Search Documents

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By Gerhard Derge

A SERIES of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the International Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.1 There is little information available regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which more exhaustive experimental work may be done to best advantage. EXPERIMENTAL PROCEDURE The first work was devoted entirely to the problem of obtaining reproducible results from a series of potential measurements. Only the methods finally adopted as standard will be described here, except when the variations from these have furnished results of interest. The cell used is shown schematically in Fig. 1. The electrolyte is contained in the vessel A (an inverted bell jar), whose ground top is fitted to the transite-board lid B. The controlled atmosphere can be admitted

Jan 1, 1938

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By C. F. Rust

Experimental evidence is presented showing that reproducible formation resistivity factor measurements and resistivity index determinations on reservoir core samples map be made utilizing either the two- or four-electrode methods. Equipment is described which permits the application of either technique to the core specimen without loss of time and with a minimum amount of effort. Since electrical resistivity measurements on reservoir rocks are important not only in electric log interpretations, but also in the study of fundamental rock parameters, it was considered desirable to compare the applicability of both techniques of resistivity measurement. INTRODUCTION The techniques employed in the measurement of electrical resistivity on reservoir rocks, as practiced in the petroleum industry, may be reduced to two fundamental methods: one utilizing two electrodes only, usually referred to as the two-electrode method; the other using two additional electrodes and commonly known as the four-electrode method. In the former, the core sample whose resistivity is to be measured is mounted between two electrodes, usually metal discs, which serve to pass a current of known magnitude through the saniple. The potential drop across the sample, measured between these same two electrodes, and the core dimensions furnish the necessary data to compute he resistivity of the sample. In the four-electrode technique the end plates, again usually ol metal, still serve as current electrodes. Additional probes or electrodes dispersed along the sample are utilized to measure the potential drop. Both methods are used in practice1,2 and it is the purpose of this paper to compare the two techniques as applied to the determination of formation reiistivity factors and the resistivity index exponent n, in Archie's empirical equation I = p/po = Sw 11. To evaluate the two techniques it is desirable to point out the experimental precautions which must be taken to insure reliable results. It is evident from the electrode arrangements of the two- and the four-electrode methods that, for a given sample, the volume of sample included by the four-electrode method is less than the volume included by the two-electrode method. One of the prime difficulties associated with the two-electrode method is the possible occurrence of an abnormally high resistance between the electrodes and the brine-saturated sample, which results in erroneous resistivity values for the core sample itself. Attempts to alleviate this difficulty meet varying degrees of success. Methods used in the past employ such absorbent materials as brine-saturated Kleenex: chamois, or felt. A technique described by Morgan, Wyllie, and Fulton,1 appears to be more satisfactory. Their method consists of spraying or painting the end areas of a core sample with conductive silver paint. This technique reduces contact resistances between the porous medium and the electrodes to a value which is generally negligible as compared to the resistance of the sample itself. In the four-electrode method these requirements are not as stringent since separate probes are used to measure the potential difference acrozs a portion of the sample. In this case, contact resistance occurring at the current electrode; are of no consequence. and those appearing at the potential

Jan 1, 1952

By Raymond Mancha

WHEN calculating the pressure-volume characteristics of projected mine-ventilat-ing circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption suffi-ciently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the vari-ous intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pres-sure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individ-ual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differ-ences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from out-bye to inbye the circuit.

Jan 1, 1940

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By D. Walton, B. Chalmers

A preferred orientation is known to occur frequently in the columnar zone of castings. This has been attributed to a preferred direction of growth. However, no satisfactory mechanism was proposed by which the preferred direction of growth led to the preferred orientation. The purpose of this work has been to establish this mechanism. It has been found that in general the observed preferred orientations only develop when the preferred directions of growth reveal themselves by dendritic growth. A mechanism based on this premise is found to be in agreement with the experimental data obtained in the course of this work. WHEN a liquid metal is allowed to solidify in a mold, it usually freezes in three stages, distinguished from each other by the size and shape of the grains. The first zone to freeze (the chill zone near the mold wall) consists of relatively fine grains that are equiaxed in shape and random in orientation. The next zone consists of crystals that are elongated in the direction of heat flow, i.e., normal to mold wall. These crystals are much larger in cross section than the crystals of the chill zone and have a very strongly preferred orientation. This is the columnar zone. The final zone, which is absent in very pure metals, is again equiaxed and randomly oriented, but usually has a much coarser grain size than the chill zone. The purpose of this study is to describe and account for the crystal size and orientation in the columnar zone. The occurrence of a preferred orientation in the columnar zone is well known, and in 1940, Greninger' suggested that it is apparently related to dendritic growth although at that time the only data were for metals with the face-centered-cubic structure. Table I shows that the direction of dendritic growth and the crystal axis that follows the heat flow direction coincide in all cases so far studied. The term "dendritic growth" is used here to represent the branched type of morphology that is characteristic of growth into supercooled melts.' In addition to the supercooling which is necessary before nucleation will occur at the mold wall, the necessary supercooling for continued dendritic growth can be provided in a mold by heat flow into the already formed solid at an interface whose Liquidus temperature is depressed by an accumula-

