Search Documents

By H. C. Babbitt

The Effect of Arsenic.—A question involving the temperature of precipitation of ammonium phospho-molybdate, which was brought to my attention some time ago, led to the following experiment :*

Jan 1, 1893

By Raymond L. Jones

With the inauguration of open-pit copper mining in Bagdad, Ariz., plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until spring 1961.

Jan 9, 1977

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20'24'25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M'1B|28'i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown' that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By Charles H. Jacoby

During the past three decades an ever increasing number of uses for underground storage space has been developed. In some instances, the value of the space created has been so great that the host rock has been wasted. The preferential use of salt to host underground cavities is based on numerous factors, the primary two being low extraction costs and low permeability. Both dry and solution mined cavities have been created for the storage of a variety of materials. As the demand for underground storage and disposal grows, so must our selectivity of the materials to be stored.

Jan 1, 1985

By G. W. Tower

THE YEAR 1931 was for most American copper producers one of restricted output but extremely low production cost.. When compared with 1929, the marked reductions in costs achieved in 1931, operating at rates in many instances a third to a half of capacity, can only be regarded as remarkable. In fact, the recent shut-down of several large operations suggests the probability that 1931 costs represent a bare minimum for many properties. Before discussing the 1931 results a few remarks on cost data are appropriate. The type of cost tabulation here presented was first published in 1929, (A. B. Parsons. E. & M. I. June 8, 1929), and has appeared each, succeeding year following in general the calculation method and company set-up of the original article. (. G. W. Tower, E. & III. L, July 8. 1930; S. D. Strauss, E. & M. J.; July 27, 1931). As far as possible the leading American copper companies are included. In considering these cost tabulations it must be borne in mind that the information from which they have been prepared is entirely contained in the annual report of each company; and that a multiplicity of interests and a condensed income statement for some of the larger companies, such as Cerro de Pasco and Kennecott, make the cost figure an arbitrary one depending upon sundry metal credits, metal products, miscellaneous income, etc. For Granby, Howe Sound. Magma, and Noranda, sundry metal credits are important. Furthermore Andes, Chile and Greene Cananea give costs only against copper sold. Although the individual costs here figured are by no means absolute they are computed by the same method each year and offer a basis of annual comparison; and with attention to footnotes the premises on which the costs are based may be easily followed.

Jan 1, 1932

By K. G. Davis, P. Fryzuk

A study has been made of the effect of undercooling on the grain structure and solute distribution in small ingots of pure bismuth and of a 100 ppm Ag in bismuth alloy. Autoradiographic evidence shows that in undercooled melts a network of dendrites is formed throughout the melt immediately after nu-cleation. At large undercoolings the dendrites are very thin and closely spaced. The origin of the observed grain morphology can be explained on the basis of information about the mode of solidification revealed by the impurity substructure. WHILE a great number of studies of nucleation in undercooled molten metals have been made, comparatively little attention has been given to the mode of solidification from melts with large undercool- ings. Colligan and Bayles1 and Walker2 have measured the rate of advance of the solid-liquid interface in undercooled nickel melts, but the morphology of the solidifying material remained a matter of speculation. Fehling and Scheil3 have described the grain structure in ingots formed from undercooled melts of nickel, palladium, and copper, and a series of Ni-Cu and Ni-Pd alloys. At small undercoolings, equiaxed structures are observed, the grain diameter tending to increase as the temperature of nucleation is lowered. At greater undercoolings, a columnar structure is developed, while with still further undercooling there is a smaller grain size incorporating rather coarse subgrains. All-bright and Colligan4 examined the grain structure shown by ingots solidified from melts of nickel and of Ni-Ag alloy at an undercooling of 105°C, and concluded that considerable grain growth had taken place after solidification. The object of the present work is to correlate the mode of solidification from undercooled melts with both the grain structure and impurity segregation, using tracers to examine the latter.

