Search Documents

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

Differences in the assay results of replicate samples engender doubts on the reliability of ore sampling and of assaying procedures. An analysis of variance is a technique to estimate the variability at each level of the procedures. In an example, the variability of one-metre core samples was far greater than that of the assaying technique.

Jan 1, 1976

By G B. Siddall

The paper examines the current state of equipment and circuit design, with reference to Australian practice. Following a review of the changes in milling applications over the last 15 years, developments in mill design are examined. Current issues include trunnion versus shell support; drive type and economic analysis for comparison of the various systems; the efficiency of the mill discharge system for slurry and pebble removal, and lining configuration. Peripheral problem areas such as pebble crushing and classification are briefly examined. Circuit design issues are reviewed. The decision to modify the traditional primary crushed feed is examined with reference to recent and proposed installations. A retrospective look at fully autogenous installations and their successes is presented, and current views on increasing throughput are assessed. Finally, future developments are anticipated in mill design and control, and competing processes are identified.

Jan 1, 2002

By Lightfoot BW, Bultitude-Paull J

The Sirosmelt top submerged lancing system has many applications in the smelting of base metal and complex materials. It has particular advantages for smaller scale smelting and the treatment of recycle materials in smelters where its low capital and operating costs and its operational flexibility are of immediate benefit. The system can be fueled by oil, gas or coal, as well as by mixtures of fuels. For many applications, the use of coal as a fuel has operating cost advantages over oil and gas, but conventional pulverised coal feeding systems entail very large capital expenditure and this militates against the use of coal. The methods available for improving on conventional technology for coal firing of Sirosmelt systems are discussed and operating experience with alternative systems are outlined. The use of coal as a reductant in the Sirosmelt system is also discussed.

Jan 1, 1987

By J L. Merritt

Contour banks and waterways are standard soil conservation measures to assist farmers reduce the impact of gully erosion on sloping cropping land by reducing the slope length to the interval between the banks. The Universal Soil Loss Equation (USLE) developed by the USA Department of Agriculture Soil Conservation Service in 1930s predicts the long-term average annual soil loss (A).The equation is the product of the rainfall erosivity factor (R), the soil erodibility factor (K), the topographic factors of slope length and angle (L and S) and the cropping management factors (C and P). Contour banks reduce the slope length (L) only.Contour banks are a constructed earth embankment, incorporating a channel on the upslope side, typically traversing a slope on or close to the contour to control and/or prevent the erosion of that slope. The banks are also referred to as graded banks, terraces, or bunds (DSITI 2015). Contour banks are either broad based or narrow based. Broad based banks allow the passage of the machinery over the banks whilst narrow based bank batters are too steep preventing the passage of machinery. Waterways are a stable, longitudinally sloping water disposal area of sufficient capacity used to discharge surplus runoff from the contour bank and to allow it to flow to a lower level without causing erosion (DSITI 2015).The mining industry must decide what the role for contour banks and waterways is in each operation’s rehabilitation and closure plan.CITATION:Merritt, J L, 2018. Contour banks in spoil rehabilitation – a matter of timing, in Proceedings Life-of-Mine 2018, pp 147–149 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The implementation of robust, reliable and accurate sampling systems is the key to the successful management of any mineral processing plant. The representative sampling of a mineral processing plant is the only way to determine what is coming into the plant, what is going out as fi nal product and what is going to tails. In plants with high gravity gold components, where high recovery effort gravity circuits are installed, the use of a gravity recoverable gold (GRG) sampling system can assist in the online monitoring of the performance of the circuit. The typical installation location would be in CIP or fl otation feed (ie cyclone overfl ow), downstream of the gravity circuit. A GRG sampling system generally consists of the following equipment: true proportional, continuous drive, linear cross cut sampler, secondary vezin sampler operated on a timer, a batch centrifugal concentrator, and sample dewatering module. The operating philosophy of the GRG sampling system is that the primary sampler operates on a continuous basis, generating a constant stream of truly representative sample. Consep's H&S drive system is unique in its ability to be able to operate in a continuous mode, therefore enabling a continuous stream of representative sample to be generated. The primary sample stream reports to the secondary sampler. The secondary sampler operates on an intermittent basis (nominally ten minute interval), resulting in a relatively small sample volume per shift. Normally the sample volume would be ten to 15 L per shift. The secondary sample rejects stream reports back to the batch centrifugal concentrator. The sample generated from the secondary sampler can be dewatered using a Consep H&S dewatering module. This device produces a final sample that consists of separate filter cake and filtrate. These are suitable for taking directly to the laboratory. The continuous stream of truly representative secondary sampler rejects is passed through an appropriately sized Knelson Concentrator, typically a KCMD7, KCCD10 or KCCD12 sized unit. This unit recovers any available GRG from the stream. The Knelson Concentrator is also purged of its gravity concentrate at the end of the shift. This sample, which is nominally around 1 - 2.5 kg of concentrate, is also taken to the laboratory. At the end of the shift the client will have a measure of the gravity recoverable gold content of the target slurry stream, as well as a true representative sample of the complete stream. Through the addition of a Knelson Concentrator to an otherwise typical sample station, it is possible to generate a true measure of the performance of your gravity circuit. This will take the guess work out of the daily variation in gravity circuit gold recovery, as the site knows whether the changes are due to gravity circuit equipment performance, or due to the natural variation of ore GRG contents. Maintenance planning can also be designed around the system, as the site will have a composite sample to measure the performance of the circuit, therefore indicating where performance has dropped and maintenance is needed. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By E R. Ramanaidou

