Search Documents

By J. Sibakin, R. D. Hindson

In order to devise a practicable soaking pit schedule for use at The Steel Co. of Canada Ltd.'s Hamilton Works, soaking pit heating temperatures, sooking times, pit capacity, and safe maximum mill drafts were correlated with fluctuations in the current or load of the bloom mill driving motor. Other variables such as total delays in the pit, rolling schedules, mill delays, and track times were also investigated. IN order to show an easily applied and accurate means of establishing soaking pit heating temperatures, soaking times, pit capacity, and safe maximum mill drafts, these various factors are correlated herein with fluctuations in the current or load of the bloom mill driving motor. Rolling practices have a considerable influence on the production capacity of a blooming mill. The maximum values of the torque, in particular, are of importance, since even instantaneous current peaks lead to the tripping of the motor by the overload relay and result in loss of mill time. The establishment of safe maximum drafts and accelerations for ingots of different sizes and of a soaking pit practice which would ensure a consistent and satisfactory plasticity of the metal is of considerable importance for increasing the efficiency of both the blooming mill and the soaking pits. The Bloom Mill Dept. of the Hamilton Works, The Steel Co. of Canada Ltd., is equipped with one 44 in. mill driven by a 7000 hp motor with the setting of the overload relay at 22.0 ka. The speed of rotation of the motor is regulated after the Ward-Leonard system. There are three basic speeds of 9.5, 28, and 47 rpm and a further possibility of increasing the speed by weakening the field. This last possibility is hardly ever used during practical operations. The rolling program of the blooming mill is varied, both in the size of the ingots to be handled and in the steel grades. The total tonnage handled by the mill is about 2,000,000 ingot tons per year. At the time of the investigation, the Bloom Mill Dept. was equipped with 22 soaking pits (6 regenerative, 14 bottom-fired, and 2 one-way top-fired pits) with a total bottom area of 2770 sq ft. The pits are fired with a blast furnace-coke oven gas mixture having a calorific value of 155 Btu per cu ft. The foregoing figures show that the production program was such as to impose the necessity of a most efficient usage of the available equipment. For this purpose, the operations of the 44 in. mill and of the soaking pits were investigated, and the results of the investigation were used as a basis for a revised soaking pit schedule and drafting practice. The plasticity of an ingot of a certain chemical composition when being rolled is determined mainly by the following factors: I—the ingot size, both thickness and width; 2—the length of the gas soak; and 3—the surface temperature. The first two factors determine the uniformity of the temperature distribution over the cross-section of an ingot. The third factor introduces the level of the heating of an ingot. The torque produced by an ingot being rolled is determined by the area of the metal displaced, its plasticity, and acceleration values. On the other hand, with shunt motors the torque is determined by the current. This can be assumed to be correct with only a small degree of error for compound motors with a relatively small effect of the series windings as long as the velocity is not regulated by weakening the field. Since the spread is relatively unimportant when compared to the width of an ingot and since it is also reduced several times during rolling by edging passes, the draft alone and not the area of the metal displaced may be taken into consideration with ingots of a similar size. It is therefore possible to determine the main features of the heating and drafting of an ingot by measuring the current and acceleration of the mill motor. After the acceleration has been taken into account, the amount of current will be an indication of how the motor responds to a heating and/or drafting practice and these practices can be adjusted in order to get the desired result. As peak currents are more likely when heavier ingots are rolled, the rolling of plate and slab ingots was investigated. Conditions prevailing when smaller ingots are rolled can be deduced from the results obtained on heavier ingots. All measurements were made when plain carbon grades under 0.15 pct C were rolled. The motor current, the voltage across the armature, and the rpm were recorded simultaneously on synchronized charts, Fig. 1, which moved with the speed of 6 in. per min. Each draft was recorded by a special observer. The rpm curve made it possible to establish the acceleration at any given moment. For purposes of correlation, the maximum current during a pass and the corresponding acceleration were used. The charts made it possible to establish the position of the roller's lever at any given moment as well as the total time of a pass. The slab ingots were divided into three groups (28x35, 28x45, and 27Mx53 in. ingots) and each group was investigated separately. Since they account for most of the current peaks, only flat passes were used for purposes of correlation, a total of 1373 having been investigated.

