Search Documents

By R. A. Falconer, H. L. Lovell

With increasing requirements for fine coal cleaning and the many advantages of the cyclone operating on a coal-water slurry, a series of studies designed to achieve an enhanced understanding of the cyclone parameters has been pursued. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydro-cyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. This study of the hydrocyclone is a continuation of a series of investigations, conducted in the Dept. of Mineral preparation at The Pennsylvania State University, which are directed toward the removal of ash and sulfur constituents from fine bituminous coal by size-density separations in cyclones, and toward a fuller understanding of the complex mechanisms involved in such separations. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydrocyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. Of special interest was the response to cone angle variation, since it is the high included cone angle that generally distinguishes the hydrocyclone as a gravity separator rather than a classifier. DESCRIPTION OF THE HYDROCYCLONE Fig. 1 is a dimensional drawing of the hydrocyclone used in the investigation. The unit was designed and fabricated by Heyl and Patterson, Inc., for experimental use. The dimensional parameters considered were: 1) Three cone sections having included angles of 45, 60, and 95,degrees, 2) Three 3 1/8 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in., 3) Three 4 1/16 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in. 4) Two apex sections having diameters of 2 and 2 1/4 in. The feed inlet orifice had a fixed diameter of 3 in. The hydrocyclone test installation was made at The Pennsylvania State University pilot plant at Barnes-boro, Pa., which operated at 50 tph. During the period that the hydrocyclone was tested, research was in progress at the Barnesboro site to reprocess refuse material from a near-by coal preparation plant in

Jan 1, 1968

By Charles E. Wait

IN order to secure cupels uniform in size, density, etc., I have arranged a machine which has proved quite satisfactory, and is so simple and inexpensive as to be within the reach of nearly everyone. It has been in operation here about four years, and with it all cupels used in the assay department of the School of Mines have been made. As shown in the accompanying figure, it consists of a common letter-press, the movable platen of which has been removed. In place of the plate, there is attached to the screw a plunger, which turns with the screw, moving up and down, and making the depression in the cupel. The ring holding the bone-ash is held in place directly underneath the plunger by a wooden guide fastened to the base of the press. There is also fastened to the top of the guide for the ring, at a distance above the base of the press equal to the height of the cupel-ring, a piece of mood about § inch thick, under which the ring will just slide into place, and through which there is cut a circular hole exactly fitting the plunger, guiding it in its downward movement always in the same vertical line; this last guide not only directs the plunger, but also prevents the lifting of the ring by the plunger, upon the raising of the latter.

Jan 1, 1886

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks' have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author's responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By R. E. Goodman, M. A. Mahtab

The, state of stress around a vertical wellbore in rock following nonlinear stress-strain laws is examined by means of finite element analysis. The wellbore, is considered an axisymmetrier body with axisymmetric loading. The initial vertcal and borizontal stresses are "locked" in the rock elements around the wellbore and a new state of stress is generated by the displacements which occur around the borehole. A point-uise variation of the elastic moduli is made on the basis of the new stress state and the triaxial data. The initial stresses tire now reintroduced along with tile changed moduli and original boundary constraints. This procedure is repeatrd until convergent stresses are reached. The effect of nonlinearity on streases is examined for a 6,000-ft wellbore in a scbistose gnezss and Berea sandstone using results of laborratory triaxial compression tests. The results sbou that the effect is restrited to one well radius from the bottom periphery of the bole. Beyond a distance of one-quarter radius, the elfect of nonlinearity on stresscs IS almost always less than percent for the cases conszdered, The consideration of a static pressure inside the well does not magnify the effect of monlinearity on borehole stresscs. INTRODUCTION The terms " wellbore" and "borehole" here designate cylindrical openings in the ground with vertical axis and a circular cross-section. A knowledge of the stress redistribution that occurs on excavating a wellbore is important in understanding (1) the behavior of the lined or unlined hole, (2) hydraulic fracture response, and (3) the effect of stress redistribution on drillability; also it is important in predicting initial stresses in the virgin ground, and in analyzing the response of measuring instruments placed in the borehole. Our knowledge of the state of stress around a wellbore has been restricted to homogeneous, isotropic, elastic material and derives chiefly from the analysis by Miles and Toppingl and the photoelastic work of Galle and Wilhoit2 and Word and Wilhoit.3 In this investigation the state of stress is examined for a nonlinear elastic material by means of finite element analysis. Many rocks possess stress-strain curves that depart notably from straight lines in their initial or final portions. While the literature contains abundant stress-strain data from triaxial tests (axisymmetric loading) on cylindrical rock specimens, there is little information on rock deformability under nonaxisymmetric loading conditions such as occur at each point around the bottom of a wellbore. Although there is some knowledge of the effect of intermediate principal stress on rock strength, there is virtually nothing known about its effect on rock deformability; therefore, we have assumed here that the effect of intermediate principal stress can be ignored. A schistose gneiss4 and Berea sandstone5 were selected as representative rocks for this analysis. The traditional graphs of deviator stress (ol -o3) vs axial strain were reworked to give the tangent modulus as a function of the deviator stress for varying values of the minor principal stress. The result is a nesting family of skewed, bell-shaped curves for tile gneiss (Fig. 1A) and the sandstone (Fig. 2A). A similar replotting of the lateral strain data defines the variation of Poisson's ratio (v) with the deviator stress and confining pressure. These curves, shown in Fig. 1B for the gneiss and in Fig. 2B for the sandstone, are not so well ordered as the tangent modulus curves. However, all of these display an increase of v with deviator stress application, but the rate of increase diminishes with confinement. The ET and v curves for the two rock types are tabulated in Tables 1A and 1A for use in a digital computer so that material properties corresponding to a given state of stress can be assigned by interpolation. STATEMENT OF THE PROBLEM Given a state of stress in the ground prior to drilling a hole (initial stresses), we assume that

