Search Documents

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By W.M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By W. M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.'," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

G. A. Burr, Parral, Chihuahua, Mexico (communication to the Secretaryt): I regret that Mr. Norris did not give more attention to the hoisting of water in inclined shafts or slopes: the only slope mentioned being Hickory Ridge Slope, No. 4, of the Union Coal Co. The surface arrangement, illustrated in Fig. 12 of his paper, if not unpractical, is at least unscientific and cumbersome. It is my opinion that the back- and sideguides shown in Fig. 12 are not only unnecessary where rails are used as a track, but are unsafe, excepting in the case of a very firm hanging-wall, or roof, and sides of vein-matter, having absolutely no tendency, either to settle from the back, or to squeeze from the sides, an effect which would inevitably force the guides out of alignment. The accompanying illustration, Fig. 1, shows what I consider a better method of hoisting water than that described by Mr. Norris. This method is based on the general practice in metalliferous mines of the West, where skips are used in slopes; and, while it is not original with me, I have frequently used it with very satisfactory results for dumping both ore and water.

Jan 1, 1904

FOR four years your Committee has been engaged in the study of problems connected with the educational preparation of professional geophysicists. The present report represents the conclusions drawn from the investigations and deliberations undertaken since it was first organized. These studies have shown that the evolution of geophysics has proceeded along lines that differed from those marking the advance of classical geology. The latter science developed as a descriptive one, dealing with directly observable terrestrial phenomena, and the elementary, rational explanations that could be offered therefor. The fact that these phenomena were also chemical and physical in nature was seldom given more than passing acknowledgment. During the last half century, however, a new approach to problems of terrestrial phenomena has become of greater significance. This new attack has come through the sciences of physics and chemistry, as the people trained therein have investigated the facts of the earth as problems in their respective sciences. This development has been chiefly at the hands of European investigators, and European universities have long recognized it by establishing departments or institutions of geophysics. In the universities of North America, their arbitrary departmentalization into fields of physics, chemistry, astronomy, geology, etc., has prevented the academic recognition of such domains of science as geophysics and geochemistry. In consequence, the development of these subjects in the United States has been largely at the hands of nonacademic institutions, while the universities themselves are evidently in a state of confusion as to how the subject should be handled. In some places an attempt to teach geophysics is made in the physics department, in others in the geology department, in some in the engineering school, and occasionally as a cooperative effort; a Department of Geophysics is seldom found in North America. In some instances, proper academic planning has been precluded by interdepartmental jealousies, or by lack of appreciation of the significance of the subject. For the background upon which these conclusions are based, the reader is referred to reports previously issued or sponsored by your Committee. These reports are available from Institute Headquarters. The "First Report of the A.I.M.E. Mineral Industry Education Division's Committee of Geophysics Education, 1939," summarizes the replies received to question-

