Search Documents

By Howard R. Keil

Reactor at Carlton mill successfully calcines pyrite-telluride flotation concentrate for cyanidation. CARLTON mill in the Cripple Creek district, 45 miles southwest of Colorado Springs, Colo., has been in operation for approximately three years, treating the custom sulpho-telluride ores formerly handled by the Golden Cycle mill in Colorado Springs. At the new mill the pyrite-telluride flotation concentrates have been roasted, prior to cyani-dation, in a Dorrco FluoSolids reactor, which has proved capable of yielding calcine readily amenable to cyanidation. Incoming ores are crushed at Carlton to % in. and sampled in 30 to 75-ton lots before the individual lots are mixed in the fine ore bin. The composite ore then goes to the grinding circuit. Classifier overflow from the grinding circuit is treated by flotation to produce a concentrate containing approximately 85 pct of the values in 5 pct of the weight. The flotation concentrate goes to the FluoSolids reactor prior to cyanidation. Cyanide solution values are recovered by zinc dust precipitation. Flotation tailings are thickened and cyanided, the values from this part of the circuit being recovered from solution by activated carbon. Gold values in the flotation concentrates consist of a small amount of finely divided metallic gold; the tellurides, sylvanite and calaverite; and gold very intimately associated with the pyrite. The metallic gold and a part of the telluride values can be extracted from the concentrates by cyaniding without roasting. However, extraction on the tellurides by this method is not satisfactory, and the pyrite values are so intimately associated with the pyrite that very fine grinding and cyanidation for a prolonged period under ideal laboratory conditions does not yield good recovery. Upon roasting, the tellurides are oxidized to very finely divided metallic gold which is readily soluble in cyanide. The pyrite is oxidized mainly to a porous iron oxide which allows cyanide solution to penetrate to gold particles and take them into solution. Feeding the Reactor Flotation concentrates move by gravity to a thickener. Thickener underflow is discharged at approximately 60 pct solids, by means of a diaphragm pump, into a storage and blending agitator. From here the concentrates are pumped to a disc filter. The filter cake, at 84 to 88 pct solids, drops directly into a repulper where it is repulped into a slurry of 78 to 80 pct solids. The repulped filter cake flows into a 6x6-ft slurry agitator from which it is fed directly into the reactor by the Moyno pump. The Moyno pump has eliminated a large number of difficulties that were first encountered in feeding a wet concentrate to the reactor. On the original installation in Canada a screw feeder was used to introduce the filter cake directly into the reactor. Since the reactor is under a slight positive pressure it was necessary to have a suitable seal to prevent gas escaping from the reactor at this point. When the concentrates produced in flotation were coarse or granular they could be readily fed to the reactor but when fine-textured, clayey concentrates were produced a great deal of trouble was encountered.

Jan 1, 1955

By N. D. Shutler

This paper describes a numerical mathematical model of the steamflood process that depends on fewer restrictive assumptions than models previously reported. The solution, however, is obtained economically. Example calculations are presented that, on comparison with experimental results, tend to validate the model. Results that expose certain process mechanics are discussed. The model describes the simultaneous flow of three phases — oil, water and gas — in one dimension. It includes the effects of three-phase relative permeabilities, capillary pressure, and temperature- and pressure - dependent fluid properties. Interphase mass transfer of water-steam is allowed, but the oil is assumed nonvolatile and the hydrocarbon gas insoluble in the liquid phases. The model allows heat convection in one dimension and two-dimensional heat conduction in a vertical cross-section spanning the oil sand and adjacent strata. The hydrocarbon-steam gas composition is tracked, but the effect of gas composition on water-steam phase behavior is neglected. The model is solved numerically in three separate stages. The three-phase mass balances are solved simultaneously using Newtonian iteration on nonlinearities occurring in the accumulation terms. The energy balance is solved separately by noniterative application of the alternating-direction implicit procedure. Separate solution of the composition balance is accomplished by straightforward solution of the finite difference equations. The method of effecting nonsimultaneous, stable solution of the mass and energy balances is the key to the success of the model. INTRODUCTION Mathematical tools as well as laboratory and field experiments are necessary to help us understand the complex steamflood process. A mathematical model can expose process mechanics and show the relative importance of process variables, but this ability is often limited by restrictive assumptions. Most known models of steam processes,l-5 with the exception of the model of Gottfried,6 are "simplified" in that they involve analytic approximations and require many restrictive assumptions. The primary utility of these methods lies in the routine use as an aid in engineering design. By contrast, the comprehensive model presented here is numerical and requires far fewer restrictive assumptions. It finds its primary utility as a research tool. It serves as an aid in understanding the nature of the process, in interpreting laboratory experiments and in evaluating and developing simpler mathematical models for engineering design. The major reason why previously presented models have been confined to the "simplified" class is evidenced by the one published exception. In 1965, Gottfried6 presented a numerical model for the combustion process of which the steam process is a subset. The result is a comprehensive tool (though it neglects capillarity and two-dimensional heat conduction) that is troubled with convergence problems and that requires 2 to 3 hours of IBM 7094 time to complete a calculation. Though our present model does not simulate combustion, it does consider capillarity and two-dimensional heat conduction and it overcomes the convergence and computer-time problems. MATHEMATICAL DESCRIPTION OF STEAMFLOODING FLUID FLOW The equations employed to describe three-phase fluid flow are of a familiar form. Darcy's. law provides expressions for the velocities of the three phases (oil, water and gas), which, when combined with oil, water and gas mass balances, give the partial differential equations governing flow of the

