Search Documents

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R Shelton

The Big Wainihinihi River and tunnel are located on the western side of the Southern Alps of New Zealand within the active Alpine Fault zone, which marks the boundary between the Pacific and Australian Tectonic Plates. The tunnel was built over 100 years ago to supply water for gold mining, but it now conveys water from a high-energy intake to a canal that supplies three of TrustPower’s hydro-electric power stations with a combined installed generating capacity of 10 MW. Part of the tunnel passes through an unstable 50° schist slope, which fi rst suffered a wedge failure in the 1929 Arthur’s Pass Earthquake and was reinstated in the mid-1970s for hydro generation. In 2008, TrustPower’s monitoring system showed that the wedge failure had remobilised and that urgent remediation was required.Harker Underground Construction (Harker) was awarded a design-build contract to restore the tunnel to service by tunnelling a new central section. Their geotechnical engineers, Peters and Cheung, reviewed the tunnel’s stability and proposed a new, safer tunnel alignment, deep behind the failure wedges. This work was based on their failure model, cost-benefit studies, and engineering geology completion mapping at the time of re-opening.Construction innovation was an important factor in ensuring the project’s success, as were detailed geological and geotechnical information, a robust methodology, strong client relationship and planning. To suit the varying rock conditions and restricted space, Harker combined a traditional drill-and-blast method with light-weight modular steel sets and timber supports to reduce construction costs and mitigate support risk. To make material handing easier in the tight conditions, a special electric locomotive was designed and built and blasting confi gurations were adapted to suit varying rock conditions in the highly fractured schist.The isolated site meant interesting and unexpected challenges, particularly communications and resources (both human and material). Despite that, the project was completed within budget, on schedule, and with no lost-time injuries.

Mar 8, 2011

By V O’Brien

The suitability of magnetic surveys flown at low altitudes to identify buried heavy mineral (HM) strands has long been accepted. This is despite the low intensity magnetic response often obtained from such strands. The fundamentals of the magnetic survey method dictate that the closer the instrument is to the source the stronger the response. As such the optimal elevation for the magnetometer is at or near the surface. Iluka sought to use a ground based magnetometer to aid in the exploration target generation process and allow accurate targeting of exploration drill holes. Following the initial trial Iluka recognised the potential additional application of data obtained by a ground based magnetometer over known strand deposits. The detail of the ground magnetic images can confirm the assumed strand continuity between cross-sections of close spaced drilling and can aid in the definition of the geometry of different generations of mineralisation. The ability to confidently determine that the deposit has not been truncated by post emplacement erosion of the mineralised deposit may enable reductions in drilling requirements as well as assisting mine planning activities. Iluka intends to investigate advanced modelling of the magnetic data to determine the level of strand geometry and HM content resolution that can be achieved from the ground magnetic survey data and its potential application in the mining grade control process.It is anticipated that the surveying of Iluka’s known resource deposits will provide the ability to correlate the magnetic response from new exploration targets with those from known deposits for a given depth, HM grade and mineralogy suite.

Oct 5, 2011

By W P. Darcey

Jabiru Metals completed a feasibility study on the Jaguar Base Metal Project in July 2005. The study was based on conventional truck haulage via a decline. Conveyor haulage was considered but not in sufficient detail to provide a meaningful comparison. The current study investigates the cost and productivity of alternative ore transport systems for the Jaguar project. The options considered are conventional underground truck, conveyor, road train, rigid frame truck, monorail haulage and shaft hoisting. Shaft hoisting was not considered in detail due to the high capital outlay for such a relatively short mine life of less than six years. This study goes beyond the common approach of evaluating haulage systems in isolation; it includes development costs, timing of ore production and costs associated with mine services as well as administration and milling costs. The results of this study indicate that the best haulage option for the Jaguar project is conventional truck using the Hitachi AH400 trucks. The net present value (NPV) for this option is A$8.13 million higher than the next best option namely the Kiruna E635 electric truck. The conveyor option has the lowest operating cost per tonne of ore but the longer development time negatively impacts on its NPV. The monorail option is considered impractical due to the number and length of trains required to achieve production targets.