Jan 1, 1969

By A. S. Malicsi, I. Iwasaki

The removal of hydrophobic coatings of flotation collectors from iron ores becomes of interest when a duplex flotation process is considered for upgrading, when a pelletizing process is considered for a concentrate floated with a fatty acid or a soap collector, or when a disposal of froth products from cationic silica flotation is of environmental concern. Ozone can oxidize organic compounds rapidly, thereby removing the hydrophobic coatings of flotation collectors. Ozone is widely used for treating and purifying drinking water, waste water treatment, and for chemicals processing (Murphy and Orr, 1975; Rice et al., 1980). Its uses in metallurgical operations, however, are very sparse (Allegrini et al., 1970; Chernobrov and Rozinoyer, 1975; Ishii et al., 1970; Iwasaki and Malicsi, 1985; Matsubara et al., 1978). Yet, its high reactivity and the absence of potentially hazardous byproducts become of interest in destroying flotation reagents adsorbed on mineral surfaces or remaining in mill water for recycle or for discharge. Duplex Flotation A duplex flotation process, as applied to oxidized iron ores, would involve a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process has been used in the Florida phosphate fields. Fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates. A combination of reagents, such as lime and quebracho, lime and alkali phosphate, or sulfuric acid and oxalic acid, has therefore been proposed. In a previous article (Iwasaki et al., 1967) , the use of activated carbon was found to be effective in removing fatty acid coatings both in the duplex flotation and the pelletizing processes. The use of ozone offers another approach to the removal of fatty acid coatings from iron oxide surfaces. To investigate the possible application of the duplex flotation process, a specularite ore from Michigan analyzing 36.5% iron was used. A 600-g (1.3-1b) sample was ground in a laboratory rod mill together with 250 g/t (0.5 lb per st) of sodium silicate to -150 µm (-100 mesh). This was transferred to a Fagergren laboratory flotation cell, and deslimed four times at 20 µm (quartz equivalent). The deslimed pulp was transferred to a laboratory conditioner, diluted to 40% solids, and conditioned with 250 g/t (0.5 lb per st) of soda ash and 250 g/t (0.5 lb per st) of oleic acid. The conditioned pulp was then transferred back to the Fagergren cell, floated until barren of froth, and the rougher froth product was returned to the cell and cleaned. The results are presented in Table 1. The cleaner concentrate at this point analyzed 45.3% Fe. The cleaner concentrate coated with fatty acid was transferred to a 2-L (0.53-gal) beaker. While the pulp was agitated with a glass T-stirrer, ozone was bubbled into the agitated pulp for 15 minutes at a rate of 10 mg/min (0.00035 oz per min) ozone (250 g/t or 0.5 lb per st 03 feed). It was observed that the pulp ceased to froth after about 10 minutes. The amine flotation of siliceous gangue from the ozonated pulp was carried out first by conditioning with a dextrin, a commonly used starch depressant for iron oxides. This was followed by flotation with a stage addition of an ether amine at increments of 100 g/t (0.2 lb per st). Three stages were required to float the siliceous gangue to near completion. The three froth products were combined and cleaned twice. When the cationic flotation Rougher, Cleaner 1 and Cleaner 2 cell products were combined, an iron concentrate analyzing 64.5% iron was obtained at an overall iron recovery of 72.8%. Pelletizing Fatty acid flotation concentrates have been pelletized successfully in northern Michigan mills. But at other locations, fatty acid coatings on iron flotation concentrates proved so undesirable in agglomeration that other methods of concentration had to be sought. For example, a sinter mix containing iron ore concentrates upgraded by fatty acid flotation resulted in decreased productivity. This occurred because the micropellets of particles with the hydrophobic coating are less tolerant of moisture. Thus, the bed permeability is lost (Beebe, 1965). The agglomeration of concentrates obtained by the fatty acid flotation alone, and the hydrophobic coatings destroyed by ozonation or by the duplex flotation process, is not expected to cause any difficulty since the surfaces of the concentrates would be hydrophilic. Removal of the fatty acid coating with activated carbon, indicated by the loss of floatability, was shown to restore the decrepitation temperature of wet balls during drying cycle (Iwasaki et al., 1967). Disposal of Cationic Silica Flotation Froths Recent demands of iron blast furnaces place the silica content of the magnetic taconite pellets at about 5%. Conventional process for magnetic taconite involving fine grinding and magnetic separation often produces magnetic concentrates analyzing in excess of 5% silica. This is due to the presence of the middling grains of siliceous gangue and magnetite. Cationic silica flotation of magnetic taconite concentrates (DeVaney, 1949) may be used to reduce the silica content. But the amine coating on siliceous gangue becomes of environmental concern when the flotation tailings are discarded in tailing ponds.