Jan 1, 1970

By AIME AIME

Gentlemen, we have ten questions on our list and a number of us here probably have other questions to ask. Therefore, we arc going to allocate the time to these different questions so that we will try to be finished by 4:30; from then until 5 o'clock, if any of you have any questions on subjects not related, you will be free to ask them. Mr. Morton and I have changed the order of the questions. Instead of what is now first, we have put No. 3 first, progress on basic-roof construction, inasmuch as we feel that it is quite important. At this time, H. S. Robertson, of Harbison-Walker, is going to give you a short talk, with slides, on what has been done to date on this subject.

Jan 1, 1940

By P. P. Gregory

NATURAL petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the ``pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the con-trolled methods of production and drilling, a portion of this gas is pro-duced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a-given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grog rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures were increasing.

Jan 1, 1938

By P. Somasundaran, Y. H. C. Wang

A detailed study of carrier flotation of kaolin clay using calcite showed the major beneficiation mechanism to be enhanced aggregation between anatase and calcite under intense agitation conditions. To develop an understanding of this selective aggregation, surface charge characteristics of kaolinite, anatase, and calcite were studied under simulated flotation conditions. Zeta potential of all these minerals tended towards a constant negative value in oleate solutions under certain conditions possibly due to adsorption or precipitation of oleate on them. However, whereas the zeta potential of anatase in the oleate solutions was not influenced by the agitation level, that of kaolinite was found to be strongly dependent on the agitation intensity. The effect of oleate on zeta potential of kaolinite was reduced by an increase in agitation intensity. It is suggested that oleate is much more firmly bound to the surface of the anatase and that this preferential attachment is responsible for the enhanced selective aggregation of the anatase with calcite. Agitation level plays a major role in carrier flotation since intense agitation is considered to enhance both the chemisorption of oleate on anatase and preferential detachment of calcium oleate precipitate from the kaolinite surface, all of this producing a large difference in the surface Properties of anatase and kaolinite, and hence in their tendency to aggregate with calcite.

Jan 1, 1983

By G. L. Oldright

THE economic manufacture of sulfuric acid by the ordinary chamber process usually involves production on a large scale and a plant that is costly to construct. The nature of sulfuric acid makes it costly to transport any great distance. For these reasons, the metallurgist has not found it feasible, at times, to beneficiate ores amenable to leaching, and a. need exists for a local process that will produce acid cheaply on a small or large scale. To leach ores containing residual sulfides, an oxidizer, such as ferric sulfate, is needed in solution. Precipitation with scrap iron is one of the cheapest methods of removing some metals from solution, giving a plant of low first cost and supplying a source of cheap ferrous sulfate. The other ingredient needed for the process is SO2 roaster gas; the addition of which, as, described below, will give both ferric sulfate and sulfuric acid. Where roaster gas is a waste or obnoxious, product, the expense. for materials is still further lessened. The use of ferric sulfate and sulfuric acid as a solvent lends itself, well to the utilization of scrap iron as a precipitant, and the stages of the process fit in well together as an economic whole.

