Search Documents

By I T. Ross

In the last 50 years there have been tremendous improvements in equipment used in development on underground mines. Compressed air powered jacklegs have been replaced by high powered electro-hydraulic drifters on sophisticated drill jumbos and load haul dump units have taken over from small shovels and rail cars.Despite the increase in power applied in key parts of the development cycle, average advance rates have fallen and costs have increased. The factor that is most often regarded as the main contributor to slowing advance rates is increased support requirements. Whilst there is no denying that the drive to improve safety has resulted in the requirement for more bolting and the installation of a skin support (mesh or shotcrete), this is not the only factor.Within the industry as a whole, many of the basic principles of development appear to have been lost over time. This paper looks at a historical case study and discusses some of the features of old development cycles that are no longer in use. This highlights some of the basics that appear to have been forgotten. These may be indicators to what may provide improvements in the conventional drill and blast development cycle.CITATION:Ross, I T, 2014. Development – back to basics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 67–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Stow, M Edmondson

Lemington coal mine is operating in an environmentally sensitive area in the Hunter Valley, NSW, Australia. Late in 1999 the southern pit was developed using a series of box cut blasts. After the initial development the area would have been free dug due to the soft, well-jointed nature of the deposit. However, it was decided to trial drill and blast to determine if shovel productivity could be improved to enable an overall mining cost reduction. The initial trial blast results were less than satisfactory with both environmental issues occurring and the desired shovel productivity not being achieved. An audit of the blasts indicated that wet ground and the presence of soft clay inter-bedded with harder rock caused the poor blast results. Also, water-affected explosive product combined with explosive energy loss into soft ground led to flat spots and tight digging in the hard band areas, resulting in the lower dig rates. Lemington Mine and Orica Explosives developed a plan to match the rock with the appropriate explosive type and energy. This resulted in a number of blasts over a six-month period using a new non fuming explosive product, æNovaliteÆ. The results have been excellent with the environmental issues being totally resolved and dig rates improved, enabling reductions in mining costs. This has allowed the mine to continue with their exemplary record of environmental management whilst achieving operational efficiencies.

Jan 1, 2001

By S S Solomons

In 1991 the uranium spot market price dropped to approximately US$7/Ib U308, a historical low in real terms and the short-term outlook for the industry in the next five years was grim. At this time the Ranger operation was producing uranium concentrate at its design capacity of approximately 3 000 tonnes/year. The loss of two major long-term contracts owing to price and reduced power utility demand due to excess inventories meant that the company could not match production to sales. Continuance at this production level would have resulted in a rapid buildup of product inventory and the tie-up of significant cash reserves. After analysing various options, an innovative operating strategy was devised such that production and sales were approximately balanced without a significant impact on the unit production cost or a long term effect on the plant or operation. A campaign mining/milling operation commenced and approximately 40 per cent of the workforce were retrenched. Multi-skilling of all employees was a critical aspect of ensuring a successful outcome. This paper examines the strategy and reports on the success of the operation two years after the restructuring exercise was effected in November 1991.

Jan 1, 1994

By S Hall

Mining schools around the world, many unfortunately now closed, were often established to teach the techniques of narrow vein mining and associated processing to students studying part-time while working in the industry. This arrangement ensured graduates (or æassociatesÆ) had a mix of skills and knowledge invaluable to the industry.It is argued that there is still a need to educate students in these narrow vein techniques and that there will be a growing demand for such graduates with a high level appreciation of this type of mining. There is also a need for innovation in narrow vein mining and processing to develop specific technologies and allow the use of techniques applied in æbulk miningÆ to achieve improvements in productivity, safety and economic performance.This paper aims to review the situation with regard to education and innovation in narrow vein mining.CITATION:Hall, S, 2012. Narrow vein education - back to the future?, in Proceedings Narrow Vein Mining 2012 , pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By C Torrisi, J Andreatidis, M Duffy

BHPÆs Cannington process plant was commissioned in October 1997. The Cannington ore contains high grades of silver, lead and zinc but also contains high levels of fluorine which must be removed to produce a marketable concentrate. As a consequence the plant is more complex than the typical base metal concentrator. Some of the features of the Cannington operation include a single stage autogenous mill, multiple stages of flotation cleaning, two leach circuits, pressure filtration and a paste fill plant. The start-up and achievement of design performance for new lead/zinc operations has traditionally taken much longer than for gold or copper operation and is littered with many tales of woe with feasibility targets often not achieved (Agarwal, Brown and Katrak, 1984; Bulatovic and Wyslouzil, 1999; Leung, Andreatidis, Woodall and Alford, 1996; Sherman, 1999; Ward, 1998).

