Search Documents

By Frank Firmstone

(Ottawa Meeting, October, 1889. Substituted for the briefer note on the same subject. pre sented at the meeting and subsequently distributed in preliminary pamphlet edition.) Prof. H. Hoefer's theory of blasting was published in the Oesterr. Zeitschrift, xxviii., 1880, and xxix., 1881; and Part 111. in Nos. 15, 16 and 17, xxx., 1882, and subsequent numbers of that

Jan 1, 1890

By R. L. Fleischer

IN 1925 a criterion for localized deformation in a single crystal was derived by Taylor and Elam.' They noted that for a single active slip plane the slip plane area is constant, but the direction of the stress with respect to the slip direction changes during deformation so that, when the increase in stress due to this rotation is large enough relative to the work hardening, instability occurs. (By instability is meant continued slip on the active slip plane.) The instability criterion may be written t>dt/d?/m tan2? [1] where t and ? are resolved shear stress and strain, m the Schmid factor for resolving shear stress, and ? is the angle between the slip direction and the axis of tension. The formula points out that regardless of the atomic mechanism involved, for large flow stresses and low work hardening rates, slip on a single plane—once started—should continue. The case of alloying provides a direct possibility of adjusting the parameters in Eq. [I]: As an alloying element is added to a pure metal, the flow stress is raised and the work hardening in easy glide may be either decreased2 or unaltered.3 Since flow stresses in easy glide may rise to the kg/mm2 range for alloy crystals while easy glide slopes may be less than % kg/mm2, 2 it is possible for the inequality to be satisfied. Indeed Garstone and Honeycombe3 report that slip becomes coarser with increasing stress in the easy glide range, where the flow stress would be increasing and the slope would be essentially constant. Another case where high flow stresses and low hardening rates accompany coarse slip is that of quench hardening.4 Maddin and Cottrell report that quenched aluminum crystals display slip markings resembling those of a brass. A similar effect has been observed after irradiation.'

Jan 1, 1960

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By A. S. Richardson

THE design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many mines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation may also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps a majority of the shafts used in ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and cross-cuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact it may not be very far wrong to say most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may be varied for economic advantage.

Jan 2, 1926

By Thomas V. Falkie

These are exciting times for the coal mining community. Although the industry is in the middle of a healthy boom, there are strong forces tending to counteract or at least temper the rate of growth. There are many pushing and pulling factors of interest to mining people, and a few salient ones will be mentioned here. Primarily because of a tremendous demand for energy, a demand that can't be met by other fuels, the coal industry is in boomsville. Another contributing factor to this situation is the increased overseas demand for metallurgical coal. These demands are being counteracted by a lack of people, the lead-time required to develop new capacity and wildcat strikes, among other things.