Jan 8, 1925

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983

By David Cornell, D. L. Katz

Procedures for computing turbulent flow of gas in steady state near the well bore and a graphical method for predicting unsteady state laminar flow at distances from the well have been combined to compute pressure gradients in gas reservoirs. Methods are discussed for predicting single and multiple transients at constant flow rate in an infinite reservoir, predicting constant How rate. in a finite reservoir, reproducing and interpreting back pressure test data, and prediction of the behavior of a closed-in gas well. An example of the graphical method is given for a single transient and the results are compared to a published analytical solution. A typical calculation of the pressure gradient in a reservoir and the production of gas is made .starting with data from a hack pressure test. INTRODUCTION The calculation of pressure gradients throughouse a ga-reservoir at any point in its production history is a complex problem involving turbulent flow near the well bore and unsteady state flow of the gas from the reservoir. The problem is complicated further by the variety of boundary conditions that may be imposed upon the flow. Such boundary conditions include finite or infinite reservoirs. constant or variable rates of production, constant or varying bottom hole pressures, complex initial pressure distributions throughout the reservoir, and pressure maintenance through cycling. In addition to these problems there are the practical difficulties associated with natural gas reservoir analysis These might include: (1) variation. in the permeability and porosity throughout the formation. (2) variations in the thickness of the formation, (3) communication of the producing formation with other producing zones. (4) radial variations in permeability due to influx of drilling fluid. acidizing. or the buildup of liquid in the formation around the well, (5) partial penetration of the producing zone. (6) water flood, and many others. These problems will be considered eventually. In the mean- time, it is necessary to present methods of handling the case of radial flow through a homogeneous, regular, producing stratum to a single well uncomplicated by other factors. The idealized case of steady state, radial flow from a natural gas reservoir was studied by Elenbaas and Katz5 and by Mac-Koberts.' An analysis of the unsteady flow of gases through porous media has been made by Aronofsky and Jenkins' for the one dimensional laminar case with the boundary conditions of constant downstream pressure and uniform initial pressure. Solutions for the partial differential equation for unsteady state radial flow of liquids through porous media have been given by Van Everdingen and Hurst" for the constant bottom hole pressure and constant production rate cases for laminar flow in a reservoir initially at a constant pressure. The analogous heat transfer equation has been treated by Perry and Berggren9 for the case of quenching a cylindrical hole in an infinite medium to a constant temperature. The back pressure curve, which involves the variation of the bottom hole pressure as it is determined by the behavior of the reservoir as a whole. has been studied by Rawlins and Schellhardt,10 Binck-lev,' Baumel and Breitung,' and others. No complete. adequate treatment has been given for the unsteady state, radial flow of gases into a cylindrical hole from a porous medium with or without the presence of turbulent flow and for any set of boundary conditions. If one relies only on analytical solutions of the basic equations, a new solution must be obtained for each new boundary condition. Furthermore, the complexity of the mathematical expressions for boundary conditions other than the very simple cases limits the use of analytical solutions. Graphical methods exist, however. that are general in nature, accurate, and readily employed. The analysis of steady and unsteady, laminar and turbulent, radial flow for various boundary conditions with application to specific natural gas well problems by means of graphical procedures forms the content of this paper. STEADY STATE RADIAL FLOW EQUATION FOR LAMINAR AND TURBULENT FLOW A steady state radial flow equation for laminar and turbulent flow through unconsolidated sands has been given by Muskat as discussion of the work by Elenbaas and Katz.5 This equation is based on the properties of unconsolidated

Jan 1, 1953

By S. Y. Han

INTRODUCTION More than 97% of the total uranium production of the United States comes from sedimentary deposits (1). These sandstone deposits were formed by reduction of migrating uranium-bearing solutions from volcanic silicate rock sources. Such deposits occur in two major forms, either as relatively flat, lens-like deposits or as crescent- shaped roll front deposits. The lens-like deposits are found as discrete masses enclosed in reduced sandstone which is generally surrounded by oxidized sandstone. The roll front deposits are found along crescent-shaped interfaces between reduced and oxidized sands tone (2). In-situ mining of selected sedimentary deposits has proven to be a viable method of extraction and competitive with conventional mining for relatively deep low-grade ores (2). In in-situ leaching, uranium is recovered by drilling injection and collection wells in the ore body, pumping a suitable lixiviant to dissolve the mineral, extracting uranium from the pregnant solution by ion exchange, and finally regenerating and recycling the lixiviant. Even though there is increasing interest and practice in developing the in-situ technique for obtaining uranium values from deeper, lower-grade reserves, there is a lack of knowledge of the basic leaching kinetics and combined transport processes. In-situ leaching operations, in general, appear attractive for the following three general types of deposits (2): (1) low-grade surface dumps or deposits which lie above the natural water table,

