Search Documents

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By P Bethune

Back Creek is a tributary of the Condamine River. It flows in a northerly direction across the existing Commodore coal reserves. The diversion of Back Creek was proposed to minimise sterilisation of the reserves. The approval process required a Waterworks Licence application, under the Water Resources Act 1989 (Qld), for the construction of a stream diversion channel and floodway. The diversion was designed using the æreference reachÆ approach, which mimicked existing properties of Back Creek. The following design standards were developed for the diversion: the diversion corridor width was 500 m; the diversion geometry was specified for both the low-flow channel, and the floodplain; material properties were specified for both the low-flow channel lining and the diversion bund; compaction standards for both the low-flow channel and floodplain were set; and the diversion rehabilitation included a riparian corridor and pasture land with clumps of native trees and shrubs. The following performance criteria were developed for the diversion: velocity regimes were replicated for the design events considered, in an attempt to avoid increasing the diversion flow velocities in comparison with the existing creek flow velocities; sediment transport calculations indicated that no significant change in sediment transport was expected within the diversion; overburden settlement estimates for the spoil placed in the corridor were summarised, and will be monitored throughout the construction process; geotechnical stability of the proposed Eastern Pit Buttress and the diversion bund configurations was confirmed; and groundwater impacts were assessed. Construction techniques, monitoring and further investigations are also discussed in this paper.

Jan 1, 2003

The reduction in man's contribution to the Greenhouse effect will only be achieved by a number of small steps. Some steps will absorb carbon dioxide (CO2) from the atmosphere in slightly greater quantities, others will reduce the amount of carbon dioxide generated. This paper deals with the reduction of carbon dioxide by improving the combustion efficiency of petroleum fuels. Until recently most reductions in fuel consumption and air pollution have been brought about through mechanical adjustments to combustion equipment. Since the development of tetraethyl lead, little has been done to chemically modify combustion reactions to improve fuel efficiency or reduce emissions. During the past five years Australian laboratory and field trials with ferrous picrate treatment have demonstrated significant and economic gains in the combustion efficiency of diesel fuels. These studies have revealed that even under ideal conditions in diesel engines, carbon monoxide (CO) momentarily saturates the combustion chamber. This state reduces combustion rates, peak pressure and power and increases the risk of pollution. Theoretical, laboratory and field data are presented which support the mechanism by which the ferrous catalyst accelerates the oxidation of CO to the terminal CO2 thus reducing fuel consumption and the undesirable combustion products accompanying the CO saturation of combustion environments. While this paper deals principally with diesel fuels commonly used in mining operations, the catalytic effect of the ferrous ion is also shown to significantly reduce fuel consumption by petrol engines thereby promising a means to reduce the much larger contributions to the Greenhouse gases by automobiles.

Jan 1, 1989

This paper is based on studies made intermittently from 1937 to 1950. Its object is to describe the surface geology and the tin lodes, and to relate the lodes to the structure of the field.PREVIOUS REFERENCESR L. Jack made his first report on the field in 1880, but his principal report was made in 1883. W. E. Cameron described the Great Northern lodes in 1904. Numerous later reports on various mines were made by L. C. Ball, J. H. Reid and C. C. Morton, the most important of which were on the Black King, Good Friday, St. Patrick and the Great Northern Gully Shaft.GENERAL GEOLOGYJensen maps the Herberton area as part of a granite massif intruding rocks of two ages, the Younger Metamorphics of Silurian-Devonian age, and the Older Metamorphics of Older Palaeozoic age. The distinction is apparently based on lithological data. The Older Metamorphic rocks occur as inliers in the granite massif to the west and east of Herberton (Fig. 1).The area described consists of granite traversed by numerous dykes. West of the area, approaching the Older Metamorphic rocks, the granite becomes finer grained as if chilled towards its contact, and the dykes more numerous. To the east, passing from the Nova Scotia mine to Mount Lavery there are numerous dyke rocks, but the outcrops are poor and knowledge of the geology indefinite. The area is the main tin-producing area. To the west there are comparatively small tin lodes in the granite, and the "Copper Firing Line" occurs in the Older Metamorphic...