Jan 1, 1986

By C. H. Li, R. J. Stokes, S. H. Bendel, J. A. Sartell, T. L. Johnston

The mechanism of the oxidation of high-purity copper has been studied at temperatures from 500° to 981°C employing gravimetric, high-temperature microscopic and inert marker techniques. An investigation of the adhesion of copper oxides was also made. The oxidation of copper is found to be parabolic at all temperatures. It is concluded that the controlling mechanism is the outward diffusion of CU+ ions through the Cu2O layer, but the mechanism of diffusion is modified by the state of compressive stress in the oxide layer at the oxidation temperature. At temperatures below the transition from elastic to plastic behavior of Cu2O the growth stresses reach a value sufficiently high to cause CuO whiskers to be extruded. The extrusion of whiskers results in the injection of a large number of vacancies into the CuO. The Cu20 layer grows by the advance of the CuzO/CuO interface into vacancy-rich CuO. Since there is an adequate supply of non -thermally created vacancies, the activation energy for oxidation is that required to move the Cu+ ion through the appropriate saddle point to a neighboring vacancy, which has been determined to be 20,000 cal per mole. At temperatures at which the Cu20 can deform plastically the stresses are never high enough to cause whiskers to form. thus vacancies must be supplied by themal activation and as a result the activation energy increases to 40.000 cal per mole. ALTHOUGH extensive studies of the oxidation kinetics of pure copper have been made in the past. the mechanism has received relatively little attention. As a result, certain features of the kinetic data have not been satisfactorily explained' For example, several workers1,2 have reported that the activation energy for oxidation in the range from 500° to 700° C was about 20,000 cal per mole whereas that above

Jan 1, 1960

By V. G. Leak, R. A. Swalin

The dilhsion of silver and trace concentrations of tin in liquid silver has been rrzeasured in the temperature range from about 975° to 1350°C. The difBsion dala. fil lhe following equations: fov self-diffusion of silver The ratio of DSn to DAg is found to be about 1.34. The higher diffusivity of tin is interpreted in terms of the coullombic repulsion which results from the fact that tin dissolved in silver has a valence of +3 relative to silver. THE phenomenon of diffusion has been well-described theoretically for hard-sphere gases and solids and found to be in good agreement with experimental data for certain gases and solids. Liquid-diffusion phenomena have not been well described theoretically and there is generally a lack of good experimental data. In this investigation self-diffusion and solute diffusion in liquid silver were studied. Silver was chosen as a solvent for two main reasons. First, silver is a noble metal and the atoms are considered to have a spherically symmetric charge field; hence the liquid may be considered to be a random array of approximate hard spheres. Mercury, gallium, and other lower-melting metals were eliminated from consideration since it appears possible that in their liquid states there is some residual long-range order and directional bonding. Second, silver behaves as a monovalent solvent and, while cadmium, indium, tin, and antimony all have nearly the same atomic size, they have chemical valences relative to that of silver of +1, +2, + 3, and +4, respectively. Slifkin, Lazarus, and coworkers1-5 investigated the diffusion of these solutes in solid silver and found that their diffusion rates increased with an increase of the excess valence of the solute. In the solid state the diffusion-rate increase was calculated to be due to a change in local modulus of the solvent caused by the excess valence of the solute.1"3 For the present investigation it was planned to determine the effect of valence upon solute diffusion in liquid silver. It was deduced that a coulombic repulsion between solute and solvent might be responsible for larger volume fluctuations in the vicinity of the solute thereby enhancing the diffusion of the solute atoms. Tin was the first solute investigated and was chosen for experimental convenience. If an excess-valence diffusion effect exists in the liquid state, the solute tin with its excess valence of + 3 might show a large enough effect to distinguish it from the self-diffusion of silver in silver. The silver self-diffusion data were obviously required as a base line for comparison. In addition silver self-diffusion was investigated with a view toward examining the data in connection with the Sutherland- Einstein: Coheen-Turnbull,7 and swalin8 theories of diffusion in liquids. I) EXPERIMENTAL TECHNIQUES The diffusion coefficients for tin and silver in liquid silver were determined in separate experiments using the capillary-reservoir method of Anderson and saddingtono but following closely the experimental techniques outlined by Ma and Swa1in. The radioactive alloy bath was prepared by plating either tin-113 or silver-110 m isotope* onto 99.999 *Isotopes obtained from Oak Ridge National Laboratory. pct Ag rods.* The silver and isotope were melted *Silver obtained from Cominco Co. and mixed in a graphite crucible under a purified argon atmosphere, then outgassed for capillary filling. Some of the fused-silica capillaries were filled individually as reported by Ma and Swalin, but most were filled in a different manner. A long piece of capillary tubing was sealed off on one end and held in the system so that the open end was just above the surface of the molten alloy. The system was evacuated, the open end submerged into the alloy, and argon was admitted into the system up to atmospheric pressure. The molten alloy was forced up the capillary several inches where it solidified and was subsequently cut into segments of the proper length for diffusion annealing. The apparatus for diffusion annealing was the same as that used for capillary filling except that a Pt—Pt, 10 pct Rh therinocouple was placed in the solvent bath in order to accurately measure the temperature during the run. A diagram of the dif-

