Search Documents

By Hugh Tiemann

(San Francisco Meeting, September, 1915) THE desirability of employing the centigrade scale for the measurement of temperatures is becoming more and more recognized in this country, particularly in view of the fact that this scale is used almost exclusively in technical papers and publications-exclusively in those published in French or German. There are, however, a large number of factories and laboratories which still employ the Fahrenheit scale. It therefore frequently becomes necessary to convert one into the other and the accompanying chart (Fig. 1) has been found very convenient for this purpose.

Jan 6, 1915

US 4,190,436 - In the cyanide leaching of gold ore in tailing or ore dump piles, or gold ore in vats or on pads, the ore is agitated and oxygenated by introducing timed bursts of air, along with cyanide in a cyclic or regulated manner. The leach liquor is drained from the material by providing a continuous flow of air. Fines are homogenously mixed, thereby reducing channelling In the ore bed. Yield is improved and cyanide consumption lessened. R M. Hughes Feb. 26, 1980. 7 pp. (75-105). Filed. 12-20-77 (862,335).

Jan 1, 1982

By A. N. Holden, J. H. Hollomon

A. H. COTTRELL* and A. T. * Dept. of Metallurgy, Birmingham Univ., England. CHURCHMAN*—We have been making some experiments recently very similar to those reported by Messrs. Holden and Holloman. Wires of Armco iron, 0.077 in. diam. were decarburized in wet hydrogen until the yield point was removed; they were then extended 31/4 pct and annealed at 880°C for 120 hr in dry hydrogen. This process produced large crystals which extended through the cross-section and were about 3/4 in. in length. Since the length of each crystal

Jan 1, 1950

By Oswald J. Heinrich

In conclusion of a series of deep exploration-borings with the diamond drill, I beg to submit the following statements, supplementary to those in my former papers on this subject: Since my communications read at the St. Louis Meeting, in May last, I have finished two more borings, one terminating at the depth of 922 feet 7 inches, the other at the depth of 715 feet 6 inches. The results in regard to time and expenditure have been highly favorable and fully confirmatory of my opinion stated in previous

By Oswald J. Heinrich

(Supplementary Paper.) IN conclusion of a series of deep exploration-borings with the diamond drill, I beg to submit the following statements, supplernentary to those in my former papers on this subject: Since my communications read at the St. Louis Meeting, in May last, I have finished two more borings, one terminating at the depth of 922 feet 7 inches, the other at the depth of 715 feet 6 inches. The results in regard to time and expenditure have been highly favorable and fully confirmatory of my opinion stated in previous

Jan 1, 1875

By John F. Frawley

This article in all probability will raise some serious doubts as to whether the coal industry-without a national, long-range commitment to coal-can, or should, attempt to meet the capital demands necessary to double coal production in the next 10 years. AMAX Coal, incidentally, doubled its annual coal productive capacity in the past five years from 11 million tons in 1969 to 22 million tons in 1974. Our 1973 annual report stated that we were aiming to triple our 1973 capacity to 50 million tpy by 1978.

Jan 5, 1975

By C. L. Baker

The total production of petroleum in the Gulf Coast in 1927 was 54.541.180 bbl., .5.655.665 bbl. more than in 1926. The Texas total was 49.129.910 bbl. (Table 1) and the Louisiana tota1 5.411.270 bbl. (Table 2). Louisiana production decreased 278.028 bbl., compared with that of 1926. Spindletop produced nearly 44 per cent. of the Texas total. Initial production in Louisiana amounted to 62.865 bbl. and in Texas to 352.955 bbl.' The Oil and Gas Journal gives a total of 1145 wells

Jan 1, 1928

By K. Shoji, R. Hogg, L. G. Austin

The flow of dry powders through continuous ball mills has been investigated. Based on a physical model of the system, expressions have been derived which relate the holdup of material in the mill and its variation along the length of the mill to the mill dimensions, speed of rotation, material feed rate, and the mill discharge geometry. Experimental results obtained in a small (4 in.) mill using 3/8-in. steel balls and a feed of silicon carbide particles are in good agreement with the prediction of the model.