Jan 1, 1942

By C. R. Sandberg, L. S. Gournay, R. F. Sippel

The effect of fluid-flow rate and fluid viscosity on oil-water relative permeability determinations was studied using the "dynamic flow technique." In this work relative per-nleability curves were obtained for homogeneous small core .samples from several sandstorle outcrop form-utions. Radio-tracers were used for the determination of fluid saturation and for the detection of saturation gradients. Cobalt-60 in the form of cobaltous chloride was used as a water-phase tracer in some of the experiments. Iodine-131 in the form of iodobenzene and Mercury-20-3 in the form of mercury diphenyl were used as oil-phase tracers in other experiments. Flow rates for each phase were varied within a range of 2.5 to 140.6 ml/hr. Oil-phase vis-cosities under flowing condition,> were varied from 0.398 to 1.683 cp. The relative permbilities ob-tained were found to he solely a function of saturation and independent of flow rare, provided there was no .Saturation gradient induced in the core sample by "boundary effect." Even though equilibrium with re-sped to flowing conditions was obtained at the lower flow rates, where a saturation gradient exists, this equilibrium is of a "contingent"-type rather than the "steady-state" equi-librium implicit in the relative per-meability concept. The only effect of increasing the oil or non-wetting phase viscosity was to decrease the flow rate required for the elimina-tion of the boundary effect. Fairly good agreement between experimentally determined and calculated values of the boundary effect was obtained when the non-wet-ring oil phase was the only Flowing phase. INTRODUCTION In the characterization of reservoir rock, as well as in the solution of reservoir production problems, it is most desirable to have reliablc rela-tive permeability measurements for the rock and fluids of interest. Many techniques have been developed for the laboratory determination of the relative permeability of both large and small core samples. In varying degree, difficulties attend the use of all of the methods. Each of the methods requires the metered flow of fluids of known viscosity through the core sample under conditions wherein the pressure drop in the individual flowing phases can be measured or closely approximated. Since the relative permeability is a function of the saturation and distribution of the flowing fluids, some means of obtaining such information is also required. The laboratory determination of the relative permeability of a sample should give the same relative permeability saturation relationship that would exist if the sample were in place in the oil reservoir. The attainment of this objective is complicated by the fact that the use of small core samples for laboratory measurements is usually necessary. As a result, errors in measuring the relative permeability arise from boundary effects at either the fluid input or output ends of the sample; no significant boundary effect is anticipated at the sides of the sample normal to direction of fluid flow. At the input end of the sample a boundary effect exists if the flow fluids are not com- mingled as they would be in the reservoir. At the output end of the sample a boundary effect exists as a result of discontinuity of the capillary properties of the system. Here the flowing fluids leave the small flow channels and enter a collecting system having much enlarged flow channels. Thus, there is a tendency for the wetting phase to be retained by the core sample because of the attraction of the core sample for the wetting fluid. No reference is made to these boundary effects in either Darcy's equation or in the relative permeability concept. As a consequence the saturation effect peculiar to the input end of the core sample may cause an error in the effective permeability measurement, since some portion of the core sample must be utilized for commingling of the flow fluids. At the output portion of the core sample a saturation gradient or a saturation change along the axis of flow results. Since relative permeability is a function of fluid saturation, this saturation gradient may cause a variable permeability measurement, especially since extent and character of the saturation gradient can vary with fluid-flow rate. The most convenient method of minimizing the boundary effect, especially at the output end of the sample, is to flow the fluids of interest through the core sample at such high rates that the capillary forces arc insignificant as compared to the viscous forces involved in the fluid flow. Since recent work of a preliminary nature has indicated that fluid dispersion in the porous medium increases with the flow rate, the high flow minimizes the boundary effect at the input end of the core sample by enhancing the mixing of the fluids.

By C. Perez-Rosales

A statistical method for determining simultaneously some of the basic geometrical characteristics of porous media such as porsity, specific surface* mean pore width, mean grain thickness and absolute permeability is presented. The proposed method is characterized by its simplicity and the minimum amount of laboratory equipment that it requires. The experimental procedure used to evaluate the various geometrical characteristics is based 'pan the 'surface analysis Of a a In view of this fact the app1icability Of the method is limited to homogeneous and isotropic materials. INTRODUCTION The behavior of a fluid flowing through a porous medium depends, among other things, upon the internal geometry of the medium; hence the importance of developing efficient methods to determine the geometrical properties of porous materials. This paper describes a statistical method to determine simultaneously some of the basic geometrical properties of porous materials such as porosity, specific surface, mean pore width, mean grain thickness and absolute permeability. The mathematical formulation has been developed that the data required to calculate the various geometrical characteristics of a sample can be easily measured by analyzing a section of the sample with an evenly spaced grid. THEORY A simple way of obtaining information about the internal geometry of a porous material is to throw a point at random over a cross-section of a sample. l-Through this procedure the porosity can be detemined.l,2 By considering that the material is homogeneous and isotropic, and that the point is dropped many times, the porosity 4 is given by where N is the total number of times the point is thrown and n is he number of times the point falls within pore areas. Another simple manner of analyzing the structural characteristics of a porous material is to superimpose an arbitrarily long line on a cross-section so that its length is evenly distributed over the surface area. Through this procedure the porosity can also be determined. If L is the total length of the line, and 1 is the sum of the lengths of the line segments within void spaces, the porosity is given by 4 = —.1.............. (2) The advantage of this type of analysis is that geometrical characteristics other than porosity can be obtained. Thus, if c represents the number of intersections between the line and the perimeter of pores, it can be shown3 that the specific surface, defined as he surface area of pores per unit bulk volume, is given by To give a proper description of the internal geometry of a porous medium, it is necessary to define quantities that characterize the notions of pore size and grain size. Unfortunately, because of the complexity of porous materials, it is difficult to give exact geometrical definitions of what is meant by the ConCePtS of "poresl' and "grains", especially when dealing with consolidated materials. Never theless, one often talks about the "size of pores" and the "size of grains" without defining accurately the terms. A possible solution to this problem follows. Assume that an arbitrarily long line is placed on a section of a sample so that the line is evenly distributed over the surface area (see Fig. 1). 1n a system like this, each line segment within a void space will be, by definition, the pore width in a given location and direction. Consequently, if the