Jan 1, 1964

By J. H. Swisher

The solubility of graphite in CaO-S2O2-Al,O3 slags was measured by equilibrating slag samples with graphite crucibles and CO gas. Carbon contents as high as 2 ut pct were obtained in CaO-saturated, CaO-A1,O3 slags, and 1.3 wt pct in slags of the composition CaO.Si0,. Although the observed conditions for Sic formation were in agreement with those predicted from thermodynamic data, CaC, was found to form at a lower temperature than predicted frotn thermodynamic data. From measurements of the equilibrium carbon content as a function of CO Partial pressure, it was found that carbide ions dissolve in CaO-A12O3 melts with a valence of minus two. The carbon content increased with CaO concentration in Ca0-Al,O3 melts and increased with SiO, content along the CaO'AlO3-CaOSi0 join in the ternary system. When solid CaC2 was added to CaO-A12O3 and CaO-SiO2-A12O3 slags, it was found that one of the oxides in the slag was reduced by the carbide (Al2O3 in the forrner and SiOz in the latter). In electric furnace steelmaking, a double-slag practice is frequently used to meet alloy specifications. Initially a flush slag, which is oxidizing in nature, is used to remove phosphorus and carbon from the steel bath. Later in the refining period, the flush slag is replaced by a highly reducing carbidic slag. When calcium carbide is formed in or added to a finishing slag, the slag is effective as a desulfurizing agent and also permits alloying elements such as chromium, vanadium, and tungsten to be added to the slag in the form of oxides. The oxides are readily reduced by calcium carbide, thereby minimizing the use of expensive ferroalloys. More work has been done on the thermodynamics of silicon carbide in slags than on calcium carbide. Baird and alor' and Kay and alor' determined the free energy of formation of Sic by measuring the partial pressure of CO in equilibrium with solid silica, silicon carbide, and graphite. Using a similar technique, they determined SiOz activities in CaO-SiOz and Ca0-Si0,-A1203 slags. Rein and chipman3 also determined the free energy of formation of Sic using slag-metal equilibrium measurements. A literature survey has uncovered only one experimental study of the behavior of CaC, in slag systems. Shanahan and cooke4 report the results of some preliminary experiments on the solubility and stability of CaC, in a CaO-A1,03 and a Ca0-Si0-A1,03 slag at a temperature of about 1500". The carbon solubility as CaC, in a slag containing 50 pct CaO and 50 pct A1203 was reported to be 0.6 pct. They also review earlier work on the binary CaO-CaC, system. A eutectic exists in this system, but various investigators disagree on the eutectic temperature and composition. eal has given an explanation for carbide furnace erruptions in terms of the thermodynamic properties of CaC,; his analysis is not based on experimental data, but on compiled data for the free energies of formation of CaC, and CO.' , These data for steel-making temperatures are all extrapolated from the results of low-temperature measurements. In the experiments described in this paper, slag samples were equilibrated with graphite crucibles and with mixtures of CO and argon or with CO gas at 1 atm total pressure for measurement of the carbon solubility. Most of the work was done on Ca0-A1203 binary slags, although in some experiments CaO-SiO, and Ca0-Si0,-A1,03 slags were used. EXPERIMENTAL Slag samples of the desired composition for the solubility measurements were obtained by blending pre-fused master slags. The master slags were prepared by fusing mixtures of reagent-grade CaC03 with either A1,03 or Si0, in a graphite crucible. The master slags were crushed, then decarburized in air in a muffle furnace at 1200O C. A schematic diagram of the apparatus is shown in Fig. 1. The source of carbon for the solubility meas-

