Search Documents

By A Mulyadi, J Barber, R Golden

The Deep Ore Zone (DOZ) underground mine will be a 25 000 tpd mechanised block cave operation starting production in 2000. The ore handling system consists of a direct truck dumping 54 +74 gyratory crusher, which feeds into an ore bin. An apron feeder below the bin is used to load a conveyor belt. This paper describes the design, sequencing and methodology of the crusher station, ore bin and feeder chamber excavations. The Geotechnical investigation and analysis of the site are also discussed as well as the design, installation and quality control of the long-term ground support methods.

Jan 1, 2000

By Ghiani M, Satta F, Zucca A, Peretti R

After a brief introduction on the principles of contact electrification and a synthetic illustration of the Turbocharger separator, the successful results obtained with different raw materials are given and discussed, with particular reference to a North African run-of-mine with carbonate gangue, a crude ore from India containing pyrite and a mineral sample from Angola having quartzeous gangue. The pre-eminent effect of target surface temperature in the charging device of the separator is emphasised. On the basis of the results of both batch experiments and long-run tests the prospects of industrial application appear very interesting both from the technical and economic points of view, even when compared with froth flotation.

Jan 1, 1993

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

There are a number of methodologies which can be used for the preparation of environ- mental impact statements. Selection of a method depends upon the type of project and the environmental characteristics of the area where it is to be built. Most methods are satisfactory for assessing impacts on the physical environment but less so for the biological. Major problems may arise in deal ing with sociological issues because value judgements are involved. Several methods of approaching problems of this nature have been tried with some limited success.

Jan 1, 1976

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

By G A. Streltsova

In the paper the main concept of qualitative simulation is determined when computer-aided designing and forecasting of designs of robotised continuous-flow working face complexes for underground mining of hard ores. The parametric model æunderground ore mineÆ and its components û composite models are considered. Frame description of structure of working face complex and methods of organising of rule-oriented representation of knowledge when itÆs operating are given. The architecture of the developed prototype of expert system æworking face complexÆ and construction of a knowledge base for it are described when solving problems of multi-criteria optimisation of computational parameters of the working face complex under conditions of uncertainty. The guidelines for further development of knowledge base and expert system are given.

Jan 1, 2003

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988

Mine production planning and scheduling as a production planning problem can be handled using Linear (Goal) Programming. This approach is particularly useful when the product quality is important. This has been shown for many mine planning cas

Jan 1, 1998

A case-study is presented of the tailings dam of Nairne Pyrites Pty. Ltd., at Brukunga, South Australia. The methods of-construction and operation of the dam are outlined over the whole working life of the mine. Procedures of soil mechanics used to estimate the stability 'of the face of the dam are described, and seepage problems are dis- cussed. It is concluded that the dam is basically stable, and enabled Nairne Pyrites Pty. Ltd. to dispose of tailings economically, although more attention to seepage control may have been ad- vantageous. Suggestions are made on the construction and operation of tailings dams elsewhere.

Jan 1, 1975

By Floyd JM, Richardson P

The extension of theoretical and laboratory studies of the roasting of tantalite and cassiterite concentrates from Greenbushes Tin Limited to pilot and semi- commercial plant developments is detailed. A rotary pilot furnace was used to prove the feasibility of the process and a semi- commercial plant was constructed at Greenbushes to produce large quantities of roasted calcine. The additions and conditions of the laboratory study were employed to achieve marketable grades of calcine from the two materials. As well as producing calcines with less than 0.1% Sb, most of the tin in tantalite was recoverable to a separate fume product. Tin fumed during cassiterite roasting on a semi-commerical scale amounted to less than 1% of the tin in feed.

Jan 1, 1986

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

New Zealand China Clays operata a plant at Matauri Bay, Northland for the benefaction of hallosite clay. Production is several thousand tonnes per year of which about ten per cent per year is supplied to an expanding export market.