Jan 1, 1960

By J. W. Smith

Our continuous search for underground productivity improvements has been brought about by the diminishing ore grades in existing underground mines. The need for more efficient mining methods is a result of the economic problems facing our industry today, and this has caused us to evaluate underground haulage methods which have traditionally been the "bottleneck" in the flow of material from the ore in the natural state to the surface processing facility of any underground mining operation. Small improvements in the face haulage systems have yielded much greater benefits as they relate to overall mine productivity so it's only natural that we are all concerned with the best method of moving ore from the face to the main line haulage. In a recent paper titled "Underground Haulage Trucks - Gaining Momentum Worldwide", Richard A. Thomas concludes that the use of trucks to haul ores in underground mines is on the increase spurred by the convergence of a number of technology advances and economic realities. Perhaps the most important stimulus for the growth of trackless haulage is the high degree of haulage flexibility in underground operations. On the economic side, the demand for higher productivity from underground mines has resulted in larger physical dimensions of haulage roads, that is, higher backs and wider drifts to provide more room for high capacity haulage units. In the process of determining the most effective type of equipment for haulage, the power source must be a major consideration. For the purpose of this paper, we will limit the comparison to rubber-tired trackless haulage vehicles and not try to make a comparison between rubber-tired haulage, continuous haulage systems and rail-mounted haulage. Cost is perhaps the only really measurable factor when making a comparison between electric and diesel haulage. You will find that some costs will be very well defined in absolute terms. In other areas of comparison, cost can be fairly well estimated, and yet in still others, the costs are totally arbitrary. Let's take a look at some of the cost considerations. (Figure 1) first of all, is the initial cost of the equipment. This capital cost quite often is a determining factor in the type of haulage vehicle to be selected, yet this initial cost is perhaps the most insignificant of all costs when evaluating an operation over the long term. Of much greater concern, is the cost of maintenance. This cost will often run three times the original capital investment during the life of a single piece of haulage equipment. This factor can include rebuild to extend the life of the original capital investment, but certainly includes the labor and materials necessary, plus the inventory to keep the equipment in good repair. Perhaps one cost which is now playing an even greater role in the rubber-tired haulage operation, is the cost of fuel. Conoco has recently come up with some rough estimates which indicate that diesel fuel will cost an average of three times the equivalent kilowatt output in direct electric power. Diesel fuel is almost twice the cost of stored electric power. (This of course relates to the efficiencies of charging and recovery of power from lead acid storage cells.) These particular figures of course will vary from one area to another but I think that there is enough significance here to certainly warrant the further study of fuel costs for each particular area or mine. Another cost is breakdown expense. This must be treated differently from maintenance costs because a potentially larger expense is involved, more than just parts and labor. Now we have to deal with the cost of lost production time, which can have a much greater overall effect. Mine plan economics are another cost consideration where we can't make a comparison without looking at specifics. Here you must look at the movement of power centers vs. the flexibility and freedom of movement of vehicles. The determination must be made as to what types of equipment will fit into any predetermined mine plan and if a change in the planned roadway dimensions for the mine plan itself would be more economical so that more efficient type of equipment could be utilized. Finally, two of the most important aspects to be considered with potential ramifications far beyond what we have mentioned previously, is the cost of health and safety, which is really the cost of meeting current and future government regulations, reasonable or otherwise. And of course, when making any consideration here it is impossible to come up with anything more than an educated guess on the cost of meeting the new regulations. Now let's take a look at some of the advantages of diesel vehicles as well as advantages offered by electric vehicles, both battery and cable powered versions (Figure 2). Much of the data used in this comparison is based on experience with three vehicles manufactured by Jeffrey Mining Machinery Division, Dresser Industries. Jeffrey manufactures all three types, each with approximately a 15-ton capacity, even though few of these Jeffrey vehicles are used in uranium mining operations. Much of our experience comes from the 4114 diesel powered RAMCAR which is a 4-wheel drive, articulated steering,vehicle powered by a Caterpillar 3306NA engine and using a powershift transmission. This will be compared with the performance of the Jeffrey 404H battery powered RAMCAR with articulated steering which utilizes a separate 35 HP DC drive motor on each of two wheels with solid-state speed controls, and the final comparison will be made on the Jeffrey 4015 cable-reel shuttle car which is powered by two 60 HP constant