Jan 1, 1969

By Wallace Thorneycroft

FOREWORD This paper by Mr. Thorneycroft, Past President of the Institution of Mining Engineers (Great Britain), and chairman of its Subsidence Committee, is a valuable contribution to the assemblage of data on ground movement and subsidence from coal mining. It deals with the effects of advancing longwall, a method almost universal in Europe but as vet little used in the United States outside of Northern Illinois and in a few scattered places elsewhere, in thin coal beds, as in the Lexington field, Missouri, Canon City field, Colorado, and the Birmingham field, Alabama. Although by advancing- longwall, a maximum recovery of coal is obtained and it has to be employed where there are weak shale roofs, especially in deep mines, it is a more expensive method of operation unless the mining conditions are favorable, which is unusual in the United States. On the other hand, there is a growing use in this country of what is essentially retreating long wall, with an approximately straight break-line as described by Rayburn.1 With this method, in which the pillars are substantial, it was shown that the ground movement effect is practically identical with that of advancing longwall, hence the value to mining engineers of the precise data given by Mr. Thorneycroft. His study is unusual in several respects; it deals with conditions connected with ,the mining of a coal bed 20 in. thick, about 490 ft. below the surface, over a mined-out area in a 5-ft. bed about 90 ft. below, which had been mined about 12 years earlier. Both mines passed under Plean House, a building of massive cut stone construction built over a century ago, in which Mr: Thorneycroft resided throughout the under-mining period. Slight cracks opened in the walls as the longwall face approached the house in mining the upper seam, and closed after the face passed and subsidence took place. In the northwest wall, the last wall the face passed under, some stone blocks were broken, which was attributed to a strike period when the advance of face came nearly to a standstill. Other than this there was no perceptible permanent damage, as indicated by the photographs taken by the undersigned in 1923 (Figs. 1 and 2). Mr. Thorneycroft used a novel means of studying the successive positions of the corners of the building: he hung plumb bobs from the eaves and traced the paths of the respective plumb bob points on level surfaces. The angles made by the house walls with the plumb bob lines gave measures of the slope of the subsidence wave at the respective points. A slight upward wave was indicated by the surveys ahead of the subsidence, which would appear to be due to a tilting over of the massive sandstone stratum in the roof measures near the surface, the edge of the subsidence area acting as the fulcrum.

Jan 1, 1931

By H. F. Easter

(San Francisco Meeting, September, 1915) THE lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly oil a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been clue partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lead or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted heady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. This matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is clone by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 8, 1915

By C. S. Matthews, P. Hazebroek, H. Rainbow

It ha been suggested that lormation fractures created by well stimulation treatments will adversely affect sweep-out efficrency in injection operations. Fluid-flow model studies involving vertical fractures of various lengths and fluid systems of various mobility ratios have been carried out to study this subject. In addition, limited data have been obtained on one model containing a horizontal fracture. It was found that relatively long and highly conductive fractures (not generally obtained fracturing operations) were required to affect the sweep-out efficiency substantially. In a given case in the field an approximate distinction can be made between the presence of long conductive fractures and shorter or less conductive ones. This is done with pressure build-up analyses along with data on the relationship of fracture length and conductivity to well productivity. This type analysis shows that usually the fractures induced are either short or of limited conductivity and therefore do not damage sweep-out efficiency. INTRODUCTION Improved well productivity and in-jectivity can frequently be exploited in injection operations. Higher total throughput can yield improved economics. On occasion, the achievement of an increased productivity or injectivity in specific wells can bring about a more uniform sweep of the reservoir. Higher rates can be exploited particularly in water floods of "depleted" reservoirs where a rapid "fill-up" is desired and where low pressures contribute to low well productivity. The creation of fractures local to the wellbore is an excellent means for achieving these objectives. Even though fracturing has been employed in some floods with success,1"3 there still seems to be some reluctance to employ this tool for fear of undue damage to the flood pattern and ultimate recovery. We therefore need to examine the influence which fractures of varying length may have on flood performance and then determine the length of fractures which obtain in the field with conventional fracture treatments. A substantial influence of fractures on the recovery obtained at breakthrough of the injected fluid has been presented by Crawford and Collins for equal fluid mobilities for the line-drive pattern.4,5 In addition, the influence which a fracture has on the production performance after breakthrough and on the ultimate recovery warrants consideration in reaching a conclusion concerning the use of induced fractures in flooding operations. This report presents this type of data for the five-spot injection pattern for several fluid mobilities. In arriving at some conclusion concerning the fracture lengths obtained in field operations we must examine the performance characteristic most affected by the fracture. This is the change in the flow system as reflected in the change in productivity and pressure build-up behavior. A study of these changes is also presented in this report. RESERVOIR ANALOGS The X-ray shadowgraph technique, employing miscible displacement in porous models, has been used in the study of the influence of fractures on pattern sweep-out efficiency. The X-ray shadowgraph procedure is described in detail in an earlier report8. Fractures were represented by leaving the proper portion of the model surface exposed to either injection or production. This assumes the fracture resistance to be negligible compared to that of the formation. Actually the flow resistance in propped fractures obtained in the field is sometimes not negligible so that the results with this model indicate the maximum influence of the fracture. Two types of models were necessary to represent vertical fractures in a five-spot flood. These pattern elements are illustrated in Fig. 1. In studying the influence of the horizontal fracture, only one well spacing length to thickness ratio of 50 was used. The pool unit of a Carter Electric Analyzer was used in studying the influence of fractures on productivity and build-up behavior. The square drainage system of a well was represented by a network of 576 elements of equal volume and resistance. One-fourth of this drainage area was studied as a model unit using a network of 144 condensers and resistors. Vertical fractures were represented by a shunt directed from the well perpendicular to the drainage boundary. Horizontal fractures were represented by a circular shunt. Resistance of a shunt was varied in representing different conductivities for the fractures. FRACTURE DIRECTION AND LENGTH The direction at which a vertical fracture extends into the formation and its length and conductivity influence the sweep behavior. The two