Two unknown iron ore samples were found by a geologist from Ok Tedi Mining Limited copper, gold and silver mine at an old wharf site dedicated to a 1970s drilling program in Lake Murray in Papua New Guinea (PNG). These iron ore samples could not come from a PNG mine and it was decided that a study should be undertaken to understand their origin. Lake Murray is the largest lake in PNG with a total surface area of 647 km2. It has a high-water 2038 km long convoluted shoreline with seasonal water level changes (Osborne, Kyle and Abramski, 1987) and it is located around 200 km south of the Ok Tedi mine (5°13’25”S, 141°09’37”E). The petrology, mineralogy and chemistry of two Fe samples (Ok Tedi 1 and Ok Tedi 2) included optical microscopy, X-ray fluorescence (XRF) analysis and a comparison with worldwide iron ore deposits. The two rock samples were cut to produce two subsamples: (1) a polished thin section; and (2) a pulp that was used for XRF analysis including major, minor and trace elements. Ok Tedi 1 and Ok Tedi 2 were petrologically and chemically compared to a range of known iron ore samples from Australia, Brazil and South Africa. The petrological study of Ok Tedi 1 indicates that it is composed of granoblastic recrystallised hematite and the overall texture is uniform without any obvious original ‘sedimentary’ texture. Ok Tedi 2 is a ‘specular’ or platy hematite with recrystallised and fused grains. Using both petrological and chemical clues, the two Ok Tedi samples likely originated from the Iron Quadrangle in Brazil.

Sep 18, 2023

By Hoberg H, Schneider FU

Flotation tests were conducted with galena, quartz and with synthetic mixtures of the two, in different ranges of grain size, and with different process parameter variants. Physico-chemical analyses were also carried out on surface energy and on xanthate adsorption on galena with different grain sizes. Reference will also be made to hydrodynamics, interfacial chemistry and the influence exerted by grain size in flotation.

Jan 1, 1993

By A R. Butcher

Gold deportment and ore characterisation studies are key tools in gaining an appropriate understanding of complex gold ores for process development and optimisation. These studies have historically involved imprecise chemical methods with slow and costly optical microscopy for gold identification. The traditional approach requires highly skilled petrographers, is prone to human error, and is not scalable, reducing the usefulness in practical analysis. The proposed methodology utilises a decision tree and knowledge base in a staged approach to gold ore characterisation, building up progressively more detailed information about the sample mineralogy, gold deportment and key mineral properties, as the process is followed. Whilst the automated QEMSCAN« system is used for mineral and gold identification, interactive and focused data analyses are used to give more efficient and accurate results. This is complemented by smart sample preparation and chemical methods to enhance and validate the data, making the staged approach methodology reliable, scalable and therefore practical and economical.