Jan 1, 1965

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

A. U. Seybolt (General Electric Research Laboratory)—The authors should be commended for adding some important information to our knowledge of the solubility of interstitial elements in metals. It is becoming increasingly evident that the effect of even traces of such elements have very far-reaching effects upon the mechanical properties of the body centered cubic metals. Those who have worked in this area know that the accurate determination of the small solid solubility limits in systems of the type reported by the authors is a quite difficult task, and it is therefore not surprising that frequently the results of different workers are not in agreement. It is instructive, and usually helpful, to plot the solubility results on log weight or atomic percent -1/T coordinates to find out if a straight line is obtained. A straight line is expected because in systems displaying solubilities of the order of 1 to 3 at. pet or less, Henry's law is usually obeyed—or at least well enough obeyed so that the deviation from linearity is not very appreciable. If Henry's law is obeyed, one canthen use the Van't Hoff Equation in the form In N = ?H/RT + C, where N is mole fraction, at. pet, or wt pet for small values, and AH is the partial molal heat of solution of the solute. R and T have the usual significance, and C is an integration constant. If one plots the reported nitrogen solubility values as indicated above, the three points fall reasonably well on a straight line. The oxygen values for the two upper temperatures fall very closely to the nitrogen values as shown in the authors' Fig. 15. However, the value at 500°C departs widely from the straight line established by the data at 1500" and 1000°C. It is, of course, true that one cannot place too much emphasis on the significance of a line established by only three points, but in the absence of reasons for anticipating deviations, data exhibiting wide departures from linearity should at least be examined closely. Fig. 16 shows the log at. pct -1/T plots for the authors Ta-O and Ta-Ndata including a solid circle point at 500°C and 1.8 at. pet for Ta-O, which is simply extrapolated from the two higher temperature points. In addition, the data of R. P. Elliott9 for Nb-O are shown. These points were picked off his curve and are not very exact, but as can be seen they line up well on a straight line. It is interesting, and probably significant, that the slope of Elliott's results is not far from those of Vaughn, et al. This is probably to be expected because one would anticipate that the partial molal heats of solution of oxyten in these two very similar metals should be not too far apart. AH for Ta-O is about -1900 cal per mol, while for Nb-O it is near -2300 cal per mol. Hence, this lends some support to the thesis that the point at 500°C for Ta-O is much too high. The data of Gebhardt and Preisedanz10 are also plotted, and it is seen that their data while lying on a linear plot, have an appreciably steeper slope. The possible reasons for this will not be discussed here except to point out that their pressure-composition data show anomalies which suggest that they may have been dealing with a different equilibrium from that being discussed. There is another consideration which would also suggest that the solubility at 500°C is lower than shown. The solubility values were obtained by the classic method of first establishing a lattice parameter-composition curve. This the authors did, and there is probably little doubt that it is quite accurate. Such a plot is generally almost error-free because it has a self-correcting feature in that any deviation from linearity makes a data point immediately suspect, and subject to confirmation. Unfortunately, this is not true with respect to the actual solubility values. These are obtained ordinarily by taking an alloy containing more solute than is soluble at some temperature and then thermally

Jan 1, 1962

By E. W. Pehrson, J. W. Furness

NONMETALLIC MINERALS, exclusive of fuels, may be divided into three groups: Building materials, fertilizer minerals, and miscellaneous minerals. Building materials, such as sand, gravel, slone, lime, and the ingredients of cement and clay products, occur widely in nature and are thus available near consuming centers at relatively low prices. Cost of transportation over great distances deters any' substantial movement in world trade. On the other hand, fertilizer minerals, such as phosphate rock, potash, nitrates, sulfur, and pyrite, and the miscellaneous nonmetallic minerals, such as long-fiber asbestos, mica, graphite, fluorspar, and china clay, do not have such widespread occurrence and consequently contribute the major part of the world's commerce in such minerals. The U. S. Bureau of Mines has prepared charts showing the inter-