Jan 1, 1971

By F. I. Grace, L. E. Murr

The mechanical responses and residual defect structures in 70/30 brass and type 304 stainless steel following explosive shock loading and cold reduction by rolling have been studied. A distinct relationship was observed to exist between the residual mechanical properties and micro structures observed by transmission electron microscopy. Shock-loaded brass deformed primarily by the formation of coplanar arrays of dislocations and stacking faults at lower pressures, and twin-faults (deformation twins and €-martensite bundles) at higher pressures (> 200 kbar). The micro -structures of cold-rolled brass were characterized by dense dislocation fields elongated in the rolling direction. Stainless steel was observed to deform by the formation of dense arrays of stacking faults at lower shock pressures and twin-faults at high shock pressures (>200 kbar). Lightly cold-rolled stainless steel deformed similar to low Pressure shock-loaded stainless steel, but transformed to a' martensite in heavily cold-rolled stainless steel. Discontinuous yielding was observed for the heavily cold-rolled stainless steel, and stress reluxution in the weyield region for cold-rolled and shock -loaded stainless steel was interpreted as an indication of the ability of twin-faults and stacking faults to act as effective barriers to dislocation motion. A simple model for the formation of the planar defects and a' martetnsite is presented based on the propagating of Shochley partial and half-partial dislocations. A considerable effort has been expended over the past decade in an attempt to elucidate the response of metallic-crystalline solids to the passage of a high velocity shock wave (e.g., smith,' Dieter,2 and zukas3). While it has been possible to obtain relevant information pertaining to the residual defect structures and mechanical properties, there have been few rigorous attempts to draw a direct comparison between these structures and properties. In addition, numerous investigators have recently observed the occurrence of deformation twinning in shock deformed fcc metals (e.g., Nolder and Thomas,4 and Johari and Thomas5), but little attempt has been made to elucidate the mechanisms of formation of these defects. Comparative data for metals deformed by shock-loading and the same metals deformed by more conventional modes of deformation such as cold-reduction by rolling is also generally lacking. The present investigation therefore has the following objectives: 1) to examine the mechanical properties of some explosively shock loaded and cold-rolled fcc metals of low stacking-fault energy as a function of their residual substructures; 2) to present a simple model for the formation twin-faults and related defect structures in the low stack-ing-fault energy materials of interest (70/30 brass, ySFg= 14 ergs per sq cm; and 304 stainless steel, ySF = 21 ergs per sq cm); 3) to make some deductions with regard to the residual characteristics of dislocation and planar defect substructures in cold rolled and shock loaded 70/30 brass and type 304 stainless steel. In particular, it was desirable to characterize the residual hardening effects of particular deformation substructures. I) EXPERIMENTAL PROCEDURE Sheet samples of 70/30 brass (0.005 and 0.15 in. thick; annealed at 659°C for 2 hr) and type 304 stainless steel (0.007 in. thick; annealed 0.25 hr at 1060°C) of nominal compositions shown in Table I were cold-rolled in one direction only to produce reductions in thickness of 15, 30, 45, 60, and 75 pct in the brass; and 5, 15, 25, 35, and 45 pct in the stainless steel. Identical sheet samples in the annealed (unrolled) state were subjected to plane compressive shock waves to various peak pressures ranging from 0 to 400 kbar in the brass and 0 to 425 kbar in the stainless steel; and with a constant peak pressure duration of approximately 2 microseconds. A detailed description of the shock loading technique has been given previously.6 Tensile specimens 1.0 in. in length and 0.125 in. in width were cut from the cold-rolled sheets (tensile axis parallel to the rolling direction), and the shock-loaded sheet specimens. Stress (load)-strain (elongation) measurements on the tensile specimens were made on a Tinius-Olsen load-compensating tensile tester using a strain rate of 2.7 x 10-3 sec-1. Tensile tests were repeated at least twice, giving essentially the same results. Stress relaxation measurements in the preyield region were also made using an initial strain rate of 5.4 x 10-4 sec-1. In addition to tensile and stress relaxation measurements, Vickers microhardness measurements were made on all samples. A total of 100 microhard-ness readings were obtained for each specimen following a light electropolish to ensure uniform surface conditions for all tests. The hardness averages ob-

Jan 1, 1970

By H. B. Bell, P. C. Lidster

A study has been made of the use of ThO2-Y2O3 solid electrolytes to determine activity of chromium in Fe-Cr and Ni-Cr alloys in the temperature range 1300° to 1700°K. This method has been shown to give results which agree with the best vapor pressure measurements. SEVERAL investigations1"5 have been made of chromium activities in Fe-Cr alloys. Most of these have been made by vapor pressure measurements using knudsen cell techniques while one has been made using gas equilibration with H2/H2O gas mixtures. In the present investigation electromotive force measurements have been made on this system using a thoria yttria solid electrolyte. This system was -chosen to establish the technique of measurement at low oxygen potentials, before extending it to Fe-Ni-Cr alloys. The cell used was Pt Cr • Cr2O3 ilThO2 • Y2O3 llalloy • Cr2O3 IPt Since the oxygen pressure of the chromium-chromic oxide mixture lay in the range 10"19 to 1027 atm in the temperature range investigated, thoria yttria electrolytes were used. It was soon found during the investigation that considerable care was required to prepare satisfactory electrolytes and a study was made to find the best method of preparing pellets of TI1O2-Y2O3 solid solution of as near theoretical density as possible. Various compositions in the range 2 to 15 mole pct Y2O3 were studied but the experimental measurements were made with electrolytes containing 4 to 5 pct Y2O3. The method of preparation finally adopted was to use thorium oxalate and yttria as raw materials. The thorium oxalate was decomposed at 900°C for 6 hr to give a reactive powder. This powder was then mixed with the appropriate amount of yttria and ground in an agate mortar for about 4 hr. The powder was moistened with absolute alcohol as a lubricant and pressed in a metal die at a pressure of 7 tons per sq in. The pellets were then heated at 1100°C for 24 hr followed by 24 hr at 1250°C. After this firing cycle the material was reground and repelleted and again fired at 1100° and 1250°C followed by heating for 7 days at 1600°C. It was found in later experiments that a further firing of 4 hr at 2000°C improved the density further and gave pellets of only 2 pct porosity. After firing, the pellets were polished on emery paper and finally with the 2 µ diamond paste. The polishing was followed by a final firing of 24 hr at 1500°C. Investigation showed that this final treatment minimized reaction between the electrolytes and chromium oxide. It was believed that this was because of a lowering of the surface energy of the electrolyte surface. Two types of investigation were carried out to check that the pellets were satisfactory oxygen ion elec-