Jan 1, 2000

By Van Nostrand J

The resettlement and relocation program that is being carried out at Gold Fields Ghana's (GFG's) Tarkwa Mine is currently the largest of its kind in Ghana, and West Africa as a whole. While such projects have been initiated previously in Ghana, in connection with the development of the Volta River Dam, Tema, and a number of other smaller resource development projects, they were not subject to the statutory requirements of Ghana's relatively new Environmental Protection Agency (EPA). Nor were they subjected to the kind of global scrutiny that is now being applied to such projects by international agencies like the World Bank. This is a result of the international community's criticism of major energy projects like the Three Gonges Dam in China and a number of similar hydro-electric projects in Southern Asia. It has meant that for this project the expectations are considerably more challenging then they have been in the past.

Jan 1, 1997

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

Over the last 15 years working in the mining, construction and extractive industries, one of the areas that has always concerned and at the same time drawn the author to it is the application of drilling and blasting in the underground development mining and civil construction tunnelling fields. In that time, the author has come across many drives and tunnels that are larger than design or badly damaged in the perimeter or both. When the question is asked as to why this is the case, the reply is generally æthatÆs the way it is and always has beenÆ. Sometimes it is blamed on bad ground, bad drilling, bad explosives, bad initiation or just plain bad. Most operators build a dilution factor into development and tunneling costs as an acceptance of overbreak and similarly pattern bolt everything to overcome excessive perimeter damage. This paper will attempt to unravel some of the mysteries behind perimeter drilling and blasting in underground drives and tunnels and discuss methods to reduce overbreak and therefore reduce costly dilution and to minimise perimeter damage which in turn will allow more cost-effective ground support. It should not be assumed that better drilling and blasting alone would automatically allow an operation to reduce ground support. The operator must still æreadÆ the ground and its characteristics in order to ensure sufficient ground support is placed to allow the operation to progress safely. This paper will not go into the intricacies of bolting, meshing, shotcreting, concreting and other ground support, but it will use indicative costs for the primary areas of drilling, explosives, excavation and labor to show the magnitude of cost-efficiencies which can be obtained through improved drilling and blasting applications. Drill and blast remains the most flexible and cost-effective method of underground excavation as long as it is applied safely and effectively.

Jan 1, 1999

The role of the mine geologist in a business perspective is self-evident to some, but to others it may be a new concept. All mine geologists need to know exactly how they add value to the business if they are to be successful. Alternatively, if they do not add value, then they will become redundant. This paper seeks to understand some of the contributing problems that hinder the mine geologist from operating in a business perspective. In doing so, a new context (for some) is proposed to aid the mine geologist and the operation gain greater value from geology. The proposal suggests how to ensure that the activities of our geologists are intrinsically linked to the business process that we are involved in. The mine geologist can and must play a pivotal role in the success of an operation. To do this, they must understand some principles of business such as:process, customer/supplier relationships, and organisational structure. Our geologists must know the business objectives, understand the product that the customer needs and use their geological skills to deliver the product safely, on time and to specification. As geologists, we can be instrumental in ensuring that the operational environment is structured in such a way that maximum value is realised, not only from the mine geologists but the entire site team. In doing so, mine geologists will realise their full potential in delivering the outcomes the business demand, and therefore be recognised as strong contributors to business success.

Jan 1, 2000

By A Litwinowicz, M Laxman, A Fourie, A L. Li

This paper presents a design approach and analytical methods that were used for assessing the potential of static liquefaction and developing the mitigation measures for a tailings dams. The rigour of the design and analysis approach represented leading practise in the industry to address static liquefaction, which contributed to a robust design with high confidence and certainty. The salient features of our approach to static liquefaction included geotechnical investigation and tailings characterisation, static liquefaction screening assessment, static liquefaction triggering analysis, limit equilibrium analyses and numerical modelling of static liquefaction using the NorSand model, which was amongst the first tailings dam projects involving numerical modelling of static liquefaction using these methods.

Jul 1, 2021

By F M. Weir, M Fowler

A discrete fracture network (DFN) approach involves numerical modelling that explicitly represents how defects may be spatially distributed through a rock mass. A DFN is a 3D realisation of the ‘smaller scale’, non-deterministic defects; it is not an attempt to model larger, deterministic structures that should be identified as part of an engineering geology model. The approach utilises structural data in stochastic analyses to give a range of possible models that provides a tool for visualisation and analysis of a rock mass and indicates the potential large-scale slope or tunnel performance and stability.Stochastic fracture modelling for rock mass characterisation has significantly advanced over the past 25 years. With recent improvements to field data collection and computational power, it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses.This paper provides an introduction to the DFN approach, particularly the necessary input parameters and derivation of these from typical structural data sources, such as boreholes or scan line mapping. Of particular importance for engineering applications is validation of the simulated fracture network and techniques for doing so are discussed here.CITATION:Weir, F M and Fowler, M, 2014. An introduction to discrete fracture network modelling and its geotechnical applications, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 435–444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P Pieterse

