Search Documents

By Frederic Benard

THE treatment of Balbach-Thum slimes at Copper Cliff by the Ontario Refining Co, is of interest because it differs considerably from methods usually employed for the recovery of fine gold from parting-plant slimes. Owing to the comparatively high percentages of palladium and platinum, wet methods are used to remove the greater proportion of these metals before electrolytic refining in the Wohlwill cells. THE PLANT The platinum-metals department, Wohlwill room, and gold-melting room extend along the north side of the silver refinery and are separated from the parting plant by a glass partition (Figs. 1 and 2). The platinum-metals department resembles a laboratory built on a large scale, with the various pieces of equipment laid out on terraces to facilitate handling. . Because of the corrosive nature of the solutions, chemical stoneware is used throughout. Elevation of acids is accomplished by means of Mariotte bottles. On the top level are three steam-jacketed stoneware kettles of 50-gal. capacity, also a packed tower. One kettle is used for digesting the slimes while the remaining kettles are used for precipitating the gold. The dissolver is equipped with a treated concrete hood, which is connected to the flue system. Gases are drawn off through the packed tower by means of a 6-in. stoneware exhaust fan. A 15 per cent solution of sodium carbonate is continually circulated through the tower. On the intermediate level are two suction filters, one for removing silver chloride and the other for the gold sand. The filter medium consists of an asbestos pad covered with a filter paper on which is a layer of twill. On the bottom level are two rectangular cementation tanks, 24 by 48 by 24 in. deep, and a suction filter used for removing the platinum-metal concentrates. The circulating pump for the packed tower is also here. Suction is provided by a vacuum pump having a capacity of 8 cu. ft. at 20-in. vacuum.

Jan 1, 1938

By W. Rostoker, A. S. Yamamoto, K. Anderko

ALTHOUGH the corrosion resistance of magnesium and its alloys is closely related to iron content, there has been no direct measurement of the solid solubility of iron in magnesium. Bulian and Fahrenhors;1 and Mitchel]2 agree that pure iron or a limited terminal solid solution crystallizes from the Mg-rich liquid. For this reason a magnetic-moment method was selected to estimate that portion of the total iron content which is not in solid solution. Since iron in solid solution in magnesium cannot contribute to ferromagnetism, the difference between chemical and magnetic-iron analyses should yield the solid solubility. By experimentation it was found that the melting of pure sublimed magnesium (99.995 wt pet purity) in Armco-iron crucibles at about 800°C is a convenient way to introduce small amounts of iron. Melts retained 5, 10 and 20 min at 800°C analyzed 0.003,, 0.005,, and 0.018 & 0.001 weight pet Fe, respectively, after being stirred, heated to 850°C, and cast into graphite molds. The as-cast alloys were pickled in acid (dilute HC1 + HNO3), annealed at 600°C for 3 days, scalped on a lathe to remove the pitted surface, pickled again, extruded at about 100°C to 3-mm wire, reannealed 41/2 days at 500°C, and water-quenched. The specimens were again scalped, pickled, and used both for chemical and for magnetic analysis. Most of the precautions described were intended to prevent iron pickup by contact with tools or superficial iron enrichment by volatilization of magnesium during heat-treatment. It is believed that the specimens ultimately used for test were homogeneous and characteristic of phase equilibria at 500°C. Magnetic Analyses A susceptibility apparatus of the Curie type was used for magnetic analyses. Field strengths of up to 10,400 oersteds could be generated. By this method, an analytical balance measures the force of attraction which a calibrated magnetic field exerts on a suspended specimen. The force equation is as follows f/m = M dh/dy where f/m = force per unit mass of sample M = magnetic moment per unit mass dH/dy = magnetic field gradient The dH/dy characteristic of the instrument is determined by the use of a standard palladium sample, and the calibration is made independently for all values of H. Since a large finite field is required to saturate an assembly of ferromagnets, it is necessary to measure the apparent magnetic moment for increasing steps of H until a saturation value is obtained. The percentage of iron in the sample as free ferromagnetic iron may then be computed simply C= 100 (M1/M1) where C = percent content of undissolved iron in sample M1 = saturation magnetic moment of sample per unit mass M1 = saturation magnetic moment of iron per unit mass taken as 217 emu-cm per gm There is no serious difficulty in applying this method except for the unusual magnetic behavior of very fine particles of ferromagnetic substances. It has been found and is the basis for a widely accepted theory that with sufficient subdivision, the magnetic fields required to saturate and the coercive force after saturation rise to exceedingly high values. Recent work on precipitates of Fe and Co from copper solid solutions8 showed that about 5000 oersteds were necessary to approach saturation. The magnetic moments as a function of field strength measured in the present investigation are listed in Table I. Only the 0.018 wt pet Fe alloy yielded a magnetization curve with a fairly well-defined saturation plateau at 3.76x10 -2 emu-cm/ gm. This corresponds to 0.017 & 0.001 wt pet Fe in the alloy. This indicates that the solid solubility must be of the order of 0.001 wt pet Fe. The magnetic-moment data of the other two alloys are badly scattered, indicating that the amount of ferromagnetic iron in these samples is so low that the magnetic forces acting on them cannot be measured accurately by the analytical balance used. Nevertheless, the fact that even the 0.003, wt pet Fe alloy shows ferromagnetism indicates that the solid solubility must be below that value. Acknowledgment This work was sponsored by the Pitman-Dunn Laboratory of Frankford Arsenal, Philadelphia, Pa. The support and permission to publish are gratefully acknowledged. References W. Bulian and E. Fahrenhorst: Zeic. Metallkunde, 1942, vol. 34, pp. 116-170. 2 D. W. Mitchell: AIME Transactions, 1948, vol. 175, pp. 570-578. 3 G. Bate, D. Schofield, and W. Sucksmith: Philosophical Magnsine, 1955, vol. 46, pp. 621-631.

