Search Documents

By E. W. McAllister

THE decision of the California Oil Umpire's1 office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in Kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in their respective wells. Shortly thereafter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clarks and C. B. Kimberlin‡ in a reports dated March 1933. PRODUCTIVITY INDEX In the majority of individual well problems involving the use of subsurface pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettleman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time for various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As. the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

Jan 1, 1890

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

1944 WALTER HULL ALDRIDGE New York, N Y 1946 PETER M ANDERSON Johannesburg, South Africa 1946 CHARLES CAMSELL Ottawa, Ont, Canada 1946 CHARLES AUGUSTUS CARLOW Fife, Scotland 1946 CECIL H DESCH London, England 1946 WILLIAM FRASER London, England 1917 HERBERT HOOVER New York, N Y 1941 DANIEL COWAN JACKLING San Francisco, Calif 1939 HENRY KRUMB New York, N Y 1942 ESSINGTON LEWIS - Melbourne, Vic , Australia 1921 C MCDERMID London, England 1944 WALTER C MENDENHALL Washington, D C 1942 PAUL DYER MERICA New York, N Y 1913 EZEQUIEL ORDONEZ Mexico City, Mexico 1938 A M PORTEVIN Paris, France 1937 GEORGE S RICE Washington, D C 1934 T A RICKARD Victoria, B C, Canada 1946 JOHN R SUMAN Houston, Texas 1946 WONG WEN-HAO Chungking, China

Jan 1, 1952

1944. Walter Hull Aldridge New York, N. Y. 1946. Peter M Anderson Johannesburg, South Africa 1946. Charles Camsell Ottawa, Ont. Canada 1946. Charles Augustus Carlow Fife, Scotland 1949. Erie Victor Daveler New York, N. Y 1946. Cecil H. Desch London, England 1946. William Fraser London, England 1917. Herbert Hoover New York, N. Y. 1941. Daniel Cowan Jackling San Francisco, Calif. 1939. Henry Krumb New York, N. Y. 1942. Essington Lewis Melbourne, Vic., Australia 1921. C. McDermid London, England 1944. Walter C. Mendenhall Washington, D. C. 1942. Paul Dyer Merica New York, N. Y. 1938. A. M. Portevin Paris, France 1934. T. A. Rickard Victoria, B.C., Canada 1946. John R. Suman Houston, Texas 1946. Wen-Hao Wong Chungking, China

Jan 1, 1952

1944 WALTER HULL ALDRIDGE New York, N Y 1946 PETER M ANDERSON Johannesburg, South Africa 1946 CHARLES CAMSELL Ottawa, Ont, Canada 1946 CHARLES AUGUSTUS CARLOW Fife, Scotland 1949 ERLE V DAVELER New York, N. Y 1951 EVERETTE LEE DEGOLYER Dallas, Texas 1946 CECIL H DESCH London, England 1946 WILLIAM FRASER London, England 1917 HERBERT HOOVER New York, N. Y 1941 DANIEL COWAN JACKLING San Francisco, Calif. 1950 ZAY JEFFRIES Pittsfield, Mass 1939 HENRY KRUMB New York, N Y 1942 ESSINGTON LEWIS Melbourne, Vic, Australia 1944 WALTER C. MENDENHALL Washington, D. C 1942 PAUL DYER MERICA New York, N Y 1938 A M PORTEVIN Paris, France 1934 T A RICKARD Victoria, B C, Canada 1946 JOHN R SUMAN Houston, Texas 1946 WONG WEN-HAO Chungking, China

