Search Documents

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Giblett, K Afewu

This paper uses a case study to demonstrate best practices techniques for predicting the contribution of gravity concentration in a gold recovery process flowsheet. The case study was selected as an example of an ore with a marginal gravity gold content, which makes the value of a gravity circuit difficult to quantify. In this instance the value of leveraging a significant knowledgebase of operating gravity circuit performance to support the decision making process was demonstrated. This case study analysis serves as a useful demonstration of best practice methodologies supporting decisions to include or exclude gravity recovery in a gold recovery process flowsheet.CITATION:Giblett, A and Afewu, K, 2015. Do we need a gravity circuit or not? A case study in applying best practice, in Proceedings MetPlant 2015, pp 288–295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By X L. Liu, W Huang, J M. Zhu, S L. Wu

The shape, position and thickness of the cohesive zone have a great influence on the operational performance of the blast furnace. Many researchers have found that the high temperature properties of iron ores determine the formation of the cohesive zone. The results of this work show that sinter of high basicity interacts with lump ores and acid pellets due to the difference in chemical compositions. The softening and melting properties and the primary slag formation behaviours in the cohesive zone are improved by the high temperature interactions. The high temperature interaction is mainly influenced by the chemical compositions, porosity, interfaces and so on. Although the softening and melting properties and primary slag formation behaviours of lump ore A (a typical limonite lump ore from Australia) is the poorest of the iron ores studied, the high temperature properties of integrated burden A (consisting of sinter and lump ore A) is no worse than the other integrated burdens due to the high interaction between the sinter and lump ore A. It is useful to apply the results in the optimisation of blast furnace burden.CITATION:Liu, X L, Wu, S L, Huang, W and Zhu, J M, 2015. High temperature interactivity of iron ores in the cohesive zone of the blast furnace, in Proceedings Iron Ore 2015, pp 363–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D M. Brady

Underground coal mines in Australia have embraced the use of various inertisation techniques both proactively and reactively. The use of such techniques can have a significant influence on ratios and trends used to monitor the status of the underground environment. Whilst control strategies should never be ignored in favour of preserving the integrity of ratios, the influence and significance of the changes likely to be seen should be anticipated and understood for reliable interpretation of the situation. This paper looks at the influence inertisation techniques can have on results and subsequent interpretation.CITATION:Brady, D M, 2013. The influence of inertisation techniques on gas interpretation, in Proceedings The Australian Mine Ventilation Conference , pp 259-264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Melkumyan, F Ramos

This paper addresses the problem of prediction of grade variables over volumes (block estimation) for an autonomous mine. Resource estimation is usually concerned with the prediction of the quality of material over volumes (blocks in resource models). This problem is tackled by developing Bayesian block estimation with the Gaussian processes (GPs) framework. GPs are commonly used for nonparametric regression and classification and offer an elegant solution to deal with incomplete knowledge and information. A GP is defined by its mean and covariance function. The parameters of the covariance function can be learnt by maximising the marginal likelihood of the data. This offers a way of automating the covariance fitting process, while at the same time allowing for an assessment of how well the covariance function fits the data. Within the GP framework the calculation of the average grade over a volume can be performed using Bayesian quadrature, which treats an integral as a random variable. First, it is demonstrated that the block kriging equations in geostatistics are the same as Bayesian quadrature. Then, it is determined when closed form analytical solutions for the integrals are possible and quadrature approaches for approximations are briefly discussed.

