Search Documents

By N. D. Policow, J. S. Orphanos

Dewatering fine clean coal fractions, -595µm (-28 mesh), represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the screen bowl centrifuge has offered an economical alternative to filtration/thermal dyer combinations. The performance of screen bowl centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Test comparisons with alternative methods show the screen bowl centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1984

By S. N. Dixon

Sampling and assaying procedures were developed to obtain unbiased and reasonably accurate Au grade estimates in drill samples fm a coarse gold deposit. Gold grade comparisons were made by assaying 3 (1 assay ton) splits from each drill interval, then processing the entire reject thru a pilot plant for a blocked out zone. The result comparing the assay splits to the pilot plant results gave a ratio of 1 to 1.07. Another technique was developed to detect drill samples which has a coarse gold content by monitoring the varience. Testwork could be done on a 1 kg sample to improve the accuracy of the grade estimation if the variance was high for a drill interval.

Jan 1, 1984

By R. Hogg

The mathematical description of solids transport in mills is an important aspect of the development of comprehensive models for the analysis, simulation and control of grinding systems. The basic mechanisms of particle transport and mixing, including gravity flow, carrier fluid transport, and "diffusion", are reviewed and their relative importance in wet and dry ball mills is discussed. Specific models for transport and mixing in dry, grate-discharge and wet, overflow ball mills are described. The limitations of the models, parameter estimation problems, scale-up criteria etc. are discussed and the conditions which lead to particle size dependent transport, and hence to internal classification in the mill, are described in detail.

Jan 1, 1984

By D. R. Maneval

The Surface Mining Act of 1977 required a study by the National Academy of Sciences regarding the special mine reclamation requirements of Alaska. The status of mines operating and planned in Alaska will be presented. New mines opening in Alaska must establish a baseline inventory of plants and animals in the mine site area as well as determine pre-mining air and water quality. Current work in these areas will be summarized. Reclamation practices in Alaska and other Arctic countries as practiced currently will be described. A summary of current research in Alaska dealing with revegetation on surface mined lanais, re-establishment of animal populations, and water treatment processes necessary in this pristine environment will be discussed. Included will be future predictions of the direction of mine reclamation in Alaska as more mines enter the industry.

Jan 1, 1984

By I. A. Violic, L. D. Cruz, M. A. Solari

In Exxon's Los Bronces Expansion Project in Chile, a stochastic simulation is performed to resolve the complex decision problem of matching the mine to mill system capacities from both technical and economic standpoints. The unique combination of weather conditions at the mine and the 30-km (18.6 mile) belt conveyor network for ore transport to the mill necessitates this analysis in the planning phase to optimize the design capacity of the system. Appropriate statistical distributions of major equipment performance, snow storm duration, power outage, etc., are developed from actual mine local records and manufacturers' specifications. The interactions of operational constraints including ore storage capacities, number and sizes of individual equipment, ore variations, and mine and mill production rates are studied more realistically than in a traditional planning approach. Details of the computer modeling and typical results of simulation studies are discussed.

Jan 1, 1984

By H. Jehn

Like some other Pt-group metals palladium shows a low but considerable solid solubility of oxygen, which was found already from oxidation studies. The oxygen solid solubility of palladium in equilibrium with gaseous oxygen has been investigated at 900 - 1300 °C in oxygen (665 mbar) and air by gassing and analyzing polycrystalline samples. The 0-concentrations range from 40 to 90 ppm and decrease with rising temperature. The isobaric solubility can be represented by the least-squares fit log c0 = 0.5 log p02- 0.32 + 920/T (c0 in wt. ppm, p02 in mbar, T in K). The thermodynamic data of the exothermic solution reaction are calculated to ?H°= -17.6 kJ?mol-1 and ?S° -76.5 J?mol ? K-1. The behaviour of palladium in an oxygen atmosphere is characterized by the simultaneous reactions of the solution of oxygen in the metal and the formation and evaporation of volatile oxides besides the pure metal evaporation.

Jan 1, 1984

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By K. A. Olsson

The Glenharold mine is a multiple seam dragline operation where many different stripping methods are employed. This paper describes the production operations of over-burden removal, coal loading, and haulage. Emphasis is placed on the methods used to uncover fie seam using draglines, scrapers, and a small shovel.

Jan 1, 1984

By P. L. Hofmann

The National Waste Terminal Storage (NWTS) Program was established in 1976. The objective of this program is to develop the technology and provide the facilities for the safe, environmentally acceptable isolation of civilian- and defense-related, high-level and transuranic nuclear wastes, including spent fuel elements, for which the federal government is responsible. The principal emphasis of this program is on disposal in mined geologic repositories. Technology development in support of the NWST program includes the formulation and management of a strong basic science and engineering program to generate an appropriate data base to aid in understanding of the key geological processes and major engineering structures involved. The current status, problems, and future plans of the technology program will be summarized.

Jan 1, 1984

By Thiann R. Yu, William J. Quesnel

At Kidd Creek, the annual production of 4.5 million tonnes of ore has been achieved primarily with sublevel blasthole stoping. This mining method has allowed underground operations to meet the designed production capacity while maintaining an outstanding safety record. To achieve this goal, rock mechanics principles have been integrated into each facet of mining in the planning stage, in the production stage, and in various stages of ground support. This paper evaluates the two adopted mining sequences based on ground stress patterns, blasting control, ground reinforcement, backfill support, and numerical modelling for stope stability at the mines.

Jan 1, 1984

By Mourad Aissa

From our previous work (Gardner, Aissa, and Verghese, 1982) on determining the residence time distribution of ball mi 11s from radiotracer data taken in closed-circuit operation without interruption of the process, it occurred to us that the data taken for this purpose also contained information on the breakage rates of all the sizes present. It is the purpose of the present work to evaluate methods to obtain breakage rates from this data. A numerical solution for the impulse injection and subsequent detection of radiotracer in a closed-circuit linear comminution process is developed and used with typical breakage parameters, residence time distribution, and classifier functions to study and evaluate these methods.

