Search Documents

By P. G. Salom

The manufacture of steel castings has become one of the important industries of the times. The late Mr. Alexander I,. Holley published in 1878, in the Metallurgical Review, an able paper, entitled "Solid Steel Castings," showing how all manner of castings could be made advantageously of steel. Mr. Holley had then but lately returned from the great iron and steel works of Terrenoire, France, which were engaged, I believe, almost exclusively on large castings, of a simple type, for the government,, and were repeating the same operation from day to day. These conditions are, as experience has shown, very different from those of ordinary practice in miscellaneons castings; and Mr. Holley might have been less confident if be had actually gone into the business. More than seven years have passed ; and as yet the magnificent possibilities held forth in his paper have not been realized. There are only six steelcasting establishments in the United States, and their total output of castings is certainly not as much as 20,000 tons per annum, and probably not more than 10,000 tons; whereas it should be over 200,000 tons to supply the needs of the country. A large number of so-called steel castings are made, however, which are nothing more than malleable iron. The best of these castings are made from a superior white pig, as low in silicon and

Jan 1, 1886

By William Plank

In practically all rock-excavation problems there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State-highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before' the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was, placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation.

Jan 1, 1935

By E. F. Steeb, P. C. Rosenthal

BlANKS 8 in. long were cut from the as-received bar stock and austenitized at 1560° F for 1 hr, oil quenched, tempered at 1140°F for 1 hr, and water quenched. The heat-treated blanks were machined into tensile specimens which were subsequently used for the straining operation. Some of the tensile specimens were temper embrittled at 900°F for 24 hr and air cooled prior to or following the straining operation. The specimens were strained in tension up to 5 pct total strain (elastic plus plastic) either at room temperature or at 900°F. The reduced sec- tion of the tensile specimen employed was 5 in. long and 0.600 in. in diam. This size specimen was sufficiently large to permit two standard Charpy impact bars to be machined from it. One group of specimens was temper embrittled at 900°F for 24 hr under stress of about 20,000 psi applied with a hydraulic tensile testing machine. Approximately 0.34 pct plastic strain occurred during this treatment. A comparison of series "A" and "B" data in Table I at 0 pct strain, reveals that the steel was rather highly susceptible to temper embrittlement, the embrittling treatment causing the transition temperature to rise 165°F. The 28 ft-lb level, which was near the center of the sharp-rising portion of the transition curve, was selected as the

Jan 1, 1959

By C. C. Harris

The 3-parameter equation* was introduced1 as having the necessary form and flexibility for describing the major features of size distribution curves. Also, Eq. 1 was shown to contain most of the widely used 2-parameter equations as special cases. Special methods are necessary in order to determine the parameters of 3-parameter equations by graphical means. The procedure given previously required double graphical interpolation followed by regraphing the interpolated data. The theoretical basis of the method was a difference equation eliminating y. Several other methods for obtaining the parameters have been under development and one method appears to overcome the disadvantages of the earlier method and satisfies several procedural requirements. The points in favor of the new method as compared to the earlier method are as follows: 1. Estimation of the quality of fit is direct, and is in fact an essential part of the procedure. 2. The data is plotted directly without the necessity of interpolation from a graph. 3. The method makes use of Rosin-Rammler2 paper which because of expanded scaling in the coarse sizes leads to improved accuracy1 as compared with the log-log plot for the Gates3-Gaudin4-Schubann5 representation. 4. There is a gain over the earlier method in overall accuracy and in simplicity.

Jan 1, 1970

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By Thorp D. Sawyer

In June 1914, one week before I was to be awarded my sheepskin in upper New York State, I received a telegram from New York City which read "Can offer you position as engineer in Chile at $115 a month contract for one year. (signed) Chile Copper Co." That night, Friday, I took a sleeper to New York and arrived at the Guggenheim Brothers' company office at 165 Broadway, just as it was opening up on Saturday morning. Saturday was no holiday in that era. Presenting the telegram at the office, I was ushered into a sub-executive's office and shown a mimeographed contract which 1) agreed to pay me $115 per month from the date of leaving New York until I returned, and with travelling expenses both ways, 2) fixed a charge of $46 per month for board and lodging in company quarters, and 3) stipulated a contract term of one year with the right to retain my services for another year if the company so elected. While a bit huffed at the year's "kicker" I nevertheless accepted. I was then told to prepare to leave the following Wednesday (June 17) on a United Fruit Co. steamer for Panama. Objecting that I still had to receive my degree on the 17th and had planned a vacation in Ohio for a week or so…

