Search Documents

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By J. B. Clemmer, W. L. Lennemann, J. B. Rosenbaum

Security restrictions on processing uranium raw materials to yellow cake were lifted in August 1955, coincidental with the Geneva Conference on Peaceful Uses of Atomic Energy. Numerous reports and technical papers on uranium extraction and recovery methods have appeared since that time, and it is doubtful that another review of past and current practices would add much to the technical literature. Development of some promising procedures was arrested, perhaps temporarily, by mechanical handling problems or peculiarities in the chemistry of uranium and associated elements. Some methods have been incompletely evaluated and still others that tested well in the laboratory and pilot plant are dormant because of competition from other processes, or because of their restricted applicability to particular ore types that have not reached quantity production. In view of the vast number of new ideas and procedures that have been advanced, considered, and tested, it would be futile to attempt a comprehensive survey in this article. Only a cross section of the field, based on random sampling, can be provided here. The authors have chosen, therefore, to discuss some innovations that may provide a clue to uranium ore processing techniques of the future. An effort has been made to select unpublicized new metallurgical techniques or interesting applications of established principles and procedures. With the two exceptions noted later, all the research to be described has been sponsored by the AEC. Physical Beneficiation: Individuals and firms engaged in mining and processing uranium ores, and in related research activities, have often had considerable experience in ore dressing. As might be expected, therefore, a prodigious amount of work has been done on physical beneficiation testing of uranium ores, particularly in efforts to concentrate subgrade materials. Although some success has been attained on specific ores by gravity concentration and flotation, ratios of concentration have generally been low and there has been difficulty in making a throwaway tailing.

Jan 9, 1957

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

By Edna A. Dancy, Ronald L. Pastorek, Gerhard J. Derge

In an earlier study1 in this laboratory, it was found that there is a minimum in the specific conductance of Ni-S melts in the region of the stoichiometric composition, Ni3S2. This and similar observations on other sulfide1 and telluride2 systems suggest that short-range order exists in the molten phase for several hundred degrees above the melting point, and a qualitative energy-band model has been proposed, with intrinsic semiconduction at the stoichiometric composition and degenerate electron and hole conduction at metal- and tellurium-rich compositions. This suggestion has been substantiated for the telluride systems by Seebeck coefficient measurements which showed a change in sign from negative on the metal-rich side to positive on the tellurium-rich side. In the present investigation, in order to substantiate still further the proposed model, Seebeck coefficient determinations have been extended to the Ni-S system over a composition range in the vicinity of Ni3S2. The experimental method was essentially the same as that used for the telluride systems, with minor modifications on cells for high sulfur melts to permit the use of tungsten wires and W— W-Re th~rmocouples instead of the chrome1 or alumel wires and chromel-alumel thermocouples originally used. Chrome1 and alumel both deteriorate very rapidly in atmospheres containing sulfur. The Ni-S alloys were prepared as described in the conductivity paper. Initially, a portion of the solidified melt was analyzed at the end of a run, but after this was found to be inaccurate because of segregation during cooling, the whole sample was analyzed. The nickel content, only, was determined, the sulfur content being obtained by difference. The results are summarized graphically in Fig. 1, and clearly show a change in the sign of the Seebeck coefficient in the region of the stoichiometric composition. This change of sign near Ni3S2, coupled with the minimum in the conductivity, is suggestive of an intrinsic semiconductor at the stoichiometric composition, with degenerate electron and hole conduction on either side of this composition, in keeping with the proposed model. The negative temperature coefficient of conductivity, normally indicative of metallic conduction, is not inconsistent with this model. In the completely degenerate region it would be expected, while in the vicinity of Ni3S2 the suggestion originally made by Argyriades, Derge, and pound3 for the Fe-S system can probably be applied. They proposed that the forbidden gap between the valence band and the conduction band is small, and that the increase in the number of the conducting species with increase in temperature is not large enough to compensate for the loss of mobility through thermal scattering. The research was sponsored by the Office of Naval Research under Contract NONR-760(22) Project NR 039-081. 'E. A. Dancy and G. J. Derge: Trans. Met. Soc. Aime, 1963, vol. 227, pp. 1034-38. 'E. A. Dancy: Trans. Vet. soc. AIME. 1964, vol. 233, pp. 270-77. 'D. Argyriades, G. Derge, and G. M. Pound: Trans. Met. Soc. . 1959, vol. 215, pp. 909-12.