Jan 1, 1983

Diffusion in Solid Metals. BY ROBERT F MEHL (Institute of Metals Division Lecture Tech Pub 726 in Metals Tech, Aug , also Trans, vol 122 22,500 words ) Diffusion in solid metals constitutes one of the important fundamental phenomena in metallurgical behavior Apart from its obvious importance in processes such as chromizing, carburizing, nitriding and calorizing, it plays an important part in the processes of homogenization, age-hardening, and transformations in steel, its scientific importance is no less great Diffusion may occur within a grain, along a grain boundary, or upon a surface, though the exact and even the relative values of these separate processes are known for only a very few cases The requirement of solid solution formation presents the possibility of identifying solid solution phases by a study of diffusion layers Some distortion accompanies diffusion, leading to little¬ understood grain-size changes Distortion assists diffusion though usually it dis¬appears before diffusion has become extensive In a binary system the rate of diffusion is the more rapid in the lower melting metal Many of the published data are too qualitative to permit sound scientific conclusions Age-hardening data may be treated as diffusion data and rates of reaction in steel could profitably be studied from this point of view Studies on diffusion are of great importance to the develop-

Jan 1, 1937

By W. C. Schroeder

PRACTICAL experience has shown that at elevated temperatures solu-tions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2,3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solu-tion may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years', an understanding of its mecha-

Jan 1, 1936

By Kermit Allen

Historically, major natural gas transmission companies have been faced with the problem of meeting peak demands when the source of natural gas is located hundreds of miles away from the marketing area. Transcontinental Gas Pipe Line Corp.'s position was further complicated when offshore gas supply wells were shut-in during hurricane alerts. Transco's solution to this problem was the construction of salt storage wells adjacent to their pipeline near Eminence, Miss. Storage caverns were constructed using conventional solution mining methods. Two 13 3/8-in.-diam cased wells were completed and a 1,000,000-bbl cavern was leached at an interval of 5700 to 6700 ft at the base of each well. The two caverns have a usable storage volume of 2.0 billion cu f t and each well has a deliverability rate of 375 million standard cfd. The caverns are unique in that brine is not used for product displacement-all brine has been removed from the caverns. Natural gas is stored at a maximum pressure of 4000 psia. During withdrawal the cavern pressure drops to a minimum of 1225 Asia-the volume of gas between these two pressures becomes "usuable or top gas." The Eminence storage terminal is located on the Eminence salt dome about 30 miles north of Hattiesburg, Miss. Construction began in July 1968 and was completed in October 1970.