Jan 1, 1936

By John J. Porter

UNUSUAL problems have arisen at certain iron blast-furnaces in Virginia through the fact that the ore-supplies, derived from the Oriskany formation, contain from a trace up to 1 per cent. of zinc oxide. Since the technical literature bearing on this subject is very scant, the following notes, based on personal experience, will probably be of value to those of our members who are interested in iron blast-furnace practice. The course of zinc through the blast furnace is readily traced. Entering the throat as zinc oxide, finely disseminated through the ore, it descends unchanged to the fusion-zone, since a temperature of 1,000° C. or more is required for its reduction. At the fusion-zone, the zinc oxide is reduced by solid carbon to metallic zinc, which is set free as vapor and rises with the ascending gases to the cooler zones of the furnace. In cooling through the range of temperature from 1,000° to 500° C. the zinc is re-oxidized according to the reaction Zn + CO2 = ZnO + CO, and the resulting zinc oxide, being in a very fine state of division, is readily carried along by the ascending gases. Portions, however, deposit on the descending stock and are carried down, again to pass through the same cycle of changes. Still other portions deposit on the lining of the stack, and gradually form hard masses of "cadmia." Of the remainder of the zinc oxide, the greater part passes out of the furnace, and is either deposited in the down-comer, dust-trap, stoves, boilers and flues, or passes through the chimney into the atmosphere. A small portion escapes reduction and enters the slag as zinc oxide, while still another portion is absorbed into the lining of the furnace.

Sep 1, 1907

By Oliver Bowles

ROCK is no doubt the most abundant of all material things because the planet on which we live is made of it. All animal and vegetable organisms and the multitude of natural and manufactured products that occupy a comparatively insignificant film on the outer surface of the planet are derived from rock. Processes of Nature acting for untold centuries have transformed rock into soil, making possible the development of vegetable and annual life; and rocks have supplied the numerous raw materials, metallic and nonmetallic, wherewith the innumerable appurtenances of a complex civilization have been fabricated. As time goes on we live with increasing speed and with enlarged desires. Time and space are shortened by man's ingenuity, and products for human use must be manufactured with greater and greater celerity. It was inevitable that Nature's slow processes of rock alteration should fail to keep pace with human demands and that the variety of natural products should fall far short of the requirements of an industrial age. Man therefore supplemented these processes by attacking rock in its native bed amid using it to supply needs not otherwise satisfied.

Jan 1, 1934

By Strathmore R. B. Cooke

On the basis of experiments conducted on quartz using a bubble pick-up method, it was shown in an earlier paper1 that this mineral will preferentially adsorb hydrogen, calcium, or sodium ions, depending on the relative concentrations of those ions in the solution in which the quartz is immersed. For quartz particles ranging in size from 0.2 to 1 mm, it was demonstrated that the concentration of calcium in solution (assumed present as ions) necessary to completely activate quartz for flotation is given by the expression: Ca++ = [H+] X 106 + [Na+] X 10-3 In this expression, ionic concentrations are in mols per liter. It was further shown that the pick-up method is apparently more sensitive to changes in reagent concentration than the standard captive-bubble method, and that induction times are apparently much reduced. Since completing these earlier tests, a new type of cell has been constructed; this is shown in Fig 1 and 2. In Fig 1, A is a ground joint, B is a central tube reaching to within a few millimeters of the bottom of the cell, and C is a stopper which may be removed for reagent addition, and serves the further purpose of excluding carbon dioxide from the air during the test. The entire cell is constructed of Pyrex glass, and does not give the trouble experienced with the earlier cell, in which activating ions were released from the glass at high pH values. The only critical factor in the construction of the cell is the clearance between the central tube and the bottom of the cell. This clearance should be sufficiently small that the bubble can be pressed directly on the mineral grains lying on the bottom of the cell. In the pick-up tests to be described in this paper, the reagents used were all of C. P. grade, except the sodium oleate, which was Merck's "neutral powder." The quartz employed was water-clear vein quartz, sized on screens, cleaned with both hydrochloric acid and sodium hydroxide, and given a thorough final washing with distilled water. Experimental procedures were the same as described in the earlier paper. EFFECT OF SIZE OF QUARTZ ON PICK-UP To ascertain the effect of particle size on the adsorption of calcium ions, the quartz was sized from minus 14 plus 20 mesh through the intervening screen sizes to minus 270 mesh plus 400 mesh. Each size was thoroughly cleaned, and then tested in the cell at different calcium chloride and sodium hydroxide concentrations, and at a constant sodium oleate concentration of 20 mg per liter. All particles, within the size range given, exhibited complete pick-up within the curve expressed by the equation above. This presumably means, when the conditions imposed by the equation are satisfied, that this maximum is independent of particle size. However, it was found that the range through which partial particle pick-up occurred progressively broadened as particle size decreased. This is shown in Fig 3, in which curves B, C, and D show the limits at which pick-up just commences (as the pH is increased) for particles of minus 14 plus 28 mesh, minus 65 plus 100 mesh, and minus 270 plus 400 mesh size, respectively. These results indicate that for satisfactory activation, at any given pH, a lower calcium ion concentration is required for fine particles than for coarse particles. EFFECT OF HIGH ALKALINITY ON PICK-UP At calcium concentrations of between 1 and 10 mg per liter, and at high alka-linities, it was noticed that pick-up ceased as soon as calcium hydroxide commenced to precipitate. This effect was investigated at other calcium concentrations, with the same results. Solutions of calcium chloride, containing 105, 104, l03, and l02 mg of calcium per liter were made alkaline with sodium hydroxide until calcium hydroxide just started to precipitate, according to the following equation: CaCl² + NaOH -+ Ca(OH)2 + 2NaCl The beginning of precipitation was taken as that point at which either a faint opalescence appeared in the solution, or a Tyndall cone became ap-