Jan 1, 1965

By J. B. Mackintosh

THE quantitative determination of copper, by means of electro-deposition, offers so many advantages, that it is to be preferred, when properly executed, to all other methods for ease and accuracy. The object of the present paper is to give the results of a number of experiments made during the past few months, and to indicate some sources of error, which must be avoided in order to attain the necessary accuracy. In 1867, C. Luckow, in competition for a prize offered by the directors of the Mansfield Copper Works, submitted the following

Jan 1, 1882

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950

By P. Pietrokowsky, T. E. Tietz, J. E. Dorn

The amount of solid solution hardening in aluminum alloys was found to be dictated by two factors: the lattice strain, and the change in the mean number of free electrons per atom of the solid solution. To obtain this correlation it was necessary to assume that aluminum contributes two electrons per atom to the metallic bond. WHEN the modern scientific method of analysis was first being formulated, Francis Bacon recorded in his "Essays" (circa 1600) that "an alloy . . . will make the purer but softer metal capable of longer life." During the intervening centuries voluminous data have been reported which demonstrate that the additions of alloying elements do in fact increase the hardness and strength of the pure metals. Nevertheless, the significant details of this problem on the unique effect of each element toward enhancing the mechanical properties of alloys only recently have been subjected to systematic scientific scrutiny. The major objective of this investigation is to determine how minor additions of alloying elements affect the plastic properties of polycrystalline aluminum alloys. By means of such studies it is hoped to provide not only data on the solution strengthening of aluminum alloys, but also a body of facts which will supplement the knowledge already available on the factors responsible for solution hardening in general. A review1"10 and analysis1' of the existing data on the effect of solute elements on the plastic properties of solid solutions reveal that our current knowledge on solid solution hardening is somewhat meager, inconsistent, and inconclusive. Many of the inconsistencies are undoubtedly attributable to the influence of unsuspected factors, such as purity; or uncontrolled factors, such as grain size, on the plastic properties of alloys. Nevertheless the following conclusions might be tentatively accepted: 1. Addition of solute elements invariably increases the yield strength, tensile strength, and hardness of the host element. 2. The rate of strain hardening, in general, increases with the concentration of the alloying element. 3. The strengthening effect in ternary alloys is the sum of the individual strengthening effects of the two solute elements as measured in their binary alloys. 4. The lattice strain is one factor that affects the strengthening of the alloy but it is not the only factor. 5. A second factor might be the difference in valence between the solute and solvent metals. All of the available evidence is in complete agreement with the first conclusion; the remaining conclusions, however, are not in agreement with all of the published data, but, in each case, the major weight of the existing evidence favors these deductions. Additional investigations will be required before most of these tentative conclusions can be accepted without reservation. In the following report an extensive investigation of the plastic properties of binary aluminum alloys is described. This work was undertaken in an attempt to shed more light on the general problem of solid solution hardening. Materials for Test: Aluminum was selected as the solvent metal for the present investigation on the effect of solute elements on the plastic properties of alloys. This choice was made for several reasons: (1) There appears to be little fundamental data in the published literature on the effect of solute elements on the properties of high-purity aluminum alloys. In view of the ever increasing economic importance of aluminum, such data would be of basic interest to the metallurgists concerned with the development of new aluminum alloys. (2) Aluminum is thought to be only partially ionized in the metallic state1' and consequently it might provide more complex relationships of the mechanical properties with the concentrations of the solute elements than more simple fully ionized solvents would reveal. (3) The data on aluminum alloys will provide a broader basis for correlations between the mechanical properties of metals in general and the concentration and atomic properties of the solute elements than is now available. Some complications, however, attend the selection of aluminum: The solubility of the various elements in the alpha aluminum phase are quite restricted, and not always well known. Consequently, only dilute solid solutions are available for study. This, however, may be somewhat advantageous because the dilute solution laws presumably are simpler than those applying to concentrated solutions. In addition, strain-hardened pure aluminum is known to recover at atmospheric temperatures. Very likely its alloys exhibit slower recovery rates. Thus, the secondary factor of effect of alloying elements on recovery might complicate the data. Such compli-

