Search Documents

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

By R Knight

The spatial variability of geometallurgical characteristics in a mineral deposit can have significant impact on financial and mine planning, mineral processing, concentrate quality and tailings composition throughout the life of a project. These characteristics that may determine the success of a project are not readily apparent to geologists unless they are integrated with deposit geology and assay data, modelled in 3D and incorporated into resource block models.One of the primary objectives of geometallurgy is to integrate and incorporate various geologic, geotechnical and geometallurgical parameters into resource block models, which typically are limited to in situ tonnes and grade of economic metals. Critical attributes, such as concentration of deleterious elements that affect the project viability need to be identified and integrated into the resource block model early in the exploration stage to predict project profitability and address potential environmental impacts.Using data from a volcanogenic massive sulfide deposit we present an example of the integration of ore geochemistry (cadmium, arsenic and antimony) with the results of preliminary, bench-scale metallurgical test work in a 3D geometallurgical model that predicts subdomains of poor-quality concentrate and tailings containing environmentally-sensitive elements. This critical information was incorporated into the existing resource block model in order to inform both financial modelling and mine planning.This example demonstrates that geometallurgical data can be effectively integrated with geological and assay data using Leapfrog MiningTM software (Leapfrog Mining) early in the exploration stage of a project. Three-dimensional representations of geometallurgical data can be created directly using primary additive data, as well as from proxies of non-additive parameters. Resource block models can be updated continually with new information as the project passes from exploration through production. In addition, the software allows for 3D visualisation of the characteristics of the materials that will eventually constitute the mill concentrate, tailings, and waste. This study emphasises the critical importance of establishing a systematic geometallurgical approach early in the exploration stage that can be continuously updated with new information throughout the life of the project. In the example that we present, sulfide ore that had otherwise been identified as high-value (in the absence of geochemical and metallurgical data) turns out to be low-value ore due to concentrate penalties and increased environmental impact.

Sep 5, 2011

By Black PM, Itaya T

Arc-type volcanic activity has been a major feature of the late Cenozoic geological evolution of the Pacific-Australian plate boundary in the northern New Zealand region. The timelspace distribution patterns of arc-type rocks reflect changes in the nature of the plate boundary as it has evolved. Inception of volcanism began in the north during earliest Miocene times (26 Ma) following ophiolite emplacement and during the next 10 Ma developed into a volcanic arc segment extending south to the present position of the central North Island. The northern part of the arc became extinct about 15 Ma ago, but activity continued in the central (Coromandel) part of the arc until about 5 Ma ago. In late Pliocene and Quaternary times volcanic activity has become concentrated in a northeast trending zone which is collinear with the Tonga-Kermadec Arc.

