Search Documents

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

By K Williams, G M. Evans, S M. Iveson, K P. Galvin, C E. Loo

The Australian Research Council (ARC) has recently established an Industrial Transformation Research Hub in the area of iron ore, focused on iron ore characterisation, beneficiation, materials handling and end-use functionality. The research hubs are part of a new initiative aimed at building stronger relationships between industry and universities, while addressing issues of national significance. The ARC Research Hub for Advanced Technologies for Australian Iron Ore will focus its attention on developing innovative approaches for creating enhanced value across the full value chain through the characterisation of different ore types, beneficiation and materials handling and transport. This hub brings together five industrial organisations and a research team formed from well-established research groups based at the Newcastle Institute for Energy and Resources. These groups have a record of working closely with industry to create opportunities. Examples include new beneficiation technologies such as the Reflux Classifier for achieving gravity separation, the expertise of TUNRA Bulk Solids in materials handling and the Iron Making Centre at Newcastle, which is a capability maintained by BHP Billiton following the closure of its Technology Centre in 2009. The purpose of this paper is to provide an outline of the research hub and its objectives, some background on the research groups that now form the hub and an insight into the strategy adopted for developing and implementing new technologies. The paper also describes a range of novel technologies that have the potential to be developed and applied to iron ore beneficiation.CITATION:Galvin, K P, Roberts, A, Loo, C E, Evans, G M, Williams, K and Iveson, S M, 2015. Australian Research Council research hub for advanced technologies for Australian iron ore – an introduction, in Proceedings Iron Ore 2015, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By J Harris, J Li, M Shi, P A. Kirsch, D Sprott

Australia has an enviable global reputation as a leader in health and safety outcomes in the hazardous industry of mining, in part due to an increased application of risk management regarding operational planning and mining practice. In 2010, the Australian Coal Association Research Program (ACARP) initiated a major project, RISKGATE, to build, capture and deliver a national body of knowledge to assist companies with the management of risk in coal mining. The online system contains information for tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives underground, explosives open cut, manual tasks, slips/trips/falls, outbursts, coal bumps and bursts, human–machine interface, tailings dams, occupational hygiene and inrush. In 2014, RISKGATE is developing content for fitness for work (fatigue, drugs, alcohol, physical well-being, psychosocial well-being).This paper analyses underground mining fatalities in Australia and the United States since 2002 and introduces RISKGATE with a focus on the knowledge base for management of hazards in underground operations. Through capturing coal industry expert operational knowledge, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover within the mining industry. This coal-based body of knowledge is a platform that can be evaluated and implemented for other mining domains and high-risk industries within the energy supply chain.CITATION:Kirsch, P A, Shi, M, Harris, J, Li, J and Sprott, D, 2014. RISKGATE and underground operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 11–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By M D. Uttarwar, R R. Yerpude

India is the world’s third-largest producer of coal and is endowed with the fifth-largest coal reserves in the world. Surface mining straddles the entire domain of the Indian coal mining industry, yielding over 88 per cent of production. With continually rising domestic demands, it has to shoulder the responsibility of sustaining the requisite increase in coal production and chasing commensurate stripping targets. Such an ambitious task calls for the deployment of smart technologies. In such a demanding situation, cast blasting of overburden has emerged as a promising alternative for enhancing production and productivity of dragline pits.The cast blasting technique reduces stripping costs significantly as it utilises the chemical energy of explosives in place of mechanical energy to move large volumes of overburden quickly. Proper application of cast blasting not only reduces overall mining costs but also increases coal production. This paper investigates and evaluates the potential of the cast blasting technique, with special reference to dragline pits employing the rehandle method of extended bench. The economic feasibility of the technique is also ensured under different scenarios so that considerable benefits would accrue to the individual surface coalmines. To underline the efficacy of the technique, different cast blasting models have been formulated under a range of operational and economic scenarios that resemble present day practices in India. In order to test for economic variability in the application of the technique, a risk analysis of all the formulated cast blasting models is performed using net present value.CITATION:Uttarwar, M D and Yerpude, R R, 2015. Potential of the overburden cast blasting technique in Indian surface coalmines – a modular approach and its financial implications, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 655–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By K Saito, M Hasegawa