Mar 21, 2011

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By Zajber A, Kulchen R, Letzel D, Weyer A, Schwellenbach J

The search for modem casting plant concepts today focuses more and more on the harmonisation and optimisation of overall concept lines to obtain a continuous quality control and reduce the cost of production (Figure 1). Fin I As far as continuous casting plant concepts are concerned, this specifically requires an optimal adaptation and flexible operation when converting liquid steel into a directly processable product without any in-between treatment. Continuous casters need to fully satisfy the requirements of both the upstream steelmaking facilities as well as the downstream rolling facilities.

Jan 1, 1999

Study on the Interaction Mechanism of Flotation Reagents and Rare-Earths-Bearing Phosphate Ore

Sep 13, 2010

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

By Y Akiti, J Moller, E Esper, R Rugolo, A Pains

"Morro do Ouro Mine is a high tonnage/low-grade mine located in Paracatu, Minas Gerais State, Brazil. The mines move around 55 Mt of ore per year at an average grade of 0.4 g/t. The auriferous mineralisation of Morro do Ouro is related to hydrothermal fluids rich in arsenic (As), gold (Au), lead (Pb) and zinc (Zn). These percolated along favourable structures contained within phyllites of Upper Proterozoic age and defined a mineralised megaboudin which outcropped with 4 km extension and up to 2 km in width. The litologies in the interior of this structure are typically more deformed, sericitised and sulfidised, and exhibit the development of quartz boudins in the centre of the more deformed zones where are found the higher Au grades and the coarser sulfide crystals. Gold is preferentially associated with arsenopyrite, mainly occurring in fractures or aggregations of crystals and is rarely in solid solution or refractory. Over 90 per cent of the gold contained in the sulfide ore is free or extractable by cyanidisation. The current mineral reserve is 17.9 Mt at 0.403 g/t published at the end of 2012.In order to get a good grade estimation that represents the orebody more accurately a solids methodology was used to distinguish the different orebodies. Before 2011 the orebodies were worked with two domains relating to the weathered mantle. The B1 ore, which is oxidised, is located at the top of mineralisation, and is used to feed Plant 1. Underneath B2 ore, which is fresh sulfide bearing, represents over 30 years of production in Plant 2.In order to improve the predictability of gold grade estimation in geological modelling and to get a better predicting behaviour of each domain on the deposit, studies were carried out in which it was possible to show a correlation between elements and the mineralisation. One strong correlation and spatial distribution between Au and As, As and sulfur (S), Au and Pb, Au and Zn were found.Based on geochemistry, mineral correlations, amount of sulfide, structural deformation, texture of sulfides and the daily experience of the mine, it was possible to create solids that individualised bodies with similar mineralogical and chemical characteristics using the parameters listed above.After 2011, a new modelling concept was proposed and built with 11 different domains, compared with the previous, and with two more parameters: recovery acid neutralised capacity (ANC).Each of these bodies have different behaviours in mineral processing, like flotation and metallurgy. For example, bodies with pyrrhotite bring problems in the flotation, bodies with high arsenic do not recover well, bodies with high As with coarse texture have good recovery, bodies with fine texture do not have good adherence in production.In the present state of knowledge, protocols are being developed for bench testing to predict the recovery of each geochemical domain aiming to include these in the geological model for the parameter recovery. It is intended to create a field throughput in the model of ounces per hour, from each block of each domain to better predict the production, using the parameter recovery, Au and Bond Work Index (BWI).CITATION:Esper, E, Rugolo, R, Moller, J, Akiti, Y and Pains, A, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 67-74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By L van Latum, A Koh, I Thomas

Haul truck drivers are at a high risk of developing fatigue due to the monotonous nature of the work and demanding shift rosters. In the mining industry, fatigue is identified as a major contributing factor in several fatal accidents a year. A number of fatigue detection devices are now available, that can contribute to improved fatigue risk management in the mining industry. This paper describes the technology and algorithms behind one particular product which is both predictive and un-obtrusive to the operator. The Advisory System for Tired Drivers (ASTiD), was developed by Fatigue Management International (FMI) in collaboration with the Loughborough Sleep Research Centre (LSRC), both in the United Kingdom. While this system includes a model of the human circadian rhythm as a bias for predicting expected fatigue risk by time of day, it also uses yaw data generated by a solid-state gyroscope in the horizontal plane. Algorithms analyse this data to determine the level of monotony of actual driving conditions and to detect changes in steering control caused by driver fatigue. During normal levels of attention, a haul truck driver applies continuous, small adjustments to the steering wheel. As the level of fatigue increases, steering adjustments become less frequent and more erratic. Differentiating between these modes of control in the highly variable mining environment is accomplished by chromatic processing of the gyroscope data. This paper will go into some detail explaining the principles behind chromatic processing and the specific application of these in detecting fatigue in haul truck operators.Technology in itself is not the solution to addressing operator fatigue, but it plays an important role in ongoing monitoring and maintaining awareness with mining personnel. Furthermore, the specific principles behind ASTiD technology support a risk-based approach to fatigue management, allowing optimisation of the mining operation for productivity as well as safety.