Jan 1, 1951

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By D. B. Hunter, H. W. Rosenberg

The titanium-rich portion of the Ti-Pd system was investigated from 0 to 75 wt pct Pd by metallo-graphic and X-ray techniques. A 0 eutectoid occurs at 24 wt pct Pd and 1190°F. Two compoutzds are indicated in the region below 75 wt pct Pd, Ti,Pd and Ti2Pd3. The solubility of palladium its a titanium is low, probably less than 1 pct. In 1960 Rudnitskii and Birunl published a complete version of the Ti-Pd phase diagram. However, their work was in disagreement with the earlier literature in that they reported only one inter metallic compound, whereas three had been reported earlier. In view of these discrepancies, it was therefore necessary to redetermine those portions of the diagram of immediate interest. The following account describes our work on the system over the range of 0 to 75 wt pct Pd. MATERIALS AND METHODS Distilled titanium sponge and elemental palladium were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 10 to 50 g blended compacts that were melted into buttons by arc melting under gettered argon on a water-cooled copper hearth. Weighing of the ingredients before and after melting showed that negligible weight changes occurred. Therefore, no analyses were undertaken and the compositions of all alloys are nominal. All alloys were fabricated by hot rolling at 1700°F to 0.070-in.-thick sheet. Scale was removed by sandblasting and pickling in a 5 pct HF-35 pct HNO,, balance H20 solution. For metallographic examination, specimens were mounted after heat treatment transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and then electro-polished using a solution containing 600 ml me-thanol, 60 ml perchloric acid, 360 ml butyl cello-solve, and 2 ml "Solvent X". Unless otherwise specified, etching of alloys containing up to 42 pct Pd was carried out by swabbing with a 12 pct HN03-1 pct HF aqueous etch where a bright etch was required, or by a 1 pct hydrofluoric in saturated oxalic acid solution where contrast between phases was required. The Ti-52.8 Pd alloy was etched with a solution of 25 ml HF, 40 ml glycerine, 35 ml methanol, and 18 g benzalkonium chloride. For X-ray examination, 1/2-in.-square speci- mens of sheet were mounted flat in a standard 1-in. metallographic mount and ground and polished as above. X-ray diffraction was performed using a Norelco type 12045 Diffractometer, employing CuKa radiation with a nickel filter at 40 kv and 20 ma. Specimens were rotated about the sheet normal during exposure. Although this procedure did not remove the effects of sheet texture from the relative intensities, it had the advantage that oxidation or contaminants entering during preparation of powder samples could not confuse the patterns obtained. RESULTS AND DISCUSSION Fig. 1 illustrates the Ti-Pd phase diagram according to Rudnitskii and Birunl with the work of the present authors superimposed. Both interpretations agree that the system is of the 0 -eutectoid type with an extensive 0-phase field, and that the eutectoid temperature is just below 1200°F. There is also agreement that the solubility of palladium in a titanium is restricted. Our work would indicate that the a solubility of palladium is low, probably less than 1 pct. However, whereas Rudnitskii and Birunl place the eutectoid composition at 41 wt pct Pd, this investigation shows it to be at about 24 wt pct Pd. Moreover, this investigation confirms the existence of compounds at Ti2Pd and Ti2Pd3, whereas Rudnitskii and Birun report only a single Berthol-lide phase covering the TiPd to TiPd, range. Laves et a1.' and Wallbaum, whose work was summarized by Maykuth , reported the existence of Ti2Pd3 and TiPd, in addition to Ti2Pd. More recently, Nevitt and Downe~' have reported the structure of