Sep 26, 2011

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

By W J. Botha

The Palaeoproterozoic Transvaal Supergroup in the northern Cape Province of South Africa hosts high grade (>60 per cent Fe) hematitic and specularitic iron and manganese mineralisation. The mineralisation is primarily exposed along the western margin or in the central part of a major interference fold structure known as the Maremane dome. The bulk of South AfricaÆs iron ore production is currently provided by two active mines, Kumba Resources megaton Sishen iron ore mine on the northern end of the dome, and the smaller Assmang Beeshoek mine on the southern closure. The undeveloped Sishen South deposit, which contains ~400 Mt of high-grade hematite ore, is located approximately 9 km towards the southwest of Postmasburg. It forms a linear extension of the Beeshoek mine and as such contains comparable laminated, breccia and conglomeratic iron mineralisation. The Transvaal Supergroup sediments were deposited in two distinct fault-controlled basins on the Archean Kaapvaal craton. Basement rocks in the western Griqualand West basin are formed by a carbonate platform sequence (Campbellrand Subgroup), which is overlain by a thick sequence of banded iron formation of the Asbesheuwels Subgroup. A major unconformity separates these rocks from the red-bed Gamagara Formation, which is correlated with the base of the Olifantshoek Supergroup. Diamictites and lavas of the Postmasburg Group have been thrust over these units from the west. The mineralisation process is related to regional scale supergene iron enrichment of Kuruman banded iron formations along the unconformity. During regional tectonism associated with the Kheis orogeny (2400 - 1700 Ma) the Maremane dome was uplifted, and the basal dolomite units thus exposed to erosion and karstification. The overlying banded iron formations collapsed into karst sinkhole structures where leaching of silica and enrichment of hematite occurred. Although the exact mechanism of the mineralising process remains unclear, karstification preserved components of the original concordant laminated and massive ores. These ores were subsequently eroded and deposited as conglomeratic and gritty ores down-dip of the Maremane dome in alluvial fan systems. A thin veneer of recent calcrete or Tertiary Kalahari clay beds masks the subsurface geology and most of the orebodies, thus ground geophysical gravity surveys proved excellent exploration tools to penetrate the surficial cover. These surveys were used extensively for delineation drilling and to deduce the subsurface geology and structural development of the area. Finally Sishen South orebodies were modelled with ModelVision software in an attempt to obtain an exploration template for the surrounding area.

Jan 1, 2005

The word "optimization", refers to the search of an economic optimum, or, more precisely, to the choice of technical parameters which will define the more profitable mining project, knowing the values of the economic parameters. In fact, there is no direct way to perform this optimization, because the extremely large number of technical factors involved, from the type of working and its selectivity to the characteristics of the mill and its flexibility, makes it impossible to make a comprehensive survey of all possible projects. Beside, it would be meaningless to engage in such a task as the deposits themselves are not really known, but only estimated, with sometimes a high level of imprecision. Not to mention the numerical instability which would affect such a computation! In addition, the "best" project is not necessarily the one which strictly maximizes a given profit formula. There also exist human factors which have to be complied with, when choosing the cutoff grades for instance. Finally, there are other non-numerical factors which interfere with the choice between several projects: the shape of the bottom of a pit of the layout of the access road for instance.

Jan 1, 1986

By J Rutter, E Amini, D La Rosa, N Beaton, M Scott, F Faramarz, L Keeney

Anglo American’s Los Bronces copper mine in Chile has been conducting detailed assessments investigating value adding options for their asset. The mine has conducted several detailed Mine-to- Mill and Grade Engineering studies to investigate increased throughput and head grade and to quantifying the impact of these approaches across the life of mine. CRC ORE has two key technologies namely Grade Engineering and the Integrated Extraction Simulator. These two technology suites have been combined to understand the technological landscape and associated value drivers suitable for application at Los Bronces. Detailed ore characterisation test work was conducted to:  measure and spatially model the propensity of ores to naturally deport and  develop customised blast models for Mine-to-Mill and Grade Engineering evaluation The outputs of this work were utilised to develop a block model populated with a range on new Grade Engineering and blasting parameters suitable for scenario analysis. To facilitate scenario analysis a high-fidelity value chain model of the Los Bronces operation from blasting to concentrate production was built in IES. IES was combined with sophisticated analytical tools such as Neural Networks to develop and reconcile a fully integrated value chain. The value chain model made it possible to simulate in IES all available blocks in the block model to predict throughput and grade changes for different strategic scenarios. The scenario analysis was run across 24 strategic combinations of Mine-to-Mill and Grade Engineering and comprised several million simulations. The scenarios investigated each technology independently and jointly to provide an attributed block model that can feed forward into technoeconomic modelling to determine optimal execution strategies for the mine. This paper presents the first published study combining Grade Engineering and IES to provide mass simulation capability to investigate strategic options for a mining asset.