Jan 1, 1956

By D. G. Westlake, D. T. Peterson

The saturation solubility of thorium dihydride in thorium was studied by saturation of samples and subsequent analysis. The solubility increased from about 1 at. pct at 300°C to above 20 at. pct at 800 °C. Over this temperature range the log of the solubility was a linear function of the reciprocal absolute temperature for thorium of good purity. The heat of solution of thorium dihydride was found to be 7.9 kcal per atom of hydrogen in crystal bar thorium and 6.6 kcal per atom of hydrogen in Ames thorium, The important effect of hydrogen on the physical and mechanical properties of many metals is receiving increasing recognition. The basic physical and chemical data necessary to help explain the observed effects of hydrogen on the mechanical proper ties of metals are all too often not available. The solubility of hydrogen in thorium metal was determined to provide a portion of this basic data for the thorium-hydrogen system. The absorption of hydrogen by thorium metal and the formation of thorium hydrides was studied by several investigators, beginning in 1891, and their work is summarized in Gmelin's Handbuch.1 No effort was made to determine the extent of solid solubility in the metal in these early investigations and the impure metal available made interpretation of the results uncertain. Nottorf2 reported the results of a careful study of pressure-composition isotherms for the thorium-hydrogen system. The principal interest in this work was in the composition and dissociation pressures of the thorium hydrides. Mallett and campbel13 reported the pressure-composition isotherms for the thorium-hydrogen system up to the composition of thorium dihydride. The saturation solubility of thorium dihydride in thorium was reported to be 13 at. pct at 650°C and 23 at. pct at about 900° C. Mallett and Campbell used thorium metal which had been prepared by the calcium reduction of thorium tetra-fluoride or thorium oxide. The results obtained with thorium of these two types agreed within the experimental error. PROCEDURE AND MATERIALS Procedure—The method used to determine the solubility was to saturate a sample of thorium with hydrogen and analyze a portion of the saturated sample. This method was chosen rather than a determination of pressure-composition isotherms since it was much less time consuming and could be applied at temperatures at which the equilibrium hydrogen pressure was too low to measure. The

Jan 1, 1960

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.' MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970

By T. L. Fritzlen

EXTRUSION of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact' that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relationship between the temperature of the material being extruded and the pressure required to extrude. According to Schishokin,2 this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. CHARACTERISTICS OF THE EQUIPMENT The capacity of the press determines the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1945

By S. F. Shaw

THE principles involved in lifting oil in wells flowing naturally are identical with those underlying the flowing of wells by means of the air-gas lift, and information of a dependable nature obtained in the study of the air-lift can be applied to wells with natural flow. A well flowing naturally is one in which the lifting is done by means of the gas-lift, for which the gas is supplied entirely by the formation from which the oil is derived. In air-gas lift operations, there is insufficient gas supplied by the formation to lift the oil to the surface in an efficient manner, therefore additional gas for this purpose must be furnished from an outside source. There may, at times, be conditions obtaining in natural flowing wells different from those in wells flowed by gas-lift, but these differences do not at all conflict with the main principles of gas-lift work. One such condition is met with in wells in which the gas supplied by the formation is in considerable excess of that required to lift the oil to surface; this excess may be so great as to reduce the quantity of oil that can be lifted through the particular diameter of casing or tubing that has been lowered into the well. This same condition can be brought about, however, by supplying a large excess of gas from an outside source to an artificial gas-lift well, and a study of the effects obtained from injecting a large excess into the well can be applied directly to handling wells flowing naturally which have a large excess of gas supplied by the underground reservoir.

Jan 1, 1929

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By P. H. Brace, N. A. Ziegler

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time. THE FURNACE Our furnace may be described as "a high-frequency induction furnace of the bell-jar type." It is similar in a general way to that described by Cain and Peterson' though we have introduced certain refinements of

Jan 1, 1928

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150'C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.' The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.' The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00' were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-'. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By J. E. Burke, C. W. Mason

IN attempting to study precipitation from a tetragonal lattice using solid solutions of bismuth in tin, it was found that although a Widnmanstatten pattern is observed 1 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process MICROSCOPICAL STUDIES Alloys were made from Chempur tin (Standard samples 42b and 42c, National Bureau of Standards), and bismuth (Kahlbaum C P ) by melting neighed quantities together under palm oil, stirring well, and casting in a heated graphite mold The polishing and etching techniques employed largely govern the visibility of the structural changes The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through BehrManning 3/o abrasive papers, lubricated by a solution of paraffin in kerosene A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution, repeated etching and polishing served to remove disturbed metal For high-power examination better preparation was necessary It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a Heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use A better procedure was as follows The metal lap was warmed slightly, and a 4-in circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C was poured over it, allowed to stand for 1 to 2 min and then washed off It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample The cloth was then charged with a paste of the relevigated alumina in water Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deteriorates after about 24 hr This is not serious, because a new lap can be prepared in about 5 min, and only small pieces of cloth are used Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer For the final etching, the most satisfactory reagent was that of Taffs,7 the formula for which is FeC13 6H20, 2 grams, HC1, 5 c c , H2O, 30 c c , C2H5OH (95 per cent), 60 c c This etchant reveals differences in com-