Jan 1, 1976

By J. F. Pashak, T. E. Leontis

The effects of zirconium on the properties of sand cast Mg-rare earth metal alloys were discussed in detail in an earlier publication.' It was shown that a significant improvement in strength properties at temperatures up to 400°F resulted from the zirconium addition. In general, the properties of cast Mg-Didymium-Zr alloys were superior to the corresponding alloys containing Mischmetal and the optimum rare-earth level was approAmately 3 pet. Jessup, Emley, and Fisher have also shown the advantages of didymium in Mg-rare earth-Zr alloys, 2

Jan 1, 1961

By C. C. Hatch, A. L. Mular

The methodology employed to develop a digital simulation of the Brenda Mines Ltd., Peachland, B. C., secondary crushing plant is described. Methodology includes data acquisition, data adjustment, model building, and the construction of a simulator structure. The simulator was utilized to study the effects of secondary and tertiary crusher close side settings, secondary screen opening, plant feed rate, and percent + 1 in. in the feed on the following responses: percent - 1/2 in. in the final product, plant reduction ratio, circulating load ratio, and screen efficiency. Results are presented in graphical form.

Jan 1, 1983

By William N. Matheson

The major consideration in any management and engineering decision is the economic evaluation of factors. The right decision is the best cost decision, provided of course that it is the safest. Changes, improvements, and advances in mining technology, as in any business, come about through the pressure of economics in combination with the inventiveness and engineering abilities of efficient mine operators. Without proper economic evaluation and an appreciation of profit and loss of an operation, advances in mining methods would come about at a slow pace, if at all.

Jan 4, 1959

By means of top-slicing methods, wide veins, masses, or thick beds of soft ore may be mined, where the caving of the overburden is of no consequence. The ore is mined in a series of horizontal floors or slices, taken in descending order, from the top of the deposit. Each floor is mined in small sections, the roof of each section being allowed or forced to cave before an adjacent section is attacked. The method as used in two mining districts—Marquette, iron, and Pachuca, silver-gold—is described in the two papers following:

Jan 1, 1925

By R. H. Thorpe

Longwall working in Britain developed to overcome problems arising from depth of seams causing roof and ventilation difficulties. This system became very widespread particularly in the thicker seams, where faces of up to one mile in length were not uncommon. In the thinner sections, in order to remain competitive, the longwall undercutting machine was developed. Following the development of the coal cutter, every other aspect of the face operation was examined and mechanized as it became a bottleneck to output and efficiency. The face system itself was modified and workings concentrated with the same objectives.

Jan 1, 1977

By Paul A. Taylor

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance. Substantial progress has been made in classifying different types of these deposits according to general features, internal structure, mineralogy, and origin. In some cases it has even been possible to block out tonnage reserves in advance of mining. It is still easy, however, to make highly erroneous predictions after a preliminary examination of a pegmatite prospect. Pegmatites are important to the economic well being of the country and to its military security. They furnish virtually all the feldspar, strategic mica, beryl, columbium, tantalum, and caesium utilized in the United States, as well as sundry other minerals and significant amounts of lithium and rare earth minerals and gems. With the exception of vermiculite, occasional ilmenite-rutile, and perhaps soda-lime feldspar and garnet deposits, basic pegmatites are of little economic importance. Consequently in this paper, as in common parlance, the term pegmatite generally relates to coarsegrained acidic rocks or what is aptly called giant granite. Available data indicating the size and importance of the production and trade in specified pegmatite minerals are summarized in Table I. Geological Features Much of the latest thinking on the economic geology of pegmatites is now available in a 115-page monograph' by a group of experts who participated with geologists of the Federal Geological Survey in the widespread wartime investigations. Doubtless the most significant feature of the monograph is indicated by the title, The Internal Structure of Pegmatites, but it also contains a vast amount of other new information and includes the assimilated concepts of many earlier writers, whose works are given in a comprehensive list of references. The shape, size, attitude, and continuity of many pegmatite bodies is controlled by the structure of the older rocks in which they occur. If the older rocks are easily penetrated, e.g., biotite schist, most of the pegmatites in a given district will be found outside the parent granite mass as exterior pegmatites. Marginal pegmatites are more prevalent if the older rocks are massive, unsheared, and sparingly jointed. Networks of pegmatites are abundant in highly-jointed rocks. In strongly foliated schists the bodies are usually lenticular, whereas in highly-folded areas they assume tear drop, pipe or pod-like, bow-shaped, or sinuous forms. Jahns2 recognizes five major shape classes: l—dikes, sills, pipes, and elongate pods; 2— dikes, sills, pipes, and pods with bends, protuberances, or other irregularities; 3-—trough-or scoop-shaped bodies with or without complicating branches; 4—bodies with the form of an inverted trough or scoop; and 5—other bodies, including combinations of the above and miscellaneous shapes. Many pegmatite deposits are scarcely big enough to be recognizable as such. Most of them, in fact, are small tabular deposits less than 4 in. wide and usually without economic concentrations of minerals. On the other hand, some pegmatites are more than a mile long and over 500 ft wide. The ratios of length to breadth range from 1 : 1 to 1 : 100. Although the vertical dimension bears no invariable relationship to strike length, tabular deposits or large lenses are often symmetrical enough to show nearly as much continuity down dip as in their horizontal extension, and some pipes or pods are amazingly persistent in the vertical plane. Small pegmatites often string along a fairly definite trend line; in a given district major bodies may lie roughly parallel, and where only a few of them do not, the erratically disposed bodies generally differ in composition from those conforming to the regular pattern. This does not apply, however, in all districts. Characteristically, pegmatite veins pinch and swell or split into branches. When they pinch out entirely it is often possible to find a new body by prospecting the extension of the strike or dip, but the chances of finding a hidden deposit are ordinarily too uncertain to justify much subsurface prospecting. Diamond drilling may yield valuable information as to the continuity of known deposits whose upper portions are well-exposed. Some deposits, in fact, can be proved up for hundreds of feet by surface trenching and then intersected by drill holes at various depths like any other vein-like deposit. Others twist and branch, apparently defying all efforts to explore them short of actual mining.