Kumba Iron Ore Ltd is currently commissioning the Sishen Expansion Project (SEP) û a brownfields project on the Sishen Iron Ore Mine located in the Northern Cape Province, South Africa. SEP is designed to produce 13 Mtpa of product from 21.7 Mtpa of ROM feed. The beneficiation section of SEP employs jigs to process narrow size fractions in the 25 x 0.8 mm size range. The -0.8 mm fraction is screened out ahead of the jig plant and rejected as waste without any prior beneficiation. The processing of this fraction was not included in the early stages of SEP development because no suitable beneficiation or dewatering technologies could be identified within the time-frame required to implement SEP. This paper presents the SEP 1B project, ie the metallurgical and process engineering study that was done to evaluate the techno-economic viability of processing the -0.8 mm material of SEP. To support this evaluation, metallurgical bench scale testwork was done on selected samples characterising the material types used in the SEP for gravity concentration beneficiation. Subsequently, pilot testwork on a 300-ton bulk sample demonstrated that an integrated teeter-bed/spiral circuit could be used to successfully beneficiate the -0.8 mm fraction. The study has established the viability of the proposed process and has concluded that approximately 390 000 tpa could be produced and added to the SEP fine ore product without violating the applicable product specifications. The proposed process has been designed to be implemented in modular units in order to facilitate implementation and ensure future expandability. Based on the recommendations of the study, approval has been granted for the detail design feasibility study. Production is scheduled to commence in the first quarter of 2010.

Jan 1, 2008

The Morning Star diorite dyke has been subjected to two periods of mineralization. The earlier, genetically related to the dyke magma, gave rise to a weak chalcopyrite-pyrrhotite-pentlandite-gold mineralization in a narrow zone, up to 25 cm. wide, which parallelsthe nearby western (hanging) wall of the dyke. Subsequently a set of conjugate shears formed in the dyke as a result of tectonic movements. Gold-quartz veins formed in these shears giving rise to the classical "ladder veins" of the Morning Star mine. On either side of the veins ("floors") the diorite has been bleached for up to 3 ft. This involved introduction of much CO. and some K"O, and S with abstraction of SiO. and FeO, giving rise to carbonates, sericite, zoisite and pyrite. The veins consist of quartz with minor amounts of albite and carbonate, together with pyrite, arsenopyrite, pyrrhotite, chalcopyrite, sphalerite, tetrahedrite, galena, bournonite, boulangerite and gold. Spectrographic analyses of gold show that the suite of trace elements is consistent throughout the mine.INTRODUCTIONThe gold-quartz veins of the Morning Star Gold Mine, at Wood's Point, Victoria, are a classic example of the "ladder vein" type of deposit. The structure of this series of repeating quartz veins or "floors", some barren and some productive, occurring in a set of conjugate shears which transect a "dyke bulge" of diorite (Fig. 1), has been described on numerous occasions as mining has progressed and figures in the textbooks (Whitelaw, 1905; 1916; Junner, 1920; Lindgren, 1933; McKinstry, 1935; 1942; 1949; Kenny, 1949; Hills, 1952; Clappison, 1953) ; but there has been no study of the mineralization apart from that in Junner's (1920) general study of the Walhalla-Wood's Point Goldfield, made at a time when mining had not developed below the 400 ft. level,. and the mine was dormant.

