Search Documents

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

By J. R. Linney

THE Eastern Magnetite Industry produced approximately 7,850,000 long tons of crude ore in 1945 from which was obtained approximately 3,650,000 long tons of shipping product or a ratio of 2.10 to 1. Lack of skilled or experienced miners was the greatest handicap. Veterans returning to work improved the underground labor shortage in some localities but as a whole the labor shortage was keenly felt throughout the industry. One cannot now predict what may be accomplished in 1946 but barring major steel strikes a worthwhile improvement can be expected. At the Richard mine of the Richard Ore Co., the shipping product for the year amounted to approximately 124,650 long tons of concentrate and lump ore. Crude-ore production was 160,600 long tons. The average analysis for lump ore was 63 per cent iron and for concentrates 66.05 per cent. The Warren Foundry and Pipe Corp. at their Mt. Hope mine produced 73,000 long tons of lump ore averaging 59.5 per cent and 57,000 long tons of concentrate averaging 67 per cent. The total mine hoist was approximately 209,000 long tons. Operations were commenced through the new Leonard shaft on Jan. 18; the Brown shaft through which operations had been conducted since 1912 caved beyond repair on Sept. 26. No one was injured but pumping facilities were somewhat disrupted. In order to reach designed capacity a total of 400 men will be required with 300 underground. Due to shortage of labor all operations in 1945 were concentrated on the 1700 level. As fast as men can be hired and trained development of the 2100 and 2500 levels will commence. Mt. Hope has a consider-

Jan 1, 1946

By Bruce A. Kennedy

If it had not been for the persistent cold wind, the sun blazing out of a cloudless blue sky would have made it one of those warm, idyllic early spring days which attract the socalled "snowbirds" to Northern Mexico for a vacation at this time of year. At a drill site perched on top of a rather exposed mountain we were installing a number of borehole extensometers in diamond drill holes. A Threading Problem For the uninitiated in geotechnical instrumentation, a borehole extensometer is a series of anchors installed at various depths in a borehole, each anchor being independently connected by a tensioned wire to a measuring device set in the collar of the hole. Any movement of the rock at depth is detected by the anchors and transmitted by the wires to the measuring device. Flexible plastic tubing is used as a spacer between the anchors and the measuring wires are run up the inside of the tube. At this particular site we were installing an instrument string nearly 1000 ft in length. Threading wire only 0.041 in. in diam through 1000 ft of plastic pipe is almost as difficult as getting the proverbial camel through the eye of a needle.

Jan 1, 1971

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962

By Jack Parker, Gonzalo Barrientos

The most realistic mine pillar design is based on observations and measurements in situ. Low-cost reliable instrumentation has made this approach possible. At the White Pine mine, with its thousands of pillars of all shapes and sizes under all kinds of loading conditions, practical pillar design criteria have been developed. The pressure arch theory is explained and work in two test panels o f the mine is described. The pressure arch mechanism, which relies on lateral stress for support, can be applied to puzzling roof and pillar conditions in other mines.

Jan 1, 1975

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, 'the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, 'the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