Jan 1, 1959

By D. R. Hay, E. Scala

Electrotransport has been superimposed on the rate-limiling- step in zone refining which is the impurity diffusion through the liquid at the solid/liquid interface. The efficiency of zone refining is increased and relative resistivity ratios (P300°k/P4 2°K) he increased by 50 pel in tungsten for a given number of posses using- the electrotransport field-aided method. The effiect of zotze refining in the presence of an electric field on the relative resistivity ratio is examined as a function of its intensity and polarity. THE effect of electrodiffusion on the effective distribution coefficient of zone refining has been discussed by Pfann and Wagner.' Control of the distribution coefficient in zone refining is of twofold interest. A distribution coefficient of unity can be increased or decreased, making possible the transfer of some previously inseparable solutes. The general efficiency of zone refining can also be increased. In the conventional zone-refining process impurities are removed by their retention in the molten zone and subsequent deposition at the end of the rod after a complete passage of the zone. In higher-melting-point systems a second mechanism may also operate, the volatilization of impurities from the molten zone. It has been suggested by schadler2 that, in refractory metals, vacuum distillation plays the predominant role in purification. In Koo's results,3 the resistivity ratio decreased beyond a zone-refined length of 6 in. from the starting end, indicating that some purification does in fact occur by true zone-refining action. Hay and scala4 showed that the degree of purity as measured by the relative resistivity ratio method depends on the square root of time in the molten zone (number of passes) and thus appears to be limited by diffusion in the boundary layer at the solidifying interface assuming good mixing in the body of the molten zone where a linear rate would prevail. The final concentration of impurities in electron-beam floating-zone purification depends very much on the operating conditions and results obtained by various investigators2,3,5 are difficult to correlate. The diameter of the starting material, operating vacuum, and rate of traverse are among the factors to be considered. There are, nevertheless, some general observations to be obtained from the literature. Lawley5 reviewed the literature up to 1962 and concluded that the major contaminants generally remaining in tungsten after electron-beam zone refining are molybdenum and carbon. Molybdenum due to its high melting point and distribution coefficient of nearly unity would be expected to be difficult to remove by either volatilization or zone refining. Carbon is not only a common contaminant in vacuum systems, but is also very difficult to remove by conventional vacuum melting. even with vacuums of 10-7 mm Hg. For each of those impurities removed by zone refining the equation of Pfann and Wagner may be applied: It relates the effective distribution coefficient k to a superimposed driving force which accelerates the solute away from the interface with a terminal velocity L" and to the more conventional zone-refining parameters; v = rate of traverse, t = thickness of the diffusion layer at the solidifying interface, D = diffusivity of the solute in the molten zone, and ko = equilibrium distribution coefficient of the impurity.