Jan 1, 1970

For some time attempts have been made to improve drilling efficiency (and therefore reduce costs) by introducing certain reagents to the flushing medium. Much of this interest is the result of the Russian book, Hardness Reducers in Drilling, by Rehbinder, Schreiner, and Zhigach, published in 1944. Before embarking on full-scale drilling tests, it was decided to investigate the effects on the tensile strength; these results would help in the selection of the proper reagent and its optimum concentration. Selection of Tensile Strength Testing A drilling system basically performs two separate operations: 1) Breakage of rock. 2) Removal of the broken pieces of rock. Both affect drilling and drill performance but are distinct and separate phases of the process. Causing rock to break during drilling is a matter of generating sufficient stress with a drill bit to exceed the strength of the rock. This strength of the rock may be termed its drilling strength; it is not equivalent to any of the well-known strength parameters. Various criteria have been employed to measure the efficiency of a given drilling system or for comparing different systems and one of the most important criteria is "speed of drilling." Speed of drilling is a function of drilling strength of the rock. Many researchers have tried to correlate the speed of drilling with the strength properties of rock and compressive as well as tensile strength values have been found to give reasonable correlation." As the strength of rock drilled increases, speed decreases. As the Brazilian testing requires the least amount of core, this test was selected. Material Tested Broken Hill lode quartzite has been used in these tests. It is composed chiefly of quartz with varying amounts of sericite, pyrrhotite, chalcopyrite, galena, and garnet. The total porosity of this quartzite is about 11%.

Jan 1, 1973

By I. R. Kramer

Studies of the effect of size of the specimen on the change of slopes of Stages I and 11 by surface removal showed that the change of Stage I was independent of size with respect to the polishing rate; however, the change in the slope of Stage 11 with polishing rate increased directly in proportion to the surface area. The removal of the surface during the test affected the plastic deformation characteristics of gold, aluminum, and zinc single crystals and polycrystalline aluminum. The apparent activation energy of aluminum was found to be decreased markedly by removing the surface during the deformation process. In previous papers1-3 it was shown that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing during tensile deformation, it was found that the slopes of Stages I, II, and III were decreased and the extents of Stages I and II were increased when the rate of metal removal was increased. By removing a sufficient amount of the surface layer after a specimen had been deformed into the Stage I region, upon reloading, the flow stress was the same as the original critical resolved shear stress and the extent of Stage I was the same as if the specimen had not been deformed previously. The slope of Stage I was decreased 50 pct and that of Stage 11 decreased 25 pct when the rate of metal removal was 50 X 10"5 ipm. These data show that in Stage I the work hardening is controlled almost entirely by the surface conditions, while in Stages 11 and III both surface conditions and internal obstacles to dislocation motion are important. It appears that during the egress of dislocations from the crystal, a fraction of them becomes stuck or trapped in the surface regions and a layer of a high dislocation concentration is formed. This layer would not only impede the motion of dislocations, but would provide a barrier against which dislocations may pile up. In this case, there will be a stress, opposite to that of the applied stress, imposed on the dislocation source and dislocations moving in the region beyond this layer. It has been found convenient to refer to this layer as a "debris" layer. The "debris" layer may be similar to the dislocation tangle observed by thin-film electron microscope techniques.4 Reported in this paper are the results of studies on the effects of removing the surface during plastic deformation on aluminum crystals of various sizes. The effects of the surface on the yield point behavior of gold and high-purity aluminum crystals as well as the creep behavior were also determined. The effects of surface removal on polycrystalline aluminum (1100-0 and 7075-T6) are also reported. EXPERIMENTAL PROCEDURE For those portions of the investigation involving creep and tensile specimens, single crystals, having a 3-in. gage length and a nominal 1/8-in. sq cross section, were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The single crystals were prepared from materials which had initial purities of 99.997, 99.999, 99.999, and 99.999 pct for Al, Cu, Zn, and Au, respectively. The aluminum specimens for the size effect studies were prepared through the use of a three-tier mold in which crystals having a cross section of 1/8, 1/4, and 1/2 in. were grown from a common seed. The mold design was arranged so that one 1/2-in. crystal, two 1/4-in. crystals, and four 1/8-in, crystals of the same orientation could be cast. With this technique, it was possible to obtain only one set of crystals with the same orientation. Because of this limitation, it was not possible to determine both the changes of extent and slope of the various stages since a large number of crystals of the same orientation would have been required. Instead, only the change of slope as a function of the rate of metal removal was studied by abruptly altering the current density of the electrolytic polishing bath at various strains within the regions of Stages I and 11. The experimental techniques used for the tensile studies were essentially the same as those used previously.1,3 The specimens were deformed in a 200-lb Instron tensile machine, usually at a rate of 10-5 sec-5. A methyl alcohol-nitric acid solution was used as the polishing bath for aluminum. The temperature was maintained constant within ±0.l°C by means of a water bath. The tensile machine was

Jan 1, 1963

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus ½ in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in, bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand.