Sep 26, 2011

By C B. Smith, G L. Boxer, S W. Moss, A L. Jaques, V Lorenz, M J. Rayner

The Ernest Henry Iron Oxide Copper Gold deposit is hosted in a large dilation between two moderately dipping shear zones found in the footwall and hanging wall of the deposit. These shears are controlled by a large diorite intrusion to the north-east and south-west of the deposit, formed ~1660 Ma. A shear zone dubbed the ‘Interlens’ uncovered through underground workings truncates the main orebody into two lenses, and is hypothesized to have formed in conjunction with the Hanging Wall Shear Zone and Footwall Shear Zone. All three shears dip moderately to the SSE (50–140) from open cut exposures through to the current mining horizon approximately 800 m below the surface. Routine geological work and a capital drilling campaign has identified a significant flexure in these sub parallel ore bounding shears with increasing depth. A shift in shear orientation in the Interlens over approximately 100 m vertically from ~50° to the SSE to a steep, easterly trend (~85° to the east) is observed in both drill core and exposures in the underground workings. It is hypothesized the diorite intrusive to the south-west of the deposit controls the shear zone geometries at depth. The geometry of the Interlens mirrors the surface expression of the Proterozoic package of the orebounding shears to the south-west of the deposit, suggesting the surface geometries of the shear zones are consistent with depth. Additional drilling to explore the validity of this hypothesis is planned for the near future to better understand the structural controls on the Ernest Henry mineralisation with increasing depth.

Mar 22, 2022

By D P. Sainsbury, J Western, B L. Sainsbury, V Mutton, P E. Petrie

Remnant rib pillars at Castlemaine Goldfields Ltd’s Ballarat Gold Project have been sterilised by the placement of loose rock fill in production stopes. The application of selectively injecting low-viscosity grout into the backfilled stopes to form a stabilised material has enabled recovery of the previously sterilised pillars. This paper outlines the engineering design, quality control and quality assurance program implemented to ensure the safe and efficient recovery of the rib pillars. The successful program included laboratory testing, numerical exposure stability modelling and in situ monitoring.CITATION:Sainsbury, B L, Sainsbury, D P, Western, J, Petrie, P E and Mutton, V, 2014. Pillar recovery adjacent to stabilised rock fill at the Ballarat Gold Project, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 77–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Traditionally, capital costs of major resource development projects have been estimated as a single amount to which a percentage accuracy has been assigned based on the method of preparation of the estimate, that is, on the amount of information available to develop the estimate.However, there is a growing recognition of the importance of a probabilistic approach to capital cost estimates, and of a more rigorous calculation of estimate accuracies and of the presentation thereof. Accuracies can be expressed with more certainty as a percentage of the estimate amount where the percentage represents one standard distribution on the probability curve for the capital cost of that specific project. Thus confidence levels can be stated for various estimated amounts - for example, it can be stated that there is an 85% chance that a stated amount will not be exceeded, or a 90% certainty that a (higher) amount will not be exceeded. Moreover, the right skewness of the probability distribution curve for most projects can be readily recognised and reflected in the evaluations. This enables senior executives and board members to have a clearer understanding of investment uncertainties, and the possible magnitude of commitments.