Jan 1, 1995

By K White, C Ferguson, M Harding

Understanding watercourses and river processes at a landscape scale is vital for managing risk to mining infrastructure and operations as well as minimising future environmental impacts beyond the life of the mine. Recognising this, Iluka Resources Limited engaged Alluvium Consulting Australia to identify and characterise watercourses across several neighbouring mineral tenements in the Eucla Basin, South Australia (Alluvium, 2013, 2014a, 2014b). The objective of the studies was to inform planning for risk management during mine planning and operation and appropriate landscape rehabilitation for mine closure.Mining operations in the area are by open cut extraction of mineral sands. The extracted resource is processed on-site before leaving the site for export. Several pits are to be developed in stages with simultaneous backfilling and surface reinstatement. Mining is initially taking place in the Jacinth tenement, where up to 100 km of watercourses may be directly or indirectly impacted (refer to Figure 1).The total study area (shown in Figure 1) is approximately 330 km2 and spans three smaller areas that were the focus of separate investigations during mine planning.CITATION:Ferguson, C, White, K, Harding, M and Hardie, R, 2016. Landscape-scale assessment of watercourses in remote arid South Australia to inform mine planning to mine closure, in Proceedings Life-of-Mine 2016 Conference, pp 200–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Permeability and fluid pathways in fracture-controlled hydrothermal systems are governed by a dynamic competition between permeability-creation processes and permeability-destruction processes. Permeability evolution is coupled with the evolution of fluid pressure and stress states. Key permeability-creation processes are micro-scale to macroscopic fracture growth, and the generation of damage zones during co-seismic slip on faults or aseismic creep on faults and shear zones. The competing permeability-destruction processes include crack-healing and sealing, compaction and pore cementation. High rates of permeability destruction in hydrothermal systems require ongoing permeability enhancement to sustain high fluid fluxes and ore genesis.   In aseismic regimes, competition between permeability-creation processes and permeability-destruction processes can lead to continuous flow in deep level hydrothermal systems. However, in seismogenic regimes, rapid co-seismic permeability-enhancement is followed by progressive permeability-destruction in the intervening interseismic periods, and leads to episodic flow. The results of high pressure experiments are used to illustrate how pore fluid factors and stress states are dynamically coupled with permeability evolution in hydrothermal regimes. Particularly in the seismogenic mid- to upper crust, large changes in permeability during the seismic cycle govern relative rates of change of fluid pressure around active faults and shear zones. Rapid, post-seismic recovery of pore fluid pressures, relative to rates of shear stress recovery, leads to growth of hydrofracture networks prior to successive fault rupture events.   Pre-rupture hydrofracture networks do not develop where post-rupture fluid pressure recovery is modest relative shear stress recovery. At elevated temperatures, low rates of pore fluid pressure recovery relative to shear stress recovery promote ductile shear failure and grain-scale permeability enhancement within shear zones prior to rupture events.   The influence of pore fluid pressure cycling, shear stress cycling, and deformation processes in controlling the evolution of permeability, flow localisation, and flow anisotropy at the deposit scale are illustrated for mesothermal and epithermal lode gold systems.

Jan 1, 2005

By Ryan CG, Ramsden AR, Sie SH, French DH, Griffin WL

Proton microprobe and electron microprobe analysis are being used in combination for in situ determination of the trace element contents of oxide, sulphide and silicate minerals in a sample of the Merensky Reef. Initial results indicate that chromites contain only Ni, Zn, Ga, Zr ar d Nb. Platinum-group elements, if present, are at concentrations less than 2 to 6ppm. Ru, Rh and Pd are the only platinum group elements to be consistently detected in the sulphides. PentLindite is the most important host for these elements with the concentration of these elements being dependant upon the mineral association in which it occurs

Jan 1, 1989

By R Valenta

Most developing projects face a range of technical and non-technical challenges, and examination of development histories can potentially provide insights into improved approaches to project development. The Kestanelik project in the Canakkale region of Western Turkey was acquired by Chesser Resources Ltd in 2008. Turkey is a significant and growing source of gold production, with sector participation by both domestic and international companies. While the broad ranges of challenges faced by developing projects is well known, there are relatively few case studies in which the range of technical, environmental, social and governance challenges are presented in a single contribution. Recent studies of undeveloped complex orebodies have particularly shown the extent to which environment, social and governance (ESG) complexities contribute to project delays and failures. The Kestanelik project faced a full range of technical and ESG complexities, and provides an illustrative example of the associated challenges. CITATION: Valenta, R, 2018. A case study of technical, social and environmental challenges for a gold project development in Western Turkey, in Proceedings Complex Orebodies Conference 2018, pp 73–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Before any accident prevention and total safety programme can succeed, a safety concientiousness or attitude needs to be implanted in the employees' minds. Psycholog- ical and physiological conditions play a vital role in accident causation and prevention. Both need attention in a good safety programme, but working place conditions and environment are more easily corrected. However, the challenge is to change attitudes in the minds of men - psychological factors in accidents. To do this does not require a Safety Officer, but does require a Safety Adviser. At Blackwater mine a Safety Adviser is available to all sections of the organisation to guide and assist, to provide data and material to use at meetings, to help in accident investi- gations and to help organise training. To eventually achieve total commitment requires every member of the management team to be a salesman towards all around selling an attitude to safe working, a way of life. At Blackwater mine the workforce is young overall with most employees being under 40 years old. Psychologically this is a quite different problem to a balanced ages working group. A great deal of effort is needed to communicate with the younger, articulate, better educated employee who is also generally a skilled operator in the capital intensive