Jan 1, 2007

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

By Piotto P

Pit optimisation algorithms are designed to produce a pit with maximum value, but for certain minerals like iron ore, limestone, coal, etc, it is also necessary that the designed pit contains ore which meets the customer's chemical specifications. This paper describes a technique of using linear programming for blending optimisation and the Lerchs-Grossmann algorithm (as in Whittle's 3D software) for pit optimisation in tandem, to achieve pit designs of targeted grade specifications.

Jan 1, 1996

Commencing from a platform acknowledging the capability of the Russian mining industry in open cut and underground mining operations a revitalisation of the industry will depend on an assimilation of mining economics and on an opportunity for technical training of Russian mining industry professionals.Successful foreign investment in parallel with the reconstruction of the industry rests on an understanding of culture, history, internal controls under central planning, and external factors affecting mining development.

Jan 1, 1997

By Slattery T. E

Recent develognents in zinc flotation at the North Broken Hill Limited concentrator are discussed. An outline of the history of zinc flotation and a description of current practice is presented. Installation of on-stream X-ray analysis probes has resulted in inproved metallurgical performance and focussed attention on automatic control. Results are presented of investigations made over the past six years which have led to the formulation of experimental schemes for the automatic control of zinc flotation.

Jan 1, 1983

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

Blasting is known to be both an important and an easily quantified cost factor in rock breaking operations. However, the indirect costs and benefits of the blasting operation are not easily determined due to the irreversibility of the mechanisms involved and the multiplicity of influencing factors. A general conceptual model showing the relationship between blasting and mining costs is well known, but serious attempts to address the critical real relationships have all floundered on the fact that not enough is yet known about either detonation physics or blasting effects. This can only be remedied to the extent that blasting instrumentation enables researchers to pin down not only the relationship between the detonation process and its impact on a particular environment, but also the downhill costs of handling the rock, repairing any damage and building in "Safety Factors" to provide for imponderables. It is vital to standaraize on specifications for instrumentation and measurement techniques and there is a need to review what has been achieved in blasting expertise so as to focus on the most fruitful paths for future work.

Jan 1, 1990

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

Through partnering with mining customers, DYNO has been able to develop some specific technologies that benefit blasting operations particularly in underground mining. Some of these areas are: 1. Cost allocation and product tracking systems; 2. Borehole video surveys of breakthrough blastholes; 3. Borehole video photography for logging VRM blastholes; 4. Toe-load uphole loading for sublevel cave mining operations; 5. 3D blast modelling for underground ring blasting. This paper outlines these developments in the context of a Canadian underground metalliferous mine.

Jan 1, 1995

By Russell P

Polyurethane resin (PUR) is extensively used in almost all coal producing countries. On the local scene, PUR components suitable for underground application were selected and subsequently, trials were carried out at several coal mines. This paper describes the work at Pikes Gully Colliery (B.P.3Coal), where water flow rates of up to 4.5 m (1000 gallons) per minute, were reduced to 1-1.5 m /minute at the tirst stage of application. Subsequent trials were carried out at West Cliff Colliery (Kembla Coal and Coke). A variety of PUR chemical mixtures were tested in coal ribs and in the roof of intersections and roadways. The trial results are presented with all particular details. Using the PUR injection method, the roof, at the most difficult intersection, was stabilised and 'de-bonded' roof bolts were re-sealed. At Pikes Gully and West Cliff Collieries, 2 tonnes and 3 tonnes of PUR chemicals were injected, respectively. The technique, primarily based on German experience (Bergwerksverband), was used by Delta Control Systems Pty. Ltd. ACIRL was closely associated with the trials, which were monitored by installation of the measuring Stations.

Jan 1, 1986

An experienced drill operator is able to make a log of a drill hole defining physical properties of the earth such as hardness or structure as they vary with depth. This log is based on intuition or how the drill æfeelsÆ. Rock characterisation using measure while drilling (MWD) parameters aims at refining this intuition into a package that accurately defines the properties of the subsurface as the drill bit propagates. Subsurface investigation using MWD parameters aims to combine physical drill parameters: Pull down force, rotary speed, penetration rate, torque and vibration in such a way to yield real time rock properties. MWD is investigation in its most primitive form, put simply MWD is merely a physical probe æfeelingÆ what the rock mass is at depth.

Jan 1, 2001