Jan 1, 1954

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By J. B. Cheatham, J. W. McEver

A laboratory investigation of the behavior of casing subjected to salt loading indicates that it is not economically feasible to design casing for the most severe situations of nonuniform loading. When the annulus is completely filled with cement, casing is subjected to a nearly uniform loading approximately equal to the overburden pressure, and, although the modes of failure may be different, the design of casing to withstand uniform salt pressure can be computed on the same basis as the design of casing to withstand fluid pressure. Failure of casing by nonuniform loading in inadequately cemented washed-out salt sections should be considered a cementing problem rather than a casing design problem. INTRODUCTION Casing failures in salt zones have created an interest in understanding the behavior of casing subjected to salt loading. The designer must know the magnitudes and types of loading to be expected from salt flow and he must be able to calculate the reaction of the casing to these loads. In the laboratory study reported in this paper, short-time experimental measurements of the load required to force steel cylinders into rock salt are used as a basis for computing the salt loading on casing. These results must be considered to be qualitative only since rock salt behaves differently under down-hole and atmospheric conditions and also may vary in strength at different locations. The beneficial effects of (1) cement around casing, (2) a liner cemented inside of casing, and (3) fluid pressure inside of casing in resisting casing failure are considered. ROCK SALT BEHAVIOR UNDER STRESS The effects of such factors as overburden loading, internal fluid pressure, and temperature on the flow of salt around cavities have been studied extensively at The U. of Texas. Brown, et al.1 have concluded that an opening in rock salt can reach a stable equilibrium if the formation stress is less than 3,000 psi and the temperature is less than 300°F. At higher temperatures and pressures an opening in salt can close completely. These results indicate that calculations based upon elastic and plastic equilibrium for an open hole in salt should be applied only at depths less than 3,000 ft. In most oil wells the tem- perature will be less than 300F in the salt sections, therefore no appreciable temperature effects are anticipated. Serata and Gloyna2 have reported an investigation of the structural stability of salt. .They assume that the major principal stress is due to the overburden. Other stresses can be superimposed if additional lateral pressures are known to be acting in a particular region. In the present analysis an isotropic state of stress is assumed to exist in the salt before the hole is drilled, since salt regions are generally at rest. This assumption is partially verified from formation breakdown pressure data taken during squeeze-cementing operations in salt. Experimental measurements of the elastic properties of rock salt indicate a value of 150,000 psi for Young's modulus and a value of approximately 0.5 for Poisson's ratio. A value of % for Poison's ratio with finite Young's modulus would indicate that the material was incompressible. Values ranging from 2,300 to 5,000 psi have been reporteda for the unconfined compressive strength of salt. These variations may be due to differences in the properties of the salt from different locations or at least partially to differences in testing techniques. Salt is very ductile, even under relatively low confining pressures. For example, in triaxial tests reported by Handin3 strains in excess of 20 to 30 per cent were obtained without fracture. When casing is cemented in a hole through a salt section, the casing must withstand a load from the formation if plastic flow of the salt is prevented. To determine the forces which salt can impose on casing, circular steel rods were forced into Hockley rocksalt with the longitudinal axis of the rods parallel to the surface of the salt. The force required to embed rods 0.2 to I in. in diameter and 1/2 to 1 in. long to a depth equal to the radius of the rods was found to be F/DL =28,700 psi (± 3,700 psi) , .... (1) where D is the diameter, and L is the length of the rod. CASING STRESSES Since an open borehole through salt at depths greater than 3,000 ft will tend to close, cemented casing which prevents closure of the hole will be subjected to a pressure approximately equal to the horizontal formation stress after a sufficiently long time. As a first approximation the horizontal stress can be assumed to be equal to the overburden pressure. This is in agreement with the suggestion by Texter4 that an adequate cement job can prevent plastic flow of salt and result in a pressure on the casing approximately equal to the overburden pressure. He also advocated drilling with fully saturated salt mud