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and reGneries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Car1sbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies. Prospecting Since outcrops of potash are nonexistent, prospecting is accomplished by drilling and coring of the salt section to establish the grade, thickness, and outline of the potash beds contained in the salt deposits. Information regarding the nature of the formations in the cover of 400 to 600 ft thick over the salt and potash beds is also obtained from drill cuttings in the same operation. By proper interpretation of assembled data the best location for shafts may be determined. The overburden varies in character but consists in general of interbedded shales, sand, gravels, limestones, and anhydrite beds. Water, in unpleasant quantities, especially in the sands and limestones, often completes the geologic section. Some of the shaftas in the area have been sunk without undue difficulties, others have been delayed by flows of water. Most of the shafts are concreted from the surface to the salt section. Each of the three mines in the Carlsbad area has one shaft for hoisting ore and one for hoisting men and supplies. Mining Methods Information acquired from initial drilling and prospecting affected the choice of mining methods. Since the tabular, slightly rolling deposits were similar to coal seams, the room-and-pillar system used in coal mining was adopted by all the companies. Pillars have not been removed in any of the mines on a large scale. One company has conducted experimental robbing of pillars in one restricted area. Where it is known that overlying strata contain water in large amounts, it is not considered practical to risk flooding of the mines by removing pillars without fill. Some thought is now being directed toward development of economical methods of filling for pillar recovery. The problem is not identical at the three mines and local conditions will govern the methods employed for eventual pillar recovery. The important point is that, with large reserves, it has not been necessary to resort to mining of pillars for adequate production. The ore deposits are laterally extensive but are irregular in shape and lie at a depth of 700 to 1100 ft below the surface. The major operations of all mines are on the same bed strati-graphically, except for the langbeinite level at International Minerals and Chemical Corporation. The deposits are apparently not connected and in many parts of the deposits being mined, "salt horses" or barren zones occur. From 400 to 700 ft of salt with minor beds of polyhalite and anhydrite lie immediately above the ore horizon. The ore differs from the salt only in the potassium chloride content and color due to small amounts of iron associated with the sylvite, giving the ore a somewhat mottled red and white cast. Thickness of the ore varies from 5 to 14 ft. Rooms and break-throughs in the mines vary from 24 to 40 ft in width, the overlying salt forming an excellent roof and providing safe mining conditions. Almost no timber is used in any of the mines for roof support. Drilling is normally the first step in mining the face of a room. Electric motor driven auger drills are used in the area. Jack hammers were used to some extent when the mines were first opened but the ore is easily drilled if bits are sharp and the coal type

