Search Documents

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

The sulphide ores of the Kalgoorlie goldfield have long been looked upon as' refractory, involving special metallurgical treatment. For many years two kinds of treatment have been practised-(l) wet treatment, including fine grinding, amalgamation or concentration of the free gold, concentration of the sulphide minerals with subsequent roasting and cyanidation, and cyanidation or bromo-cyanidation of the residue from the concentrating operation; (2) dry-crushing of the ore and roasting the whole of thecrushed ore, amalgamation of the gold in the calcine during fine grading, followed by cyanidation. The wet treatment was advanced a stage further when, in 1929, the Lake View and Star Ltd. adopted large scale flotation. As a consequence, however, further metallurgical problems were introduced. This paper covers the investigation, ,of one of the most prominent of these problems.Flotation preceded by strakes was satisfactory to a point.The flotation concentrate consisted largely of auriferous pyrite and tellurides, and the gangue minerals in the concentrate were practically barren.Several sources of loss of gold values were, however, found to be associated with this circuit, viz.-(a) There was the loss of gold in the flotation tailing.(b) Loss by dusting during roasting of the flotation concentrate.(c) Loss of gold in the cyanided residue.

Jan 1, 1937

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021

By Boyd GL

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal rCCOvCrCd h\ hi'eh ss-all mining methods.

Jan 1, 1998

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By MacLean L

In 1975 the Commonwealth Government established import parity pricing for all liquid hydrocarbons discovered after the 16th September, 1975. These discoveries were termed "new oil" to differentiate them from existing discoveries and production. Overnight the price of the product being sought trebled, resulting in greatly enhanced economics by increasing the potential returns on existing prospects and by making smaller plays economically viable. After 18 years of drilling, the offshore Gippsland Basin has attained a moderate level of exploration for a basin of its size. Fifty seven prospects have been drilled within the basin but only a few of these were drilled along the southern and northern margins, while the deep water areas along the eastern margin have remained virtually undrilled following the Hapuku-1 oil discovery. The major hydrocarbon accumulations within the basin are trapped beneath the Latrobe Unconformity surface and exploration has largely concentrated on this single play in areas immediately adjacent to the major producing fields.

Jan 1, 1982

By Hryniewicz M

The paper presents a sound critical estimate of mathematical models presently used for the process of compaction of fine-grained materials. It shows the mathematical model of compaction developed by the authors, which was used to formulate the program of computer simulation of the process. The examples of computer simulation experiments of compaction of selected fine-grained materials regard the results of the experiments made by the authors on variability of external friction occuring in this process. Simulation examination presented in the paper crucially contributed towards the original method of selection of rational compaction technologies of fine-grained materials developed by the authors.

Jan 1, 1993

By Walker G. S

Infrared and Raman spectroscopy have been used to study a range of solid state and aqueous solution species which are of interest in extractive metallurgy. In the solid state new Cu(II)/CN'/NH3 complexes have been detected, iron impurities in kaolin characterised, aluminium substitution in hematite and goethite quantified, and the crystallinity and orientation of zircon determined in heterogeneous crystals. In aqueous solution metal cyanide complexes and equilibria were readily characterised, the thermal decomposition of SO2 monitored and products identified, and complexation of AI(III) by hydroxycarboxylates observed. Attempts to monitor the early stages of the gelling of silicate solutions were less successful, with only changes in the gel being detected. However, the degradation of 12-tungstosilicic acid was readily monitored as a function of both time and pH.

Jan 1, 1996

By Arndt MB, Bamberg S

The evaluation of risk is becoming more important in the siting of mining operations in the United States as well as the rest of the world. The determination of environmental, economic, as well as health and safety risks is an important step in the planning of any mining operation. Hydrogeology plays an important role in pre-mine planning and in the determination of these risks. The mine operators must determine if ground water would inhibit mining in any way. Factors which are important to consider include mine dewatering economics, slope stability, and other adverse hydrologic impacts. This paper presents methodologies for the characterization of hydrogeological risks for a mining operation. First of all, the term risk analysis is defined and its utility is addressed. Then, stepwise methods for performing a typical risk analysis are presented. Finally, the application of risk analysis to hydrogeology in mining is given. With slight modification, it is believed that these methodologies can be used to evaluate the hydrogeological risks for any mining operation.

Jan 1, 1988

By D S. Clarke, K B. Sporli

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins. The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

By M Scoble, R A. Hall

The mining industry has aggressively sought competitiveness through increased productivity and return on investment. A primary strategy has been the pursuit of economies of scale. This has also been dependent upon the implementation of new technology and systems integration. System integration has been accomplished through the implementation of mine dispatch, global positioning and mine wide communication technologies. These technologies have tended to advance at different rates of development and implementation. The result has been that across the industry, and even within companies, mines are at various stages of operational system re-engineering in these areas, driven by improvements in productivity and operational efficiency. Although this strategy has been successful, little effort has been made to analyse change in operational performance in order to understand and model the effects of scale in a quantitative manner. This paper considers the particular impact of equipment scale, together with potential future trends. It then presents and demonstrates a preliminary method to quantify through simulation the anticipated benefits of economies of scale.