Jan 1, 1950

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931

By D. L. Archer, W. W. Owens

Conventional waterflooding often is uneconomic in highly fractured reservoirs because of the gross bypassing of the reservoir oil by injected water. Imbibition and pressure pulse flooding have been used in at least one fractured reservoir in an attempt to achieve better oil recovery performance. This paper presents the results of laboratory flow tests conducted on large cores to evaluate the possible applicability of these methods (particularly pressure pulse flooding) to different types of reservoir systems. Test data were obtained on both water-wet and oil-wet systems, and on systems having two widely different levels of compressibility and flow capacity. Results indicate that pressure pulse recoveries from fractured reservoirs will likely not exceed 5 to 10 per cent pore space with maximum response achieved during the first pulse cycle. Improved recovery by this method is possible from both oil-wet and water-wet reservoirs. Comparable saturation distributions during imbibition and pressure pulse production suggest that an initial pressure pulse cycle to speed production response would not interfere with subsequent imbibition flooding in water-wet reservoirs. INTRODUCTION There is a steady increase in the number of fluid injection projects being initiated each year to improve oil and gas recovery over that obtained by primary production mechanisms. Experience gained in different geographical areas and with different recovery methods is teaching that reservoir anatomy is one of the more important factors controlling the success or failure of such projects. Fractured formations appear to be the rule rather than the exception, especially in carbonate reservoirs. Conventional methods of fluid injection, whether it is waterflooding, gas injection or miscible flooding, have limited applicability to highly fractured reservoirs because of the severe bypassing of reservoir fluids. The result is early breakthrough of the injected fluid and rapidly increasing ratios of injected to in-place fluid with an undesirable effect on return on investment. Thus, innovations to conventional methods must be developed if recovery from fractured reservoirs is to be optimized. One new method proposed for application to highly fractured reservoirs is pressure pulse waterflooding. Although pressure pulsing with gas has been suggested' and rested in at least one reservoir; the Sohio Oil Co. is generally credited with the development and testing of pressure pulsing in conjunction with waterflooding. Publications" of Sohio's waterflood operations in the Spra-berry Trend indicate that the idea for pressure pulse flooding evolved from a critical analysis of the disappointing early performance of their flood initiated in a portion of the trend in April, 1961. This flood was planned to take advtantage of imbibiltion and high pressure gradients across the reservoir matrix blocks (unfractured Mocks of the reservoir rock which are visualized to be generally surrounded 'by the fracture system) evaluated in pilot tests by the Atlantic Richfield Co.5 and Humble Oil & Refining Co.' However, the early recovery and pressure performance of this flood indicalted that high pressure gradients induced between the fracture system and the centers of the matrix blocks were forcing water into the periphery of the blocks and temporarily interfering with the counter-current flow of oil due to imbibition. Fill-up in the blocks was occurring with re-solution of the free gas phase as pressures climbed above the original reservoir bubble point. It appeared that cessation of water injection to permit the capillary forces to become dominant and that expansion of the rock and its contained fluids during pressure reduction might aid in expulsion of oil from the rock matrix into the fractures. Subsequent production performance. aflter cessation of injection, proved this hypotheslis correct. Thus, pressure pulse waterflooding was born. Pressure pulse flooding appears to have several advan'tages over imbibition type flooding in highly fractured reservoirs. First, all wells may be used for water injection which should hasten fill-up and achieve a more rapid increase in reservoir pressure. Second, because of increased injection pressures and rates, flooding gradients will force water into the reservoir matrix more rapidly than would be achieved by imbibition alone. Third, during the pressure depletion cycle of the flood, the compressibility of the system, which has been increased by resolution of the free gas phase, provides energy for the displacement of oil at a rate greater than would correspond to countercurrent flow during imbibition. Fourth, during depletion all wells may be put on production, thus contributing to higher oil withdrawal rates on a reservoir-wide basis. One possible disadvantage of pressure pulse flooding as compared to imbibition floodling, however, is that the outer periphery of each matrix block is flooded to a residual or near residual oil saturation during the Water lnjection stage. This zone of reduced permeability to oil m'ay offer greater restriction to the production of