Jan 12, 1960

By Edward L. Clark

The year 1954 witnessed great activity in the field of geology as applied to mining. The search for in nearly all districts is becoming more and more intensified as established reserves are being depleted. Much geologic work has been directed to finding extensions of known orebodies, but prospecting in new areas has constituted a large part of the program of many operators. The acute need for additional reserves has brought into the search all the tools known to the geologic profession. This is reflected directly by frequent references to geophysical and geochemical methods in the regional reviews that follow. The lone prospector of the early days of metal mining has been eliminated almost completely by modern scientific methods involving surface and subsurface geology, exploratory drilling, geophysics, and geochemistry. Nearly all new exploration is based on long-range programs coupled with studies of regional geology to determine the structural environment of areas of mineralization. The success of this approach has encouraged new operators in the field of exploration to adopt similar policies. Only in the search for uranium ores is the individual prospector still active, but the familiar picture of the burro heavily loaded with grubstake, gold pan, and pick and shovel has been replaced by the Geiger counter and the scintillometer carried by hand, by truck, or by airplane.

Jan 3, 1955

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Present day design is a trial-and-error approach based mostly on experience. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper reports on a three-year research effort directed to an improved design of room-and-pillar coal mining in the U.S.A. Essentially the study consisted of three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and-pillar coal mining in the United States. Furthermore, three novel approaches were utilized during this research: i) the "petite sismique" technique was assessed for possible determination of coal pillar deformability ii) the "Geomechanics Classification" was extended for determination of safe roof spans in room-and-pillar coal mining. iii) a national survey of the current design practice and mining dimensions was performed with the aim of assessing factors of safety for room-and-pillar coal mining The outcome of this work, which is summarized in this paper, is a design code for room-and-pillar mining in the United States.

Jan 1, 1983

By A. J. Lynch, E. V. Manlapig, J. H. Fewings, D. J. McKee

Progress in the development of an automatic control system for the chalcopyrite flotation circuit at Mount Isa Mines Limited is discussed. Preliminary studies have shown that the operating grade/ recovery curve for a sulphide flotation circuit is established by rougher-scavenger behaviour and the operating point on that curve by cleaner-retreatment behaviour. The control strategy of the rougher-scavenger banks involved regulation of xanthate to maintain recovery and control of air to seek the optimum grade/recovery curve. Control of the cleaner circuit to maintain the correct operating point of the plant relative to the ore entering it will be by air. Pulp levels will be used as an additional controllable variable in due course. Sensing instruments include a “Courier” on-stream analyser and several mass flow metering systems each of which contains a magnetic flow meter and a gama gauge. Measurements of concentrate grades and recoveries are made as early as possible in the rougher bank so that a change in the ore entering the plant can be detected as soon as possible. Over a period of six months from initial control systems application, computer control of xanthate resulted in an overall reduction in consumption of 10%. Experimental work has indicated that improved metallurgical performance will result from the introduction of additional air and level control loops.

Jan 1, 1976

By Persifor Frazer

(Read at the Wilkes-Barre Meeting, May, 1877.) A CLASSIFICATION of natural objects is usually based either upon some fundamental and permanent attribute of the thing itself (as in the case of scientific classifications), or it embraces one or more generalizations convenient for use in ordinary life. Thus, it suffices for the statistician to, know that so many tons of fish are annually taken by our fishermen, and that they realize so many thousands of dollars, whereas to the student of natural history the anatomy, habits, and relationships of the animals are of chief interest, as settling their respective places in the scale of animate nature. Many different classifications of coals have been attempted, as one would naturally anticipate from the immense extent of the coal trade, and the different localities whence the supply was derived. The English divisions were prevalent up to the date of the publication of the last geological survey of the State, except so far as they were modified by local designations. Indeed, Rogers' classifications made very little alteration in the English nomenclature, as may be seen by comparing. the tables given below. To commence with the different kinds mentioned in Ure's Dictionary of Arts, Manufactures and Mines of 1845 " 1. Cubical Coal.-Black, shining, compact, moderately hard and easily frangible. Comes out in rectangular masses, of which the

Jan 1, 1878

By Paul C. Merritt

Chrysotile asbestos producers in Quebec may soon experience a unique situation-i.e., strong competition from American ore sources for the short fiber market west of the Mississippi River. This com- petition will be forthcoming from Copperopolis and Coalinga, two deposits now being developed on opposite flanks of the San Joaquin Valley in central California. The combined output now planned from both deposits is 100,000 tons annually, equivalent to about 50% of the annual market demand in the western, central and Gulf States, and more than twice the tonnage sold in 1960 by all other American asbestos producers combined. The principal companies involved in these new undertakings are Jefferson Lake Asbestos Corp. (subsidiary of Jefferson Lake Sulphur Co.), Hidden Splendor Mining Co., Coalinga Asbestos Co. (Johns- Manville Corp. in conjunction with Kern County Land Co.), Union Carbide Corp., and Asbestos Corp. Ltd. Jefferson Lake's principal interest is at Copperopolis where the company's new 70,000-ton per yr mill recently went on stream. The company also holds some claims at Coalinga, but this latter area is better known as the site where Hidden Splendor, Coalinga Asbestos Co. and Todd Industries (a local company) have established operating mines and mills capable of turning out 30,000 tons of fiber each year. Coalinga is also the site of exploration by Union Carbide Nuclear and Asbestos Corp. Ltd.

Jan 9, 1962

By R. S. Dean

THE first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselin1 in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228° C. In the next year, Stead2 placed the eutectic temperature at 247° C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time the present investigation was started. He concluded' that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247°C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if any-thing, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);" the thermoforce by Rudolfi (1910),12 and Pelabon (1923);13 the specific heat by Durrer

Jan 2, 1926

By Harrison Souder

In view of the proposed visit of the Institute to Cuba this winter, the following brief sketch of the principal mineral deposits near Santiago de Cuba has been prepared largely from notes taken in February, 1903, during a visit to the mines then in operation in the province of Santiago de Cuba. Westward from Cape Maysi, the most eastern point of the island, the coast is rocky and uninviting. The usual course of the steamers is well in toward the shore, and the lines of stratification of the rocks can be distinguished clearly, the presence of iron or other ores being indicated by frequent blotches of mineral stain. One is impressed with the general rugged character of the southeastern coast-line,—an almost unbroken barrier of coral-limestone bluff's, full of caves and hollows, into which the surf rushes with a roar and bursts into tall fountains of spray. Beyond rises abruptly the Sierra Maestra range, whose sharp, peaked crest-line betrays its eruptive or igneous origin. From a height of about 800 ft. near Cape Maysi, this range gradually rises to the westward, attaining its maximum elevation of more than 8,300 ft. in the Pico Turquino, beyond Santiago. A general resemblance to the mountain-ranges of southern New Mexico is noticeable. At Daiquiri, 20 miles east of Santiago harbor, the extensive

Jan 1, 1905

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

By J. T. Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas of the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has also developed very rapidly recently and the various processes to which ,metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles. ATOMIC ARRANGEMENT IN CRYSTALS In the solid state all metals are crystalline. The atoms are arranged in, a definite symmetrical configuration, which is repeated at regular intervals, and thereby defines what we may term a lattice. Presumably . the atoms exist as positive ions. The dissociated electrons place themselves between groups of positive ions, and thus define a second lattice, an "electron lattice." From such a point of view, the crystalline forces which hold a metal together are the electrostatic attractions between positive ions and negative electrons. The particular type of lattice into which a metal crystallizes depends on the number of these lattice electrons given up by each atom, and is thus connected very closely with the chemical valence of the metal.

Jan 12, 1926

By L. W. McKeehan, W. C. Elmore

THE magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter' first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel' single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. SPECIMENS The following list describes the specimens used in the present investigation. DESIGNATION DESCRIPTION A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which he gave the following typical analysis: C, 0.05; P, 0.038; 5, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick.

Jan 1, 1935

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.'TheRittinger In its first form, as stated by P. R. Ritted.'tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin' as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.'TheRittinger In its first form, as stated by P. R. Ritted.'tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin' as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson' reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."' A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17' to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950