Jan 1, 1970

Jan 1, 1880

By Charles Will Wright

The present struggle for economic and industrial supremacy by the Communist world is against the United States, its main target, and the other Free World nations. The basis of industrial power is minerals, so the Communist nations are building up mineral production within their borders, often regardless of costs, and are acquiring quantities of mineral products from Free World countries for future use. They are contracting for additional supplies and advancing funds for the development of these quantities. A number of the less developed mineral producing countries of the Free World are being infiltrated by Communists and Communistic influence. This situation is well known, but as yet little has been done to oppose these activities or to awaken the public to their seriousness. The Communist countries are still far behind the Free World Nations in production of many essential minerals. But, shortages are being made up from Free World nations in exchange for petroleum, manganese ore, chromite and other products. Restrictions on shipments of strategic materials to Communist countries have not been maintained.

Jan 1, 1964

By Gunnar Almgren

Hole deviation has great consequences on mining economy, especially for long hole drilling technique. First of all the bore hole datas are concerned but also such factors as development, loss of ore and waste rock dilution are influenced. Hole deviation for sublevel open stoping is illustrated with examples from some mines. The deviations are indicated as mean values but also as standard deviation values, owing to their statistical distribution. The economic influence of the hole deviation is especially studied for steep, small lowgrade orebodies, mined with big hole blasting. Hole deviation can thus influence costs up to US$ 3-4 per ton for operating, development, losses of ore and rock waste dilution. This cost is of the same magnitude as the total operating costs for many sublevel stoping mines. The economic savings in accurate drilling are therefore substantial and are worth all attention.

Jan 1, 1981

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" ' also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder')"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder's results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13' and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*' " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.'" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.''' The experiments which will be described in this paper pertain to: (a) the effect of a crystal's shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By J. J. Lander, L. H. Germer

Molybdenum and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved onlv limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150°C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1949

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By B. A. Wilcox, A. H. Clauer

The tensile and creep deformation characteristics of fiber reinforced composites have been studied, primarily at room temperature. The matrix was an alloy of Mg-14 wt pct Li-1 wt pct Al (LA141A alloy) and the reinforcing fiber consisted of continuous wires of a high strength precipitation hardening stainless steel (AFC-77 alloy). The ultimate tensile strength and strength-to-density ratio of composites were much improved over that of the mmix, both at room ternperatwe and up to 200°C. Creep studies at room temperature revealed logarithmic weep behavior for wires and composites and steady state creep for the nonreinforced matrix. It was concluded that creep of the fibers controlled composite creep. The instantaneous logarithmic weep rate of the composite, 6, was related to the average tensile stress on the fibers, where n = 3.4. Mg-Li alloys are the lightest structural metals commercially available, e.g., the alloy LA141A (Mg-14 wt pct Li-1 wt pct Al) is 27 pct less dense than beryllium Although Mg-Li alloys have moderate tensile strengths at normal strain rates and ambient temperature, their creep strength is relatively poor, even at room temperature. Reinforcement by fibers offers a means of increasing the tensile strength as well as overcoming the limitations of low creep strength. With a proper choice of reinforcing filament, composites could be designed with higher strength-to-density and modulus-to-density ratios than the matrix alloy. This communication reports a study on the tensile and creep characteristics of alloy LA141A reinforced with continuous wires of a high-strength precipitation hardening stainless steel (AFC-77 alloy). The matrix has a bcc structure, with possible precipitates of AlLi and MgLi2A1,3 and is ductile at room temperature Stainless steel wire was chosen as the -reinforcing filament since previous work at Battelle4 showed that a good bond between wire and matrix could be produced in this system. For all volume fractions of reinforcing wire, the theoretical composite strength-to-density ratio is greater than that of the matrix and the modulus-to-density ratio is somewhat lower than that of the matrix. EXPERIMENTAL PROCEDURES The 0.004-in. diam AFC-77 wire was obtained from two suppliers: National-Standard Co.* and Crucible 0.13 Si, 0.18 V, 0.011 P, 0.012 S, balance Fe. In the as-received condition, wires from both sources had room-temperature ultimate tensile strengths of 585,000 to 590,000 psi with approximately 2 pct total elongation and 40 pct reduction in area. Composite preparation was accomplished by the vacuum infiltration technique. This involved placing the continuous wires in a mild steel tube (1/8-in. ID), capping one end of the tube with a sheet of the matrix alloy, and evacuating the other end of the tube. When the capped end was placed in a crucible of the molten matrix alloy and held for 31/2 min at 70O°C, the liquid metal was drawn up the tube approximately 7 to 8 in. A cross-sectional view of a typical composite is shown in Fig. 1. This preparation technique promoted excellent bonding between the matrix and wires, and porosity was rarely observed. Test specimens for both creep and tension studies were prepared by machining off the steel tube. Tensile tests on the wires and composite specimens were made in an Instron using a cross-head speed of 0.01 in. per min. The composite specimens had no reduced section and were held in self-tightening grooved serrated grips. Most of the specimens broke in the effective 1-in. gage section. Even though several tests fractured in the grip section, their ultimate strengths were essentially the same as those of specimens which fractured in the gage section. Creep specimens of the composite were gripped in a similar manner, and