Jan 1, 1941

By Gilbert P. Moore

Production in the Argentine in 1930 amounted to 1,415,099.7 metric tons, which converted into barrels of 42 gal., using the factor of 6.29, amounts to 8,909,773 bbl. This is a decrease of 481,613 bbl. from the 1929 production, which was 9,391,386 bbl. The production for 1930 was divided among three fields, as shown in Table 1. Table 2 covers Table 1.—Argentine Oil Production, 1930, by Fields Barrels Comodoro Rivadauia District Government........................................... 4,547,670 Railways Co........................................... 1,314,358 Astra-Eastern......................................... 1,016,024 Anglo-Persian......................................... 365,021 Solano Co............................................. 24,613 Dutch Shell........................................... 6,963 7,274,649 Neuquen District Government........................................... 569,245 Standard Oil-Argentina................................. 659,551 Astra-Eastern......................................... 8,234 Challaco Co. (Sol)...................................... 121,598 1,358,628 Salta District Government........................................... 90,576 Standard Oil-Argentina.................................. 185,920 276,496 8,909,773

Jan 1, 1931

By Ralph M. Hunter

UNTIL recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged break-down did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to by-pass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdiness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, therefore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 2946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1948

With the inauguration of Petroleum Technology this year, and approval by the Board to add an Assistant Secretary to the New York staff to serve the Petroleum and Coal Divisions, the Petroleum Division looks forward to greater opportunities and responsibilities. An improved medium of publication offers further incentive to engineers and investigators in the oil industry to make contributions. The authorization by the Board of Directors of a new Assistant Secretary is an appreciation of the splendid contributions made to the industry by the open forum of the Petroleum Division. It is also a recognition of the possibilities of greater service to the membership along the lines established ten to fifteen years ago by DeGolyer, Fohs, Ambrose and Lovejoy, to mention a few leaders. It isexpected that the new officer will spend a substantial part of his time in the field, visiting the student sections, the respective Divisions, helping in the arrangement of papers and Section meetings and intensifying interest in the Institute. The Petroleum Division will hold three meetings this year. The Fall Meetings will be held on Oct. 6 and 7 in San Antonio and on Oct. 20 and 21 in Los Angeles. The programs for these meetings will deal chiefly with engineering research and production engineering problems. Papers on production statistics and general economics of the industry are reserved for the Annual Meeting in New York. The annual production symposium and statistics are accepted as standard for the industry. With continuously deeper penetration into the earth in search for and exploitation of petroleum, it is necessary to have a better understanding of reservoir conditions and to place more phases of the operation under engineering control. Among the subjects relating to reservoir conditions tha thave been proposed for the fall meeting programs are phase equilibria at high pressures, interfacial tension between oil and water, the flow of oil and water through sands, the chemistry of films and underground temperatures. Investigations relating to control of operations include methods of continuously logging while drilling both visually and electrically, methods of studying drilling samples, properties of drilling fluids, improved cementing practices for isolating thin sands under high-temperature conditions and gas conservation, particularly production from high-pressure reservoirs. Additional suggestions of general themes or individual subjects will be welcomed, since it is desirable to build a backlog of material for Petroleum Technology. 9

Jan 1, 1938

By Byron E. Eldred

Generally speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. yet these other arts show quite plainly that a thermal-value basis alone is not sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other, arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a

Jan 1, 1911

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe' using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"' pure silwer and Ag-0.5 at. pct ~n;' and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l' Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele'~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,'~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,' Gallaher,' and Gallagher and Wash-burn.' Ives and Ruff' found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

