Search Documents

By D Will

RedrossThe Redross orebody averages 1 m wide, has a strike of 50 - 350 m, dips at 55° and has a basalt footwall and an ultramafic hanging wall. The most successful and innovative aspects of mining Redross were:•ore development innovations, 90 per cent of development was split fired with a shanty back profile to enable larger and more productive equipment to be used and resulted in higher development grades, improved project payback time and improved ore recovery;•hand held stoping using a multiple level, bottom up ‘V’ shaped hand held stoping method that allowed mining on multiple levels with hand held productivities between 50 and 90 tonnes per shift;•the use of 1 m cement pillars and 7 m high crown pillars were used to create multiple mining areas that enabled high overall production rates from hand held mining this orebody; and•the use of vertical cement pillars to enable hand held mining of adjacent stopes without leaving ore pillars.MarinersThe Mariners orebody averages 3 m wide, has a strike length of 50 - 250 m and dips at 50° with a basalt footwall and poor ultramafic hanging wall. The most successful innovative ideas of re-opening Mariners were:•Dewatering the existing mine workings utilising ‘oilfield’ technology by installing a long submersible pump in on existing pump rising main. This enabled the mine to be dewatered at rates up to 100l/ sec and helped overcome the 45 to 55 L/s inflows.•Overcoming the technical problems associated with Mining N07 ore blocks which had severely deteriorated from being underwater for five years by using reverse firing techniques to improve extraction rates and reduce dilution.•Mass firing a large mining block in the N08 with minimal void space because of deteriorating ground conditions.•Use of a longhole version of the Redross hand held mining method to achieve 100 per cent extraction of the N09 higher grade lenses.

Mar 21, 2011

By J Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration in small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using e-Dev™ electronic detonators in a typical mining application was conducted at Resolute’s Mt Wright operations in North Queensland in 2010. Results were based on direct comparisons to the current industry standard of non-electric firings as a baseline, with as many parameters as possible being captured during the trial. Development costs are typically high in most underground mines, especially in capital development headings, which are in waste and therefore of no direct economic value, so by being able to accurately fire to design, costs relating to both ground support requirements and volume of material removed, (and therefore haulage required) can be minimised. A direct comparison of overbreak (ground blasted outside of design) and cast (distance rock thrown from blast) was also made during the trial, as well as close monitoring of the drilling accuracy.

Mar 21, 2011

By C Donnelly

Redpath Australia is using a unique mining method for the Australian underground coal industry at Kestrel Mine Extension in the Bowen Basin, Central Queensland.The project involves completing two separate drifts from the surface for access to the German Creek Coal Seam located approximately 230 m below the existing surface. The scope of work is primarily the construction of two drifts; the first is 1577 m at 1 in 6 gradient and the second 1874 m at 1 in 8 gradient. Each drift has been developed by a Mitsui S200 roadheader with modifications to allow for a continuous tunnelling/mining cycle operation. A shotcrete boom has been fitted to the left hand side of the machine with the operators console located at ground level. Another operators console is elevated on the right hand side of the machine to allow operation of the rotary drill boom which is mounted on a slide rail to allow flexibility of positioning depending on the stage of the cycle. In support of the roadheader activities, an integrated conveyor system mounted on a sliding floor arrangement is able to be advanced as the mining face progresses. This sliding floor consists of four 1.5 m × 6 m sections that utilise hydraulic rams to ‘walk’ inbye, allowing room for installation of precast concrete floor panels for final floor completion. This method borrows from the tunnelling and construction industries to eliminate place-change delays in the mining cycle by enabling complete ground support installation without retreat of the primary development machine from the face. The aim is to reduce the project duration with the completion of final floor and services to within 30 m of the operating face as it advances.

Mar 21, 2011

By D Beck

Open access to forecasts of mine geotechnical performance in the form of open databases of model results has been considered risky in the past, with a concern that the results will not be understood or will be misused. However, some modelling techniques allow very high similitude modelling of mine deformation and the results can be presented as deformation, damage and other parameters which are unambiguous and which all engineers can be more easily trained to understand. With some effort, sufficient reliability and quantifications of error are possible to overcome many of the issues.Allowing more members of the planning team to have direct access to forecasts of mine deformation will promote awareness of geotechnical issues and will act as a mechanism for improving mine designs. The models will also be more easily integrated into quality assurance programs, by providing a framework for understanding measurement results.The sufficiency requirements for undertaking simulation aided mining engineering will be presented, included some conclusions about requirements for training, quality standards and software development.