Jan 1, 1958

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

By G Gilchrist, S C. Dominy, T Jashashvili, R C. A Minnitt

The grouping and segregation error is one of Gy’s seven errors that cannot be measured in any qualitative manner because of its transient and changing characteristics each time the sample is handled mechanically. Attempts to calculate the mean and variance of the segregation error is considered by some as ‘an exercise in futility’ that would not help us achieve representative sampling. This research is aimed at understanding the process of segregation of dense, finely divided and dilute particulate materials supported in a clean quartz substrate during intense agitation. Several mixtures of fine-grained materials including steel, tungsten carbide and gold grains were used in these experiments. Four hundred grains of each of the minerals and metals at a top size of 2 mm were mixed with approximately 600 g of finely ground quartz material (95 per cent passing 2000 microns) in a 500 ml plastic jar with a sealable lid. The mineral–?metal mixtures were analysed in three steps using microfocus X-ray computed tomography. Step one consisted of rolling the containers on a flat surface in an attempt to concentrate the mineral and metal grains in the core of the supporting substrate; this is a base case that can be reconstructed after each session of analysis. The second step involved gentle and vigorous shaking of the mixtures in order to segregate the denser minerals and metals from the supporting quartz substrate. In some cases, a third step involved splitting the sample through a riffle splitter. Three-?dimensional images of the surface of each grain, its volume and its X-, Y- and Z-coordinates, before and after intense agitation of the container, were interpreted from the reconstruction of the tomographic X-ray data. The spatial analysis of grains using cell declustering and 3D variography provided a useful means of characterising the distribution of the grains in space and the extent to which they had become segregated during the process of agitation. Spatial analysis indicates that in general, grouping and continuity of grains is weakly developed. The modelled nugget effect remains high for most tests, indicating that grains of similar size did not group together strongly. Agitation through rolling provided the best continuity, although not consistently in the long axis of the plastic jar. The nugget effect was consistently highest, and the range of continuity shortest in samples that had been split, indicating that the grouping and continuity were reduced through splitting the sample. Initial results indicate that very little segregation of the minerals and metals occurs in the quartz substrate. This is somewhat counter-intuitive, but suggests that the effects of agitation on mixtures of dense minerals and metals in substrates of lower density do not lead to excessive segregation. Differences in behaviour between dense materials in response to agitation are evident. Grains of different composition and shape did not group and segregate in a predictable manner in response to the agitation methods. Initial results indicate that the degree to which a material groups and segregates relates more to the characteristics of the denser material itself, rather than the agitation method employed.CITATION:Minnitt, R C A, Jashashvili, T, Gilchrist, G and Dominy, S C, 2017. Quantifying segregation of minerals and metals in particulate materials using computed X-ray tomography and variography, in Proceedings Eighth World Conference on Sampling and Blending , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By B Haase, R Saha

Conditional simulation (CS) has been extensively used in metal industry to assess uncertainty of geo metallurgical variables to build robust distributions around grade tonnages across different time horizons. Coal’s entry to nonlinear stochastic modelling is relatively new and this paper summarises the work done at BHP to enable its practical usage from production time frames to Life of Asset planning. CS in coal using Sequential Gaussian Simulation (SGS) is used to understand resource confidence around specific variables within pre-defined boundaries of spatially continuous domains for each coal seam. The variation between simulations for a given parameter reflects uncertainty. This paper demonstrates the use of CS to profile resource based upon agreed seam/parameter uncertainty thresholds which affect planning, forecasting, extraction and inform identification of key production risks and defining mitigation strategies. The end goal is to de-risk long-term plans by optimising infill data collection and improve stability in short-term planning through increased understanding of confidences locally rather than at global resource definition stages. The paper also briefly discusses the use of automated workflows and systems to minimise the time spent on the process to enable use in decision-making.

Mar 22, 2022

Large deposits present computational challenges to todayÆs commercial orebody modelling systems that are based on conventional block models. We describe a system that is specifically engineered to model and visualise large deposits. Central to the system is linear octree encoding of conventional block models and real-time conversion of three-dimensional (3D) meshes to linear octrees. We provide both methodological treatment and practical experience in implementing such a system. A commercial implementation is also presented to demonstrate the validity of the approach.

Sep 26, 2011

The overwhelming weight of scientific opinion indicates that human activity is having a discernible and negative influence on the earthÆs climate system. The Australian Government, together with about 100 other nations, has accepted the findings of the Intergovernmental Panel on Climate Change third assessment report, released in 2001. This report was prepared by several hundred eminent scientists from all over the world, from various scientific disciplines and with differing opinions on global warming. The IPCC third assessment report contains a series of relevant, significant conclusions; for example, it finds that there is an increasing body of observations that gives a collective picture of a warming world and other changes in the climate system. Global average surface temperature increased over the past 100 years by about 0.6¦C. This may not seem much, but in the 900 years beforehand, the EarthÆs temperature remained relatively stable. The 20th century was the warmest of the past 1000 years in the northern hemisphere (there is much better information available from the northern hemisphere than the southern hemisphere). The 1990s were the warmest decade of the millennium in the northern hemisphere and 1998 was the warmest year. Although many factors influenced the EarthÆs climate, scientists are confident that greenhouse gas increases were the main factor contributing to global warming in the last 50 years of the 20th century. Increases in carbon dioxide, methane, troposhperic (lower atmosphere) ozone, halocarbons and nitrous oxide have all contributed to global warming. Combating climate change cannot be done without the cooperation of industry and the community at large. It is important that Government and industry work together to achieve greenhouse gas abatement while ensuring continued economic growth. The cause of the problem û the generation of greenhouse gas emissions û lies at the heart of the structure and size of modern economic activity. Greenhouse gas emissions are embedded in our way of life from our energy consumption patterns to the basic production of food. Moreover, the costs of the impacts of climate change to the earth will be potentially revolutionary, not merely evolutionary. It is in this light, acknowledging both the seriousness and nature of the problem before us that I want to reflect on the key drivers in the international climate change negotiations. A consideration of the past, present and future from what I see as the mid-way point in the process. In 1997, Parties agreed to adopt the Kyoto Protocol, which sets out mandatory targets for greenhouse gas emissions for developed countries.

Jan 1, 2002