Search Documents

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By Walker G. S

Infrared and Raman spectroscopy have been used to study a range of solid state and aqueous solution species which are of interest in extractive metallurgy. In the solid state new Cu(II)/CN'/NH3 complexes have been detected, iron impurities in kaolin characterised, aluminium substitution in hematite and goethite quantified, and the crystallinity and orientation of zircon determined in heterogeneous crystals. In aqueous solution metal cyanide complexes and equilibria were readily characterised, the thermal decomposition of SO2 monitored and products identified, and complexation of AI(III) by hydroxycarboxylates observed. Attempts to monitor the early stages of the gelling of silicate solutions were less successful, with only changes in the gel being detected. However, the degradation of 12-tungstosilicic acid was readily monitored as a function of both time and pH.

Jan 1, 1996

By G B. Ebsworth, J Krokowski de Vickerod

Several drilling programs at Maldon have produced 7790 core samples, which were assayed for gold, with 2825 of the samples assayed for nine other metallic elements. There is a lack of correlation between gold and all other elements. The situation, however, changes dramatically when sorted according to the abundance of arsenic. In the populations where As >200 ppm, there are strong, positive correlations between gold and several elements. There is also a strong positive correlation of Au with the weighted sums and products of all elements with the elemental averages as a weighting factor, and Bi*Sb and Bi*As elemental products. In these populations, there is also a strong positive correlation between the logarithms of Au and logarithms of each element, as well as the elemental sums and products described above. The correlation coefficients increase with higher As cut-off values.All elemental distributions but especially gold show a high-nugget effect and display high skewness and dispersion, low kurtosis, and common outliers. The distributions of their logarithms are several magnitudes less scattered and without outliers. Thus, the logarithmical distribution correlations are best for practical use.Correlation coefficients were T-tested and are statistically significant. The elemental correlations, particularly those of logarithmic values of weighted sums and Bi, could be used as a gold path finding tool at Maldon. After a preliminary assay for gold and arsenic, only samples with As > 200 ppm should be assayed for other elements. Higher values of gold-correlated elements or elemental ratios, in samples with low gold grades, may increase confidence that gold is under reporting due to its highly nuggetty nature.CITATION:Krokowski de Vickerod, J and Ebsworth, G B, 2012. Correlation as a gold path finding tool at Maldon, Victoria, in Proceedings Narrow Vein Mining 2012 , pp 131-144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

The resource industry must prepare for the inevitable shift towards automation as an operational objective. Although this may seem like a distant concern, many mining companies and equipment manufacturers are already conducting full-scale automation trials. The necessary technology is advancing at a rapid pace yet the training of people to support it at the trade level lags far behind. Those given the responsibility of installing and maintaining automated equipment in the mining environment require a unique set of skills and knowledge. These training needs demand attention to ensure that the wider uptake of automation is sustainable and achieves its full potential.   This paper documents work undertaken by CRCMining and the Mining Industry Skills Centre towards establishing a training framework seeking to address the needs of trade level personnel tasked with the support of automation equipment. A comprehensive definition of the skills and knowledge required by the hypothetical automation-specialised tradesperson is presented. The training pathway identified for these personnel is also described. This work forms part of the Mining Industry Skills Centre's Automation Skills Formation Strategy, funded by the Queensland Department of Education and Training.

Jun 1, 2010

By H Jha, M C. Thomas, P Gupta, S K. Sit

The modern jig with a state-of-the-art control system is much more effective than its older version. This improved control system is used to modulate the amplitude and the frequency of the jig cycle. These two prime parameters are optimised with respect to feed characteristics for best jigging performance. Based on this understanding any jigging plant can be optimised. In addition to these established facts present study shows process efficiency improves further through optimisation of the feed quality.