The Carol concentrator of the Iron Ore Company of Canada was completed in 1962 and through expansions .has become one of the largest iron ore beneficiation plants in the world with a new feed capacity of 147,000 It (149,350 mt) per day. The Carol ore contains specular hematite and magnetite having a bulk density of 166 lb/cu ft (2660 kg/m3) It is crushed to 7 in. (178 mm) for feeding to autogenous mills for subsequent concentration by Humphrey’s s spirals. Mine ore is loaded into 150 It (152 mt) trucks by 10 cu yd (7.65 m3) shovels and then, at a transfer station, is loaded into side-dump rail cars of 100 It (101.6 mt) capacity. Each train is composed of twenty cars and operates completely automatically as it hauls the ore to the primary crushing station, dumps its loads, and returns to the loading station, a 11.5 mile (18.5 km) round trip. The primary crushing station is composed of two 60 in. by 89 in. gyratories installed in 1962 and 1972. Neither crusher has a grizzly ahead of it. Rail cars are dumped into 300 It (305 mt) pockets which contain splitters for spider protection. What few oversize boulders which do not go through the crushers are drilled and blasted. Liners in the dump pocket and the crushed ore pokcet under the crusher are manganese steel. Both crushers are direct driven by 700 hp (5 15 kw) motors, and the hardness of the ore causes them to pull almost their full power. Crushed ore drops into a 160 It (163 mt) pocket equipped with radioactive level control units for low-intermediate, and high level indications. The low level unit stops and starts the apron feeder, the intermediate unit controls the feeder speed, and a high-level reading stops the car dumping. Apron feeders are 72 in. (1. 82 m) wide and are variable speed from 12 to 52 fpm (3. 7 to 15. 8 mpm). They discharge to 60 in. (1.52 m) wide takeaway belts. Crushing capacity, nominal and maximum for each crusher, is 4, 000 ltph (4. 064 mtph) and 4,600 ltph (4,674 mtph). The crusher eccentric is removed by a conventional cart which travels on removable rails. Mainshaft removal and maintenance is done by 65 and 75/10 ton cranes. Mainshaft replacement requires eight hours, a usual time, but concave replacement requires only sixteen hours, a result of a fine maintenance organization. Mantle relining is done at grade next to a repair track. Zinc is used for backing both mantles and concaves. Both the electrical rooms and the dust collectors are located below grade,

Jan 1, 1978

By W. O. Philbrook, K. Natesan

The oxidation kinetics of spherical pellets of zinc sulfide made from Santander concentrates were studied using a thermogravimetric technique. The experiments covered a temperature range-. of 740" to 102O°C, 0-N mixtures varying from 20 to LOO pct O2, and pellet diameters between 0.4 and 1.6 cm. Mathematical models were formulated to Predict the reaction rate on the assumption that a single transport or interface reaction step was rate -controlling. Analysis of the data indicated that the process of oxidation was predominantly controlled by transport through the zinc oxide reaction-Product layer. ROASTING processes, which are reactions between solids and gases, are very important because they are employed in the production of a number of basic metals. These processes are highly complicated, and one needs to consider the transport phenomena of heat and mass between the solids and gases in addition to the kinetics of various chemical reactions involved. Because of such complications there is a lack of knowledge concerning the rate-limiting factors, which may strongly depend on temperature, particle size, gas composition, and solid structure. The oxidation of zinc sulfide, which is of commercial importance in zinc production, falls into this class of reactions. The major goal of this work was to elucidate the roles played by different process variables, such as reaction temperature, gas composition, pellet size, and pellet porosity, on the kinetics of oxidation of single pellets of zinc sulfide. Roasting of zinc sulfide single particles has been a subject of both experimental and theoretical investigations.&apos;-&apos; The reaction is exothermic and may be considered to be irreversible. Such a reaction has been found to proceed in a topochemical manner. In other words, as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,1-9 that the particle retains its original dimensions and the process requires transport of gaseous oxygen across the porous product layer for continued reaction. The reaction may be represented by ZnS(s) + 3/2 O2(g) = ZnO(s) + SO2(g) [1] The solid product considered here is only zinc oxide, since the diffraction patterns of zinc sulfide pellets oxidized partially at &apos;798" and 960°C showed K. NATESAN, Junior Member AIME, formerly St. Joseph Lead Fellow, Department of Metallurgy and Materials Science, Carnegie-Mellon University, Pittsburgh, Pa., is now at Argonne National Laboratory, Argonne, Ill. W. 0. PHILBROOK, Member AIME, is Professor of Metallurgy and Materials Science, Carnegie-Mellon University. This paper is based on a them submitted by K. NATESAN in partial fulfillment of the requirements for the Ph.D. degree in Metallurgy and Materials Science at Carnegie-Mellon University. Manuscript submitted December 2, 1968. EMD lines corresponding to original zinc sulfide and the newly formed zinc oxide. OXIDATION MODEL The generalized model for gaseous oxidation of zinc sulfide is illustrated in Fig. 1. This depicts a partially oxidized sphere of zinc sulfide in a gas stream surrounded by a laminar film of gas. The spherical sample of zinc sulfide of unchanging external radius r0 is suspended in a flowing gas stream of total pressure PT and composition specified by the partial pressures of the individual components. Partial pressures of the gaseous species in the bulk gas phase, at the exterior surface of the pellet, at the ZnS/ZnO interface, and at equilibrium for Reaction [I] are identified by the superscripts b, o, i, and eq, respectively. The overall reaction involves the following ~te~s:&apos;~&apos;~&apos; Step 1. Transfer of reactant gas (oxygen) from the bulk gas stream across the gas boundary layer to the exterior surface of the pellet and the reverse transfer of the product gas (sulfur dioxide). Step 2. Diffusion and bulk flow of oxygen from the pellet surface through the product shell (ZnO) onto the ZnS/ZnO interface and the reverse transfer of sulfur dioxide. Step 3. Chemical reaction at the interface, which results in consumption of oxygen gas and generation of sulfur dioxide gas and heat; at the same time the _________ PARTICLE SURFACE / x^^^^n^X / MOVING INTERFACE core-----/ sJSNxy " /T^T^02 \ V\V$\ ^NWX/ "*/— GAS BOUNDARY x. \\ZnO SHELLV/ / \^ . / &apos; ^ BULK GAS --------N_______ _____,------p£ w \ P« / (f> \ / a \ <i) / <----------------- _(o) ^^--------------(b) °- pso, pso2 ro ri 0 ri ro RADIAL POSITION Fig. 1—Generalized model for oxidation of a sphere of zinc sulfide.