Jan 1, 1978

By Rogers J. F, Bird A. C

The establishment of vegetation for dust control on tailings dams at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) is outlined. The evolution of practices and techniques employed is described and the problems encountered are discussed.

Jan 1, 1983

By Mansor A. N

Results are reported for the computer simulation of heap leaching of mixed copper oxide and sulphide ores. They resemble those obtained from testwork in terms of a substantial peak in the copper concentration of the pregnant solution, an initial period when no copper emerges and a lengthy period towards the end when the copper concentration and the daily increment in copper recovery are low. The simulation can be used to forecast process results before any column or similar testwork is performed. Potential applications of the simulation to process design, operating strategy and optimisation are discussed. Three modes of operation are identified that correspond to different performance patterns and dependencies on ore and process variables. The relative merits of different operating strategies for approaching the ideal performance are being investigated. For process design and development purposes, the simulation may be used with a limited testwork programme to achieve significant savings in time and resources.

Jan 1, 1989

The number of employees required to operate a continuous operation was determined. The fixed and variable costs of the operation were separated, generally along the lines of labour and stores components. Proprietary `MicroPlanner' scheduling software was used to assess resource utilisation under the constraints generated by seven-day operation to determine the level of resources required and ensure that the maximum use was being made of all resources. The mine economic model was used to account for both the fixed and variable costs of the various task to determine the cost and net revenue of the various scenarios. The analysis indicated that mine output could be increased while reducing the unit production cost. Several eight- and 12-hour, seven-day rosters were sourced and ranked for their potential to improve production and communication, and for their effect on employee health and lifestyle.

Jan 1, 1995

The advent and easy availability of fast and powerful digital computers has marked a transition from one era to another in the field of process control in many industries. Mineral processing is no exception. Aims, practices and problems associated with process control of mineral beneficiation plants in the 'old days' are compared with those available at present. Although basic processes remain generally the same, there have been simultaneous social and economic developments, which directly relate to the development and present value of process control. Lower head grades are now treated, plant capacities have increased, and a large proportion of future capital in the mineral industry will be associated with large capacity plant, treating still lower grades. Environmental considerations have pressurised moves to better control in some areas. With these changes, economic operating incentives have changed, and process control has, in many plants, become more critical. Finally, while computer technology has developed recently at a very rapid rate, developments in the fields of instrumentation, basic on-line measurement and sampling have in general lagged behind, limiting the progress possible in process control. Hence, the benefits of computer control vary depending on

Jan 1, 1977

This paper examines the various stages of development and design work which were necessary to develop the cemented rock fill system for copper mining at Mount Isa. The reason for a cemented sand fill development program together with details of the test work undertaken are briefly outlined. The testwork associated with the selection of a suitable local rock to supple- ment the cemented hydraulic fill is discussed, as is the method for underground placement and mixing of the graded rock with the cemented hydraulic fill. The design features of the final system which incorporates a graded rock handling system and a cemented hydraulic fill reticula- tion system is outlined.

Jan 1, 1973

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

Modern mining and coal cleaning techniques lead to the generation of large quantities of fines which give rise to problems in their storage, handling, transportation and further processing. Pelletisation, a method of particle agglomeration, can alleviate such problems. This paper provides a brief overview of the principles of pelletisation and a survey of the coal pelletisation literature. Then it reports results from an experimental investigation of the effect of surface active reagents on coal pelletisation. Finally the paper is concluded with a few remarks on applying the results from the experimental study to practical coal agglomeration.

Jan 1, 2000

By Gillies A. D S

A device has been developed for modelling the behaviour of coal under conditions which may lead to spontaneous combustion. It is designed to model the behaviour of a stockpile of large mass. The apparatus can test coal samples taken from the flow stream from mine through washing, stockpiling and transportation to the point of utilisation. It tests samples in an as received' condition and so takes into account the effect of aspects such as particle size and moisture content on propensity for spontaneous combustion to occur. Results of the preliminary tests undertaken are given and future applications of the apparatus are Discussed.

Jan 1, 1995