Jan 1, 1965

By L. W. Saperstein, Y. J. Wang

The development of computer programs to solve complex ventilation networks has reached a point of refinement where these programs become a necessary tool of the ventilating engineer. Such a program is presented. This program has an increased efficiency over its predecessors; it also includes the important facility of fixed quantity branches. This is in addition to the earlier capabilities of free-splitting, internal or external fans, and natural ventilation pressures. The program is written in Fortran IV with double-precision arithmetic and is listed here. Sample problems with input and output are also given. The recent, and presumably continuing, official interest in mine safety is bound to result in more stringent control requirements for ventilation. Anticipating this requirement, the Dept. of Mining, The Pennsylvania State University, has developed a computer program for the solution of complex mine ventilation networks. It is the opinion of this department that the program has sufficient merit to warrant its use in normal industrial operating conditions. Although the undergraduate mining engineering students of this department are routinely trained to use the program, it was felt that this training did not present a fast enough means of dissemination; consequently, this paper was written. The conception of the program is not new;1; however, the present version incorporates features that changes it from a scientific endeavor to a useful operating tool. These features include those of earlier programs, such as free-splitting, external or internal fans, and natural ventilation processes plus the important ability of handling fixed quantity branches, and of increased efficiency giving reduced cost. The facility for fixed quantities will be discussed in more detail. The solution of any network depends upon satisfying Kirchchoff's laws. These state that the sum of flow at any junction is zero, and that the sum of the pressure drop in branches totals the pressure drop in the mesh constituted by those branches, that is that the pressure drop around any mesh is zero. The terminology is derived from Synge," and is, in fact, that used by Topologists. A branch is any airway of uniform characteristics; a junction is where two or more airways meet (the minimum number of two airways is useful for describing the point where a low resistance airway changes into a high resistance one due to some physical constriction); a mesh is a path, along some branches, that returns on to itself, but does not need to traverse the same branch twice in order to do so; and a tree describes all those branches in a network which, while connected through all the junctions, do not form any meshes. Obviously the branches-in-tree are open-ended and can be shown to be one less than the number of junction (J-1). The branches-out-of-tree, also called basic branches, are equal to the number of basic meshes and are M = N — J + 1, where M is the number of meshes and N is the number of branches. The major difference between this network and an electrical one is that the law attributed to Atkinson for pressure drop is utilized rather than Ohm's law. Atkinson stated that the pressure drop (potential) is equal to a resistance factor multiplied by the quantity squared. This is written H = RlQlQ where H is the head loss. Q? is written in this factored fashion so that H will always have the same sign as Q. A negative sign is used to indicate that flow in a branch is opposite to that of its containing mesh. A mesh takes the direction of its basic branch. Utilizing Atkinson's law in Kirchchoff's second law and bearing in mind that the first law must remain satisfied, the program will determine all quantities, or head losses as they are related, for the branches of the network. The program uses a Geuss-Seidel form of in-teration, starting from an arbitrary Q and using a correction factor of the type first suggested by Professor Hardy Cross' that will handle the nonlinear equation of Atkinson's law. A fuller description of the interative process is included in Wang and Hartman.' Iteration continues until the correction factor is less than or equal to a preset error (E) or until a maximum number of iterations (MAXIT) have been reached. Utilizing an E of 50 cfm, sample problems have had rapid solutions. Rapidity of solution is also ensured by the method of selecting meshes and basic branches. This is done by the computer, which chooses the highest resistance branches, fixed quantity branches, and those containing fans, as basic branches. Natural ventilation pressures are handled as fans of constant pressure and may be assigned to any branch. The computer will generate a fan characteristic by polynominal fitting if a few operating points from the desired fan are input. A fan may be placed in any branch of the network, except those with fixed quantities. The strength of the present program over its earlier versions is its ability to handle fixed quantity branches. This means that certain branches can have their quantity determined, or preset, by the ventilating engineer. Operating under this constraint, the program will analyze the network and output the pressure change necessary to achieve this desired quantity. A call for positive head loss would require an auxiliary fan; negative head loss would require a regulator. This represents a powerful tool for the ventilating engineer who must insure that certain quantities of air pass across the operating faces or through working stopes. McPherson6 suggested that a ventilation program would be useful for determining in advance which branches were receiving inadequate air, and that subsequent calculations would then indicate the necessary corrections. The present program makes these corrections. Thus the mine manager can know immediately the consequences of changes to his system;