Removing sulfur and phosphorus from molten iron can be expressed by the following reactions, respectively. [S]Fe + (O2-)slag = (S2-)slag + [O]Fe [P]Fe + (3/2) (O2-)slag + (5/2) (FeO)slag = (PO43-)slag + (5/2) Fe(liquid) These equations indicate that desulfurisation and dephosphorisation have opposite oxygen potential conditions. If a small amount of desulfurisation slag not removed is carried over to dephosphorisation process, the reaction of sulfur mentioned above proceeds toward left hand resulting in increasing sulfur content in molten iron. For better understanding of such re-sulfurisation reaction in hot metal pre-treatments, the present study aimed at evaluating the effect of iron oxide on the sulfur distribution ratio between slag and hot metal. To measure sulfide capacities and FeO activities simultaneously at temperatures below the melting point of pure iron, CaO-SiO2-FeO and CaO-Al2O3-FeO ternary molten slags were brought into equilibria with copper-iron-sulfur liquid alloys, and the equilibrium oxygen partial pressures were determined with an electrochemical technique involving the stabilised zirconia solid electrolyte. The experimental results showed that the sulfide capacity increased with an increase in FeO content, and this trend was consistent with the fact that FeO was basic. Although the addition of FeO raised the FeO activity and oxygen potential, the calculated value for sulfur distribution ratio between slag and hot metal increased with increasing FeO content.

Jun 19, 2024

By S Bailey

In-field sampling programs generally take time, equating to money, and unless you have an onsite laboratory, you have the issue of having to wait long periods for your data. Until recently, field portable X-ray fl uorescence (FPXRF) analysers, which can help provide instant indicative results, were not able to detect penalty elements, such as Al and Si, or do so reliably enough to act upon.The purpose then of this field test then was to show that the latest FPXRF devices are capable of producing reliable readings on field samples of variable grain size, in particular for Al and Si, such that the readings still correlate well with the assay for those samples and thus be reliable for an iron ore grade control application.We tested RC chip samples on-site in the Pilbara, Western Australia, with the Niton, analysing for a range of elements including Fe, Mn, Al and Si and then compared the results for those elements against assay data for the same. A strong correlation would tell us that the FPXRF results were reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for the all of the four elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 0.998).The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF.The data showed allowed for two conclusions:1. the FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with assay, is reliable for a fi eld application in drilling and grade control; and2. the greatest limitation to data quality is sample preparation.

Jul 11, 2011

By A E. A Northcote

The drive to maximise performance, reduce maintenance times, improve safety of operation and maintenance on mining equipment while keeping both operational and capital costs down has provided good nourishment to the creative thinking of designers of skip loading facilities for hoisting systems. Early systems were as simple as manual loading which evolved into a surge bin feeding a skip through a chute finally maturing into a measuring flask discharging into a chute to feed the skip and more recently high capacity skip feed conveyors. This paper will compare the concepts of the skip loading flask and the skip loading conveyor systems over a range of winding distances and hoisted tonnages. The comparison will draw on actual installations and review operational, maintenance and safety. An order of magnitude capital cost estimate will be used to complete the financial comparison. This will enable the reader to understand the concepts and costs and assist in selecting the appropriate skip loading system.

Mar 21, 2011

By D H MACKENZIE

In common with several great orebodies and mineral camps around the world Broken Hill has been the subject of state-of-the-art technical and scientific scrutiny during its long working life. During the early years geological interest in Broken Hill tended to be directed at the body for its intrinsic scientific worth, mainly on account of its large size, high grade and wealth of mineral species. For much of the last 60 years the interest has had a more applied motivation, namely, to assist the search for either repetitions in the Broken Hill field or analogues in other terrains. This paper looks at the major changes in geological concepts and exploration techniques applied at Broken Hill and attempts to assess their impact.