Jan 1, 1967

By W. E. D. Stokes

WHEN history is written, the year of the blitzkrieg will go down as giving aviation its greatest impetus. No perceptible drop in military business, even with cessation of hostilities abroad, seems likely. The combined air force of the U. S. Army and Navy on July 1 was approximately 5000 planes, as against 50,000 planes currently discussed as necessary. Observers at the fronts are giving designers and metallurgists back home some realistic ideas to shoot at. As conventional runways reveal the location of airports to enemy raiders, operating bases are now masked. Difficult, often muddy and rough landing strips, requiring strong landing gears and exacting take-off and maintenance characteristics, are the specifications of war. This is "old stuff" to numerous mining operators in mountainous jungle areas where gradients up to 8 per cent are in more or less common use in such mountain landing fields. Although airplane building is not readily adaptable to assembly-line methods, a trend towards mass productions is now in evidence. Incidentally, a U.S. Army "Curtiss P-40" requires about 10,000 man hours of work to complete and is tied together with 75,000 rivets. During the past year a number of aircraft factories adopted the "shot-

Jan 1, 1941

By C. B. Manula, R. Venkataramani

Application of computers to present-day open-pit mining with bucket wheel excavators (BWE) is discussed. The development of the wheel excavators and their use in mining are discussed along with the necessity for building a computer model of the bucket wheel and the mathematical formulation of the problem. The simulation procedure, testing the model, and test results are summarized. Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the 20th century. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management, and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mold of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. Constant efforts are needed to improve upon productivity if the ore is to be economically mined. The development of vast low-grade deposits and thick overburden deposits calls for better tools to handle the enormous amount of materials. A natural solution to this problem is the use of bucket wheel excavators (BWE), which employ a continuous cutting head to feed the materials handling system. High productivity, versatility, economy of operation, and adaptability to most types of haulage systems combine to make BWE's attractive for large earth-moving operations. "Operating costs are being pushed down by the impact of giant haulage units, by high-speed conveyors, and computerized railroads. Matching all these with the continuous output of BWEs, one can visualize increased production at much lower costs." Historical Background The wheel excavator, which was patented in Germany in 1913, made its first appearance in an open-pit lignite mine in 1920. From this early beginning, however, BWEs were slow coming into practice. Initial developments were dampened by many design problems. From 1936 onward, major developments in design improved the wheel's ability, capacity, and versatility. A literature survey shows that wheel excavators are being used in Australia, Zambia, South Africa, the Congo, India, Indonesia, Czechoslovakia, Russia, Great Britain, Guyana, Yugoslavia, Morocco, Germany, Canada, and the U.S. for mining and loading chalk, lignite, clay, sandstone, phosphate, broken ore of iron, coal, shale, loose and semi-loose rock overburden.' A recent LMG* BWE at work in a German lignite mine weighs 6790 tons with an hourly capacity of 11,000 cu m. Although the BWE has wide applicability, its application to new mining areas poses a problem. Because of the large capital investment involved in BWE application and the narrow profit margins in mining low-grade ores or coal at depth, little margin of error can be tolerated in the selection, design, and operation of these machines. The questions that need to be answered prior to installation of a BWE for a mineable deposit are: 1.) What are the anticipated BWE performance characteristics? 2) Which method of BWE operation is most efficient? Attempts to answer these questions require a thorough knowledge of the mining system and the BWE operation. One approach is the building of a computer-ori-ented simulation model to determine how information and policy create the character of the BWE system under consideration. BWE Operation Modern BWEs generally excavate in blocks. Fig. la shows a BWE working in an established cut. The wheel is positioned to travel on the pit floor in line with the top edge of the old highwall. As it advances, a new highwall is exposed in the direction of excavation. Digging is done by rotating the wheel, swinging it from side to side in long parallel arcs, and "crowding" into the bank, by advancing the entire machine, or by the travel of the digging boom if an automatic crowd is available (Fig. lb). A second way by which the wheel can be advanced into the bank is by the falling cut method. A brief description of each of these methods follows. Cut with a Crowding Machine: At the end of every swing, the digging boom can be extended by the thickness of cut desired and the boom swung back in the reverse direction. Obviously, the thickness of bank excavated does not vary with the boom position; therefore, the slewing motion of the boom is fairly constant for uniform output. The thickness through which the digging boom can be advanced into the bank is theoretically calculated from the formula'

