is subject to depreciation on account of wear and tear, exhaustion, or obsolescence. The amount taken credit for on this account in order to be allowable should be so entered on the books as to constitute a liability against the assets of the corporation. The amount claimed under this item should not cover losses in the value of stocks and bonds. Decrease in the book value of securities owned, so far as such decrease represents a decline in the actual value of such securities, should be deducted under item 5 (a) of the return. "Where depreciation of physical property is made good by renewals, replacements,

Jan 1, 1915

By J. P. Doan, G. Ansel

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

By J. P. Kimball

INCIDENTAL to a description of the hytlrographical basin of the Quemahoning in Somerset county, Pa., as a coal-field, I have, without a personal survey of the whole county, taken the pains to collate a synopsis of' leading facts, so car as available, relating to its coal resources. This is here presented, in view of an interest in the subject, growing out of a nearly central traverse of the county, in common with the southern tier of counties of the State, west of Blue mountain, by a new trunk line of railway—the South Pennsylvania. The political east-and-west boundaries of Somerset county, Pa., following the bold topography of Allegheny mountain and Laurel hill, are in common with the east-and-west boundaries of the First Bituminous Coal-basin formed by these ridges respectively, except the southeastern townships which lie on the eastern slope of Allegheny mountain. The nearly parallel anticlinals of Negro mountain and the so-called Viaduct axis stratigraphically divide the basin into three sub-basins, which, in order from east to west, are known as follows, viz. : I. Berlin-Salisbury (Eustern) Sub-basin : Between Allegheny mountain and Negro mountain, embracing the Berlin section of Barren coal-measures, the Salisbury section of Upper Productive coal-measures, and the Meyersdale and Garrett sections of Lower Productive coal-measures. 11. Somerset (Middle) Sub-basin: Between Kegro mauntain and the Viaduct axis, so called from the viaduct on the Conemaugh river, which there crosses it; embracing the section of Lower Productive measures of Mineral Point and Casselman on Castlenlan river, and of Somerset. 111. Johnstown- Confluence (Western) Sub-basin: Between the Viaduct stratigraphical sub-axis (which is less strongly marked topograpically in Somerset county as a ridge than in Cambria county), and the Laurel Hill graud axis. The synclinal of this sub-basin is crossed by tile Conemaugh near Johnstown, and by the Castleman

Jan 1, 1884