Jan 1, 1970

By A. M. Tweedy, Felix A. Vogel

Since the publication of Prof. J. W. Richards's paper on The Schumacher Briquetting Process,' this process has been in operation on a practical scale in two plants in the United States, and a few notes on the results obtained may be of interest. An experimental plant, consisting of a toggle press and a hydraulic press, was installed at Johnstown, Pa., together with the necessary bins and other equipment, and an attempt was made to briquette a mixture of Mahoning fines and blast-furnace flue dust, in a ratio of 7 parts of ore to 3 parts of dust. The results were unsatisfactory, in that the briquettes made were not hard enough to stand the severe handling to which they were subjected in the various transferences necessary between the press and the furnace. The trouble was due to several causes: First, the mechanical arrangement of the plant, which did not lend itself to a proper hardening and loading of the briquettes into the cars. Second, the irrrgular composition of the flue dust, as to both its lime and its fine coke contents. Third, the variability of the moisture content of the ore, and its viscosity when wet. Fourth, the ratio of fine ore to flue dust; that is, it was attempted to bind in too large a quantity of fine ore for the small amount of flue dust used. The first trouble could be overcome, and has been improved upon in the plant as it stands to-day. The second trouble was important, because of the small amount of dust used as a binder, and might have been easily removed by mixing the flue dust of the different furnaces, which, however, was never done. The third difficulty was more serious, but could have been partly solved, had it been possible to meet this along with the fourth difficulty, by decreasing the percentage of ore in the briquettes. It was proposed to do this, but it seems that the problem at the works in question is, primarily, to prepare Mahoning fines for reduction in the blast furnace, and only secondarily to use up the flue dust, and a solution along this line did not seem to be interesting.

Jan 1, 1914

By P. S. Rudman

Crystal-structure occurrences in binary phase diagrams of fifth- and sixth-period elements, zirconium through palladium and hafniun through platinum, are surveyed with the conclusion that average .group number GN is the dominant correlative. This is interpreted in terms of curves of enthalpy differences between competitiue structures that are continuous func -tions of GN. It is further reasoned that the absolute formation energies may also be continuous functions of GN and if so can be simply obtained from the regatives of the heats of sublimation of the elements. It is shown that from such a heat of formation-GN plot the heats of mixing of alloy systems can be quantitatively predicted. For example, for sixth-period alloys very large exothermic heats of mixing are predicted for systems that span GN = 6 (i.e., Hf-Pt, Ta-Os, ...). Thermodynamic data with which to test these predictions do not appear to be available. If in the latter transition (A subgroup) elements we eliminate from consideration the fourth period where magnetic terms contribute to crystal-structure stability, as shown in Table I, there is a very regular sequence of structures. Using the group number (GN) assignments of Table I, which differ from the usual assignments of 8 to the elements listed as 8 through 10, it is perhaps trivial to say that the phase occurrence is a unique function of GN. However, the interesting aspect of alloys from among these elements is that the alloy structures also appear to correlate with GN. The GN for an alloy is given as GN = SixiGNi, where xi and GNi = atomic fraction and GN of component i, respectively. It is difficult to credit anyone in particular with having discovered this correlation, so many people have implicitly or explicitly employed it in the last 10 years. However, Bloom and Grant' in their correlation of s-phase occurrence with total number of d + s electrons were certainly one of the first to appreciate the correlation and Hume -Rothery2 appears to be responsible for the use of average GN as defined above. Only in the last few years have the phase diagrams of enough alloy systems been determined for this correlation to be surveyed with any degree of completeness. We shall here, in an abbreviated format, summarize the available phase-diagram literature and discuss some consequences of the GN correlation. BINARY DIAGRAM SURVEY In Figs. 1 to 3 the phase occurrences are summarized. In Fig. 4 the occurrence limits for the more common structures are summarized. That the GN of an alloy falls within the occurrence limits of a particular structure is a necessary but not a sufficient condition for the appearance of that structure. The preceding figures certainly illustrate that GN is a dominant correlative for structures of these elements. Many of the diagrams have complications, with ordering and other phase changes occurring in intermediate phases, that cannot be clearly accommodated in such a schematic survey and have hence been left out. Such omissions cannot, however, negate the GN correlations discussed here. Relative atomic size is also an important crystal-structure determinant and since atomic size varies quite regularly with GN for these elements it is possible that the apparent GN correlation is basically a size correlation. In Fig. 5 relative size occurrence limits are given for intermediate phases and extended terminal solutions. The relative volume, ?v/(v) - 2(vA - vB)/(vA + uB), has been taken as the measure