Jan 1, 1952

By Charles E. Mann, Douglas J. Lootens, Rufino B. Bomasang

INTRODUCTION The economy of the Philippines, like that of many other developing nations, has been severely strained by the rapid escalation of imported crude oil prices over the past decade. In an effort to reduce its dependence on imported crude, significantly increased emphasis, both in the public and private sectors, is being placed on the rapid development of Philippine coal resources. This paper is designed to present an overview of the Philippine coal industry, its historical development, present status, and future potential. COAL RESOURCES AND RESERVES In 1977, a British consulting firm collated all available data on Philippine coal resources and estimated the total coals potential at about 0.9 to 1.4 billion metric tons (mt). In 1981, using more recent data the Philippine Bureau of Energy Development (BED) estimated the potential at 1.7 billion mt. The BED estimated the proven coal reserves at 257 million mt. These coal resources are scattered throughout the major islands comprising the Philippine archipelago. However, about 52 percent of the currently proven reserves are located in the tiny island of Semirara between the islands of Mindoro and Panay. About 25 percent is located in the Cagayan Valley in northeastern Luzon while 13 percent is located in Mindanao. The remaining 10 percent is scattered in the islands of Cebu, Samar, Mindoro, Negros, Polillo, Batan, and Catanduanes. The bulk of Philippine coal is sub-bituminous in rank. Some bituminous coal with coking properties has been reported in Malangas, Zamboanga del Sur in western Mindanao, and in Catanduanes, but the exact tonnages have not been accurately established. It is believed, however, to be at most 5 million tons. A little semi-anthracite coal exists in Malangas with the remaining unmined reserves estimated at a little more than one million tons. Table 1 shows the quality ranges of Philippine coal deposits.. Figure 1 shows the distribution of known Philippine coal resources PHILIPPINE COAL PRODUCTION In 1981, total coal production was 330,720 mt. Though modest by world standards, this was the highest production figure in Philippine coal mining history. This came from 25 mines, mainly small scale underground mines of capacities varying from 10 to 100 tons per day (tpd). The actual production capability was about 800,000 mt in 1981, but the producers had to scale down production to the level of local demand. Even then, some 50,000 tons of coal remained unused by year-end. The 1981 production came from the following areas: Cebu 224,751 mt (68%) Zamboanga del Sur 57,095 mt (17%) Semirara 13,222 mt (4%) Polillo 17,132 mt (5%) Cebu has always been the main source of Philippine coal production. Coal mining has been carried out in Cebu for the last 50 years, although it has been characterized by a very crude mining technology. Due to the limited size of coal deposits and complicated geology, however, Cebu's share of the total national production is expected to go down to only 10 percent by 1985. Except for Semirara's open-pit production, the balance of Philippine coal production comes from underground mines. These underground mines generally use room-and-pillar methods, except for those at Zamboanga del Sur and Polillo which use modified longwall methods patterned after those used in Taiwan. Due to the much higher mining recovery, most underground mines are now planning on switching to longwall. At Semirara, an open pit mine is now being developed for a one million ton per year capacity by 1984, and will then be the largest Philippine coal mine. While present earthmoving work is done with bulldozers, loaders, and trucks, the main coal extraction equipment will be bucket wheel excavators imported from Austria. PRESENT COAL UTILIZATION Existing coal production is sold mainly to coal- fired cement plants and power plants. The balance is sold to a sugar central, a coconut oil mill, a food processing plant, and two plants producing carbide and ferro-silicon alloys.

Jan 1, 1982

By L. A. White

IN this paper it is proposed to follow the developments in the design of the lead blast furnace at Port Pirie from the time The Broken Hill Associated Smelters Pty. assumed control in 1915 to the present time, with special reference to the development of the system using two superimposed rows of tuyeres as is now in operation. Lead smelting operations first commenced in 1889, when the British Broken Hill Pty. Ltd. started its first furnace. This was followed by installing two more furnaces during the same year and another the following year. In 1892, Broken Hill Proprietary Co. Ltd. acquired the smelting works and combined operations with those at Broken Hill, New South Wales; by 1897, the whole of the smelting operations had been transferred to Port Pirie and thirteen blast furnaces were built to treat the Broken Hill ore production. In 1915, The Broken Hill Associated Smelters Pty. Ltd. took over from the Broken Hill Proprietary and have carried out operations since that time. From its inception, the present company started on a long range program of reconstruction, in which the development of the lead blast furnace has played a prominent part. A definite trend in plant development has been towards the simplification of plant control by a reduction in the number of operating units. The great advantages of technical control which resulted from the very simplified flowsheet established in the continuous refining process stimulated the desire to extend the principle to the smelting operation. Thus in the sequence of furnaces described here, it will be noted that the trend has been towards larger and, of course, fewer units. With each such development it is significant that the operating conditions and metallurgical results have shown steady improvement. Standard Furnace In 1920 there were seven furnaces operating, five of a type subsequently called the standard furnace and two of the original thirteen smaller furnaces, the latter type being used for the treatment of drosses, etc. produced from the refinery section, while the standard type carried out the main, lead-smelting operations. The standard furnace (figs. 1 and 2) had the dimensions given in table I.