Jan 1, 2003

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

By M J. Nugus

The Geita gold mines in north-western Tanzania have produced 5 Moz of gold from an estimated endowment of 15 Moz. They are generally classified as typical Archaean orogenic banded iron formations (BIF)-hosted gold deposits in banded iron formations as described by Goldfarb, Groves and Gardoll (2001); Neall and Phillips (1987); Phillips and Powell (1993) and Neall (1987). The controls on gold mineralisation have been reassessed to conclude that Nyankanga, and we conclude that Nyankanga, the largest deposits within the group, developed during a dynamic and protracted deformation history intimately associated with several stages of hydrothermal fluid flow and alteration. The fluid-induced fractures associated with gold mineralisation are primarily manifested as submillimetre to metre-scale fractures and breccias developed preferentially in rocks that have been previously deformed and altered by silicification or seafloor metasomatism. This realisation detracts from the exploration and mining strategies that would solely concentrate on fluid pathways and associated wallrock alteration and veining solely within the BIFs as hosts for economic gold mineralisation.

Aug 22, 2011

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

By Nettle W. H V

THE past few years have seen a considerable expansion of the roasting of blende in Australia. The bulk of this blende is Zinciferous concentrate from Broken Hill and now forms a very considerable source of sulphur for the acid manufacture. It will bereadily conceded that Australian sentiment is in favour of utilising all known potential wealth, especially that won from below ground, as this once disposed of is gone forever. If Australia does not make sulphuric acid from her sulphide ores we may be sure that the purchaser of these ores will do so if in any way possible. It must not be assumed, then, that the difficulties met are mentioned with the idea of undue criticism, but rather to show that, although most of the intial troubles have been overcome, there are still a few to be encountered; and with the hope that comment brought forth will aid in the solution of the problems facing an industry at present little more than in its childhood as far as Australia is concerned.Blende roasting is done in mechanical furnaces of various makes, and mostly without the aid of other fuel than the sulphur in the ore. It will be our aim to touch on the various difficulties in the order in which they occur in the train from furnace to acid plant.

Jan 1, 1926

By N Boughen, P Ashworth, S Johns, C J. Yeats, A Littleboy

The ocean floor, often called the last frontier, is increasingly discussed in terms of its resource potential û from near shore building aggregate and placer deposits to massive sulfide orebodies in the deeper ocean. Consequently there is an increasing incentive to mine the seafloor. But, do we have the social license to explore and mine the seafloor? Does this nascent industry have support amongst the wider community? If not, why not? And what should be done? To answer some of these questions, the Wealth from Oceans National Research Flagship has explored the social viability of an expanded seafloor exploration and mining (SEM) industry inAustralia. The results show that there are significant geological and environmental data gaps and that, in the absence of sufficient information, stakeholder reaction to the prospect of an SEM industry expansion may be reactionary and negative. This uncertainty means that the perception of risk from the industry is variable and often dependent on individual values. The acceptability of an expansion to the SEM industry is currently precarious, in particular due to the high levels of uncertainty regarding the environmental impacts of seafloor activity. While there are existing federal regulatory frameworks and government processes for the licensing of seafloor mineral exploration and extraction, there is little precedent in the application and implementation of these regulations. The future viability of the industry will be highly dependant on AustraliaÆs ability to improve the knowledge-base underpinning its regulatory regime and also to generate open and transparent communication channels between stakeholders. It will also be dependent on the SEM industryÆs ability to communicate an acceptable value proposition to society. This proposition will need to include the relative impacts of terrestrial and marine mining, the alternative potential uses of the ocean and the multi-use conflict that SEM might engender. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This paper describes the planning mechanism and implementation of a progressive rehabilitation programme at Hunter Valley Mine in the Upper Hunter Valley of New South Wales. Hunter Valley Mine is a large open cut coal mine which produces approximately 7.0 million tonnes of coal (run of mine) annually for export. This production level involves the movement of some 60 million tonnes of waste and coal each year.The rehabilitation programme at Hunter Valley Mine has been developed to provide a combination of pasture, based on improved pasture species and timber belts to enhance the visual characteristics of the rehabilitated landform, whilst creating amenity in the form of shade for livestock.The operational philosophy for the rehabilitation programme is that of progressive rehabilitation. The best time to undertake rehabilitation is now.' As a result, planning for the rehabilitation programme is continuous, so that all site works are completed in time for vegetation establishment during the critical periods each year.

Jan 1, 1992

The control objectives and constraints for grinding circuits are ana- lysed, taking a single-stage ballmill-cyclone circuit as an example. The design of a hierarchical modular control system is described, for implemen- tation on modern microprocessor-based control systems. Product sizing measurement is identified as a problem area, and a new approach to product sizing inference, from on-line cyclone feed and overflow measure- ments, is presented. The procedure over-comes several practical difficulties of a previously proposed inferential method and is therefore expected to find application in more advanced grinding circuit control systems.

Jan 1, 1988