Nov 10, 2020

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

By G Deans, M Longbottom

OZ Minerals’ Carrapateena mine is one of Australia’s newest ‘greenfield’ mining deposits. It will be a 4.25 Mtpa sub level cave underground operation, with an estimated mine life of 20 years. The integration of stakeholder values to inform project development influenced the social and environmental outcomes. A Native Title Mining agreement was developed in 12 months. Project primary approval was obtained 12 months from submission, with achievable licence conditions and one public comment. The project moved from a Pre-feasibility Study in 2016 to construction in 2018. Following recent international dam failures, the Tailings Storage Facility (TSF) was a focus for Government approvals and stakeholder engagement. Significant effort was made into understanding the science around potential effects, impacts and risks. A leading practice Impact Assessment Framework that identified Sources, Pathways and Receptors was applied. A process of failure mode identification and layers of protection analysis was undertaken for robust design controls at each stage, while simultaneously transitioning between downstream and upstream discharge arrangements. Participatory selection of the TSF site and design layout was critical in managing project costs and environmental constraints, and in incorporating cultural heritage constraints and technical risks.

Jul 1, 2021

By A Galley, M Plouffe, T Hynes

Canadian mining research has recently been reinvigorated through a pan-Canadian research strategy driven by the industry, the research community and government departments. These organisations have come together to form the Canada Mining Innovation Council, whose role is to focus and increase mining research in the country. One of the major themes of the organisation is environment; including major research initiatives on energy, tailings and environmental stewardship. Other major initiatives on exploration, mineral extraction and mineral processing will also consider environmental benefits in the research projects they undertake. All the initiatives have their priorities determined principally by the mining and exploration companies, whose first obligation is to determine the long-term research priorities of the industry as a whole, rather than for their individual companies. Only after industry consensus on priorities does the research community become engaged in the implementation of specific projects to address those identified priorities. A goal of the program is to effectively create a virtual mining research laboratory, by engaging all the major research centres in the country. Membership to date includes most of the major mining companies operating in Canada and almost all of the mining-related universities. Other members include federal, provincial and territorial governments, consulting and service companies and manufacturers.CITATION:Hynes, T, Plouffe, M and Galley, A, 2012. A new approach to mining research in Canada, in Proceedings Life-of-Mine 2012 , pp 333-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

By D Jordan, R Wilmoth, J LeFever

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the US Environmental Protection AgencyÆs, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open Pit Highwalls Demonstration Project. This project is funded by the US Environmental Protection Agency (EPA) and jointly administered by the EPA and the US Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome US, located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 m and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied in situ treatment technologies included: a modified, furfuryl alcohol resin sealant, utilising wood and agricultural by-products to coat the rock surface; EcobondTM ARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface; and two AMD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: ASTM D 5744-96, accelerated weathering of solid materials using a modified humidity cells; mine wall residual wall rinse sampling; microscopy; and core drilling followed by water injection testing. The following paper describes the technologies used for passivation of acid generation from the highwall, the field demonstration, and the testing results from the background and each technology plot.

Jan 1, 2003

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

Claiming the Green Revolution - Protecting Investment in Green Mineral Processing

Sep 13, 2010

Courses in chemical engineering and metallurgical engineering at the University of Queensland were compared and the main difference was found to be the greater emphasis on the application of chemical engineering fundamentals, particularly chemical thermodynamics, to specific processes in the metallurgy course. This reflects the distinctive features of extractive metallurgical processes which are not common in other chemical engineering processes and which justify the study of extractive metallurgy in its own right. B.Sc. courses in metallurgy provide one way in which the specialist knowledge of extractive metallurgy can be taught. General metallurgy courses are considered to be preferable to those restricted solely to extractive metallurgy since graduates of a general course have a wider choice of employment, while excessive emphasis on extractive metallurgical applications in chemical engineering courses could reduce the non-specific nature of these courses. Postgraduate diploma and higher degree programmes are avenues for non- metallurgists to acquire knowledge of the discipline.