Jan 1, 1971

By S. M. Purdy

Under certain conditions of hot rolling and air cooling from the hot-rolling temperature, bars of a high carbon (0.40 pct C) chrome-nickel austen-itic alloy were found to show magnetism even though no ferrite or martensite could be detected by microscopic or X-yay methods. The appearance of magnetism in such alloys may come from chromium impoverishment of the austenite grains near the precipitated carbide particles. SPORADICALLY, hot-rolled bars of Silchrome 10, an exhaust valve steel, have been found to be magnetic. Because of the analysis of the alloy—0.40 pct C, 18 pct Cr, 8 pct Ni, 3 pct Si —magnetism is unexpected. Preliminary investigation showed neither martensite nor ferrite to be present; only austenite and Cr23C6. Since a literature search was fruitless, a brief study was made of the appearance of magnetism in this alloy. The only basic difference between the two heats is the nitrogen content. Permeability was measured using a Severn magnetic gauge. This instrument consists of a magnet mounted on a counterbalanced arm. A set of calibrated plugs is placed in contact with one pole of the magnet. The specimen is placed close to the other pole of the magnet. If the specimen pulls the magnet away from the plug, it has a permeability greater than that marked on the plug. This technique is swift and reproducible. Previous experience has shown that the permeabilities obtained corresponded to those obtained on a permeater with a field strength of 100 oe. Specimens from both heats were annealed at temperatures between 1700 and 2300°F. One set of specimens was water cooled and another furnace cooled. All the water-quenched specimens were non-magnetic; the furnace cooled ones were magnetic as shown in Table I with no difference being observed between the two heats. Microstructural examination of the specimens showed the expected increase in carbon solubility with increasing temperature. Carbide solution was complete at 2200°F. The specimens heated to 1900°F or below showed some carbide precipitation from the hot-rolled structure. A furnace cooled specimen from a given temperature showed less carbide out of solution than the water-quenched specimen from the next temperature below; e.g., the specimen furnace cooled from 2100°F showed less carbide out of solution than the water-quenched specimen from 2000" F. These studies indicated that the appearance of magnetism was not related to the quantity of carbon in or out of solution and it was related to precipitation at temperatures below 1700" F. A set of samples annealed and water-quenched from 2100° F was aged for 4 hr at temperatures between 1000" and 1600°F; all were non-magnetic. A second set of samples, similarly annealed, was aged 1 to 24 hr at 1200°F with the results shown in Table II. None of the latter set of specimens showed magnetism until they had been aged about 8 hr. Magnetism was quite strong after aging 24 hr. X-ray diffraction studies on several of the magnetic specimens showed that the austenite had a lattice parameter of 3.58A and that the carbide was Cr23C6. Several of these samples were electrolytically digested in 10 pct HCl in ethanol, with a current density of 0.1 amp per sq cm. None of the particles in the residue were magnetic. Accidentally, one cell was run at 1 amp per sq cm; e.g., magnetic particles were found in this residue. After careful separation, the magnetic particles were mounted on a quartz fiber and their diffraction pattern determined using a 5.73-in. Debye-Sherrer camera with CrK radiation. These particles showed a fcc structure with a lattice parameter of 3.57A. Prolonged exposure, up to 16 hr, produced no other lines on the film. The following facts seemed to be established at this time: 1) Austenite was the magnetic phase. 2) Neither ferrite nor martensite could be detected. 3) Magnetization could be produced by aging at 1200°F. One explanation of these data is that the carbide precipitation impoverishes the region immediately around the carbide particle of carbon and chromium and increases the proportion of nickel. All of these serve to increase the Curie temperature of the region around the carbide particle. If the composition change is enough, the Curie temperature will rise above room temperature. If the volume of the affected region is great enough, the magnetism will become detectable. At low aging temperatures, composition changes are great enough but the overall volume of impoverishment is quite small

Jan 1, 1962

By R. J. Schaefer, M. E. Glicksman

Direct, in situ observation of metallic alloys during solidification reveals that in some systems crystal multiplication occurs by means of a dendrite remelt-ing process, without the necessity of independent nu-cleation events. The solidification is observed on optically clean surfaces of supercooled molten alloys. In one system (Sn-3 wt pct Bi) , a fine-grained equi-axed structure is produced by the complete disintegration, via remelting, of transient initial dendrites. In contrast, several other metallic systems show little or no evidence of remelting activity. The behavior of these metallic systems is consistent with that expected on the basis of published observations of dendrite remelting in transparent organic alloy systems. It is concluded that dendrite remelting is an important crystal multiplication process in some metallic alloys, but is velatively unimportant in some other alloys. The detachment of dendrite branches from the primary stem by a remelting process has been observed by Jackson, Hunt, Uhlmann, and seward1 during the solidification of some transparent organic alloy systems. The branches released by this remelting process can drift free of the primary stem and serve as seeds for the formation of numerous independent crystals. This proliferation of new crystals does not require repeated independent nucleation events, but only modification of the initial solidification structure. The mechanism of dendrite remelting, as described by Jackson et a1.1 and by Tiller and O''Hara,2 is dependent on the transport of both heat and solute and is, therefore, expected to operate only in alloys, and not in pure substances. It was found in the transparent organic alloy systems that remelting occurred primarily in the constricted regions near the base of dendrite branches, where the branches had grown through the solute-rich liquid layer surrounding the primary dendrite stem. It was suggested that impure solid had formed in these constricted regions at a relatively low temperature and had later become unstable as further solidification of purer material raised the temperature. Jackson et al. proposed that the equiaxed zone of metal alloy castings originates from a similar remelting process, and they demonstrated the operation of this mechanism in "ingots" poured from saturated salt solutions. Although these substances were especially selected to show solidification behavior similar to that of metals,3 the remelting mechanism has, until now, been subject to the objection that its operation has not been directly observed in a metallic system. Considering the fact that thermal properties such as diffusivity may differ by as much as two or three orders of magnitude between metals and organic compounds, this objection was considered to be possibly serious. A method has now been developed by which it is possible to make direct optical observations of metals during solidification. This method has revealed transient solidification processes which would not be detected by metallographic examination of totally solidified specimens. In particular, a grain-refinement process in a metallic alloy has been observed to be a direct consequence of the total disintegration of an initial dendritic structure. The influence of an initial, transient solidification structure on the final solidification structure is demonstrated here for the first time in a metallic system. I) EXPERIMENTAL The technique of using a transparent flux to maintain an optically clean metal surface during solidification has been described by us elsewhere.* The