Jan 1, 1950

By Ellis Clark

The greater portion of the brown ore in the vicinity of Easton, along the north slope of the Lehigh Mountain or Durham range of hills, is obtained from mines instead of from open cuts or quarries, as is the case in the ore-beds in the western part of Northampton County, in Lehigh County, and in Berks County. The reasons for this method of procedure are various, and the principal causes of the shaft and regular mine system of working being adopted instead of the open air cuts, are: First, the large amount of stripping that would be necessary, as the richer and more valuable portions of the ore do not appear to be found as near the surface as those in other portions of the Kittatinny valley; second, the occurrence of the ore in regular beds, interstratified with the clay, and, to a less extent, in pockets or erratic deposits, as is the case in the mines of Lehigh County; and third, on account of many of the mines being situated at the immediate base of the Lehigh Mountain, where the surface water would be in such large quantities as to be with difficulty handled, and where the subsequent caving in of the sides of the open cut would be almost certain to expose the gneiss rock, which is water-bearing, the large quantities of water coming from which would probably drown out the ore-bed. Shafts, and a regular system of gangways and mining are therefore required by the configuration of the surface, the depth of the deposits and their geological structure. The ordinary size of the shafts is about four feet square, but where an extensive plant of pumping machinery is required the size may be increased to eight feet by six, with two compartments for the hoisting and pump-shaft respectively. A man-way, consisting of ladders with rests at intervals of twenty or thirty feet, is comprised in the pump-shaft, the wire rope being used for purposes of ascent and descent only in exceptional cases, on account of accidents which

Jan 1, 1879

By H. J. Hand

STATISTICAL methods are becoming increasingly important for inter-preting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of vari-ables more or less constantly tending to affect it. As pointed out by Daeves, 2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. ?

Jan 1, 1938

G. W. TRAER (author's reply to discussion*).-Prof. Parr's discussion develops two points, upon which it seems desirable to comment. First, as to putting through a large enough tonnage to secure economic operation. At each manipulation of each oven 1500 1b. (680 kg.) of coal will be charged and the resultant coke discharged from a like amount of coal. . Sixteen slabs will be discharged at each manipulation, each approximately 5 ½ in. by 11 in. by 6 ft. (14 cm. by 28 cm. by 1.8 m.). The operating schedule of a commercial plant, based upon our observations and calculations, indicates a "through put" of at least 12 tons of coal per day for each oven. We have made these figures conservatively and feel confident of materially exceeding them in a fully developed operating system. Our oven plant, with containers, will not cost as much as high-temperature plants of the same capacity. They do not require container equipment; but this is much more than offset by the cost of the great basal heat regenerative flues. Our operating requirements are quite susceptible to the application of mechanical devices and we believe our labor cost will be well within the necessary limit. Second, as to Fig. 1 in my paper, showing the specific gravity' of the tar. It Was not intended to show that the specific- gravity of -the tar rises With decreasing heat, since of course the contrary is the fact. One of the curves shows the relation between temperature and specific gravity and the other the relation between temperature and- yield. Our consulting engineer prepared the chart according to his customary method for showing two dimensions.

Jan 1, 1919

By I. R. Kramer

A study was made of the effect of surface-active agents an copper, gold, and zinc single crystals as well as polycrystalline aluminum. The study on coppw showed that the maximum effect of the surface -active agent occurred at the same concentration of the solution as that at which the rate of solution of the copper soap was the greatest. Surface -active agents did not affect the creep behavior of gold or freshly polished zinc specimens. The creel-, rate of zinc specimens in a solution containing a surface-active agent zoas always lower than that of freshly polished specimens. In previous papers1'2 it was reported that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing dur- ing tensile deformation, it was found that the slopes of Stages I, 11, and In were decreased and the extent of Stages I and I1 were increased when the rate of metal removal was increased. The results of the investigation of surface-active agents showed that changes in the slopes and extents of Stages I and II occurred when single crystals of aluminum were deformed in tension in a bath containing solutions of paraffin oil and stearic acid. The amount of change was a function of the concentration of stearic acid and the maximum effect occurred at a concentration of 0.002 mole per liter. These results were interpreted2 in terms of the rate of solution of metal soaps which form as a result of the chemical reaction between the surface-active agent and the metal. According to this interpretation, the "weakening" effect is controlled by the rate of solution of the soaps which depends upon the concentration of surface-active agents. At low concentrations, the number of metal soap molecules formed is low; at high concentrations, the rate of solubility is low, because of the high degree of saturation.

Jan 1, 1963

By ALEXANDER L Hay, Alexander L.

THE Sydney coal field, the largest and most valuable in Nova Scotia, is on the northeastern coast of the Island of Cape Breton, extending from Mira Bay on the south to Cape Dauphin on the north, a distance of 30 miles, and has a general dip northeast under the sea. The field embraces the mining villages of Morien, Birch- grove and Reserve and the towns of Dominion, Glace Bay, Waterford and Sydney Mines. The city of Sydney is about midway between the northern and southern extremities of the field and on the western fringe of the productive coal measures. Sydney harbor crosses the coal field, cutting off direct rail connection between Sydney Mines and the greater part of the field to the southeast.