Jan 1, 1951

By Muir DM, Tsuchida N, Dalton R

The adsorption or loading of anions onto extruded based peat activated charcoal has been studied by potential measurements in a flow through cell. Loading rates are in the order F-

Jan 1, 1984

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

By J Kinal, I Mitchell

Many flotation plants use pH to adjust the pulp chemistry of their system to achieve optimum separation. For example, in a sequential lead/zinc circuit the pH during sphalerite flotation is increased to 10.5 or greater to depress galena and pyrite, thereby improving selectivity for sphalerite. However, maintaining a pulp at a particular pH value does not necessarily provide the operator with an abundance of information regarding the chemistry changes occurring within a plant. This paper provides the reader with a number of pulp chemical observations in several plants, showing that the same trends are noted over time; however, the magnitude of the measured values do change. Further, the changes in magnitude are invariably associated with a change in mineralogy. Thus, is measuring pH enough? Can the Eh, dissolved oxygen and temperature be measured at the industrial scale reliably? And, are these measurements useful?

Jan 1, 2006

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

By T Y. Dube

In this paper current net present value (NPV) based mine valuation techniques that take into account market and private risk are discussed and analysed. Potential pitfalls that arise from the application of a portfolio, market or commodity based risk metric to a mining project are identified. An alternative non-simulative framework for quantifying and factoring market and private risk in NPV calculations is proposed and then applied to a hypothetical case study in an attempt to overcome identified pitfalls. Mathematical proof that a static discounted cash flow (DCF) calculation can underestimate or overestimate mine NPV is presented, the conditions for each are outlined and the degree of underestimation defined.CITATION:Dube, T Y, 2012. How the use of market-based risk metrics can undervalue good mining projects and overvalue poor ones, in Proceedings Project Evaluation 2012 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G R. Ballantyne, G Lane

Dry milling circuits that include high pressure grinding rolls (HPGR) or vertical roller mills (VRM) and air classification have replaced dry ball milling in cement production, but how do they compare to wet milling and classification circuits in mineral processing plants? Two case studies are presented that compare the energy efficiency, wear, liberation and capital cost of dry and wet milling circuits. In both case studies the VRM and HPGR consume half the energy of a wet tumbling mill for the same duty. However, the dry classification system tends to significantly erode the energy benefits. A number of improvement opportunities are presented that have the potential to improve the energy and capital efficiency of dry milling circuits. These improvement opportunities focus on the dry classification system that consumes significant energy in heating and fan power requirements and requires a large proportion of the footprint.

Aug 24, 2022

By J P. Richards, M D. Johnston

The Porgera gold mine, located in the highlands of Papua New Guinea, produced 7.7 Moz of gold between 1990 and 1998. Reserves are estimated to be 12 Moz of Au. The deposit is associated with 6 Ma-old mafic alkalic intrusions emplaced at shallow levels into unconsolidated Jurassic and Cretaceous sediments, where they caused the formation of peperites. The mineralisation consists of an earlier base-metal-sulphide-rich stage with sericite-carbonate alteration (stage I), and a later phase represented by quartz-roscoelite veins (stage II). New styles of mineralisation and alteration have been recognised at depth in association with stage I. They consist of the assemblages magnetite-chalcopyrite-pyrrhotite and biotite-actinolite-anhydrite respectively. In addition, the recent recognition of adularia in some stage II veins (with roscoelite) confirms the similarity of this style of mineralisation with other adularia-sericite or low-sulphidation epithermal deposits.

Jan 1, 1999

By E J. Hancock, K H. B Chu

Failures within hard rock underground excavations have historically been defined by a depth of failure, estimated in the field or through individual measurements, with a simplified failure geometry; such as 1/3 span, cubic or paraboloid. This simplified shape, volume and mass of failure is typically used to estimate in situ demand as a simplified discrete point. However, the highly variable failure geometry indicates simplified methods to estimate the mass can be erroneous in comparison to high precision LiDAR scans. Advances in technology have enabled the accurate capture of failure geometry and allow a far more accurate analysis of failures to be completed. This case study investigates a number of real-life failures to accurately define the failure geometry, the distribution of the failure parameters and compares this to traditional methodologies. This paper also outlines a suggested means of standardising failure geometry parameters whilst accounting for their variability.