Jan 1, 1968

By Russell A. Carter

Seven years of rising silver prices have effectively revived an historic Idaho mining district and given it a new lease on life. Initial production earlier last year from the DeLamar open-pit silver mine in southwestern Idaho ushered in a new era of mineral production in a region that has weathered boom-and-bust cycles reaching back the better part of a century.

Jan 1, 1978

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

By B. D. Harden

FOR over fifty years the Spanish mine, 21 miles northeast of Nevada City, in Nevada County, California, has been one of the Bradley properties. Between 1883 and 1889 it was operated by the late Frederick W. Bradley and P. R. Bradley. The ore averaged only about $1 a ton at that time but the mine was credited with a production of about $900,000 in that period. The property was then closed down until 1922, when the Bradley interests reopened it and continued development for the next nine years, when a 50-ton mill was built. This began operation in April, 1931. This was a selective flotation plant, with the tailing treated on Wilfley tables, and operated on ore from the No. 4 and No. 16 tunnel stopes. This ran from $3 to $6 in gold, 2 to 3 oz. of silver, copper 0.6 per cent, lead 1.5,

Jan 1, 1935

By David Cornell, Yusuf K. Sukkar

The fundamental differential equation for fluid flow has been rearranged, integrated numerically for natural gases, and the results presented in tabular and graphical form suitable for the direct calculation of vertical gas flow problems. The integration is rigorous except for the use of a constant average temperature. Both static and flowing bottom-hole pressures may be calculated by (his method without resort to trial and error procedures. INTRODUCTION Bottom-hole pressures can be determined either by direct measurement with a bottom-hole pressure gauge or by calculation. Since measurement with a bottom-hole pressure gauge is costly, calculation of bottom-hole pressures is to be preferred when possible. Calculation involves knowledge of the wellhead pressure, the properties of the gas, the depth of the well, the flow rate, the temperature of the gas, and the size of the flow line. These quantities must be combined in a suitable equation for vertical flow. Several equations have been developed for the purpose of calculating gas flow through both horizontal and vertical pipes1,2,4,5,6,7,8,9 These equations all have the basic differential equation for flow as their starting point. They differ only in the assumptions which are made in order to simplify the integration step. The bottom-hole pressures calculated using any of the better known equations are in good agreement with bottom-hole pressures calculated by a more rigorous but considerably more tedious stepwise integration method. All of these methods, however. require a trial and error solution for the calculation of flowing bottom-hole pressures. The purpose of this paper is to present a method which provides a direct solution of static and flowing bottom-hole pressures without use of a trial and error solution. At the same time the method involves fewer simplifying assumptions than any of the previous methods used, except lor the lengthy stepwise method. The derivation of any practical flow equation begins with the basic differential equation which is rigorous for almost all flow problems. The five terms in Equation 1 represent the potential energy, the potential energy of position, the kinetic energy, the shaft work done, and the energy losses due to motion of the fluid respectively. Equation 1 reduces to Bernoulli's theorem for the case of horizontal flow of an incompressible fluid, no work done, and no energy losses due to friction. In the present case, the term (v) (dv)/(g,.) can be shown to be quite negligible compared to the other terms, and is therefore neglected in the derivation. The term — dws includes work done by a pump or turbine in the system and is zero in this case. The frictional losses in the pipe are included in the term — d(lw) which is expressed in terms of the Moody friction factor as in Equation 2. (f) (v2) (dL) d(lW) = (f)(V2) (dl)/(2) (g) (d) The specific volume of a gas can be expressed in terms of the temperature, pressure, molecular weight, and compressibility factor. The velocity of the gas can be expressed in terms of the weight rate of flow, the specific volume, and the dimensions of the pipe.The reduced pressure Pr is to be used because z can be expressed as a function of Pr and Tr alone for most natural gases:

Jan 1, 1956

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By Nicholas J. Grant, John S. Benjamin

A series of composite alloys containing a high volume of NiAl, Ni3Ah or CoAl, bonded with 0 to 40 vol pct of a ductile metal phase, were prepared by powder blending and hot extrusion. The binder metals were of four types: pure nickel or cobalt, near saturated solid solutions of aluminum in nickel and cobalt, type 316 stainless steel, and niobium. Sound extrusions were obtained in almost all instances. Studied or measured were the following: interaction between the alunzinides and the binders, room-temperature modulus of rupture values, 1500° and 1800°F stress rupture properties, hardness, structure, and oxidation resistance. Stable structures can be produced for 1800°F exposure, with interesting high-temperature strength and good high-temperature ductility. Oxidation resistance was excellent. A large number of experimental investigations have been made of the role of structure on the properties of cermets and composite materials. Gurland,1 Kreimer et al.,2 and Gurland and Bardzil3 have indicated the preferred particle size in carbide base cermets to be about 1 µ, with a hard phase content of 60 to 80 vol pct. The optimum ductile binder thickness was noted to be 0.3 to 0.6 µ.1 Complete separation of the hard phase particles by the binder is important in reducing the severity of brittle fracture.' The purpose of the present study was to produce structures comparable to the conventional cermets, using a series of relatively close-packed intermetal-lic compounds rather than carbides as the refractory hard phase, and to study the effects of binder content and composition on both high- and low-temperature properties. The selected intermetallic compounds were particularly of interest because of the potential they offered in yielding room-temperature ductility. The highly symmetrical structures are known to possess high-temperature ductility and room-temperature toughness. Based on a ductile binder, the alloys were prepared by the powder-metallurgy route to avoid melting and subsequent alloying of the matrix, and were extruded at relatively low temperatures. It was expected that the composite alloy would retain useful ductility. In contrast, infiltration and high-temperature sintering led to alloying of the matrix and to decreased ductility. The systems Ni-A1 and Co-A1 were selected for this study. In the Ni-A1 system the compounds NiA1, having an ordered bcc B2 structure, and Ni3Al(?1), having an ordered fcc L12 structure, were chosen. In the system Co-A1 the intermetallic compound CoAl with an ordered bcc B2 structure was used. ALLOY PREPARATION The intermetallic compounds, see Table I, were prepared by using master alloys of Ni-A1 and CO-A1, with additions of either cobalt or nickel to achieve the desired compositions. The master alloy in crushed, homogenized form, was melted with pure nickel or cobalt in an inert atmosphere, cold copper crucible, nonconsumable tungsten arc furnace. The resultant intermetallic compounds were homogenized at 2192°C in argon, crushed, and dry ball-milled in a stainless mill to -100 and -325 mesh for the Ni-A1 compounds and to -325 mesh for the CoAl compound. Finer fractions were separated for some of the composite alloys. Several ductile binders were utilized. These included Inco B nickel, 5µ ; pure cobalt, 5 µ, from Sher-ritt Gordon Mines, Ltd.; fine (-325 mesh) niobium hydride powder; fine (15 µ) type 316 stainless-steel powder; and near-saturated Ni-A1 and Co-A1 solid-solution alloys, also in fine powder form. The niobium hydride was decomposed above about 700°C in processing of the compacts in vacuum to produce niobium powder. The Ni-7.1 pct A1 and the Co-5.3 pct A1 solid-solution alloys were prepared from pure nickel or cobalt and pure aluminum by nonconsumable tungsten arc melting under an inert atmosphere. The ingots were homogenized, lathe-turned to fine chips, and dry ball-milled in air to -325 mesh powder. These solid-solution alloys are designated NiSS and CoSS; see Table I. Subsequently the hard and ductile phases were dry ball-milled as a blend. Experiments clearly established the need to coat the hard particles with the ductile binder to optimize subsequent hot compaction by extrusion. Ordinary dry mixing usually resulted in nonhomogeneous alloys which were quite brittle. Conventional cermets are consolidated by liquid phase sinteiing or infiltration, which resulis in undesirable and uncontrolled alloying of the binder phase. For this study, a loose (unsintered) powder-extrusion process was emploved, minimizing reactions between binder and hard particle, thereby permitting much greater control of composition and structure. The constituent powders were first mixed in the desired