Jan 1, 1984

By T Y. Ko, Y S. Kang, S J. Park, J H. Hwang

The lunar subsurface, particularly the lava tubes formed by ancient volcanic activity, presents a promising environment for establishing safe and sustainable human habitats on the Moon. Tunnel Boring Machines (TBMs), widely used for excavating tunnels on Earth, offer a potential solution for developing these subsurface spaces. However, the unique lunar conditions, including extreme temperatures, high vacuum, radiation, and the extraordinary strength and abrasiveness of lunar rocks, necessitate significant adaptations to existing TBM technology. This study investigates the feasibility of utilising TBMs for lunar subsurface exploration and base construction, addressing the challenges posed by the harsh lunar environment. We review previous conceptual designs for lunar TBMs, highlighting their strengths and limitations in addressing these challenges. Additionally, we explore innovative excavation methods, such as microwave-assisted rock weakening and undercutting techniques, to enhance the efficiency and effectiveness of lunar TBM operations. By evaluating the geological characteristics of the lunar crust and analysing the potential of lava tubes as launching points for TBM operations, this study provides a comprehensive assessment of the technical requirements and operational considerations for lunar TBM implementation. The findings of this research contribute to the growing body of knowledge on lunar base development and pave the way for future human exploration and utilisation of the Moon’s subsurface resources.

Sep 1, 2024

By A Dunne, R Kruger, H Coleman, P G. Laurens

External and internal challenges in mining are increasing the difficulty and complexity of operating mines. The external mining environment has a big impact on mining operations and is driving the focus on safety, sustainable mining, green issues, profitability and productivity. There is a very high emphasis on ‘reducing cost to improve’, lower mining and beneficiation costs by eliminating waste/inefficiencies (reduce people, use less consumables, multiskilling, etc). The internal mining environment is getting tougher to operate in, with the deposits being more difficult to mine, more difficult to manage due to external pressure along with issues associated with maintaining quality, etc.Technological and environmental developments too numerous to mention, mean that cost control models, reduction in human resource numbers, as well as other drastic measures to curtail expenditure and increase profitability have become part of everyday business. The capability to manage the mining environment in a systemic manner has been lacking and this increases the pressure for performance on those individuals operating and managing mines.Working smarter has become crucial to ensure that businesses optimise the use of their resources, become more safety conscious, more productive and remain cost-effective, while recognising the importance of sustainable mining now and in the future. The logic of determining and managing to the capability of the mining value chain will be examined and the underlying assumptions or beliefs guiding behaviour and decision-making will be highlighted.In order to identify the obstacles in the mining value chain that hinder achievement of its full potential, the following questions have to be asked:What are the factors that influence the performance of a mining value chain?What is the design capacity of the mine?How can the inherent flow and value capacity of a mine be determined?What types of solutions will allow a mine to operate at its inherent flow and value capacity?This article will discuss the way we plan, measure, assess and manage the mine value chain, by addressing the following factors:balanced capacity versus flow and value capacity designthe use of averagingoptimising individual components in a value chain versus optimising the whole value chain.Optimising flow and value through the mining value chain is one of the three pillars of Mineral Resource Throughput Management (MR™). MR™ is an entrenched and academically supported philosophy that has been successfully applied in the past decade in various mines throughout the world by EXXPLEO, a mining and beneficiation consulting company. EXXPLEO has partnered with HCL (a global IT company) to embed the MR™ philosophy, methodology and toolsets into a formal software product called Synchronised Digital Mining (SDM). The SDM system will provide mining companies with a sustainable platform to effectively apply the MR™ principles and toolsets effectively across all operations targeting increased productivity, efficiency and profitability without having to train operations and management staff into expert MR™ practitioners to successfully achieve the desired results.CITATION:Dunne, A, Laurens, P G, Kruger, R and Coleman, H, 2015. Optimising flow in the mining value chain, in Proceedings Iron Ore 2015, pp 437–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018