Jan 1, 1965

J. W. Tomlison—It seems probable that the author's conclusion, that the conductivity of the slags decreases with increasing content of FeO, is erroneous due to the method of plotting the data. Thus, the results of other workers2,3,13,15 show that the conductivity of molten oxide slags increase with increasing temperature, indicating that the trend of the curve shown by the authors is due to the fact that the data for the slags containing relatively small amounts of FeO are at higher temperatures than those for the slags containing relatively large amounts of this oxide. In this connection the work of Wejnarth2 may be mentioned in which in an investigation of a series of iron silicate slags, the conductivity was found to increase with increasing content of FeO; the fact that the author's slags contained TiO2 probably does not affect the issue since it has been shown15,16 that, at least as far as conductivity is concerned, this oxide behaves essentially the same as silica and that mixtures of the oxide with silica have a very low conductivity of the order of 10-4 mhos at 1750°C. In connection with the experimental technique it may be noted that bubbles of carbon monoxide would probably be produced at the surface of the graphite electrodes in contact with the melts thus rendering the accuracy of the measurements somewhat open to question. J. L. Wyatt (author's reply)—Dr. Tomlinson makes reference to works by Martin and Derge, which indicate that slag systems containing no TiO2 are characterized by an increase in conductivity with an increase in temperature. Further, I have cited his examples, which indicate a drastic increase with small temperature change. The results of Dr. Derge's work have no bearing whatsoever on the results of this paper, since the slags under study here contained up to 70 pct TiO2 One cannot generalize on slag systems as a whole on the basis of any one family, for there are definite compounds of ionic nature formed in each system, and the ionic mobilization of these is something that cannot be determined without actual experimentation. Dr. Tomlinson makes reference to an unpublished work which, he claims, shows that titanium dioxide behaves the same as silica in regard to conductivity. Since I have not had 'an opportunity to see the paper I cannot make any comments, but unless the same slag system was studied there can be no specific comparison of results. If the decrease in conductivity of the slag was due entirely to temperature phenomena, as Dr. Tomlinson indicates, then one is without an explanation of the values shown in the paper for slags containing from 10 to 20 pct FeO. I cannot agree that the deviation in findings was appreciably related to temperature change; further, I believe this point was completely covered in the paper. References 13 Endell and Hellbrügge: Glasstech. Ber. (1942) 20, 277. 14 Bockris, Kitchener, Ignatowicz and Tomlinson: Faraday Society. Discussion (1948) 4, 265. 15 Tomlinson: Thesis, London 1949. 10 Bockris, Kitchener, Ignatowicz, and Tomlinson: Unpublished work.

Jan 1, 1951

By R. V. Whetsel, V. R. Gargias, J. W. Ristori

WoRld consumption of petroleum and its substitutes in 1941, the amount of which obviously is largely conjectural, is estimated at 2,066,653,000 bbl. This is 48,689,000 bbl. more than the previous year and is an all-time high. Except for the United States, this figure does not include consumption for military purposes. Consumption in the United States also reached an all-time high during 1941, totaling 1,492,000,000 bbl., or 158,230,000 bbl. more than the previous peak year of 1940. On the other hand, it is estimated that civil consumption in countries outside of the United States decreased 109,541,ooo bbl. as compared with the previous year. Demand for military purposes and/or additions to stocks in countries outside of the United States is estimated at 304,507,000 bbl. during 1941, compared with 209,635,000 bbl. in 1940. This increase was due largely to blitzkrieg warfare on several fronts. especially Russia; entailing large expenditures of petroleum by both sides because of the immense area covered by the fighting forces, the long supply lines necessary and the intensity of the fighting. It is interesting to note in this connection that Axis-controlled countries, excluding Japan, had an estimated production of approximately 89,000,000 bbl. of petroleum and its substitutes in 1941. The peacetime consumption of these countries in 1938, for example, was about 183,000,000 bbl. It is believed that the minimum to which civil consumption could possibly be re-duced in wartime is 20 per cent of that of peacetime, which would call for a minimum consumption of 37,000,000 bbl. in these countries in 1941 for civil purposes. This