Jan 1, 2007

By D Head

IonicRE acknowledges within our mining industry, there is a common belief that workplace health and safety, often referred to as safety, is just a matter of ‘common sense’ – something obvious and easy. However, at IonicRE, we hold a different perspective. We understand that safety is far from easy. We recognise the need to emphasise the importance of understanding and conveying the inherent difficulties of working safely. We are committed to implementing processes that support individuals in achieving our safety objective of eliminating fatalities and permanently disabling injuries. To build resilience and sustainability into safety performance, we draw parallels with the principles underpinning sustainable and exceptional production performance. Achieving sustainable safety performance demands effective leadership, meticulous planning, adept management, genuine care and unwavering commitment. We’ve leveraged various tools and techniques, such as DISC theory, Maslow’s hierarchy, process control, Kaizen, Six Sigma and Kirkpatrick’s 4 levels, among others, to facilitate this improvement. There methods play a pivotal role in developing a Safety Blueprint for enhanced safety performance. This paper provides an overview of IonicRE’s Safety Blueprint, a strategic framework for developing our safety capability. Our capability is underpinned by three key pillars. Firstly, a comprehensive risk management approach is imperative, encompassing the understanding of hazards, the identification of threats to our people and the associated risks. Secondly, it entails providing and enforcing accountability to sustain our safety capability. Lastly, it involves constructing an effective defence system against threats and harm. Implementing these pillars requires a meticulously devised change process. Anticipating resistance and potential setbacks, we underscore the importance of having the right people and a wellcommunicated vision for safety at IonicRE. A Safety Blueprint serves as a detailed plan outlining the path toward a future goal. At IonicRE, we contend that safety in the mining industry has generally lacked a coherent and effective Safety Blueprint – a comprehensive plan to navigate the journey toward a destination. Drawing parallels with NASA’s detailed plan for landing a man on the moon safely, we question why, as an industry, we cannot similarly eliminate fatalities. While progress has been made in the last century, we must not wait another 50 years to eradicate fatalities from our industry. Examining Safe Work Australia data from 2008 reveals that 47 per cent of mining fatalities result from vehicle activity and 40 per cent stem from individuals being struck by an object. As of December 7, 2023, seven lives have been lost in the mining industry in Australia this year, indicating a stubborn trend mirroring 2022, with limited improvement over the past 25 years. These incidents are not isolated or unexpected. We understand the hazards and controls, yet fatalities persist. IonicRE considers that the mining industry stands at a critical juncture – do we accept a plateau in mining safety performance, or do we rethink our approach? At IonicRE, we are thoroughly reassessing the hazards that threaten our people, systematically redefining effective risk control measures and establishing a robust framework to hold individuals accountable for the effective implementation of the control measure.

Apr 16, 2024

Following the experimental work of Denny, Robson, and Irwin, and the clinical investigation by Crombie and Blaisdell, an investigation of aluminium therapy was begun at Washington, Pa., which is situated In a very large industrial section of the State. Some of the men to be studied were from plants manufacturing silica brick, refractories used in steel and glass manufacturing, and semi-porcelain table-ware; others were workers in foundries, sand blasters, and men engaged in the quarrying of ganister rock.This group of workmen gave an opportunity to study the effects of aluminium on various types of silicosis which differed somewhat from that found in hard-rock miners.EXPOSUREIn their occupations, the men studied were exposed to silica dust concentrations ranging from 17 to 97 per cent free silica. In the silica brick industries, the unfired product averages 96 per cent silica in the form of quartz, whereas the fired brick contains 50 to 62 per cent. cristobalite plus 11 to 80 per cent. tridymite, forms of silica that, on account of their higher solubility, are more toxic than quartz. The operational dust counts in the plants varied from 15 to 9,500 particles per c.c., and the median particle size from the aerial samples was 1.0 micron for the green product and 2.0 microns for the fired product. The length of exposure varied with the occupation as well as with the individual plant, but disabling silicosis could be produced in less than four years in certain exposures. The average time needed to produce radiological silicosis in those susceptible to this disease was eight years. Some of the men in our series of cases have been treated as long as fifteen years after exposure had ceased, and have improved under treatment.The dust counts mentioned above had been reduced prior to the aluminium therapy studies and the presen.t exposures do not exceed '900 particles per c.c., the average being 370 particles. per c.c. This improvement in dust conditions was due to improved dust control apparatus, which was installed before aluminium therapy was instituted. Aluminium powder is not a substitute for dust control.PATHOLOGYThe pathological picture of silicosis in men engaged in the ceramic industry is somewhat different from that in hard rock miners." Due to exposure to high concentrations of dust containing high percentages of silica of varying degrees of solubility andvery small particle size, these men are subject to a relatively rapid type of silicosis, which sets up an acute...

Jan 1, 1945

AustraliaÆs current interest in renewable energy is based on a desire to reduce the countryÆs greenhouse gas emissions. Wood from sustainable sources offers a unique opportunity to combine greenhouse gas benefits with other significant environmental and social benefits, including salinity mitigation, carbon sequestration, soil replenishment and rural industry. The challenge is to make renewable energy from wood in a cost competitive manner, so that this broad range of benefits may be best realised. Bioenergy and carbon products are of great interest as new, commercial forestry products that can drive large-scale environmental tree planting:In Western Australia, Enecon has worked with Western Power Corporation to build the first full-scale plant for integrated processing of mallee eucalypts, to produce activated carbon, renewable power and eucalyptus oil. It is intended that this plant is the first of a number of such plants to help catalyse environmental tree planting in Western Australia. New technologies being developed overseas may provide competitive bioenergy in areas where traditional markets for wood do not exist. For example, pyrolysis converts wood into a bio-oil that may be transported to remote sites for power generation in gas turbines. Pyrolysis also produces wood char. Pyrolysis and wood-to-ethanol technologies, coupled with short rotation coppicing trees, offer the long-term prospect of large-scale production of renewable fuels around the country.