Jan 1, 1967

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

By M. B. Bever, A. B. Michael

THE structure of cast A1-Si alloys is altered profoundly by modifying agents. Sodium, in particular, reduces the size of the silicon particles in the eutectic and tends to change their shapes from plates to nearly rounded grains. This refinement is accompanied by a shift of the eutectic to higher silicon concentrations and lower temperatures. Similar effects can be attained by rapid solidification. Hypotheses advanced to explain modification have involved the formation of a ternary eutectic,1 the removal of oxides by fluxing,&apos; and even a presumed allotropic transformation of silicon. Other hypotheses assume that the modifying agent causes an envelopment of the silicon particles by the aluminum-rich solid solution, but attribute this envelopment to different mechanisms. According to various explanations, the growth of the silicon particles is obstructed by an immiscible sodium-rich liquid," an adsorbed layer of sodium,&apos; or a ternary compound;5 his obstruction has been conceived as purely mechanical or as a colloidal action.&apos; It has also been proposed that sodium reduces the surface tension on the Al-Si interface, thus permitting the aluminum-rich solid to grow faster and to envelop the silicon particles.? Still other hypotheses stress undercooling and the attendant change in the rate of nucleation of silicon, but fail to ascribe any definite function to the sodium addition." &apos;" Procedure High-purity alloys of aluminum and 3 or 7 pct Si were treated with modifying agents containing radioactive sodium tracers. The experiments were intended to investigate the partition of sodium between the primary aluminum-rich solution and the eutectic, and, if possible, to determine whether sodium is concentrated in or around the silicon particles in the eutectic. Radioactive sodium fluoride, alone or mixed with stable sodium chloride, was allowed to react with the alloy for 5 min immediately before solidification in the crucible. Modification could not be attained with additions of less than the equivalent of approximately 0.1 pct Na. Some alloys were not completely modified, but comparison of the structures of treated and untreated specimens indicated a very considerable reduction in particle size of the silicon in all of the former. A treated alloy is shown in Fig. 1. Radioactive sodium fluoride was prepared by bombardment with deuterons having an energy of 14 mev. This bombardment (totaling, for example, 6 microampere-hours in one run) produced radioactive Na24 (half-life 14.8 hr) by the reaction 11Na23 (d,p) 11Na24. The radioisotopes of fluorine also produced have short half-lives and were not detected. A half-life determination by counting confirmed that the measured activity was due to Na24. The distribution of the sodium in the solidified alloys was determined by an autoradiographic technique by which a suitable stripping film is attached to a very thin metallographic specimen. After exposure and development, this emulsion remains superimposed on the specimen and may be examined microscopically or photographed by reflected light. The emulsion of the autoradiograph can be correlated directly with the underlying surface by simple adjustment in focus. The details of this technique have been described elsewhere." Results Fig. 2 is a micrograph of the autoradiographic emulsion ("autoradiograph") lying directly above the area of eutectic in Fig. 1. Fig. 3 shows a similar autoradiograph of a region consisting of primary solid solution. The small black dots (tracks) in these autoradiographs are developed grains in the emul-