Jan 1, 1965

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company's plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal 'acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

By R. G. Aspden

Crystals with an (001) [loo] initial orientation of an iron-base alloy containing 3 pct Si were cold rolled with and without the use of constraints. A major difference in the rolling and annealing textures was observed between crystals rolled with and without constraints. These data show that the contribution of constraints at grain boundaries in a poly crystalline sheet should be considered in applying textural data on single crystals to grains in an aggregate. SILICON-iron alloys with a cube texture have been recently developed and their magnetic characteristics reported.1-4 Of interest in the development of this texture were the textural changes of single crystals accompanying rolling and annealing and the influence of constraints at grain boundaries in an aggregate on the behavior of individual grains. The present study was primarily concerned with the effect of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001)[100]. Barrett and Levenson5 were among the first to observe an influence of constraints at grain boundaries on the textural changes of individual grains during deformation. They tested Taylor's6 theory of plastic deformation of face-centered-cubic metals in which deformation textures were predicted. About one-third of the grains in poly crystalline aluminum did not rotate as predicted. Grains of the same initial orientation were observed to rotate in different directions under the influence of applied stress and anisotropic flow of neighboring grains. Recently, the various inhomogeneities of flow of crystals in an aggregate have been studied7'8 and reviewed.9-11 Barrett and Levenson" rolled (001) [loo] iron single crystals inserted in close-fitting holes in copper to limit lateral flow and to simulate rolling of grains in an aggregate. Deformation bands were formed after a 90 pct reduction in thickness, and the cold-rolling texture contained two components described by rotating the (001)[100] about 35 deg in both directions around the normal of the rolling plane. No annealing textures were reported. Chen and Maddin13 rolled molybdenum single crystals initially (001) [loo]. The crystals were mounted between two hardened silicon-iron plates and 96 pct reduced in thickness by rolling at a low rate of reduction, about 0.0001 in. per pass. The deformation texture had the mean orientation of (001) [loo], and the azimuthal spread included orientations described by rotating (001) [loo] about 35 deg in both directions about the pole of the rolling plane. The presence of deformation bands were not reported by Chen and Maddin or detected in subsequent work of Ujiiye and Maddin.14 The ideal orientation of the annealing texture was (001) [loo]. Recently, Walter and Hibbard 15 reported on the textures of 3 pct Si-Fe alloy crystals initially near (001) [loo]. Each crystal was in an aggregate cut from a columnar ingot. After 66 pct reduction by rolling, the texture consisted of two symmetrical components which had the orientations described by rotating (001) [loo] about 30 deg in both directions about the pole of the rolling plane. Annealing texture was near (001) [loo]. In the above work, the textures of body-centered-cubic crystals were studied after rolling under the influence of constraints. The deformation textures varied from (001) [loo] to near the (001) [110] type and appeared sensitive to the manner in which the crystals were rolled. No textural data were available on the effect of rolling (001) [loo] crystals with and without constraints. The purpose of the present work was to evaluate the influence of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001) [loo]. Rolling and annealing textures were studied for a) crystals rolled with no constraints at different rates of reduction, and b) crystals rolled with constraints imposed by neighboring grains and by plates between which a crystal was "sandwiched". PROCEDURES AND EXPERIMENTAL TECHNIQUES Data are presented on four crystals which are representative of several crystals studied. The orientation of each crystal prior to rolling was (001) [loo] as determined by the Laue X-ray back-reflection method," i.e., each crystal had an (001) within 3 deg of the rolling plane and [100] within 3 deg of the rolling direction. These crystals were obtained from two iron-base alloys containing 3 pct Si by weight which were prepared by vacuum melting electrolytic iron and a commercial grade of silicon. Crystals 1, 2, and S-1 were cut from a large single crystal grown from the melt of one alloy by the Bridgman technique17 in an apparatus described by

Jan 1, 1960