Jan 1, 1975

An increase in the silver to gold ratio with increase in depth in the main ore shoot of the Crown-Crescent lode in the Emperor gold mine, Fiji, was found to be due mainly to vertical zoning of gold-silver tellurides. The zoning resulted from a two-stage sequence of ore mineralization.The application of some recent studies of the synthetic Au-Ag-Te system to natural gold-silver telluride assemblages is discussed.

Jan 1, 1971

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

By A Yáñez, P Vallejos, R Grau, J Yianatos

In flotation cells, especially in large flotation units, froth management is a crucial variable that should be considered during the design phase or optimised to improve the performance of existing flotation circuits. This paper presents a simulation evaluation of the effect of launder design on the metallurgical performance of an industrial flotation circuit consisting of five TankCell® e630 (630 m3 ) cells in a Cu rougher duty. This analysis was carried out using a new industrial simulator, which was built on a wide database collected from many industrial concentrators. This tool is currently incorporated into HSC Chemistry® software and allows evaluation of the effect of launder design on mineral froth recovery, water recovery, entrainment, and other variables to be quantified. The industrial flotation circuit was evaluated under different launder design scenarios, considering an actual flotation circuit that includes TankCell® e630 cells for calibration and as a reference (baseline). Firstly, two different designs were evaluated in the full circuit: a standard launder design and a new launder technology. It was found that the new launder technology enabled improvement of the mineral recovery along the circuit, mainly for coarse particles, due to the improvement in froth mineral recovery. Next, the partial upgrade of the launder design along the circuit was analysed. Thus, the new launder technology was evaluated in the first and the last two cells of the bank. The results showed that upgrading the launders in different cells along the circuit delivered an increase in the final recovery with respect to the baseline, with a partial impact on the concentrate grade. However, these changes are less than those when evaluating the full upgrade scenario. A partial launder upgrade either in the first or last two cells of the bank showed similar final recoveries, but the latter enabled a slightly higher concentrate grade (about 1 per cent higher) to be achieved. Finally, the evaluation of launder design using the industrial simulator made it possible to estimate its effect on variables that are not commonly obtained from plant surveys, including froth recovery per particle size, collection recovery per particle size and liberation, gangue entrainment and bubble loading grade.

Aug 24, 2022

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Kukla G. T

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland - Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground sub-section of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes Operational.

Jan 1, 1980

By Y Peng, D J. Bradshaw, X Chen

At NewcrestÆs Telfer gold mine, a strategy of regrinding pyrite rougher flotation concentrates has been proposed to increase gold recovery and reduce cyanide consumption in the CIL circuit. The regrinding will be followed by an additional copper/gold flotation stage, where copper minerals need to be separated from pyrite. However, although the minerals are well liberated, the separation of chalcopyrite from pyrite in the cleaner stage is not always straightforward. The surfaces of the fine particles, produced during regrinding, are more easily oxidised and contaminated than coarse particles, directly influencing the particle floatability. The depression of pyrite is difficult in the cleaner stage as well due to copper activation, a process which is also highly dependent on the grinding environment. In this study, different grinding media, including mild steel and stainless steel, was used in the regrinding to produce different regrinding chemistry, such as, pH, Eh, and iron hydroxide contamination. The effects of regrinding conditions on chalcopyrite flotation and its separation from pyrite were studied. It was found that the stainless steel grinding media, which produced an oxidising environment, was more beneficial for the separation of chalcopyrite from pyrite after regrinding. The mild steel grinding media had a detrimental effect on both chalcopyrite and pyrite flotation. This study addresses the importance of choosing suitable regrinding conditions in the pyrite and copper flotation circuit.CITATION:Chen, X, Peng, Y and Bradshaw, D J, 2012. Effect of regrinding conditions on the flotation of chalcopyrite and its separation from pyrite in the cleaner stage, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By T Baumgartl, D Bradshaw, B Forsyth, M Edraki