The microstructural stability of 59 carbon and low alloy steels after 34,000 hr exposure at 900' and 1050°F, including the weld heat-affected zone, is discussed. The tensile and creep rupture properties of the parent metal of many of the steels before and after 10,000 hr exposure are presented. SEAMLESS pipe has been used for many years at elevated temperatures. When seamless first began to be used, operating temperatures and pressures were relatively low and the steel produced adequately met the existing requirements. The need for knowledge of creep properties and graphitiza-tion was nonexistent. Today the requirements for tubular products have changed considerably. Operating temperatures and pressures are increasing continually and corrosion, particularly at high temperatures, presents a problem. Carbon steels have, under these conditions, certain economic advantages particularly in oil refinery use. However, the use of low alloy steels in the generation of steam power has increased appreciably due to the influence of molybdenum on creep strength and the control of graphitization with chromium. The behavior of carbon and certain low alloy steels after long periods of exposure at 900° and 1050°F (480° and 565°C) has been investigated. The steels were examined before and after 10,000 to 34,000 hr exposure. Results obtained with material exposed at 1200°F (650°C) are not presented due to the severe oxidation and resulting decarburiza-tion after long periods of exposure. The graphitization characteristics of carbon and low alloy steels are of fundamental concern to the users of these materials. This is particularly true where welded joints are employed. In order to evaluate properly the behavior of steels at elevated temperatures, it is desirable to employ not only long periods of exposure under controlled conditions, but to use material with known properties and steelmaking practices. The purpose of this investigation has been to study the microstructure of the weld and the tensile and creep rupture properties of the parent metal after long periods of exposure at elevated temperatures. In the report'.' of a previous investigation data were presented on the microstructure, impact strength, hardness, and oxidation characteristics after 10,000 hr exposure at elevated temperatures. When this investigation was planned, methods for controlling the graphitization characteristics of steel were not established and, therefore, a number of special alloy steels were included in the study. During the exposure of these steels, the influence of aluminum in accelerating the rate of graphitization and the inhibiting power of chromium were established by various investigators. Also, the vanadium-bearing steels, because of their outstanding creep properties, received attention. As a result of these developments, considerable progress has been made in the field of high temperature tubular products, and the necessity for special alloys to prevent graph-itization has been restricted largely to the use of chromium. Material Chemical analysis, deoxidation treatment, and austenitic grain size of the 59 steels discussed in this paper are shown in Table I. The steels were forged to 1x1 in. bars with the exception of steels 12B, 12DX, 12DY, 12DZ, 70, 70A, 72 to 78, 82, and 83 which were machined from heavy wall pipe. All bars were surface ground before exposure. Heat treatment before exposure is shown in Table 11. The majority of the steels included were melted in either a basic open hearth or basic electric furnace; how-

Jan 1, 1955

By William J. McCaughey, Richard L. Barrett

FOR sixty years-in fact, ever since the inception of the basic steelmaking process -basic slags have been the subject of study by chemists, metallurgists and petrographers, with the purpose of providing a better understanding of the reactions between the slag and the metal during the refining process. The result of this work and of the researches of mineralogists and physical chemists into the chemistry of oxide systems is a considerable body of literature dealing not only with slags themselves but with equilibrium relationships in systems synthesized from pure components. Since any actual slag is a multicomponent system more complex than any yet worked out in the laboratory, a complete solution to the problem is still far away. The writers have recently published a paper1 which they believe sheds light on the role of the slag in the elimination of phosphorus and it is the purpose of the present paper to discuss the metallurgical applications of that work. Since the pioneer investigations on the constitution of basic slags carried on by Stead and Risdale, Carnot and Richards, Hilgenstock and others in the 1880's, a considerable body of literature on this subject has appeared. Many of the more important of these papers were summarized in the previous paper,' therefore they will not be reviewed here. PETROGRAPHIC STUDY The present writers have had occasion, over a period of years, to examine petrographically a great number of basic steel- making slags having a very wide range of chemical compositions and made under various conditions of operating practice. Although certain of these slags exhibit some unusual features, it is a remarkable fact that the great majority of mature slags show certain typical characteristics, which persist throughout the wide range of chemical compositions. The typical mature slag usually appears under the microscope to consist of two phases. The phase of primary crystallization is light colored and doubly refracting. If separated mechanically and subjected to chemical analysis, it is found to consist essentially of SiO2, CaO, and P2O5. Sometimes, although not usually, two such silicate-phosphate phases are found. The other conspicuous phase is dark in color and optically isotropic, and occurs as the interstitial material between the grains of the light colored phase. This dark colored interstitial phase when analyzed is found to consist essentially of FeO,Fe2O3, MnO, and MgO. In some slags high in iron oxide, particularly those from low-carbon heats, dicalcium ferrite is found. This phase is dark reddish brown in color and anisotropic.

Jan 1, 1944

By M. F. COOLBAUGH

WHEN I was asked to speak on the subject of leaching, I did not realize that a complete summary of recent progress in leaching had been given by Stuart Croasdale. I shall try to give some other phases of the subject that were not touched by Mr. Croasdale. Not all metallurgists are in harmony as to their methods of treating metals. If they were it would probably mean lack of progress. They can be divided into two classes-the pyrometallurgists, using fire means, and the hydrometallurgists, or those using leaching methods. Conflict is always good for progress; we have it in politics, and in religion there are fundamentalists, and those who are not fundamentalists. As representing pyrometallurgy, may I hope not to be classed among the fundamentalists. The leaching of ores is not new. The leaching of ores for the recovery of metals, however, is quite new. The older leaching was simply to recover the salts. Agricola, back in 1555, I think it was, outlined a great many methods of leaching for the recovery of salts. They called them solid juices at that time. There was no real competition, however, between leaching meth-

Jan 1, 1926

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946