Jan 1, 1992

By R M. S Watsford, M Davis

In 2015, MMG Limited commenced further action to improve operating margins and establish a blueprint for future growth in the Australian environment. This action was taken in the context of weakening metal prices and high input costs that arose during the Australian minerals boom.MMG was formed in June 2009 following the purchase of the majority of assets of OZ Minerals Limited by China Minmetals Corporation (CMC) through its subsidiary China Minmetals Non-ferrous Metals Co Ltd (CMN).Since formation MMG has been implementing a business model to deliver a standard way of operating. The overarching purpose of the business model is to enable fast integration of acquired assets to realise improved productivity and performance. CMN established MMG as a vehicle to reach their growth targets through further development or acquisition of mineral assets in jurisdictions external to mainland China.The business model is underpinned by the MMG operating model. The operating model defines how MMG is arranged to deliver the company strategy.This paper describes the application of the operating model to the formation of the Australian operations into a single business unit from multiple stand-alone operating sites. The development and impact of the business model on MMG’s performance is also presented.The extension of the operating model to the Australian operations has led to improvement in safety performance, direct costs and productivity. These improvements have been achieved through reducing duplication, simplification of systems and rapid deployment of improvement initiatives.The successful implementation of the operating model to Australian operations strengthens the platform for further growth. Hence, delivering on the aim of the business model.CITATION:Watsford, R M S and Davis, M, 2016. MMG’s Australian operating model – the implementation, successes and learning, in Proceedings International Mine Management Conference, pp 291-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By H Law, M Muller

Mount Isa Mines (MIM) Copper Concentrator currently utilises Agitair 120 banks for its roughing flotation circuit. Apart from a rotor change, the only other significant work completed to the Agitair banks since their installation and commissioning over 40 years ago has been a like for like refurbishment in 2016. The Agitair banks at the MIM Copper Concentrator currently utilise the Pipsa rotor design which progressively replaced the original Chile X rotor design in the 1980’s and 90’s in the copper concentrator. Since the development of the Pipsa rotors, modern rotors such as the Dorr-Oliver (DO) high shear rotors have been released to the market with proven recovery and concentrate grade improvements over previous rotor designs. This paper aims to detail the installation, testing and comparison of Pipsa versus Dorr-Oliver rotors in two different flotation sections of the MIM Copper Concentrator.CITATION:Muller, M and Law, H, 2018. High shear rotor trials in the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 393–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

As a result of cheap Maui gas and plentiful hydro-electricity, over the past few decades New Zealand has enjoyed some of the cheapest energy of any OECD country. The situation is changing; at best we are facing some radical changes in energy use, at worst we are facing a crisis resulting from the following:   Cause 1: Maui gas will be exhausted by 2012. Distorted pricing and supply contracts; resulted in Huntly Power Station, a coal mine mouth generator running on 70 per cent Maui gas until very recently!   Cause 2: Investment in new generating capacity (and transmission) is woefully inadequate; as a result hydro lake levels are being continually pushed to the limits.   Cause 3: Distorted thinking is everywhere, for example; æWe will find more cheap gasÆ. æGas is clean û coal is dirtyÆ. Hot air  û ægreen alternatives such as wind generation will save usÆ. æNo NuclearÆ. The outcomes of the distorted thinking will be price increases, then shortages (there is nothing like "black-outs" to focus national thinking) and finally recession.   But what can NZ do? - Mine Coal. Coal jump-started the industrial revolution, it can provide the transition to post-gas and oil. NZ has the second highest reserves of coal per capita in the world, yet we use less that any other country with significant coal reserves. Our exports of our best coal have increased threefold, yet out own consumption has remained static at about 1-1.5 Mtpa for the last 30 years. Our coal is NZ owned and inexpensive relative to other energy sources, even allowing for infrastructure and environmental costs.   What can we do? We as mining professionals can promote informed responsible development and investment in the country's mining and energy business. We can galvanise public opinion on issues such as æunbundlingÆ our entire energy chain from mine-to generator-through transmission, even if the nuclear issue has to wait! With oil above US$70/bbl substitution is feasible. For individuals, there is always solar!