Jan 1, 1990

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S P. Young, K R. Monro

Reducing metal prices have forced mining operations to become more efficient and innovate in order to do more with the existing base. Much of this effort has focused on improving the efficiency of load and haul operations. The key to this is to understand and quantify where delays and missed opportunities exist. Metrics such as utilisation of availability, efficiency utilisation and asset availability are helpful indicators of performance; however, uptime-based time usage models and performance analysis tools using productive operating time models help to identify additional improvement opportunities.Phu Kham is a copper-gold mine operated in the Lao People’s Democratic Republic (Laos) since 2008 by PanAust Limited. The mine is a single large open pit of 450 m depth, running a fleet of 51 100 t class rigid dump trucks and 300 t and 200 t shovels controlled with the aid of a fleet management system in order to achieve ex-pit material movements of 56 Mt/a.Commencing in late 2014, a range of initiatives were implemented in order to improve the efficiency of the mine haulage fleet. These include hot seating of all operator changeouts via changeout ramps, split shifting of crews to minimise queuing delays, maximising blast volumes and minimising blast event days to reduce blast exclusion delay events including opportune refuelling of equipment during blasting events, inspections of trucks during refuelling events, implementation of a dedicated haul road services team to help reduce wet weather related delays and infrastructure development for haul path efficiency improvements.These and other initiatives have allowed the mine haulage fleet utilisation of availability (UofA) to be sustainably increased from 85 per cent to 97 per cent (see Figure 1), efficiency utilisation to increase from 85 per cent to 90 per cent, and productive operating time (POT) to increase from 73 per cent to 84 per cent. The corresponding increases in efficiency of the haulage fleet has allowed an equivalent reduction of eight haul trucks from the fleet to meet continuing life-of-mine production requirements.CITATION:Monro, K R and Young, S P, 2016. Truck haulage improvements at the Phu Kham mine – the journey to 97 per cent utilisation of availability, in Proceedings International Mine Management Conference, pp 339-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By C S. Kelsey, J R. Kelly

Australia is presently enjoying the fruits of a booming iron ore market. Expectations are that market strength will be supported in the short to medium term by increasing feedstock demands from steel mills, as world economies rebuild post-Covid-19. However, as cost and environmental pressures increase the longer-term market outlook will be dominated by product quality. The ‘flight to quality’ will place increasing demands on direct shipping ore miners as they compete to maintain their standing in the iron ore marketplace. China will progressively disengage from its dependence on Australian imports, leaving miners under increasing pressure to boost product quality and diversify outlets globally. Australia has vast deposits of low-grade magnetite ores located mainly in remote and arid regions of the continent. This paper proposes a dry grinding and magnetic separation process to produce premium concentrate grades from the low-grade ores, to assist in meeting future product quality demands. The premium grade concentrates could be either blended with lower quality direct shipping ores or marketed separately. The proposed dry concentration process involves the pairing of Vertical Roller Milling (VRM), a mature technology widely used in the cement industry, and Planar Magnetic Separation (PMS), a new methodology, which has been developed to the threshold of commercialisation by the private Australian company Cyclomag P/L. Two laboratory prototype planar magnetic separators with field strengths of 1800 gauss and 6000 gauss have been built and tested on a range of magnetite ore types over the past three years. In each case, following grinding to liberation sizes, a combination of roughing and cleaning operations has produced pellet grade concentrates. Vertical roller milling has competed successfully with conventional media milling in grinding cement clinker, limestone and blast furnace slags. A key advantage of dry VRM/PMS processing is its potential adaptability to stepwise modular development, which can minimise initial capital investment, while generating early revenue streams to cope with unpredictable market volatility.

Nov 8, 2021

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By Z Li, Z Yan, T Htet, S Zhang

During the pyrometallurgical processes, a substantial quantity of high-temperature ironmaking and steelmaking slags, generated at temperatures ranging from 1400 to 1600°C, is wasted, as the heat contained in these slags is released into the environment during the tapping process without effective utilisation. On the other hand, a significant amount of energy is required to reheat the cold materials for the manufacturing of glass and mineral-wool, often necessitating the addition of high-silica materials to facilitate the production process. In this study, an innovative approach is presented to harness the heat present in molten metallurgical slags to directly produce new raw materials for glass and mineral-wool manufacturing while simultaneously reducing energy consumption and mitigating CO2 emissions. The theoretical amount of waste glass that can be effectively added in the process has been estimated via thermodynamic calculation. Experimental assessments were conducted to examine the impact of high-silica waste materials on the dissolution, melting and fluidity. Potential recipes for glass and mineral-wool manufacturing were suggested and an assessment of the energy savings, and reduction in CO2 emissions with manufacturing of glass and mineral-wool using this innovative approach were included. It was determined that the processes could lead to a reduction of over 26 kg of CO2 emissions per 100 kg of new material used, primarily due to the utilisation of heat from slag and the accelerated smelting process.

Aug 21, 2024

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011