Mar 21, 2011

By C Hamilton

Stawell Gold Mines (SGM) is an underground mining operation located in Victoria, Australia. The mining method employed is long hole retreat stoping, utilising up and downholes and artificial concrete pillars. Stawell is currently mining the Golden Gift and Magdala orebodies.Access to the Magdala and Golden Gift deposits is via 6.0 m wide by 5.5 m high declines developed at a gradient of one in eight to one in seven from the surface to a depth of 1500 m, with a planned depth of 1650 m. From the declines, cross cutting drives are developed to intersect the orebodies. Orebodies in the Gift system are discrete lodes which are generally mined from a bottom up centre retreat to minimise geotechnical stresses.Ore development fronts are currently located between 1000 m and 1500 m below surface, with all ore being hauled to the surface using a fleet of 60 tonne underground trucks. With the use of conventional pyrotechnic long period (LP) delays, broken rock of combined ore and waste is thrown 10 m from the face and the materials hauled to the surface. The majority of the mullock from development is consumed in the underground as backfill.With the use of Orica Mining Services eDev™ Electronic Blasting System for Tunnelling, the waste is thrown up to 40 m from the face, while majority of the ore is left 5 - 10 m from the face, effectively segregating ore and waste. This enables significant recovery of gold values with minimal loss and significantly reduced dilution. By using this technique in ore drives with a 30:70 waste to ore ratio, SGM is able to haul 24 000 tonnes less mullock to the surface annually. Resue mining is applied to narrow vein headings and gives a 40 per cent grade increase at the faces as well as increasing the economic footprint of development. This will also contribute to an improved grade profile for the year from 3.98 - 4.16 g/t Au and allow extra capacity for ore haulage from stoping and for milling.This paper describes the application and the successful blast outcomes achieved using the eDev™ Electronic Blasting Systems for resue mining at SGM. Results to date, since commencement in March 2010, have been achieving significant benefits in terms of ore grade as confirmed by geologists grab sample grades. Face advance have also shown improvement with better breakage of perimeter holes giving improved face profile. These benefits are delivering increased productivity and safety performance when compared to other resue firing techniques.

Mar 21, 2011

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By D Laurence

Mining cycles have come and gone and with them there have been dramatic swings in the levels of interest and student entry into minerals-related education programs, hence graduate supply to the industry. So what is the problem? These trends will keep happening and the industry will keep on keeping on – or will it?This paper discusses recent trends in Australian minerals education programs and some international examples, together with some of the more recent initiatives taken by both the minerals education sector and the industry, such as the Minerals Tertiary Education Council (MTEC) and MEA. The real problem is that things will not just keep going the way they have over recent decades – there will come a time when there is no longer a supply of minerals academics available to provide the educational programs; and universities will simply shut down subcritical mass mining programs and invest in the much more lucrative programs such as commerce, law, medicine, etc. By the time this starts to happen it will be at least ten years too late for any last-minute reactive response by industry, if they were to try and avert such a consequence. International experience with mining programs bears out this scenario quite clearly.It is therefore timely for industry individual mines and mine management to take a much more strategic look at their role in the education sector. Sustainable mining also means sustainable minerals education – without one, the other will not function over the long-term. There is a pressing need for long-term strategic buy-in by industry into the education sector – not just for the good times, but also through the tough times. This means much more than a scholarship here or there, but includes such commitments as major industry-university research partnerships; collaborative recruitment initiatives and much more. The paper will discuss a range of such issues, problems and opportunities to address these important issues through strategic, comprehensive, long-term commitments by industry and equally significant and appropriate responses by the education sector. We care – do you?