Jan 1, 1982

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By W. W. Stephens, W. J. Kroll, H. P. Holmes

THE only two methods for producing commercial quantities of malleable zirconium, up to now, have been using magnesium reduction of the anhydrous chloride under a neutral gas, and using purification of raw zirconium by the iodide dissociation method on a hot filament. The purity of the metal obtained by the latter process is about the same as that resulting from the chloride reduction, with the exception of the oxygen content, which may be about 0.05 pct lower in the iodide metal. Even traces of oxygen have a strong hardening effect on zirconium. Since, in the iodide process, the impurities, Si, Al, Fe, Ni, and Mg in the raw zirconium used, are carried over, it would appear uneconomical to use this method of refining solely to eliminate the traces of oxygen, unless very soft metal is desired. One important step to improve the iodide method, namely, dissociating pure iodide made from carbide and recycling the iodine, which would change this refining process into a method for extracting zirconium from the ore, has not yet been made. The Bureau of Mines, by using the chloride reduction, wanted to produce quantities of a reasonably pure and malleable metal at low cost for large-scale industrial use. This aim has been achieved, and a pilot plant permitting production of 600 lb of malleable zirconium per week will be described (fig. 1). Briefly, the Bureau of Mines process consists of reducing purified gaseous anhydrous zirconium chloride with fused magnesium under a noble-gas atmosphere. The reaction product, magnesium chloride, and any excess magnesium metal present are removed from the sponge zirconium in the next step by fusion and evaporation in a good vacuum at about 925°C. In this process, care is taken to keep air out of contact with the hot metal, which otherwise would contaminate the product with oxygen and nitrogen. Both these impurities embrittle zirconium even when present in an amount as low as 0.1 pct. A number of previous reports1-3 describe the method and the various improvements that finally led to a workable process. The major steps made were the production of large quantities of carbide, which is the raw material for producing the chloride, its chlorination with reasonable efficiencies, and the elimination of iron trichloride contained in the raw chloride, as well as that of the zirconium oxide which is always present in this product. The physical nature of the anhydrous chloride, which sublimes at 331°C at atmospheric pressure and melts at 420°C under a pressure of 25 atm, made it necessary to provide a special safety device on the purification and reduction vessels in the form of a lead-alloy seal, permitting escape of excess gases if pressure tended to build up. The main difficulties encountered in the reduction and in the following step, salt separation in a vacuum at elevated temperature, were caused by the material from which the reaction pot was constructed—iron. This metal reacts with zirconium at about 940°C with formation of a eutectic. The last step, salt separation by evaporation of the magnesium and magnesium chloride in a vacuum, is quite unconventional and has not been used before on such a scale. It is only due to the improved construction of high-vacuum pumps, especially oil-diffusion pumps, that such a method could be used. The various steps of the Bureau of Mines process, as described in the general outline above, may be summarized as follows: (1) production of the carbide, (2) chlorination of the carbide, (3) purification of the raw chloride, (4) reduction of the pure chloride with fused magnesium, (5) separation of excess magnesium and magnesium chloride in vacuum at elevated temperature, and (6) melting of the sponge obtained. Production of Carbide The arc furnace, described in a previous report,' was improved both to reduce the graphite consumption caused by the burning of the bottom plates and to concentrate the heat in order to obtain better power efficiency. This was achieved by providing the bottom with graphite plates entirely embedded in refractory bricks, the contact with the current being made with three water-cooled copper plugs. Figs. 2 and 3 show the arrangement. The crucible, made

Jan 1, 1951

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By Prof John E. Church

It is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By M. M. Mebta, G. W. Dean, W. H. Somerton