Jan 1, 1954

By J. W. Rutter, K. T. Aust

The temperature dependence of the rate of grain boundary migration was measured in bicrystals of zone-refined lead containing from 20 to less than 1 ppm by wezght of tin. The apparent activation energy in the temperature range from 320" to 200oC is markedly dependent upon the solute tin concentration and upon the orientation relationship of the grains adjacent to the grain boundavy. The quantitative experimental observat~ons are compared with the predictions of various theories of grain boundary migration. In previous work.&apos;?&apos; the mobility of individual grain boundaries was studied as a function of impurity concentration and type of boundary. Grain boundary migration occurred at the expense of dislocation arrays which were introduced into the specimen during solidification. Boundary mobility in zone-refined lead at 300°C was markedly decreased by small additions of tin. 0.004 wt pct being sufficient to decrease the rate of grain boundary migration by a factor of 1000. The mobility of grain boundaries having polar orientation relationships near 38 and 22 deg about <Ill>, and 28 deg about <100>, was much less sensitive to tin concentration in the range studied. As a result, these boundaries have relatively high mobilities. The present paper is a continuation of the above study. Data are now presented on the temperature dependence of the motion of individual grain boundaries in zone-refined lead as a function of solute tin concentration and orientation relationship of adjacent grains at the grain boundary. The experimental observations are compared with the predictions of a number of theories of grain boundary migration3-8 which, prior to the present experimental investigation, could not be critically evaluated. EXPERIMENTAL PROCEDURE The striation or lineage structure of melt-grown single crystals of zone-refined lead, containing various additions of tin, was utilized to provide a driving force for grain boundary migration, as previously described.1,2 Each grain boundary under study separated the striated single crystal from another grain which was introduced by localized plastic deformation and recrystallization of a small region of the sample. The speed of migration of grain boundaries in dilute alloys of tin in zone-refined lead was investigated as a function of 1) tin concentration from < 0.0001 to 0.002 wt pct, 2) temperature in the range of 200" to 320°C, and 3) orientation relationship of the adjacent grains at the grain boundary. The substructure driving energy available for grain boundary migration was estimated to be about 4000 ergs per cu cm, within a factor of two, from specimen to specimen.&apos; The specimen dimensions, and growth and alloying procedures for the preparation of striated single crystals of lead of known tin composition, were as described previously.&apos; Each bicrystal was carefully wrapped in aluminum foil, and annealed in a well-stirred salt bath consisting of 50 pct NaNO2 and 50 pct KNO3, for known periods of time at a series of constant temperatures (*2°C). The grain boundary positions, before and after each anneal, were determined by etching lightly in a solution of 5 pct nitric acid in methyl alcohol, in order to follow the motion of the boundary and determine its rate of migration. Thus, the rate of motion of the grain boundary in a single specimen was measured at various temperatures. The above procedure was carried out for each grain boundary in seventeen different bicrystal specimens.

Jan 1, 1960

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800&apos;s when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By R. L. Watts

Successful mining of taconite has required the solution of a series of difficult problems, including more efficient magnetic separation. Progress in this field is evidenced by reductions in operating and capital costs made possible by the advances in permanent magnetic materials and in new circuits for better utilization of these materials. The advent of the flux control circuit appears to be one of the more important breakthroughs in permanent magnet drum design circuitry and has contributed greatly to the economics and metallurgical requirements of the modern day taconite concentrators. High strength permanent magnetic separators are now replacing electro types in many applications requiring field strengths of 900 - 1000 gauss measured at 2 in. This is made possible by the new circuits having gauss readings at 2 in. previously attained only by electromagnets.

Jan 12, 1967

By L. A. Morley, W. T. Parry

Laboratory prepared clay-quartz sand samples and fault gouge from an open pit slope undergoing plane-type failure were tested in the laboratory to determine potential mining applications of electroosmotic stabilization and to provide a better understanding of electrochemical hardening. Experiments with very low current densities and free access of electrolytes to both anode and cathode showed an increase in cohesion. Cohesion in a fault gouge increased by 9.3 to 113%, depending on location with respect to the electrodes. For this, power consumption was equivalent to 0.727 watt-hr per cu ft (25.69 watt-hr per cu m). Regions of electrochemical hardening were determined by pH and the anolyte used. Electroosmotic stabilization appears as a reasonable solution to some types of mining problems.

Jan 1, 1975

By F. B. WEEKS

I HAVE chosen for my subject a mining district which in an article published four years ago I referred to in the following words: "One of the un- usual anomalies of mining development and history is that a district having added thirty or more millions of wealth to a principal mining state, situated within four to six miles of two transcontinental railways and two auto highways, and within 150 miles of the most widely advertised part of the United States, should have been so completely lost sight of that probably not one mining man in ten can tell offhand where it is situated." But this district never was a dead one: it was only slumbering. During the past four months, day by day, it has been emerging from that state of slumber.

Jan 1, 1929

By KENNETH W. GREENAWALT, William Greenawalt

THE patent system, through which an inventor is given exclusive right to his invention for a limited period as a reward for his industry and in reimbursement of his expenditures, originated in England in the famous "Statute of Monopolies," enacted in 1623. The first patent granted in America was to Samuel Winslow, in Massachusetts, in 1641. The basis of the patent system of the United States is a provision in the Constitution giving Congress the power to secure to inventors for a limited time the exclusive use of their discoveries. The first legislative enactment was the law of 1790, which was placed on the statute book after Washington had addressed Congress in its favor. Under this law, the Secretary of State, the Secretary of War, and the Attorney General constituted the board for the examination of patent applications and the granting of patents. The first Secretary of State, Thomas Jefferson, became the first administrator of the patent sys- tem in this country. He personally examined every application filed during his term of office.

Jan 1, 1930