Mar 21, 2011

By P Jones

Fosterville Gold Mine is an underground operation located approximately 20 km northeast of Bendigo and 170 km north of Melbourne. Fosterville is the most productive gold mine in Victoria, producing over 100 000 ounces of gold annually. Access to the underground is via two portals cut into previously mined open pits. Fosterville is 100 per cent owned and operated by Northgate Minerals, a gold and copper producer with mining operations, development projects and exploration properties in Canada and Australia. (Northgate Minerals Corporation, 2010).Underground operations commenced in 2006 with ore production focused on three orebodies – Phoenix, Ellesmere and Falcon. Primary ventilation to the existing operation is provided by wall mounted exhaust fans located underground. This system provides approximately 220 m3/s of primary ventilation to the operations with intake achieved through the portals. Exploration drilling during recent times has uncovered another lode, the Harrier orebody, located 2.2 km to the south of the existing workings. Due to the location of the new Harrier orebody, vent analysis revealed the requirement for a separate source of primary ventilation to service Harrier. Figure 1 shows a current underground long section and the location of Harrier in relation to the existing workings. A number of options were considered, including a parallel decline from one of the existing two portals, however, a 4 m diameter, 350 m deep surface ventilation shaft was selected as the most suitable and feasible option for the mine.In December 2009, geotechnical drilling commenced to determine the most suitable location for the shaft. Site locations were constrained by a number of factors including interaction with current and planned surface infrastructure as well as proximity to nearby community members at the southern end of the mining lease. Results from the geotechnical drilling indicated that the majority of the proposed shaft would be suitable for a 4 m raise bored shaft. However, the top 40 m of the proposed shaft were deemed unsuitable for raiseboring due to zones of weakness that would likely influence the stability of a 4 m diameter shaft (Robinson, 2010). Following independent geotechnical advice and input from experienced raiseboring contractors, it was decided to construct a 40 m presink prior to raiseboring activities.A crane mounted auger was chosen as the preferred method to construct the presink. This method differs substantially from traditional blind sinking methods which are highly labour intensive. The auger, or drill, is designed and built to be attached to a crane base using engineered pivoting cradles. The auger is suspended from the crane jib by pennant ropes attached to hydraulic rams. The auger applies rotation and axial loads to the drilling tools via a telescopic steel bar (Kelly Bar). Drill tools are attached to the bottom of the Kelly Bar and comprise an assortment of drilling buckets and reaming barrels. Drilling buckets cut in situ material and collect the spoil for removal and are used for the excavation of the ‘pilot hole’. Reaming barrels are used to expand the diameter of the excavation by directing cuttings into the pilot hole which are then removed by the drilling bucket. In June 2010, the presink was constructed utilising a crane mounted auger with support to the shaft walls applied via a remote fibrecrete unit. The excavation method involved cutting a series of smaller diameter holes (2.4 m wide) before reaming out to the final diameter (4.7 m wide) in 4 - 5 m vertical increments. Fibrecreting activities were carried out on the backshifts, to ensure the stability of the excavation and minimise interaction between the two units. The presink was completed on time and offered many advantages compared to traditional blind sinking methods, including safety, costs and timing. This paper will examine the benefits of this method as well as lessons learnt and future applications in the mining industry.

Mar 21, 2011

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

By A Reschke

The Thiess John Holland Group is undertaking the design and construction of Brisbane’s Airport Link Project, the largest single investment in transportation infrastructure in Australian history. Twin Herrenknecht TBMs are being used to bore parallel road tunnels from Kalinga Part in Toombul through to Lutwyche, a distance of 2.45 km. At 12.48 m, these tunnel boring machines (TBM) are the largest diameter machines, outside of Japan, to incorporate annular two-component type grouting through the tailskins.Grout design, preparation and injection have been given particular attention in this project in order to push the boundaries of achievement. Laboratory testing was conducted on various mix designs to ensure the contract specifi cations for grout strength could be met. To study the mechanics of the grout injection process, Herrenknecht supplied a test rig which duplicates the grout injection systems on the TBMs. Multiple recipes were tested, carefully selected to balance the requirements of rapid strength development with high mobility (to completely fill the void between the segmental lining and the ground) and minimal bleed.Team Mixing Technologies, Canada, was selected as the grout plant provider based on the technical performance of their high shear colloidal mill mixers. Field results have shown that the colloidal mixer prepared grout gives almost double the strength of an identical grout prepared by a paddle mixer.

Mar 8, 2011

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By D Wimpenny

The Bogong Power Development Project in Victoria, Australia involved the construction of a 15 m long mass concrete plug up to 9 m in diameter within the head race tunnel. The plug is critical to theperformance of the scheme as it permanently seals the head race tunnel under approximately 300 m head of water.The location of the plug in the headrace tunnel was determined by a programme of in situ rock stress testing using both hydrofracturing and over coring stress testing methods.In recognition of the importance of the plug, the Head Contract specification requires that its temperature during hydration be controlled using an embedded cooling system. In addition, contact grouting and curtain grouting around the plug cannot commence until thermal contraction was substantially complete.This paper describes the use of bespoke fi nite element software to model the temperature rise in the plug and design mitigation measures to control temperature rise in the plug. These measures include restricting the concrete placing temperature to 10°C, incorporating 39 per cent fly ash in the concrete and installing embedded cooling circuits.Site trials were undertaken to calibrate the model for the proposed concrete mix. The cooling system comprised 25 mm ID pipes forming twelve separate circuits that fed 7°C water from a single chiller unit. The cooling system reduced the peak temperature in the plug to approximately 30°C and the associated risk of early-cracking. The time before contact grouting could commence was shortened to less than two weeks from casting.