Nov 29, 2022

Seam gases are the most important atmos- phere contaminants in Australian collieries, their importance increasing with depth; C02 as well as CH4 may be important in intruded envir- onments. The generally high rank of the coal, with low moisture content, makes for abnormal dust production. The other contaminants are introduced and subject to better control, in- cluding products of spontaneous combustion. Due to market situations the generally lower rank and higher sulphur coals more prone to self heating are mined less. Future mining at greater depths should see greater problems with atmosphere contaminants.

Jan 1, 1983

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G Harbort, V Lawson

Mount Isa Mines Limited operates one of the worldÆs largest underground mines in North West Queensland. ItÆs mining and smelting complex produces copper anode, crude lead bullion (containing silver), and zinc concentrate. Copper is recovered in the Copper Concentrator from chalcopyrite ore, converter smelter slag and rotary holding furnace (RHF) slag via grinding and flotation operations. During 2002 a project to optimise cleaner circuit capacity was commenced. Its aims were to minimise copper losses and minimise slag/chalcopyrite cross contamination by reconfiguring existing flotation equipment and the addition of new flotation capacity. To minimise cross contamination a Jameson Cell was installed and dedicated to cleaning of slag concentrates, which had formerly been conducted by three flotation columns operating in series. The flotation columns were re-configured to operate in parallel and dedicated to upgrading chalcopyrite concentrate. In addition a Jameson Cell was installed to reject entrained copper from a prefloat concentrate consisting of talc and carbonaceous pyrite. This paper discusses the logic behind the cleaner circuit expansion, recent test work relating to the Jameson Cell and the installation and commissioning phases. Difficulties relating to the commissioning are reviewed and the solutions to problems are highlighted. The benefits the reconfigured circuit has provided to Mount Isa Mines are also discussed.

Jan 1, 2003

By H G. Poulos

Prediction of ground deformation caused by soft ground tunnelling is an important problem facing design engineers. The ground deformations are caused by the closure of the gap formed around the tunnel due to the tunnelling procedure and soil intrusion via the tunnel face into the tunnel. There are three different approaches that are commonly used in practice to estimate the ground deformations due to tunnelling, namely, empirical methods, analytical methods and finite element methods. One of the important issues of tunnelling in urban areas is the assessment of the likely impact on adjacent pile foundations of ground movements arising from tunnel construction. The main objectives of this paper are two-fold: first, to assess the available methods to estimate the tunnelling-induced ground deformations, and second, to examine the effect of such ground deformations on adjacent piles. Analytical solutions to predict the tunnelling-induced ground deformation developed by the authors are used in this study. These estimated ground deformations are imposed on the pile in simplified boundary element analyses to compute pile responses. The influence of various factors such as tunnel geometry, ground loss ratio, pile diameter and ratio of pile length to tunnel depth are examined in this study.

Jan 1, 1999

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

By A Clarkson

Cannington Mine is an underground silver lead zinc operation located in north-west Queensland which has been in production since 1997. Ore is primarily moved through an underground material handling system comprised of a crusher, conveyor and hoisting shaft. The Fowler Shaft was constructed in 1997 using a strip and line method with the intent for it to provide a means to hoist ore from the loading station 600 m below surface. The shaft also serves as the route of key services including high voltage power, mine dewatering and fresh air. Despite the adherence to a mining exclusion zone, large-scale change in geotechnical conditions around the shaft were first observed in 2015. Ongoing ground movement around the shaft lead to cracking and delamination of the concrete liner. Shaft management required the on-site team to measure deformation rates and magnitudes, forecast change, manage rockfall risk and deforming pipework, and ultimately, hoisting skip clearance. Monitoring techniques to observe and measure deformation were required to evolve with the magnitude of movement. Some techniques leveraged off modern technology while some of the most useful techniques were based on logic and first principles. All shaft deformation management strategies relied on the co-operation and alignment between Cannington’s Infrastructure Maintenance, Survey and Geotechnical Departments.

Mar 29, 2023

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987