Jan 1, 2006

Computational models are very useful for studying many of the physical mechanisms which can cause sample bias. Within such models we can predict the trajectories of all individual particles and thereby make observations which are not possible for physical systems. Physical mechanisms highlighted include congestion at the cutter aperture, particles bouncing over the cutter aperture, air drag on fine particles, waves of material being bulldozed off the belt by the upstream side of the body of square cutters, and particles being thrown by the leading edges of cross-belt cutter blades. Having identified relevant physical mechanisms for an existing cutter, we can estimate the extent to which they are likely to result in unequal representation of portions of a stream of material and thereby estimate the maximum likely sample bias.

Mar 1, 2010

By B Chi, A Mahanta, R A. M Maddever, O Dominguez

BHP Billiton, in collaboration with Sodern and CSIRO, has developed a downhole logging tool for measuring geochemistry in situ. The FastGradeTM 100 (alternatively, FG100), exploits pulsed fast and thermal neutron analysis (PFTNA) to analyse the rock. This method is based on the detection and measurement of characteristic gamma rays emitted from isotopes in the material that become briefly radioactive when they are bombarded with neutrons. The tool outputs raw spectra arising from three types of neutron interaction, namely, inelastic scattering, neutron capture and neutron activation, which occur in successive time-windows (Smith et al, 2015). The spectra contain peaks at specific energies that are characteristic of the different elements interacting with the neutrons, the gamma count of which is related to elemental concentration. BHP Billiton uses in-house data processing software to convert the measured spectra to elemental concentrations.Much work has been done to understand the tool response under a wide variety of environmental and operating conditions, including logging speed, borehole rugosity, the presence of cavities, water etc. Effort has also been directed at understanding and quantifying the current sources of error in our conventional assays due to sample collection, preparation, and laboratory instrumentation in order to use this information as a baseline to compare against the FastGradeTM 100 results.To date, the FastGradeTM 100 primary use has been as a verification tool (JORC, 2012). However, beyond this, it has considerable potential to improve productivity in both exploration and production environments due to its ability to provide geologists with assay results soon after a hole is drilled.This paper presents initial test work and tool performance, including accuracy and precision under various conditions. Results are illustrated by comparing tool measurements to assays from laboratory samples collected from both reverse circulation and diamond-drilled holes.CITATION:Chi, B, Maddever, R A M, Mahanta, A and Dominguez, O, 2017. Near real-time assay with downhole assay tool (FastGrade™ 100), in Proceedings Eighth World Conference on Sampling and Blending , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Factors of importance in the ntilization of coal fines are mentioned, and the results of flotation tests on coal fines from three important coal seams in New South Wales are presented.INTRODUCTIONEconomic utilization of fine coal is an important problem in the Australian coal industry, particularly as the proportion of fines mined is increasing with progressive mechanization.While the use of uncleaned coal fines may be economic, it may be preferable to beneficiate them, but the most economic process must be selected.For beneficiating coal finer than about 28 mesh, froth flotation can be applied, but mining engineers should avoid practices that may be detrimental to flotation. Such practices include the indiscriminate use of water, particularly that containing a wetting' agent, for dust suppression. In addition, clay stemming in wet conditions may produce slimes which could adsorb on coal surfaces, while the use of oils and greases as well as the application of stone dust and chlorides in roadway consolidation may influence adversely fine coal beneficiation.This paper deals with the application of flotation to samples of fine coal from the Bulli, Greta, and Victoria Tunnel seams. In addition a discussion is given of the mineralogical constitution, size analysis, and degree of liberation of ash constituents of the various samples.COAL SAMPLESRepresentative samples of coal from the Bulli, Greta, and Victoria Tunnel seams were obtained for testing.