Jan 1, 1950

A. R. Ledoux,New York City: The so-called combination method " is generally used in assaying bar copper for silver. It has been modified from time to time. Briefly outlined

Jan 1, 1901

By DONALD H. McLAUGHLlN

Few factors have had more influence in maintaining the strength and stability of the United States than our persistent habit of providing .checks and balances to the dynamic powers of free enterprise on the one hand and to the controls and guidance exercised by the State on the other. .Indeed, it is this same concern for matching forces against each other that has given our republic its ability -to preserve a democratic basis of life for its citizens, and yet maintain a ,government that is able to protect the rights of all and to resist and minimize the danger of excessive concentration of authority. Our current efforts to clarify the nation's mineral policies and to define more clearly the role that the governmental agencies should play in conjunction with the functions of private -enterprise again reveal the desirability and advantages of maintaining our traditional controls. At times, the equilibrium has been temporarily disturbed by too great enthusiasm for one or the other of these basic concepts. Sooner or later, however, the balance has been restored by the healthy opposition that is always created by excesses of one sort. At the current stage in our history, the swing toward undue enlargement of the powers of the State seems to have gone dangerously far and we would be untrue 'to our traditional behavior if the group that must demonstrate the virtues of free enterprise did not rally to its support with the utmost earnestness.

Jan 1, 1949

ION exchange is one of hydrometallurgy's new tools, new in application, vet old in principle. Cation exchange between solution and a solid exchanger has been known for more than a century, but ion exchange is still in its infancy for metallurgical use. Still hampered by cost of media, it is faced with much development of actual physical handling. Growing consumption of the rarer metals and need to treat leaner ores are pushing extractive methods ahead. Public concern with stream pollution, or legal requirements, are forcing a clean-up of waste discharge. Industries are finding it vital to make some recovery from heretofore waste material to help pay costs of discharge treatment.

Jan 5, 1953

By Radoslav Despotovic

The developed radiometric method of particle system analysis has been applied to investigate the bulk properties of particles precipitated from solutions. The nature and principles of the method applied are described briefly, and some possible models in the field of fine colloid particles precipitation discussed. Changes in radionuclide distribution were followed during the solid phase formation and the data were used to calculate changes in bulk composition of colloid precipitates. The radiometric data show interesting phenomena closely connected with the characteristic of bulk particles. The measured radiometric data are highly reproducible, the applied methods have proved to be sensitive, and the developed techniques have been tested by various standard procedures.