Jan 1, 1972

By C. Y. Ang, C. Wert

Quench aging of supersaturated solid solutions of nitrogen in columbium takes place in reasonable times in the temperature range 300&apos; to 500°C. Changes in internal friction, hardness, and electrical resistivity are found to accompany this change. THERE is practically no detailed information in the literature concerning interstitial solid solutions in either columbium or tantalum. The fact that both of these metals are used extensively commercially in both pure and alloyed states makes studies of their properties of value. While the plan is to study both these metals and their alloys extensively, so far only a small number of measurements have been made. This paper presents data obtained in the initial investigations of columbium. The principal interstitial impurities of columbium are likely to be hydrogen, carbon, oxygen, and nitrogen. The first of these, hydrogen, is outside the scope of internal friction measurements at present and nothing quantitative is known about the initial hydrogen content of the specimens. However, it is believed that it is completely absent after the preliminary heat treatments are carried out. The carbon content of the original samples is low and can be reduced still further during sample preparation. Oxygen is normally present to some extent in columbium and can also be added or removed easily. Nitrogen is also normally present in small amounts and can also be controlled within limits. Since it is not possible yet to remove all the nitrogen from columbium and since it is possible to remove essentially all the oxygen and carbon, initial measurements were made on the alloy system nitrogen in columbium. In this sense then, the alloys are true binary alloys. Little is known about the effects of nitrogen on the physical and metallurgical properties of columbium, so it was necessary to perform some rather elementary measurements on the specimens. These measurements are described briefly in the next section and are discussed in detail in later sections. Scope of the Work That internal friction is associated with diffusion of nitrogen in columbium has been known for some time. It is similar in nature to that for carbon and nitrogen in a-iron. In these latter cases, the information obtained from internal friction has been useful metallurgically.&apos; and it is not too much to expect useful information from similar studies on columbium containing nitrogen. The technique of internal friction measurements is adequately described by Ke2 At a frequency of 1 cps the internal friction peak for nitrogen in columbium occurs at 300°C and that for oxygen at 160°C." So that all the measurements will be meaningful metallurgically, the internal friction has been calibrated by making a measurement of the damping at the two peaks and a measurement of oxygen and nitrogen content by chemical analysis. A comparison of the two gives the following calibration factor: To go from damping capacity expressed in terms of 1/Q to weight percent of oxygen and nitrogen in solid solution in columbium, multiply the peak values of internal friction by about 4 and 3 respectively." Data from which these factors were calculated are presented in Table I. The increase of electrical resistance of columbium caused by the addition of oxygen and nitrogen as interstitial impurities has been quantitatively determined. At room temperature the percentage increase is small for small additions of impurities (<0.1 wt pct); as the temperature is lowered it becomes an increasingly larger factor of the total resistance. An empirical relation has been established to express the resistivity at — 195°C in terms of weight percent of oxygen and nitrogen in solid solution. It is easy to make supersaturated solid solutions of nitrogen in columbium and to observe aging phenomena. The optimum aging temperature, as in the case for carbon and nitrogen in a-iron, occurs at the temperature for which the time necessary for a single place-change in diffusion is about 1 to 10 millisec. This means for nitrogen in columbium that significant property changes should take place for this alloy at about 400" to 500°C in reasonable time intervals. Results of such aging experiments are

Jan 1, 1954

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers&apos; have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.&apos; Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By J. B. Hiskey

The hydrometallurgical application of thiourea in processing precious metal ores and concentrates has reached the development stage. This paper reviews recent technical literature covering the process development of thiourea leaching. In addition, recent fundamental contributions are discussed. Most of the interest in thiourea leaching has involved treating high grade concentrates that have sufficient value to just the use of thiourea as a reagent. An important development in thiourea technology is the addition of SO2 to the leaching solution. This procedure effectively reduces the decomposition of thiourea and eliminates the problems of passive surface layers that limit the leaching efficiency. Results for the thiourea leaching of a bulk sulfide concentrate and a residue from the autoclave leaching of a smelter flue dust are also reported. As determined by a standard bottle roll cyanidation test, the bulk concentrate was extremely resistive to cyanide leaching yielding only 16% gold and 2% silver extraction in 24 hours. Leaching with a relatively concentrated thiourea solution (1MCS (NH2)2) resulted in 83% gold and 75% silver extraction in four hours. With the treated flue dust residue, gold extraction was about 60%. Gold and silver extraction with cyanide was sensitive to both cyanide concentration and oxidizing conditions. Cyanidation resulted in 59% gold extraction and 77% silver extraction in 24 hours.