Jan 1, 1961

By Madgwick J. C

Powders prepared from the algae Gracilaria secundata, Ulva lactuca and Ecklonia radiatawere shown to provide sole nutritional support for microbial, microaerobic, biodegradation of low-grade manganese dioxide ore. G. secundata was the most effective bacterial nutrient giving 32 per cent recovery of Mn++, at an average rate of 63 mg Mn++/litre/day and a yield of 24 mg Mn++/g dry powder in microaerobic cultures containing 1.5 per cent (w/v)MnOz ore and 3per cent (w/v) powder over 14 days. Although G. secundata was approximately half as effective as molasses in supporting microbial decomposition ofMnOz, possible on-site growth ofthe alga could be economicaIIy more practical than transporting carbohydrate to a distant mine site.

Jan 1, 1987

Increasingly, mineral operations need to manage water as a key business asset. Managing water solely as an environmental issue leaves a business exposed to social, cultural and economic risks associated with water. Adopting a company-wide strategic approach, which takes account of the true value of water will provide businesses with opportunities and risk protection. Rio Tinto has recognised the business imperative for water stewardship and has responded by producing the Rio Tinto Water Strategy. This strategy commits the company to managing water assets in a responsible manner, taking account of environmental, social and economic values. To incorporate the true value of water in site decision making, a new set of tools is required at the operational level. A key part of the strategy focuses on developing a framework to value water based on case study examples from around the Group. This paper presents progress on the companyÆs experiences in developing and implementing the water strategy.

Jan 1, 2006

By Smitham J. B

A selection of Australian washed coal samples was examined to determine the effect of sample hydrophobicity (rank) and particle size on froth stability in the flotation process. The results indicate distinct rank-based variations in froth volume and stability for flotation tests conducted without the use of collector, over a series of particle size distributions.High-rank coals showed a greater tendency to generate stable, high-volume froths than coals of lower rank. Implications for circuit design and operation are outlined.

Jan 1, 1988

Diversification has characterised the mining industry in this country and globally in recent decades, and in Western Australia in particular. One of the most obvious aspects of diversification is technological change which continues at a rapid and sometimes bewildering pace. A function of technological advances is the increased capacity to further diversify the range of minerals which can be identified in economic concentrations and profitably extracted. This broadening of the total base of the industry has a synergistic effect on its further development by extending its geographical spread and increasing scope for decentralised infrastructure. Another aspect of diversification is the corporate thrust towards establishing overseas mining bases for a variety of reasons. Off-shore (sea bed) mining is a further manifestation of increasing diversity, although very much in its infancy.

Jan 1, 1996

By L McCarthy, B W. Cuffley, O K. Thomas an

The Central Victorian Goldfield is a world-class field located in Victoria, Australia. It is currently undergoing a revival through activities in the Bendigo, Ballarat, Tarnagulla, Maldon, Castlemaine and other fields. Sediment-hosted auriferous gold-quartz reefs that are structurally and geometrically complex dominate the region. To date, no remote methods have been developed to assist in the targeting of the discrete high-grade oreshoots that characterise the mineralisation. An understanding of the structural setting and controls, and thus likely frequency of repetition of oreshoots remains the main exploration tool. Gold within the reefs is generally characterised by both its coarse nature (>100 up to 10 000 microns) and erratic distribution; as a result, most of the Victorian deposits are classed as high- to extreme-nugget effect systems. This characteristic ensures that mineralisation is very challenging to explore, evaluate and exploit. The key issues facing the explorer and miner are related to effective sampling, and definition of geological and grade continuity, and ultimately grade and tonnage. Tonnage can often be estimated to a reasonable level of confidence, whereas the grade estimate generally carries a medium- to high-level of uncertainty. In these deposits, surface diamond drilling alone is generally only able to define an Inferred Mineral Resource, with underground development, closely spaced in-fill drilling and bulk sampling/trial mining required to define Ore Reserves. The extraction of gold from ores is relatively simple, based on the coarse nature and hence amenability to gravity recovery. Ground conditions and the need for in-stope grade control (eg mapping, sampling etc), generally point toward mechanised cut-and-fill as the primary stoping method in the region. To potential investors this style of mineralisation has been viewed as high risk, because of the associated low confidence in the grade estimate, general paucity of Ore Reserves at mining start-up and need for underground development at the Feasibility Stage.

Jan 1, 2004

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By Larke R, Warnock J

Although Western Mining Corporation has been producing high grade nickel ore at Kambalda since 1967, it has only recently become a significant gold producer.The main source of Gold ore has been the Victory Gold Mine located 17 kilometres South of Kambalda.This mine produced small tonnages of high grade gold ore from a sediment horizon within a complex sequence of mafic flows, in the 1890's, early 1900's and 1930's.Today, mining is centred around 2 com-pletely different ore bodies named Victory and Defiance, and involves several different mining methods. This paper describes the Operation's history and gives an outline of the proposed stoping methods.

Jan 1, 1984

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002