Jan 1, 1971

By John C. Martin

The discovery of a new gas reservoir demands that the planning of a sottnd well-spacing program be initiated early in the development stage. It is the purpose of this discussion to illustrate by actual field examples the application of basic well-spacing principles, previously developed for oil reservoirs, to the problem of well spacing in natural gas fields. These studies are presented for the field use of geologists and engineers who are concerned with the initial planning of the proper development of the newly discovered gas reservoir. INTRODUCTION The phenomenal growth of a vigorous natural gas industry emphasizes the increasing importance of natural gas as a source of energy, fuel, and raw materials to our nation's economy. Since 1945 marketed production of natural gas for the U. S. has increased 21/2 times to a record high of 10.6 trillion cu ft during 1957. As major participants in the gas industry, we share an added interest to develop and produce our natural gas reserves with constantly improved efficiency. The subject of well spacing is vitally important to the gas industry, for the well itself plays a significant role in the development of the natural gas reservoir and in control of the recovery process. Maximum utilization of wells is an integral part of sound conservation practices. The discovery of a new gas reservoir demands that careful choice of well location and well spacing be made and that the planning of a sound well spacing program be initiated early an the development stage. With the drilling of the first development well, efforts of the geologist and engineer must be directed toward acquisition of adequate technical evidence upon which a firm recommendation for a spacing program may be based. With this technical appraisal as a foundation, operators and state regulatory agencies jointly can go far in providing a framework for sound development of gas fields to achieve a program of conservation that avoids the unnecessary well. WELL-SPACING CONCEPTS Through laboratory and field investigations of the mechanism of the recovery of oil and gas, of fluid behavior, and of effective control of reservoir and well, a crystallization of ideas regarding reservoir behavior has emerged as a well-developed technology. Associated with a better understanding of the fundamental principles underlying reservoir and well behavior has been the growth of concepts concerning the role of wells and their spacing in the development and operation of an oil or gas reservoir. In addition to serving as outlets for the withdrawal of fluids from the reservoir, wells are recognized as having two other important functions: (1) providing access to the reservoir to obtain information concerning the characteristics of the reservoir and its fluids, and (2) serving as a means by which the natural or induced recovery mechanism may be effectively controlled. Beyond a minimum number of wells required to fulfill these two functions, additional wells will not increase recovery. With particular emphasis upon well spacing in oil reservoirs, many studies of the well spacing-recovery relationship have evolved the concept that the ultimate oil recovery is essentially independent of the well spacing.' These fundamental concepts are no different when regarding the role of wells and their spacing in the natural gas reservoir. They are equally applicable to the consideration of well spacing in gas reservoirs. For the gas reservoir, the problem of well spacing then revolves around the question of drainage and the degree or extent to which a well may drain gas from its surrounding reservoir environment. Theoretical and Experimental Work During the past 30 years, theoretical and experimental work carried on to study the physical principles involved in the flow of fluids through porous media has shed light upon the matter of drainage. Fundamental mathematical equations have been derived to describe the mechanism of flow of oil and gas through porous rocks. With the recent advent of high-speed digital computers, attempts have been made with mounting success to develop solutions, employing numerical techniques, to mathematical expressions that describe more rigorously the physical behavior and mechanism involved in the unsteady-state flow of compressible fluids, such as a gas, through porous rock. In 1953, Bruce, Peace-man, Rachford and Ricez published a stable numerical procedure for solving the equation for production of gas at constant rate. The results of these calculations are significant with respect to this matter of drainage, for they indicated (1) that depletion of the gas reservoir resulted in a drop in pressure at the extremity of the

By W. R. Hibbard, Ming-Kao Yen

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By L. K. Eigenbrod, F. Notaro

Enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969) has placed new responsibilities on the mining industry. The new law, aimed at eventually solving the problem of pneumoconiosis, sets new respirable dust standards at 2 mg per cu m. Techniques employed to date have been shown to lack total effectiveness in meeting the prescribed standards. Since it is possible that even the new standards will eventually have to be lowered to effectively attack the medical problem, the need for new and more reliable methods of assuring clean respirable air will intensity. This paper presents, in a preliminary manner, both the present technical capability and growth potential of cryogenic technology for supplying miners with clean breathing air. Work with two sizes of prototype supplied-air (cryogenic-liquid) respiratiors in Union Carbide&apos;s Fawn Coal mine, will be described. Other potentially fabricable systems will be discussed and a preliminary assessment made of the potential cost of introducing cryogenic air breathing systems in coal mine service.

Jan 1, 1972