Jan 1, 1980

US 4,183,794 - Electrowinning zinc from a zinc sulfate solution produced by leaching zinc ore with sulfuric acid. The leach liquor is subjected to electrolysis in a first cell having an insoluble anode to deposit primary zinc on the common electrode. The coated electrode is transferred to a second cell having an alkaline electrolyte, and electrolysis is effected in the second cell to transfer zinc from the common electrode to the second cell cathode in a spongelike form which is readily stripped. R.H.C.L. Ross. Jan 15, 1980. 10 pp. (204-119). Filed: 12-22-77 (863,190). Same: Canadian 1,051,820, dated Apr. 3, 1979.

Jan 1, 1982

By Hans Lundberg, Basil T. Wilson, H. Steuart Scott

FOR the benefit of those readers who may not be in close touch with present practices in the geophysical prospecting for ore, brief reference will fiat be made to the advantages and shortcomings of the methods to be discussed. Magnetic and electric methods are generally accepted as the most useful for ore prospecting. By magnetic methods, magnetic intensities that are not normal may be recorded and outlined. From these can he located concentrations of such highly magnetic minerals as magnetite or pyrrhotite, which sometimes occur in such large masses that they are of economic value in themselves. More often. however, these magnetic min¬erals are associated with others, such as copper, zinc, lead, gold, and silver, which, if existing in sufficient concentration and quantity, may constitute valuable ore bodies. It is therefore only when pyrrhotite and magnetite are present in these bodies that the magnetic method can be used to indicate their presence.

Jan 1, 1945

By B. L. Seegmiller

Horizontally stratified lithologies of certain open pit or strip mines create unique stability problems for mine operations. Such problems may result when specific lithologies, such as sandstone and shale, exist in final or long-term slopes. Slope instabilities may occur when a sandstone unit directly overlies a shale unit and ground water drains into the mine along the lithologic contact. In essence, the ground water erodes the underlying shales and undercuts the sandstone. Large sandstone blocks fail in a toppling mode and cause safety and cleanup problems. Use of rock reinforcement including chain link fencing, roof bolt mats, rock bolts, rock anchors, and shotcrete offers a possible solution to the problem.

Jan 1, 1985

By K. D. Hester, A. C. Anderson

The Elliot Lake uranium deposits are contained in a pebble conglomerate which is similar throughout the basin. This paper compares the solid-liquid separation circuits of two nominal 3000 T/d acid leach uranium concentrates treating Elliot Lake ore. One concentrator employed rotary vacuum drum filtration for solids removal and washing, the .other used counter current decantation in torque arm thickeners. Capital and operating costs, operation and maintenance, and metallurgical performance of the two solution recovery methods are compared and contrasted. A recent development, removal of the sand fraction ahead of C.C.D. and separate sand washing in hydraulic cyclones, is also discussed.

Jan 1, 1973

By Charles Catlett

THE rapid development of the Portland-cement industry implies that the country is being very carefully searched for material suitable for its manufacture. Such material can be found at a great many places ; but deposits thoroughly satisfactory in chemical composition, and at the same time meeting all the other requirements connected with the economic production and profitable marketing of the product, are exceedingly few, if I may judge from the investigations which I have had to make in a number of States. The raw mixture which by its clinking and grinding forms Portland cement contains approximately 75 per cent. of carbonate of lime. This is found in nature as limestone or marl. The natural rock commonly carries either more than the required percentage of carbonate of lime (in which case it has to be reduced by suitable admixture of clayey ingredients) or less-in which case purer lime carbonate has to be added. The controlling ingredient, therefore, is carbonate of lime, or limestone of the right composition. Among the most serious difficulties is that of finding limestones low enough in magnesia to meet the exacting requirements of certain specifications. All engineers recognize that there is a limit beyond which it is not safe to let the magnesia go; but within that limit there is considerable difference of opinion. Until that difference is finally settled, no one would be willing to invest the large sum of money necessary for a Portland-cement plant, if it were not certain that the usual requirements in this particular could be satisfied. The usual limit in well-established specifications is 5 per cent. of magnesium oxide in the finished cement, but many specifications limit the amount to 3 per cent. These figures

Jan 9, 1907