Jan 1, 2006

By A Suwandhi, H Utama

PT. Indo Muro Kencana (PT.IMK) is a gold mine that is located in Central Kalimantan, Indonesia. Drilling and blasting activity is applied in order to support mining production. Drilling and Blasting (D&B) planning is conducted by its engineers. A drilling and blasting contractor conducts drilling and blasting activity. The objective of this paper is to evaluate the implementation of the scaled depth of burial (Chiappetta and Treleven, 1997) in explosive charging sheet application to increase blast efficiency. The function of the scaled depth of burial is to maintain stemming height above explosive charge in order to prevent the ‘over energy’ condition, to reduce the excessive fly rock possibility, to maintain rock fragmentation (digger’s productivity) and to increase blast efficiency. The focus of this paper is to implement the scaled depth of burial as a reference in D&B planning and practice, especially in designing stemming height. The purpose of this paper is to validate that the scaled depth of burial can be used as an engineering tool in D&B practice in PT.IMK. However, scaled depth of burial cannot applied as an engineering tool to determine stemming height above explosive charge for trim blastholes and secondary blasting area. In general, the implementation of the scaled depth of burial in PT.IMK is applicable for production blastholes (ore and waste blasting). In conclusion, it is clear that scaled depth of burial can be used as an engineering tool to create explosive charging sheet and also to increase blast efficiency (ore and waste blasting) in PT.IMK.

Jun 22, 2022

Based on relative CO2, N2, and 3He contents, geothermal systems of the Taupo Volcanic Zone, TVZ, can be subdivided into two major groups: arc-type systems, associated with andesitic magmatism along the eastern boundary of the TVZ, and rift-type systems over its western parts. The highly increased N2/3He, CO2/3He and CO2/Cl ratios of the former are ascribed to entrainment of large proportions of volatiles of subducted, marine sedimentary origin. The largely rhyolitic, rift-type magmas are assumed to have formed from volatile-depleted, residual melts. Correlations of Cl and CO2 with heat contents suggest that formation of the two types of source magmas involves mixing of two end member components: a low-volatile melt with a heat/Cl ratio of 25 Ml/mol (0.7 MJ/g), and a low Cl vapor with a heat/CO2 ratio of 5 Ml/mol. On the basis of these values, the heat associated with andesitic magmas is found to be carried in close to equal parts by both vapor and melt; for the rhyolitic melts the proportion contributed from the vapor is only about 2%. The heat/He ratios of the rhyolitic source magmas for the rift-type geothermal discharges from the TVZ of 0.12¦0.05 Ml/pmol is within the range of 0.05 to 0.2 Ml/pmol of the upper mantle. The higher heat/3He ratios for the arc-related magmas of 0.4¦0.2 Ml/pmol are likely to be due to the high proportions of heat carried in the form of a separate, low 3He vapor phase derived largely from subducted sediments.

Jan 1, 1995

The complicated mining-geological conditions in the Kuzbass have led to some difficult mining situations in the past. Now, with historical data, supplemented by geomechanical information and measurements, together with an appropriate kinematic theory, a more reliable basis exists for prediction and control of the geomechanical state during extraction, with caving and with backfilling. Continued progress and improving reliability comes from data banks and computations, and now prediction of geomechanical situations is upgraded by more routing measurements and monitoring. Not only in the Kuzbass, but throughout the USSR, 14 dedicated groups are ready to solve various specific problems of prediction an control of geomechanic situations with assured increase in the quality of mining.

Jan 1, 1991