Mar 8, 2011

By P C. Miclea

Transportation networks extend every day around the world, requiring safe and well-maintained structures for efficiency and for users’ safety. Due to specific features of the infrastructure, such as longer tunnels, increased traffic and marginal safety rules, fire safety in rail and road tunnels becomes more challenging.The situation becomes more critical due to the global economy and increasing worldwide tourism, with multi-national companies often involved in both design and construction of transportation routes or systems in other countries. Tourism brings the risk of visitors becoming victims in a foreign land; thus, international law becomes more and more applicable to transportation projects all over the world, requiring a consistent approach to safety (UN Economic and Social Council, 2001; US DOT Federal Highway Administration (FHWA) 2006; US Transportation Research Board, Committee on the Role of Public Transportation in Emergency Evacuation, 2008; UK Parliamentary Office of Science and Technology, 1997).There are significant differences between rail and road tunnels, both in their functionality and safety requirements. Most tunnels over a certain length are equipped with emergency ventilation systems capable to control the spread of smoke by creating an air stream in the desired direction. Besides ventilation, fire-life safety (FLS) includes smoke and heat detection by linear or spot detectors, closed-circuit television (CCTV) and public address systems with prerecorded announcements, as well as evacuation signage and monitoring capabilities (Vägverket – Swedish National Road Administration, 2004).There isn’t a consistent, worldwide approach to the design of emergency ventilation systems for tunnels, with significant differences from continent to continent (US DOT Federal Highway Administration (FHWA), 2004, US Federal Transit Administration, Transportation Research Board, 2006). In North America US NFPA 130 and 502 standards for rail and road tunnels, respectively, represent the main criteria, however, they are continually revised and new versions issued every three years. For road tunnels the World Road Association PIARC issues guidelines, but they are not truly enforceable. There are no similar international guidelines for rail tunnels, except general recommendations by the International Association of Public Transport (UITP) (IAPT, 2003).In Europe the Directive #54/EC adopted by European Community Parliament in 2004 requires a minimum level of safety for road tunnels users in all existing and proposed tunnels in the Trans-European road network that are greater than 500 m in length. Authorities having jurisdiction in many other individual countries, such as Australia, Austria, Germany, Japan and others, enforce specific safety regulations (Miclea et al, 2007). While it is impossible to summarise all aspects of this topic in a short paper, a review of the design approach, the existing differences in safety requirements, as well as applicable design solutions to meet safety codes for both rail and road tunnels are discussed below.

Mar 8, 2011

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By J Y. C Lo

The construction of two drainage tunnels and the associated subvertical drain system at the Po Shan area in Hong Kong was completed in December 2009. This project is the first of its kind to utilise drainage tunnels and a network of subvertical drains to regulate the groundwater table to enhance the long-term stability of the hillside of Po Shan area.The groundwater levels, monitored by preinstalled piezometers, once exhibited dramatic drops during drilling of the subvertical drains; however, have recovered from natural replenishment after effectively plugging of the drains. The level of groundwater drawdown is in line with the design function of the subvertical drains. In order to understand the groundwater flow pattern in the Po Shan area during and after construction and to set out operation schemes for the subvertical drain system so as to control the groundwater table in the Po Shan area, a post-construction review has been carried out to examine the behaviour of the drainage system and its impact on the surrounding subsurface groundwater flow.This paper presents a review of the groundwater monitoring data during and after the construction of the drainage tunnel system covering a period of over 3.5 years. A simplified conceptual hydrological model is developed, which has been verified by the monitoring data, to capture the key elements with regard to groundwater variations in different stages of the construction. The performance of the tunnel and subvertical drain system as revealed from these field measurements is discussed.

Mar 8, 2011

By N Wharmby

In recent years in New Zealand there have been a number of tunnelling and deep directionally drilled pipelines projects that have required access shafts. Often these shafts are in urban environmentswhere vibration and high noise levels are not tolerable. There are a number of methodologies that can be adopted dependent upon the shaft plan area, depth and geology.This paper will describe some different methodologies that can be adopted that use piling methods such as large diameter piles, and secant piles. The paper will use case studies to highlight:· construction methodology,· specific methodology issues and constraints,· lessons learnt, and· recommended specifications.The development of piling technologies in New Zealand has enabled the development of cost effective solutions for the construction of deep shafts in sensitive urban environments.

Mar 8, 2011