Jan 1, 1951

"The richest hill on earth" had its start as a placer gold camp in 1864. The gold was quickly worked out but then silver was discovered in the copper ores in Butte Hill. After ten years as a silver camp, rich copper ore was found in 1881 and the future of Butte was assured. In the early 1960's, the Anaconda Company began the shift from underground mining at Butte to open pit mining of the enormous, low-grade copper deposit surrounding the old high-grade veins which had been worked for over eighty years. Their first primary crusher was a 66 in. by 84 in. (168 m by 2. 13 m) jaw crusher. The pit was expanded at such a rate, however, that its location became endangered. Additionally, the new Clyde Weed concentrator had been built at Butte; and in 1969 construction of a new gyratory installation was started. The primary crusher at the Clyde Weed concentrator is one of the most unusual primary crushers ever put into operation. At times, the ore from the Berkeley pit contains large amounts of timber, pipe, rails, and so forth left in the ore body from the old underground mining operations; and the crusher installation had to be designed so this tramp material could be readily removed ahead of the crusher. Ore is delivered by 100- and 150-ton trucks to two side-by-side dump pockets, each with a capacity of 400 tons. Originally, a hydraulic grapple was installed on the dividing wall between the dump pockets; but it was found that oversize boulders large enough to block the discharge opening at the bottom of each hopper were rapidly covered with other material, and the grapple was unable to reach and remove the large boulders causing the blockage. In addition, the grapple was located in a quite vulnerable position; and it sustained damage from being struck by rock dumped from the trucks. Oversize boulders are now blasted. Underneath each pocket is a vibrating grizzly feeder with the grizzly bars set at 4 in. (102 mm). These feeder-grizzlies are 84 in. (2. 13 m) wide and 32 .ft (9. 75 m) long, with grizzly sections 16 ft (4. 88 m) long. Approximately 75% of the ore passes through the grizzlies and grizzly oversize then drops onto two parallel 6 ft (1. 83 m) wide picking belts. The belts are 3 in. (76 mm) thick and rest on idlers supported by air- filled rubber shock absorbers. At the side of each picking belt is a hydraulic grapple which is used to remove timbers too large to be removed by hand. At times, four men are used to remove timber and tramp iron. Timbers are dropped onto a transverse belt conveyor which discharges into a truck stationed outside the primary crusher building,

Jan 1, 1978

By Guillermo Hileman

Probably the outstanding feature of the oil industry in the Argentine, during the past year, was the increase in production from the Comodoro Rivadavia field. This increase was accounted for by the discovery of a deeper producing horizon in the old coastal field (zone A). The oil, derived from the deeper sands, served not only to balance the natural decline of the upper sands and increase the yield from the area, but also provided a product of comparatively superior quality. The finding of this ney- production in the old field had a special economic significance because of the pumps, tanks and pipe lines already installed to take care of it. The deep horizon is looked upon as a life

Jan 1, 1937

By M. J. Shulman

With the spiraling cost of exploration, all stages of exploration must be optimized. Search theory calculates the optimal distribution of effort by maximizing the probability of discovery under the constraint that the total exploration budget is not exceeded. It may help formulate strategies during the reconnaissance phase of exploration. An incremental optimization analogous to the exact solution of the search problem is introduced. In conjunction with the optimization, various stopping criteria can be defined. The stopping criteria terminate exploration in an area during a particular stage. It does not refer to abandoning exploration. The following stopping criteria were considered: the exploration effort in an area should not exceed a maximum value; the posterior target location probabilities should not be less than a percentage of the initial probabilities; the change in the posterior target location probabilities should not be less than a given value; and the change in the marginal rate of return should not be less than a given value. The incremental optimization and the stopping criteria are used to allocate reconnaissance mapping and sampling effort for phosphorite in the Sinai Peninsula, Egypt.