Jan 1, 1928

By Craig R. Barrett, Alan J. Ardell, Oleg D. Sherby

It is shown that the apparent activation energy for creep of pure poly crystalline metals increases with increasing temperature in the temperature range 0.5 to 1.0 of the absolute melting temperature. This increase is probably associated with the influence 0-f the elastic modulus on the creep rate. By accounting for the variation of Young&apos;s nodulus with temperature, the true activation energies for creep of pure cadmium and aluminuvl are shown to be equal to the activation energies for self-diffusion in these metals, within experimental error, at all temperatures above 0.5T,. New creep parameters are proposed for cmrelation of steady-state creep rate and time-to-rupture data. These are respectively, where u is the creep stress, E is Young&apos;s rrodulus, i,is the steady-state creep mte, t, is the time -to-rupture, and D is the self-diffusion coefficient [equal to Do exp (-QSd/RT)] . It has been established experimentally1 and theoreticallyZm4 that high-temperature creep of poly-crystalline pure metals is a thermally activated process and may be represented by the general expression where <, is the steady-state creep rate, A is a constant dependent on the internal structure of the material, f is some function of the applied stress (0) and test temperature (T), and D is the self-diffusion coefficient. If D is separated into its temperature-dependent and independent portions, then it is possible to rewrite Eq. [I] as where Qsd is the activation energy for self-diffusion. Assuming a simple Arrhenius-type relationship between creep rate and temperature at a given constant stress, the apparent activation energy for creep, Q,, is given by the expression It is obvious that if is not a function of temperature It has been shown that the steady-state creep rate for pure polycrystalline metals1 can be represented by where S is a constant, L is the grain diameter, E is the isotropic polycrystalline (unrelaxed) elastic modulus, and n is a constant equal to approximately 5 over a wide range of stress. The apparent activation energy for creep calculated from this expression at constant grain size and stress is given by

Jan 1, 1964

By F. B. Sherman, Keros Cartwright

Sanitary land filling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Knowledge of ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for natural limitations at a particular site. Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites; (2) site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources; (3) research on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills; and (4) formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers. Throughout history, man has disposed of unwanted materials by dumping. As urbanization has increased, haphazard dumping practices have given way to disposal under more controlled conditions because of increasing congestion of population and production of waste and greater concern for public health and environmental amenities. Many states and communities have already outlawed open dumping and open burning of refuse. The only practical methods of disposal of large volumes of refuse, therefore, are contained, high-temperature incineration, or burial in a sanitary landfill. In Illinois, regulation of solid waste disposal has been delegated to the Environmental Protection Agency. Each session of the legislature since 1965 has passed increasingly strict laws regulating waste diposal. As a result, the work of evaluating sanitary landfill sites has increased significantly for both the Department of Public Health, now the Environmental Protection Agency, and the Illinois State Geological Survey, which advises the Agency on matters of ground-water geology and pollution. In fact, our ground-water staff spends as much time on studies relating to waste disposal, primarily sanitary landfills, as on ground-water resource studies. Many other geological agencies are experiencing similar demands for increased assistance in solving waste-disposal problems. This paper summarizes some of the salient features of the sanitary landfill concept, describes activities of the Illinois Geological Survey in ground-water and engineering geology relating to landfills, and suggests policies that need consideration. A sanitary landfill is located and operated in such a way that vermin and pests, nuisances, and degradation of air and water are kept at acceptable levels. Some of the physical requirements of a sanitary landfill are all-weather roads for year-round access, fences to retain blowing paper, a daily cover of at least six inches of suitable earth material, and a final cover of at least 2 ft of earth material. Dumping into or adjacent to standing water generally is not allowed. Two common operating techniques are used. In the first, trenches are dug, the refuse is placed in them, and the earth removed from the trenches is used to cover the waste. In the second method, area fill, refuse is placed in low ground and covered with earth from adjacent high areas. The hydrology of the site is a prime consideration in locating sanitary landfills. Putrescible refuse, if saturated above field capacity, produces a leachate that usually has a high concentration of dissolved solids.2 As the leachate also acts as an agent for transporting bacterial pollutants, it constitutes a potential pollution hazard. To reduce the production of leachates, the topography of the landfill area should be such that surface water will not flow into or through the fill. Operations that will result in refuse disposal below or near the highest known water-table elevation may be required to take corrective or preventive measures to protect the ground water. In practice, under humid conditions such as prevail in Illinois, locations where disposal can take place above the water table are relatively few because surficial materials are commonly fine-grained, which permits slow gravity drainage and results in high degrees of saturation (100% moisture content) near the surface. At some sites, although disposal has taken place above the water table, ground-water mounds have developed, resulting in permanent saturation of the refuse. Permeability barriers usually are required to protect the ground-water reservoir from degradation by leachates. The convention in Illinois is to have a minimum of

Jan 1, 1972