In a tailings storage facility, the chemistry of pore water is a function of oxidation and dissolution of sulfide minerals, containing metals and metalloids, the neutralising effect of gangue minerals and the geochemical processes controlling solute equilibria such as pH, redox potential, precipitation, ion exchange and adsorption. On the other hand, the changes in geochemical composition of tailings feed over time is a function of spatial variability within the orebody and modifications in processing method. Tailings properties such as pyrite content, pH, concentration of deleterious elements, surface chemistry, pore water chemistry and particle size are already shaped in the dynamic environment of a process plant.To engineer desired environmental outcomes, a new research framework is needed. The new approach should follow the physical and geochemical processes of tailings feed and construct models that can be used for the prediction of seepage water quality and dust propagation and evaluate the potential re-processing of tailings or production of tailings with desirable surface chemistry, particle size and internal structure. The challenge of developing tailings engineering model is not in laboratory techniques, but more of the overall communication of results and establishing the link between disciplines. It requires investigating geochemistry across mining and processing for improved environmental outcomes at tailings storage facilities.The paper reviews the current tailings management practices by comparing the geochemistry and mineralogy of tailings and the chemistry of seepage water from three Australian case studies in the context of geology, mineral processing and climate. Some alternative methods of tailings management are also reviewed and it is concluded that a proactive multi-disciplinary approach is needed with respect to tailings management, based on a novel integrated research framework.CITATION:Edraki, M, Forsyth, B, Baumgartl, T and Bradshaw, D, 2012. Geochemistry of tailings and seepage from three tailings storage facilities in Australia - Uncapped, capped and active tailings, in Proceedings Life-of-Mine 2012 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Many volcanoes in western Melanesia have tectonic settings and rock compositions that do not conform to conventional models of arc- trench systems. Part of the reason for this may be that in an environment of rapid tectonic change mantle source regions bear the imprint of former subduction even though subduction has now ceased. Results bearing on this concept and on other important aspects of Plelit nesian v ican ism and tectonics, were obtained in 1982-1986 from >e,:eral marine - geoscience studies in the re,,ii n

Jan 1, 1987

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

By J Austin, R Bitencourt

Differences between the long-term model (LTM) and mine geology system (MGS) grade control block-outs on a blast block scale can impose difficulties to planning crusher feed grade and tonnes on a monthly to weekly blend basis. Detailed geological input to short-term planning has been integral to improve the performance and reduce risk in six-week to three-month production schedules and local variability in tonnage and grades is often not accurately represented in the LTM. The challenge of producing to combined target specifications from different mine sites in an integrated mine to ship business has been reduced with the creation of blast blockout-based short-term model. These short-term blast block models (STBBM or STM) are robust predictive tools created for upcoming benches of current mining areas by firstly collecting data from the pit in the form of bench and face mapping and projecting the structure and stratigraphy down to the next bench. A wire-frame of the projected contacts based on material destination from production blockouts is created and then checked against the LTM. Blast block data from the bench above including assay results and material logging is extracted and validated according to the projected wire-frames (geozones). Individual blast blocks and a full block model are created for each bench production defined by the STP (bench plans). Data output from the STM is in a compatible format for import into scheduling specific software packages. Additional information is incorporated into the STM to allow querying of drill penetration rates, predicted powder factors, material hardness and feed type to further aid in the production planning process and cost forecasting. To date, reconciliation of the STM has been pleasing and certainly an improvement on the LTM, especially in areas where variability is higher due to geological complexity. Short-term predictions derived from in-pit geological observations allow mine planners to more confidently decide on mining block sizes and schedule tonnages and grades, reducing the risk component attached to developing production schedules based directly upon long-term orebody models and mine plans.

Jan 1, 2005