Jan 1, 1986

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By Robert L. Kidd

ONE time or another placer mining attracts the attention of a large number of people, because of the possible low initial investment, low operating cost, and quick returns. Much has been said about sampling and operating placer deposits but many are still inclined to jump at a property without giving much, if any, consideration to proper sampling. This statement does not apply to experienced mining engineers but I am hoping that readers will tear out this article and pass it along where it will do the most good and thus help to preserve the reputation of legitimate mining. It would appear that some people have an ability to sink test pits in high-grade gravel that is positively uncanny. One pit showing high-grade values proves to some property owners and promoters that the entire property will do the same. This is

Jan 1, 1937

By Harry H. Angst, Reuel A. Cochrane

THE successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. ROCK FORMATIONS At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in-the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1941

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

By J. Marvin Weller, M. King Hubbert

Preliminary investigations were undertaken with a Megger Ground Tester in 1931 by Hubbert to determine whether the faults in Hardin County, Illinois, could be located by earth-resistivity surveys. The results of these investigations, which were in part presented before this Institute in 1932,1 were sufficiently promising to warrant a more extensive field program in the same general area the following summer. During the second season an apparatus of the Gish-Rooney type was employed because of its greater sensitivity and to avoid the troublesome correction for resistance of potential electrodes necessitated by the use of a Megger instrument. The discussion of earth-resistivity traverses which constitute the main part of this paper is based entirely upon the results of the second season's work. All of the traverses were made with a constant electrode spacing of a equal to 100 ft., and the four-electrode technique was employed. Successive stations in these traverses were spaced at intervals of 100 ft. and the line of electrodes was carried parallel to the line of traverse. The graphs of resistivity profiles presented here (Figs. 1 to 3) are plotted with resistivities in ohm-centimeters as ordinates and with distance divided into stations at 100-ft. intervals as abscissas. After the traverses were run by Hubbert the results were computed, the profiles plotted, and tentative interpretations were made by him. These curves and interpretations were then taken into the field by Wellcr, who made a careful geological examination along the lines of traverse for the purpose of checking and supplementing Hubbert's interpretations. Weller then constructed a geologic cross-section extending along the line of each traverse. The accompanying diagrams graphically illustrate the correlation that can be made between earth resistivity and geology in this area.

Jan 1, 1934

By Charles Legrand

IN many iron, coal and copper mines where large tonnages are known before starting operation and proper provisions can be made, the problems of electric traction by trolley locomotives are not very different from those of surface plants. In such installations the gauge of the track, the radius of curves, and the clearances, both vertical and horizontal, can be made to suit the conditions of the traffic. It is more difficult to install electric traction in mines which were started with hand tramming and where no consideration was given to the possibility of mechanical traction being used. The writer having had some experience in the installation of electric traction in copper mines, the following remarks apply more particularly to these mines. With the gauge of track usually 18 or 20 in., the weight limit of locomotives obtainable from manufacturers in this country varies from 3 . to 6 tons. The full-load speed varies from 42 to 6 miles per hour. These locomotives, being made to run on very small radius curves, have a short wheel base and a long overhang from axle to coupling, which necessitates a coupling with a good deal of lateral motion to avoid derailing the cars on sharp curves, especially if couplings are of the standard railroad automatic type. Although, 3-ton locomotives will run on 12- or 16-.1b. rails, it has been found more satisfactory to use 25-lb. rails, as the track keeps in much better shape, it is easier to maintain the bonding in good order, and fewer derailments from dirt on the track occur with the larger rails. Where 6-ton locomotives are used the 25-1b. rails are satisfactory, but 40-lb: rails have proved cheaper where the traffic is heavy and the ground is soft, as the track maintenance is considerably lower with the heavy rails. The locomotives will run on 15-ft. radius curves, but on through runs it is advisable not to go below 40-ft. radius.

Jan 2, 1914

By H. Foster Bain

THERE has never been a great civilized nation which did not have a mining industry; civilization cannot flourish without metal mining. Without tools we can have none of the 'industries that are the foundation of civilization and without metal mining we cannot produce the material of which tools are made. Therefore, if we have no metal mining we have no metals, no tools, no civilization. An example to illustrate this may be drawn from a recent article in the Saturday Evening Post which described the run-down condition of modern Athens. Athens is nothing but a busted mining camp! In its palmy days the Greeks so applied the leasing system to the silver mines of Laurium that the royalties, paid the expenses of government and instead of a tax bill the inhabitants received a pay check. The Persians came over to capture these mines but the Greek navy was built to defend them. When the silver mines played out, Greek civilization declined.. Our mining must continue if our civilization is to continue.

Jan 1, 1921