Jan 1, 1985

By J. C. Cook

In solution-mining of underground salt and similar minerals, using drilled wells for access, it is desirable to monitor the lateral growth pattern of the resulting fluid-filled cavern. Therefore, a process of seismic surveying from the surface of the ground has been conceived in which the amplitudes of waves reflected from and transmitted through the soluble formation are measured. The large acoustic impedance contrast between solid and fluid should produce striking amplitude anomalies, especially if shear waves are employed, since thick fluid bodies are opaque to shear waves. Horizontally-polarized (SH) shear waves are best for preventing conversion to P waves at the numerous horizontal interfaces in the ground. Field tests to date have shown that a truck-mounted, half-ton hammer striking horizontally against the end of a trench produces usable SH-wave energy at lateral distances up to about 850 ft. Horizontally-directed explosive wave sources were effective to about 2000 ft. Conventional magnetic-tape recording and processing were used, but with the detecting geophones oriented to favor SH waves. An irregular solution cavity in bedded salt at 500-ft depth has apparently been located by SH-wave and SV-wave reflections. Further field work is planned to corroborate and extend this result. The Brine Cavity Research Group, an association of 11 chemical and salt producing companies, is supporting this work. Major deposits of salt in tabular beds lie beneath some 300,000 sq miles of land in the central and northeastern U.S. This salt is a basic source of soda ash and chlorine, and has been extracted as brine from drilled wells for about a century. During the past two decades, the U.S. solution-mining industry, following the lead of European operators, has greatly improved the extraction process through the application of engineering and science.&apos; In 1957, the Brine Cavity Research Group, an association of 11 chemical and salt producing companies, was formed. This group proceeded to attack certain common problems through the support of research. An outstanding problem has been that of determining the shape and location of the growing solution cavities in the underground salt, so that measures can be taken to maintain operating efficiency. The problem has been partially solved by the Dowel1 sonar mapping service, which employs a pulse-echo device lowered into the cavity through the well.2 However, the working range of this equipment is at present insufficient for large cavities, and echoes are not returned from highly sloping walls nor from behind such obstructions as rock debris. Therefore, an independent means of mapping the cavity, for example, from the surface without interfering with operation of the well, would be desirable. THEORY OF THE METHOD Seismic waves are the only physical agent known to be capable of sufficient resolution and penetration to define typical solution cavities from the surface of the ground. The geometry is unfavorable: cavity widths are generally less than half their depths below the surface; resolution and lateral location of boundaries and channels to within 50 ft at depths of 500 to 3000 ft is desirable. Conventional seismic surveying, as used for petroleum prospecting, is probably not the answer: isopach mapping, for example, is not thought accurate enough to define the cavity by the slight additional delay time it would introduce (of the order of 0.005 sec for a 50 ft-thick cavity in hard Paleozoic rocks). Refraction surveying has also been considered, but seismic specialists see little promise in it for this problem. In 1957, in correspondence with industry personnel, the writer suggested a seismic method based upon careful measurement of reflection amplitudes. As Table I illustrates, seismic reflection coefficients r for typical brine-rock interfaces are considerably higher than those for typical interfaces between different kinds of solid rock. This fact can be utilized in two ways, illustrated in Fig. 1: 1) If the cavity roof is reasonably flat (which it may sometimes be since the unsaturated top brine will be in contact with an insoluble rock stratum), extra-strong seismic reflections will be received from the salt stratum where the solid has been replaced by liquid.

Jan 1, 1964

By L. G. Austin

If S (x) is the specific rate of breakage of size x and B (x, y) (see Table 1 for Nomenclature) is the cumulative breakage distribution function, the Herbst Fuerstenau2 assumption is that Inserting this assumption into first-order grinding equations it has been shown" that there are then simple analytical solutions to the grinding equations, as shown in Table 2. In this context "plug flow" is defined as all material passing through the mill in the same length of time, the residence time t. The term "n fully-mixed" means that the mill has a residence time distribution" which can be treated as if the mill were n equal fully mixed sections in series. In addition it has been shown that the assumption of Eq. 1 also leads to simple analytical solutions for closed-circuit, steady-state grinding with an ideal classifier at the mill exit returning oversize to the mill feed. The solutions are also given in Table 2, with µ as the ideal classifier cut size, C the circulation ratio, and Q (x) the size distribution of the circuit product. The specific surface area of these size distributions is where the density-shape factor k. is assumed to be constant with size. In practice, most methods of size analysis or area [ ] measurement have a finite lower limit, so that the integration is really performed from xm, to xm, For a realistic degree of grinding the value of So is dominated by the fine sizes because of the 1/x factor. Consider batch grinding of a feed of size y to y + dy. The batch grinding solution given in Table 2 is then [ ] The fresh surface area produced is the area of the fines plus the area of the original material remaining minus the area of the original material, [ ] Little error is introduced by neglecting the last term on the right-hand side since at t = 0 it is zero, and when t is significant the first term dominates because of the fine sizes produced. In addition, the form of P (x, t) for [ ] realistic values of S (x) 2t ax° is such that the major fraction of fresh surface produced is contained within the bottom 10% of weight of broken material, that is, for sizes for which P(x, t) < 0.1 (providing y is not near x.,). Thus for surface area purposes Eq. 3 can be approximated by [ ] becomes providing again that the feed sizes are coarse relative to xmi. Then the fresh area production is and W is the mass in the mill. The rate of surface production is WK, and the specific surface is Kt. From Table 2, the specific energy is mt/W so surface production per unit energy is [ ] Surface produced per unit energy input = KW/m (8) where m is the energy input of the mill. Clearly, identical reasoning applies to open-cycle, plug-flow grinding, with t replacing t, and Eq. 8 is obtained again. Considering open-cycle, fully mixed grinding, similar reasoning gives P(x) - t S(x) for surface area purposes, and