Jan 1, 1970

By L. M. Litz

Study results are presented in which gaseous oxygen was dissolved in the leach liquor at concentrations of the order of 300 ppm. This oxygen-containing solution was injected into portions of a field being operated on a commercial basis with hydrogen peroxide as the oxidant. Comparative results indicate that uranium concentrations and production rates were essentially equivalent with these two oxidants.

Jan 1, 1983

By S. W. Zehr, G. S. Murty, W. A. Backofen

AN observation by Squires, Weiner, and phillipsl has stimulated interest in a mechanism of deformation at high temperature (above -0.5 of the absolute melting point) that is not usually thought to be involved in the creep of metals. They found precipitate-free or "denuded" zones along grain boundaries normal to the stress axis in tensile specimens of a hydrided Mg-1/2 wt pct Zr alloy after slow straining at 450° and 500°C. Their suggestion that the zones were a result of directional diffusion of magnesium atoms was supported with calculations from Harris and Jones2 which also tended to identify the process as Nabarro-Herring (N-H) creep3,4—a process that is characterized by Newtonian viscosity, with stress (o) directly proportional to strain rate (C), and one that proceeds by lattice diffusion. Material transport by diffusion along grain boundaries is an alternative basis for Newtonian viscosity, as demonstrated by Coble,5 and is favored over N-H creep for fine grain size and lower temperature.6 In either case, the strain rate sensitivity of flow stress, defined as m = d log o/d log E (which commonly appears in the empirical a = KEW), is unity. The experiments to be described here gave metallo-graphic indications of diffusional creep which were no less clear than those just cited, but the associated m (as measured by the method of Ref. 7) was much more like that of a Bingham material. For true Bingham behavior, (a — ao) E, where oo is an initial yield stress. Therefore, even if flow after yielding should occur by diffusional transport, m must increase from 0 as < is raised to reach unity only in the limit as One result is that the resistance to tensile necking conferred by Newtonian viscosity is lost, which would become increasingly apparent through the formation of more sharply defined necks as 6 is lowered. That trend appeared in these experiments. Most of the work was done on an extremely finegrained alloy of magnesium with -6 wt pct Zn and ½ wt pct Zr (Mg ZK60); the initial mean-intercept grain diameter, L, was 0.55 µ. Shown in Fig. l(a) is a germanium-shadowed carbon replica of the surface of a specimen that was coated with silicone oil,* heated to 270°C under a helium atmosphere, and then stretched locally -200 pct at an initial E = 3.3 x 10-5 sec-1. Under