Jan 1, 1984

By G. K. N. S. Subasinghe

An attempt has been made to explain the behavior of a pinched sluice in terms of the established theories of fluid mechanics and mineral processing. A method has been developed to calculate the underflow discharge by assuming a logarithmic velocity distribution and free gravity fall through the discharge slot. The concentration profile of solids over the depth of flow has been shown to comply with Bagnold's theory of dispersive shear, rather than turbulent sediment transfer. Even although the results can be explained qualitatively by the Bagnold theory, their complete quantitative analysis will not be possible until more work is done. Consequently, an empirical equation has been developed to predict underflow pulp densities. It has been shown that the process of the segregation of the heavier mineral beneath the lighter can be described by a first order law. From the results obtained, a computer model of the pinched sluice has been developed. This predicts the underflow grade, pulp density and flow rate in terms of the feed and operating conditions. The model can also be used to determine the effect of a change in operating conditions, and for the optimization of rougher, cleaner, and scavenger circuits.

Jan 1, 1984

By Stephen C. Blair

Laboratory permeability measurements at elevated pressure and at temperatures ranging from 20º to 150°C have been conducted on samples of Ironton-Galesville sandstone. The purpose of this testing was to identify and characterize important physicochemical processes occurring in association with the injection and withdrawal of heated ground water at the U.S. Department of Energy's Aquifer Thermal Energy Storage (ATES) field site in St. Paul, Minnesota. Results indicate that permeability decreased significantly as temperature was increased and that dissolution of the dolomite and silicate cementing agents and accompanying changes in mechanical properties may occur in the heat storage aquifer at St. Paul. Further, loss of permeability with temperature in laboratory samples may be caused by the change in the mechanical structure of the sample. Tests at ambient temperature to evaluate the effect of particle migration under conditions of reversed flow indicate that this process will not significantly impair formation permeability at the St. Paul site.

Jan 1, 1984

By Michael B. Moolman

Both conventional and nonconventional process alternatives for gold recovery from cyanide heap leach solutions are discussed in terms of possible flowsheets. Conventional process alternatives include carbon adsorption and zinc dust precipitation, while nonconventional process alternatives include resin ion exchange, solvent extraction, and direct electrowinning. These strategies for gold recovery are compared on the basis of technological features and on the basis of process economics: Review of the technology status and process economics suggests that improvements for conventional process alternatives are possible and that further development of nonconventional process alternatives is warranted.

Jan 1, 1984

By J. Avraamides

Many of the current methods for producing metallic silver particles having specific characteristics involve several steps, are time consuming and subject to contamination. The novel non-aqueous chemistry of silver and copper is used in a simple two step process capable of producing high purity silver powders of specific size and shape. The chemical basis of the process involves the manipulation of the equilibrium -- Cu(I1) + Ag [=]Cu(1) + Ag(1). The addition of at least 50% (V/V) acetonitrile (CH3CN) stabilizes both Cu(1) and Ag(1) ions in aqueous sulphate medium, and the metallic silver dissolves. Removal of the volatile nitrile by distillation reverses the equilibrium and silver powder is precipitated. The nature of the powder depends on the presence of additives such as gelatin, thiourea and polyacrylamide.

Jan 1, 1984

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historic Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon-in-leach for recovery of gold from ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a coarse rock fraction from the grinding SAG mill circuit. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900's. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1984

By W. C. Meyer, R. R. Klimpel

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering mathematical models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and model predictions are presented.

Jan 1, 1984

By R. E. Sabaski

Total grinding mill system life is dependent upon the original selections and specifications of its components: the mill, its drive, drive motor, motor control, and power system. This paper discusses the complex considerations involved and the critical decisions which must be made by the buyer, the mill manufacturer, and by the gear vendor during the proposal and ordering stages. Interrelations between the mill manufacturer and the gear vendor, application of ACMA standards, how drive standards and specifications are refined through steady-state and computer-simulated torsional analyses are included, along with correlational field testing, as demands for larger sizes challenge the current state of the art.

Jan 1, 1984

By Oleg N. Tikhonov

Control of ball mill grinding circuits is important due to the enormous consumption of electrical energy in mineral processing and other industries. Optimal control requires preliminary detailed studies of static and dynamic characteristics of the process. In this paper a study of nonlinear dynamics is presented with a view toward application to automatic control and the achievement of maximum grinding rate at minimal energy consumption. The study begins with Zagustin's equation (1935) of grinding kinetics [ ]

Jan 1, 1984

Background The annual awards, which have been given by the US National Committee for Rock Mechanics since its inception in 1969, recognize out- standing research in rock mechanics. Such recognition has always been accompanied by a plaque or certificate for the winners and a presentation at the symposium awards banquet. Starting this year, the US National Committee will give the winners even more recognition and allow the rock mechanics community to benefit from the papers by publishing abstracts of the work in the proceedings of the 25th US Symposium on Rock Mechanics and in various society journals and news letters. "We hope this will stimulate the production of more research papers," said William R. Judd, former chairman on the subpanel of awards. "It's beneficial for researchers to have their work published as an award paper." There are four categories of awards: Basic Research, Applied Research, Case History, and Student Masters' Thesis. Approximately ten papers are nominated annually for each category; however, in some years awards are not made in all four categories. For instance, there were not enough case history nominations in 1983 for an award, but there were two equally outstanding recipients of the award for applied research. The winners of the 1983 research awards reflect the wide variety of professions involved with rock mechanics. They are introduced on the following pages by category, and accompanied by an abstract of the paper

Jan 1, 1984