Jan 1, 1974

By A. E. Back, S. F. Ravitz

When manganese ores are leached with sulphur dioxide, a large part of any zinc in the ore usually is extracted with the manganese.1 In the dithionate process,2,3 in which the manganese ore is leached with dilute sulphur dioxide gas and the manganese is subsequently precipitated by adding lime to the pregnant solution, the zinc is precipitated with the manganese. These facts suggested the possibility of applying the dithionate process to the recovery of zinc from oxidized ores or calcined sulphide concentrates. Accordingly, an investigation was begun, and preliminary tests were made on several ores and concentrates. The results were encouraging, but the need to devote available funds and personnel to other projects made it necessary to drop the work before the various factors involved in the process could be studied in detail. A brief mention of the process,4 however, elicited a number of inquiries, so that it appeared desirable to report the results of the preliminary work. The dithionate process as applied to zinc may be summarized briefly as follows: The ore or calcined concentrate is leached with dilute SO2 gas to dissolve the zinc, largely as zinc sulphate, in accordance with the following equation in which [ZnO] represents the "oxide zinc" in the ore or calcine: [ZnO] + SO2(g) + 1/2 O2 = Zn++SO4— [1] If, in the leaching step, the ore or calcine is suspended in calcium dithionate solution, the sulphate ion, as it is formed, is precipitated immediately as calcium sulphate, which is subsequently filtered off with the insoluble ore residue: Zn++SO4— + Ca++S2O6— = CaSO4(s) + Zn++S2O6- [2] An alternative procedure is to suspend the ore in water, filter off the insoluble ore residue after leaching, add calcium dithionate to the resulting zinc sulphate solution, and then filter off the calcium sulphate precipitate. In either event the zinc is obtained in the form of a pregnant solution of zinc dithionate, from which it can be precipitated as relatively pure zinc hydroxide by adding milk of lime: Zn++S2O6— + Ca(OH), = Zn(OH)2(s) + Ca++S2O6- [3] The zinc hydroxide precipitate is calcined to form the final zinc oxide product: Zn(OH)2 = ZnO(s) + H2O(g) [4] Theoretically the process is completely cyclic with respect to dithionate ion, the calcium dithionate required for reaction 2 being replaced by that formed in reaction 3. In practice, of course, small amounts of dithionate would be lost in the various filter cakes, depending on the economic washing limits. In the leaching step, however, some of the SO2 is oxidized to dithionale instead of sulphate, accord- ing to the following overall reaction: ZnO + 2SO2(g) + 1/2 O2(g) = Zn++S2O6-, [5] so that the dithionate losses are made up, at least in part. Ores and Concentrates Tested The analyses of the ores and concentrates tested are summarized in Table 1, which also includes the analyses of the calcines produced from the concentrates. The concentrates were roasted in a laboratory muffle furnace at the temperatures indicated until evolution of SO2 could no longer be detected; shallow clay dishes ordinarily were used; but calcines 2a and 2c were prepared in iron dishes, with the result that these two calcines were badly contaminated with iron scale. The "complex" concentrate, sample 1, consisted essentially of sphalerite grains containing inclusions of pyrite and other sulphide minerals too minute to be liberated by grinding within economic limits. In the " marmatitic" concentrate, sample 2, the iron was present largely as marmatite (that is, as iron sulphide in solid solution in zinc sulphide) rather than as pyrite inclusions. The zinc was present largely as the carbonate in the two "oxidized" ores, samples 3 and 4, and as the silicate in the "willemite" ore, sample 5. Leaching Tests The leaching cell was a 3-liter glass beaker placed in an electrically heated water bath manually controlled to maintain a temperature of 35°C in the leach slurry. The slurry was agitated by means of a flat paddle-type stirrer

Jan 1, 1950