Jan 1, 1969

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

By J. E. Hilliard

Isobaric sections of the eutectoid region of the iron-carbon phase diagram have been exgerimentally determined at 35, 50, and 65 kb. The phase boundaries were located by metallographic analysis of specimens quenched after equilibriatwn at known temperatures and pressures. With increasing pres -sure a pronounced decrease in the solubility of FesC in austenite was observed together with a depression of the eutectoid temperature. These two effects resulted in a shift of the eutectoid composition toward a lower carbon content; at 65 kb the eutectoid was at less than 0.2 wt pct C. These results are in qualitative agreement with thermodynamic calculations. It has also been shown by calculations that Fe3C in contact with saturated austenite will be stable with respect to both graphite and diamond formation at all pressures above -3.5 kb. 1 HE investigation described in this article was part of a more general study of the effect of high pressure on transformations in Fe-C alloys. Thermodynamic calculations and exploratory runs made in 1959 at the start of the program indicated an appreciable change with pressure in the phase equilibria of Fe-C alloys. However, the calculations were not considered reliable enought to provide the quantitative information required for the interpretation of the effect of pressure on the kinetics of transformations. An experimental investigation was therefore made to determine a series of isobaric sections of the eutectoid region of the phase diagram at pressures up to 65 kb. EXPERIMENTAL PROCEDURE Materials. Seven alloys with analyzed carbon contents of 0.10, 0.20, 0.38, 0.60, 0.77, 0.93, and 1.20 wt pct C were prepared from Ferrovac" iron and high-purity graphite induction melted in magnesia crucibles under argon. The ingots were hot worked and swaged down to 0.19-in.-diam rod which was then centerless ground to a final diameter of 0.125 in. Samples for chemical and spectrographic analyses were taken from each end of the rods. The prin- cipal impurities were found to be Ni, Al, Co, and Si which were present in amounts up to 0.03, 0.02, 0.01, and 0.01 wt pct, respectively. Specimens were prepared by slicing the ground rods into pills 0.06-in. thick which were silver plated to reduce decarburization during the equilibration. Silver was chosen for this purpose because of its very low solubility for carbon and its mutual immisicibility with iron. High-Pressure Apparatus. The high-pressure runs were carried out in the "Belt" apparatus.&apos; As shown in Fig. 1, this consisted of a cylindrical cell compressed between two Carboloy punches loaded by a uniaxle press. Radial support to the cell was given by the "belt" which was a Carboloy die heavily prestressed by a series of steel binding rings. Laminated gaskets of lava and metal separated the punches from the inner surface of the "belt". A cross-section of the high-pressure cell is shown in Fig. 2. Two specimen pills were located inside a resistance heater of 0.20-in.-diam Nichrome tubing. The ends of the tube were sealed with alumina and lava pills tamped in place after the

Jan 1, 1963

By J. R. Long, T. R. Graham

THIS report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau&apos;s War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. PRELIMINARY WORK In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, 0 to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening, effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

Prof. Henry M Howe, New York: It is extremely probable that this efflorescence of silica is due to the liquation either of silicon or of a silicide, and the subsequent oxidation of the silicon to silica. As Mr. Fackenthal says, it is very hard to see why silicon should liquate from an iron containing so little silicon, and it seems more probable that some silicide of some volatile element has liquated, and has dissociated on reaching the air, and that the volatile element has volatilized, leaving the silicon to oxidize to silica. The volatile elements present which might thus liquate in combination with the silicon are sulphur, zinc, and lead. It is hard to see why sulphide of silicon should have liquated from an iron containing so little of either sulphur or silicon. At first, one naturally thinks that either the zinc or the lead present in this furnace might have liquated as silicide. It is true that they are both volatile at the temperature within the furnace, but then the vapor-tension* of each of them within

Jan 1, 1901

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,&apos; a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By Fred H. Klaer

Water supplies dependent upon induced infiltration can be developed by vertical wells, by infiltration galleries, or by horizontal water collectors. Each method is described and the advantages of water obtained by induced infiltration with respect to cost, chemical quality, and temperature are shown by specific water supplies.

Jan 6, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952