Jan 1, 1942

By V. R. Gargias, J. W. Ristori, R. V. Whetsel

WoRld consumption of petroleum and its substitutes in 1941, the amount of which obviously is largely conjectural, is estimated at 2,066,653,000 bbl. This is 48,689,000 bbl. more than the previous year and is an all-time high. Except for the United States, this figure does not include consumption for military purposes. Consumption in the United States also reached an all-time high during 1941, totaling 1,492,000,000 bbl., or 158,230,000 bbl. more than the previous peak year of 1940. On the other hand, it is estimated that civil consumption in countries outside of the United States decreased 109,541,ooo bbl. as compared with the previous year. Demand for military purposes and/or additions to stocks in countries outside of the United States is estimated at 304,507,000 bbl. during 1941, compared with 209,635,000 bbl. in 1940. This increase was due largely to blitzkrieg warfare on several fronts. especially Russia; entailing large expenditures of petroleum by both sides because of the immense area covered by the fighting forces, the long supply lines necessary and the intensity of the fighting. It is interesting to note in this connection that Axis-controlled countries, excluding Japan, had an estimated production of approximately 89,000,000 bbl. of petroleum and its substitutes in 1941. The peacetime consumption of these countries in 1938, for example, was about 183,000,000 bbl. It is believed that the minimum to which civil consumption could possibly be re-duced in wartime is 20 per cent of that of peacetime, which would call for a minimum consumption of 37,000,000 bbl. in these countries in 1941 for civil purposes. This

Jan 1, 1942

By James Howard

ON Aug. 25, 1911, a rail failed on the Lehigh Valley Railroad, causing a disastrous wreck. The surface of the fracture was in a plane at right angles to the length of the rail. There was a dark-colored, oval spot on this surface, located on the gage side of the head, representing the part of the rail which was the first to fracture. The nucleus of this spot showed that the fracture had an interior origin. Other fractures of this kind, the peripheries of which had not reached the surface of-the rail, presented surfaces having a silvery luster. The darkened surface of the present fracture was caused, doubtless, by the air having had access to it. This fracture was recognized as a fatigue fracture, of a modified type, its interior origin having been due to a component in the rail which is not usually present in cases of fatigue fractures. The metal next the running surface of the head of the rail was in a state of internal compression, this being the component not commonly met with in other cases, and which caused the fracture to have its interior origin. For the purpose of giving this modified type of fatigue fracture a specific name, for identification, the term "transverse fissure" was applied. No mystery was thought to attach to its formation, or to its development. The explanation of its occurrence was obvious in the light of common knowledge upon the behavior of steel under repeated alternate stresses. By reason of the state of internal compression at the running surface, the maximum tensile stresses in the head, under bending loads, were along an interior element. Here the tensile strains were higher than in the fibers more remote from .the neutral axis. Under such conditions the fracture of the rail would be expected to have an' interior origin. A discussion of the subject of transverse fissures essentially becomes a discussion of fatigue fractures, since they are identical. The descriptive term employed, merely for the identification of this type of fatigue fracture, had the appearance of creating alarm. Apprehensions arose that a new phenomenon in the physical properties of steel had presented itself, the explanation of which was sought in every

Jan 11, 1917

By Christer Danielsson, Sven Ivarsson

In 1951 the first ton of iron was shipped from West Africa; ten years later the total export exceeded 4 million tons, and an optimistic forecast for 1970 indicates a production capacity of something around 40 to 50 million tons. The quality of the ore varies from normal hematitic concentrates, through naturally enriched hematitic direct shipping ores with comparatively high content of ore fines, to dense, hard, rich lump ores of magmatic character. West Africa is largely composed of folded Pre-cambrian rocks trending generally northeast to southwest. They are exposed over about one third of West Africa and are part of the vast continental plateau which has an average elevation of about 1300 ft in this area.