Jan 1, 1968

By Stuart H. Ingram

The term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. Background The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they fiequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. Increased Demand In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to Overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, Or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new Or or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. Recent Development Descriptions of ancient work contain references to the use of spalls of tuffs Or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1948

By Stuart H. Ingram

The term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. Background The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they fiequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. Increased Demand In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to Overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, Or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new Or or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. Recent Development Descriptions of ancient work contain references to the use of spalls of tuffs Or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1948

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By R. N. Hoffman

A new technique for determining capillary pressure curves has been developed and tested. The technique differs from previously reported centrifuge techniques in that the centrifuge is slowly accelerated from zero to the maximum desired speed rather than being held constant at particular, progressively higher speeds. An important advantage of this technique over other methods of determining capillary pressure curves is the short time required to obtain the desired amount of data over the chosen pressure range. For example, to obtain 30 data points between 1.2 and 104 psig with a 1.55-in. long, 3/4-in. diameter core using a brine-air system, 6.6 hours were required with this technique. An equally important development of this paper is an analytic method for the conversion of the data from the centrifuge experiment to capillary pressure curve data. Previously there has been only an approximate conversion available. Although the capillary pressure curves determined by this technique appear to be as accurate as those determined by other techniques, the accuracy could be improved if certain variables, not treated in this experiment, were investigated. Among these are the dynamic distortion of the centrifuge equipment and imperfect initial saturation of the cores. INTRODUCTION Pirson 1 defines capillary pressure in a porous medium as "the differential pressure that exists between two fluid phases at their interfaces when they are distributed under static equilibrium within a porous material". Capillary pressure in rocks is known to be a function of fluid saturation, among other things, and a capillary pressure curve is defined for the purposes of this paper as a plot of the capillary pressure-wetting phase saturation relationship for a particular rock sample. Several methods are used for determining capillary pressure curves for small rock cores. Prominent among these are the semi-permeable barrier, mercury injection, and, to a lesser extent, centrifuge methods. The semi-permeable barrier method is currently the most popular. It features simplicity in both execution and the mathematical conversion of the experimental data into a capillary pressure curve. The main disadvantages of the semi-permeable barrier method are the time required — as long as two months — to obtain several points for the curve, and a fairly low maximum pressure before breakthrough of the non-wetting phase into the barrier occurs, for example, about 32 psig for a brine-air system. It is for these reasons that other methods such as the centrifuge method have been introduced. High accelerations and the absence of a barrier result in quicker attainment of saturation equilibrium at a given pressure. However, the centrifuge method involves much more expensive equipment and more difficult procedures and calculations than does the barrier method. The purpose of this investigation has been to improve the equipment and procedures of the centrifuge method and to develop an analytic method for the conversion of the experimental data into a capillary pressure curve. Hassler and Brunner did the original work in the determination of capillary pressure using a centrifuge. In their work the centrifuge speed was increased in a step-wise manner, each speed being held constant until saturation equilibrium was reached in each core. Saturation equilibrium was indicated when the volume of liquid collected in the graduated pipette of the core holder remained constant. According to Hassler and Brunner, equilibrium was reached in "a few minutes to one-half hour or more". In the centrifuge method, as opposed to the barrier method, the fluid saturation of the core is not a constant throughout the length of the core, but varies with the radius of centrifugation. Also, the capillary pressure cannot be read directly but must be calculated from a knowledge of the centrifuge speed and other parameters. For these calculations, Hassler and Brunner derived the following equations: