Search Documents

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By E. N. Cameron, H. M. Bannerman

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By W. Julian Parton

Treatment of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro-separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low-grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. Operation and Types oF Settling Equipment When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1947

By H. M. Bannerman, E. N. Cameron

INTRODUCTION DURING the years 1942-1944, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailed studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times, for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larrabee, A. H. McNair, J. J. Page, V. E. Shainin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. ANALYSIS OF WARTIME OPERATIONS In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 1/3 to 2/3 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the transition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1946

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By H. M. Bannerman, E. N. Cameron

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By W. Julian Parton

Treatment of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro-separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low-grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. Operation and Types oF Settling Equipment When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1947

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By Everett H. Graff, Ray H. Misener

THE Sol de Oro mine is in the province of Nazca, 487 km. southeast of Lima, and 60 km. inland from the coast at an elevation of 1200 m. above sea level. From Lima the mine may be reached in 8 hr. by automobile; 472 km. from Lima to Nazca over the paved Pan-American Highway and 15 km. from Nazca to the mine over a good graveled road. The trip from Lima can also be made in 2 hr. via the Faucett Air Lines which make two stops weekly at Nazca. The [Compania] Aurifera Nazca, owning and operating the Sol de Oro mine, was organized in Lima in 1930 by a group of prominent Peruvian mining men, including Ing. Carlos Alvarez Calderon, Dr. Alfredo Alvarez Calderón, Ing. Hector Boza, Ing. Jorge Félix Remy, Ing. Eulogio Femandini, Sr. Fernando Wiese, and Sr. Julio East. The nine claims in the Sol de Oro group owned by the company comprise an area of 52 square kilometers. Development of the property was not started until 1932 and only then under adverse conditions, owing to lack of transportation facilities. Mining machinery and other supplies could be taken as far as Ica by boat and railroad, but to transport them over the 180 km. of hot, sandy desert from Ica to the mine was a problem. There was no road in those days and only a few of the most venturesome truck drivers cared to contract the hauling. Another problem the company had to face was that of securing adequate labor. The Sol de Oro is in an agricultural region, and was forced to look to the near-by cotton plantations for men. Experienced men were imported from the "sierras," but they did not stay. The men are accustomed to high altitudes and cold climate and cannot easily acclimate themselves to the hot and arid coastal region. As a consequence the company has been forced to hire the inexperienced local laborers and train them for mining. The company has established three separate camps at the Sol de Oro property. Each is approximately one kilometer from the other and connected by auto road. The upper mine camp consists of living quarters for 300 workmen and their families, a general mine office, carpenter shop and timber-framing shed, compressor house, drill-sharpening and drill-repair shop, first-aid station, time office, school and store. At the central or "empleados" camp there is a 200-ton cyanide plant, general offices, warehouse, powerhouse, shops, laboratory, hospital, school, guest house, an 18-room hotel for the single staffmen, and 12 completely modern five-room cottages for the married staff employees. At the lower camp are living quarters for 200 workmen and their families, two general stores, a school and a small theater. Below this camp, along the river, are the company wells and pumping plant supplying water for mine, mill, and camp uses.

Jan 1, 1945

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By H. R. Peiffer

The increase in electrical resistivity, ?pT,at 78°K was measured as a function of elongation, E, at 78°K for a 2 pct (approximately) by weight finely divided alumina in silver material. The amount of increase in electrical resistivity (?pT) is a function of the amount of alumina present and can be represented by: ?pT = cen where c and n are constants. The constant c increases and the exponent n decreases with increasing alumina content. Approximately 33 pct of the resistivity increase is recovered upon annealing at room temperature. RECENTLY, dispersed phase alloys&apos; have shown promise for use at elevated temperatures. These materials have a high creep resistance, a high-temperature strength considerably above that of the pure matrix, and a high electrical conductivity. These materials also show other properties such as retardation of re crystallization and resistance to flow even above the melting point of the matrix.&apos; It is believed that high-temperature creep is retarded in these materials because the dispersed phase blocks the motion of dislocations. According to schoeck3 and also Weertman,4 the rate controlling process is the climb of dislocations around the dispersed phase particles. Any mechanical property of these materials, or any other material for that matter, can be explained on the basis of defect structures and their interrelations. It would certainly be interesting to learn something about the effect of a dispersed phase on dislocation densities and also their effect on point defect concentrations following cold work. This is the purpose of the research discussed herein. The method used was the measurement of the electrical resistivity as a function of elongation at low temperatures. This scheme has already been applied to the studies of pure metals.5 Electrical resistivity measurements conducted on pure metals such as copper, silver, gold, and so forth, have indicated that defects such as vacancies and dislocations are formed during deformation.5 It has been shown by van Bueren6 that the resistivity change, ?p, should increase with elongation, E, according to the following relation: Ap=Al/2 + B£3/2 where A and B are constants of the system; ?p is in µ? cm. The first term refers to the amount of resistivity change associated with line defects and the second term with the change associated with point defects. A later calculation yielded exponents of 3/4 and 5/4, respectively.6 Manintveld7 has shown that the resistivity of copper increases with strain according to a 3/2 power law, whereas van Bueren has shown that the resistivity of silver increases according to a 5/4 power law. Assuming then that van Bueren&apos;s calculations are correct, it appears that line defects contribute very little to the electrical resistivity. There is some doubt, however, as to the validity of van Bueren&apos;s expressions for all cubic metals.&apos; In fact, the data on copper and silver are not conclusive. In this in-

Jan 1, 1962

By C. L. Mantell

When considered from the viewpoint of world annual output, tin is one of the rarest metals. Its annual production is exceeded by that of iron, copper, lead, zinc. aluminum, magnesium; probably by that of the ferroalloys of manganese, chromium, and silicon, and possibly by the world production of sodium; while it exceeds only the output of such common metals as nickel, antimony, mercury, tungsten, molybdenum, silver, gold and the precious metals. Cassiterite, or tinstone, until the second World War was the only mineral that was an important source of tin. This mineral is frequently called "tin ore." The use of the term should be restricted to the ore containing the mineral, and not, in addition, to the concentrates of the mineral obtained from the ore or from stanniferous alluvial deposits. There is a general misuse of the term "tin ore" in the Malay Peninsula and adjacent localities, particularly where most of the mineral is obtained from secondary stanniferous deposits. The term "cassit-erite" is exclusively used in mineralogical, geological, and other scientific writings; it is unfortunate that it is not mole frequently used when referring to the occurrence of the mineral on an economic scale. Ores "Tinstone" js a very convenient old English term deserving a more frequent use. Tinstone is a dioxide of tin, or stannic oxide. When chemically Pure, as in the very rare transparent variety, it has a metallic content of 78.6 per cent tin. Frequently, however, the crystals and grains contain appreciable amounts of impurities, chiefly iron and tantalum. The impurities here referred to are those actually in the mineral itself. Tinstone usually has a deep brown or black color with an adamantine luster. Several other colored varieties are known, among them red ruby tin, yellow rosin tin, and yellow wax tin. the names jn each case being descriptive of the mineral&apos;s appearance. Ainalite is a variety of cassiterite con-taining almost g per cent of tantalum pentoxide. Sparable tin, tooth tin, and needle tin, as a result of their acute dite-tragonal pyramidal crystalline form, re-ceive their names from their crystallo-graphic appearance. Wood tin is a compact variety of cassiterite composed of radiating fibers resembling dry wood. Toad&apos;s-eye tin is a similar variety on a smaller scale in which the fibers appear to resemble the eye of a toad. Stream tin is water-worn tin-stone. Float tin is sometimes employed to describe the cassiterite occurring in soil derived from the weathered surface of a mineralized area. Stannite is an ore of tin of lesser impor-tance than cassiterite. It is a sulphide of tin, copper, and iron, sometimes known as tin pyrites or bell-metal ore. Its chemical com-position is sometimes expressed by the for-mula Cu,S.FeS.SnSz with zinc usually present in varying quantities. The tin con-tent varies from 22 to 27 per cent and there is about 29 per cent of copper, 13 per cent of iron, and 30 Per cent of sulphur.

Jan 1, 1944

By Reno H. Sales, Charles Meyer

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte&apos;s Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.&apos; Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature&apos;s deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company&apos;s answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world&apos;s largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the scricitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte&apos;s Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.&apos; Introduction From the economic viewpoint it is highly desirable that much effort be expended for the purpose of increasing our knowledge of ores and their origin. It has been the observation of the senior writer, many times expressed, that the mining companies have spent too little money in research on the geology of nature&apos;s deposits of copper, lead, and zinc, which we know to be of limited extent and which, when exhausted, must be replaced by new discoveries. Experience at Butte and elsewhere has forced the conclusion that observation and mapping in the field must be supplemented by laboratory work if we are to arrive at a reasonably correct understanding of the geology of ore bodies and their environments. It is only through the medium of such correct understanding of geology that we shall be able to accomplish the maximum toward aiding mine operations and at the same time provide a proper background for field examination work whether it be geological or geophysical. The Anaconda Copper Mining Company&apos;s answer to the need above expressed has been to equip a geological laboratory at Butte. The reason why Butte was selected is obvious, for situated there is one of the world&apos;s largest and geologically most interesting concentrations of copper and zinc. Furthermore, because of the great extent of underground workings both laterally and vertically, the opportunities for observation and study of ore occurrences probably are unequaled anywhere. The laboratory was established with five principal objectives in view. These were: 1. As an aid to Anaconda Company mine operations at Butte and elsewhere, this work to supplement that of the mine geologists. 2. To aid in acquiring as complete an understanding as possible of the behavior of Butte veins and ore bodies laterally and in depth.

Jan 1, 1949

By Walter C. Lawson

THE primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in&apos; the Morenci open pit. GENERAL MINING OPERATIONS Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months&apos; period (Fig I). Broken ore and waste, is loaded., into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high:. They are blasted- with churn drill holes, and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). PREPARATION OF PANEL GRADE In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many ties broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1947

By Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941, when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948.

Jan 1, 1949

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944

By Joseph Jensen

THE history of the normal oil field is supposed to show an oil graph stalting high in flush production, descending more or less steeply into the curve of settled production and dropping gradually to the vanishing point of economical operation. Together with this at somewhere in the early history of the field, there appears from a vanishing point a graph showing the production of water. During the period of settled production this graph rises higher and, toward the close, unless extensive work is done in the line of correction, rises far above the oil graph to where the cost of operation terminates profitable pumping. Fields that start out with a high relative content of water are generally very short lived. Fields that never develop a water problem are exceedingly rare.

Jan 1, 1930

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By J. B. NEALEY

MANY nonferrous smelting plants have recently adopted natural gas as fuel with resultant economies, both in cost and efficiency of utilization. Not only has this fuel been used for roasting, reduction, sintering, drossing, and smelting, but also for power. All of the three big smelters near Salt Lake City, Utah, have been changed over from coal and oil firing to gas. Among these is the plant of the International Smelting Co., Tooele, an Anaconda subsidiary, smelters of both copper and lead ores. In the roasting division at Tooele are 32 MacDougall six-hearth roasters, each 16 ft. in diameter and 19 ft. high. Two gas burners are installed on each furnace. These burners are of the single-valve, automatic gas-air proportioning type using high-pressure gas at 10 lb.

Jan 1, 1933