With the advent of underground heating operations, interest has developed in the alteration of rock properties by high-temperature treatment. In the present work a number of sandstones were heated to temperatures in the range of 400°C to 800°C under both atmospheric and simulated reservoir pressures. Pertneabilities increased by at least 50 per cent and sonic velocities and breaking strerlgths decreased by an equivalent amount. Differential thermal expansion and other reactions of constituent min-era1 grains are the causes of these alterations. INTRODUCTION In the underground combustion of petroleum reservoirs, temperatures of the order of 600C are reported to have been reached in the combustion zone.' At this temperature rocks are subject to extensive thermal alteration. Temperatures of this magnitude and higher may also occur in subsurface formations when subjected to bottom-hole heating, thermal drilling operations, and underground nuclear explosions. Temperatures of this magnitude might also be generated by conventional rock drilling methods at points of bit-tooth contact. In earlier work, the permanent deformation of rocks resulting from heating was reported. Major structural damage of rocks occurs due to differential thermal expansion of mineral constituents. A number of mineral alterations including crystal inversions, loss of water of crystallization and dissociation, may also contribute to changes in physical structure and properties of rock. In the present work, samples of three typical sandstones were heated to several temperatures up to a maximum of 800C and then allowed to cool to room temperature. Heating was done under both atmospheric pressure and simulated reservoir pressure conditions. Physical properties of the samples were measured before and after heating and comparisons made. Measured properties included permeability, sonic velocity, breaking strength and fracture index. Changes in physical properties were compared to changes in mineralogical characteristics as determined by thin-section. X-ray diffraction and chemical tests. EQUIPMENT AND PROCEDURE Two outcrop sandstones (Bandera and Berea) and one sub-surface sandstone (St. Peter) were selected for the tests. These samples have a wide ranee in composition and physical properties as shown in Table 1. The first series of tests was made on 2-in. diameter by 5-in. long test specimens. Test specimens used in all later work were 3/4-in. diameter by 1 1/8-in. long, this being the specimen size required for heating at simulated reservoir pressures. After careful washing, the cores were oven dried at 100 ± 5C for a minimum of 24 hours before the tests were run. Test specimens were heated in an electric furnace at a constant rate of temperature increase of 3C per minute. When maximum temperature of the run was reached, the sample was allowed to soak for one hour. The furnace was then cooled to room temperature at the same rate of 3C per minute. The entire heating operation was designed for reproducibility without subjecting the test specimens to excessive thermal shock. For samples heated under simulated reservoir pressures, a pressure cell designed by Dean was used (Fig. 1).3 The core sample was inserted into a thin-walled (0.006 to 0.01-in.) copper cup which was then mounted in a high-pressure cell. Provisions were made for the application of internal pore pressure as well as confining pressure. Tests showed that the thin-walled copper cup closed tightly around the core and satisfactorily transmitted confining pressure to the core. The core was heated by placing the entire cell into the electric furnace. The heating program was the same as that used in the atmospheric pressure runs: tempera-ture rise of 3C per minute to maximum temperature of the test, soaking at maximum temperature for one hour, and cooling at a rate of approximately 3C per minute. The cell was designed to withstand 5,000 psi at 1,000C. However, since it was considered likely that repeated heating and cooling would in time weaken the steel, 2,000 psi at 850C was set as a working limit. In the present series of tests, the pore pressure was held constant at 750 psi and the confining pressure at 1.500 psi. The pressure source was a high-pressure nitrogen tank. The two pressures were controlled manually but are accurate well within ± 50 psi.

Jan 1, 1966

By AIME AIME

THE ninth International Petroleum Exposition held at Tulsa, May 16-23, broke all size, sales, and attendance records of previous shows. More than $12,500,000 worth of equipment was on the grounds. There were 546 companies exhibiting and every available inch of the fifteen acres allotted to exhibit was taken. Drake Drive, the main street of the exposition, was literally "supply row" with National Supply, Frick-Reid, Continental Supply, Oil Well, Bridgeport, International Derrick and Equipment, and Parkersburg Rig and Reel companies occupying the entire space. The exhibitors were a cross section of American industry, with such firms, besides the strictly oil equipment firms, as the United States Steel Corp. and others allied to the oil industry, exhibiting. Between $10,000,000 and $15,000,000 of equipment is estimated to have been sold on the grounds during the exposition. Valuable contacts were made by the exhibitors with key oil men. Attendance passed the 175,000 mark for paid admissions in contrast with 154,000 for the eighth exposition in 1934. Visitors registered from Venezuela, Soviet Russia, India, Germany, Spain, Mexico, England, Canada, France, Colombia, Greece, West Indies, and Rumania. Hotels were overflowed and a housing bureau found rooms in private homes for thousands. Oil companies set up a schedule of shifts in order that as many of their field men might attend as possible. It is said that the companies want a two-weeks' show in 1938 so that more time will be avail-

Jan 1, 1936

By W. M. Albrecht, M. W. Mallett

The solubilities of hydrogen in titanium and several of its alloys were determined at 600 to 1000°C and pressures of 0.05 to 10µ of mercury. Solubility increases with increasing beta phase in the alloys. Factors found to affect degassing rates are specimen size and presence of thick surficial oxide. Removal of hydrogen by heating in vacuum and in flowing inert atmospheres was studied. Practical curves predicting minimum degassing times are presented. THE presence of hydrogen in titanium and titanium alloys has detrimental effects on the mechanical properties of the metal.'"," The hydrogen content of commercial titanium is sometimes of the order of 200 ppm by weight' and varies with alloy composition. As a consequence, titanium and some titanium alloys as normally processed are sometimes not ductile unless treated to lower the hydrogen content. The best known hydrogen-removal treatment is heating the material in a vacuum. The rate of removal (degassing) at a give temperature determines the duration of the treatment required to attain a satisfactory low hydrogen level.

Jan 1, 1959

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923