Jan 3, 1963

By Jennings S. Cox

The following notes, prepared in 1908, as the result of a personal examination and extensive explorations under my direction in 1906, have been revised and greatly augmented after two subsequent visits and further explorations in 1910. The hard iron-ores of the south coast of Oriente Province, in the island of Cuba, have been known for many years, in fact one mine has been in operation for more than 20 years; but it is only within the past four years that the large mantle-deposits of brown ores of the north coast have attracted serious attention. A. C, Spencer' has described these ores in a paper, entitled Three Deposits of Iron Ore in Cuba, which refers to the Mayari, Moa, and Cubitas deposits. C. M. Weld,2 in a scholarly paper, The Residual Brown Iron-Ores of Cuba, has discussed the character and possible genesis of these deposits with particular reference to the Moa field, calling attention also to the Taco and Navas fields in addition to those described by Spencer. Descriptive articles with reference to the Mayari field, and a few words about the Moa deposit, have also appeared3 It is the purpose of the present paper to give some account of the exploration of the Moa deposit arid to call attention to its commercial importance. Location. The Moa district is situated on the north coast of the Province of Oriente, which is the most easterly province of the

Jan 1, 1912

The production of Rumania for 1937 amounted to 54.142.600 bbl., which is a decrease of 10.319.636 bbl., or 15.9 per cent over that of 1936. In all. 1.300.000 ft. were drilled during the year— an increase of 220.000 ft. over 1936.

Jan 1, 1938

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach's results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K' = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By H. M. Morse

Mississippi, during the year 1941, experienced the greatest diversity of oil activity since the beginning of oil interest in the state—core tests for exploration, core tests for sulphur, continued drilling at Tinsley for production, and wildcatting, which brought to light two new oil fields and two new salt domes. There were 45 wildcat wells drilled in 1941, which showed greater results and findings geologically than the 85 drilled in 1940. Tinsley Oil Field (Yazoo County).—The Tinsley oil field, with its boundaries fairly well defined now, is 8 miles long and 3 miles wide at its widest point. During the past year 213 producing wells were completed, which brought the total number of producers in the field by the end of 1941 to 325 wells. Seven producing sands have been logged, with a total average thickness of 30 ft. of oil sand. The producing formations are the Selma, Eutaw and Tuscaloosa. The average total depth of the wells is 5012 ft. The average gravity of the oil is 35.4°. Production for 1941 was approximately 15,500,000 bbl. of oil. Vaughan-Pickens Oil Field (Yazoo County).—At the end of 1941 only three wells were Producing in this field, the fourth having been abandoned. The total production for the field for the year was approximately 250,000 bbl. of oil. The producing sand is the Wilburn, in the Eutaw formation. Cary Field (Sharkey County).—The British American Oil Producing Co. completed, on Sept. I, 1941, its F. B. Houston No. A-I well, sec. 23, T. 11 N., R. 7 W. It is

Jan 1, 1942

By H. M. Morse

Mississippi, during the year 1941, experienced the greatest diversity of oil activity since the beginning of oil interest in the state—core tests for exploration, core tests for sulphur, continued drilling at Tinsley for production, and wildcatting, which brought to light two new oil fields and two new salt domes. There were 45 wildcat wells drilled in 1941, which showed greater results and findings geologically than the 85 drilled in 1940. Tinsley Oil Field (Yazoo County).—The Tinsley oil field, with its boundaries fairly well defined now, is 8 miles long and 3 miles wide at its widest point. During the past year 213 producing wells were completed, which brought the total number of producers in the field by the end of 1941 to 325 wells. Seven producing sands have been logged, with a total average thickness of 30 ft. of oil sand. The producing formations are the Selma, Eutaw and Tuscaloosa. The average total depth of the wells is 5012 ft. The average gravity of the oil is 35.4°. Production for 1941 was approximately 15,500,000 bbl. of oil. Vaughan-Pickens Oil Field (Yazoo County).—At the end of 1941 only three wells were Producing in this field, the fourth having been abandoned. The total production for the field for the year was approximately 250,000 bbl. of oil. The producing sand is the Wilburn, in the Eutaw formation. Cary Field (Sharkey County).—The British American Oil Producing Co. completed, on Sept. I, 1941, its F. B. Houston No. A-I well, sec. 23, T. 11 N., R. 7 W. It is

Jan 1, 1942