Search Documents

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

The Wattle Dam gold mine, located near Kambalda in the Goldfi elds region of Western Australia has recently progressed to an underground operation and is now believed to be Australia's highest grade operating gold mine. At end of March 2010, the deposit had reserves of 132 000 t @ 20.8 g/t for 88 000 oz and by the end of June 2010 had produced 110 000 oz from open-pit and underground mining. The Wattle Dam main lode is characterised by very coarse gold mineralisation. Gold occurs as cm to decimetre fracture fi ll veinlets, shear surface coatings and erratic fl akey clusters. The gold has no quartz or silica association and lacks adjacent low-grade mineralisation or alteration assemblage. Geologically it appears atypical of Archaean lode gold deposits and may represent an extreme end member of the type. Definition of the lode is largely dependent on effective geological identification of the host lode zone and an understanding of the erratic distribution and grade behaviour of a high-nugget, coarse gold deposit. Dependence on assay data to defi ne the lode zone would result in the deposit being mined incorrectly and much of the deposit being left unexploited. This paper discusses the geology, coarse gold characteristics and defi nition methods which are used to successfully defi ne and mine the deposit.

Aug 1, 2010

Mining ventures are essentially risky businesses. Explorers and project developers (plus their investors and financiers) attempt to minimise the risks involved or at least manage them. Core considerations are the obvious technical and commercial risks, but the socio-political system and regulatory environment in which the project will operate can be more important. Successful mineral investments in a country depend upon obtaining realistic and reliable technical results in a country that provides certainty, to gain and maintain investor confidence in a project. Brief commentary is provided on the usefulness of professional accreditation and ethics plus other specific reporting codes (eg JORC/VALMIN Codes) in reducing risks by reinforcing high technical competence and reputable individual professional behaviour (particularly in the context of currently perceived high corruption levels in so many countries). These various risk components are reviewed, especially in a global context, to showcase New ZealandÆs current position. Successful projects are those which provide investors with credible and reliable optimal results in less volatile environments because investors/lenders hate uncertainty and surprises even more.

Jan 1, 2005

By S Arnold

Properties of the soil profile fundamentally control water-limited ecosystems. Soil water availability affects vegetation dynamics of plant communities, but is also affected by these communities in return. Understanding this eco-hydrological interplay and the role of physical soil restoration is crucial for successful rehabilitation and management of post-mining landscapes in semi-arid areas. However, uncertainties exist in both the mathematical description of plant communities within ecological submodels and the predictability of future rainfall events. This study uses information gap decision theory combined with an ecohydrological system model to investigate how both uncertainties impact decision-making in the context of ecosystem rehabilitation. A range of management strategies are investigated to identify the optimal soil thickness for successful rehabilitation of native plant communities in Central Queensland. The results emphasise that thicker soils can counterbalance uncertainty in mathematical description of plant communities by increasing the simulated survival probability of plant communities. However, the influence of thicker soils on the robustness of plant communities against a change in future rainfall amount is rather marginal. By allocating an economic value for restoring a particular thickness of soil layer, these results can be used to evaluate the costs of ecosystem re-establishment with regard to two target measures - the survival probability of the plant community and their robustness against climate change.CITATION:Arnold, S, 2012. Finding optimal soil restoration strategies in the face of uncertain future rainfall amount, in Proceedings Life-of-Mine 2012 , pp 91-96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The Energy Authority of NSW has wide powers and responsibilities conferred by its Act which are pertinent to the State's coal industry and its development into the next century. With respect to coal, the broad objective is to maximise the benefits to NSW and its people derived from the State's coal resources. The initial focus of the Authority's coal-related activities in the late 70's and early 80's was on petroleum substitutes from coal. Research was supported, especially on hydrogenation, and the Authority participated in the Joint Australia/Federal Republic of Germany coal-to-oil feasibility study. It also co-ordinated a State Government initiative to involve the private sector in examining the possible establishment of a synthetic fuels industry based on Hunter Valley coal. With a short-fall in world-wide petroleum supply now seen as less likely for some years, the Authority is looking also at ways of working towards the broad objective in the field of coal utilisation on both domestic and export markets. Areas of interest include possibilities for using washery rejects, means of making NSW coal more competitive as an energy source, use of coal-seam gas and new or special technologies for burning coal. The future is expected to see renewed interest in producing petroleum substitutes, and coal - as the State's major energy resource - is seen as a strong contender as a basis for such an industry. Developments in coal-based power generation are also expected to have an impact, with advanced technologies having a possible place here as well as Overseas.

Jan 1, 1987

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

By O J. Restrepo Baena, S Nowosad, R Webber-Youngman, N Mojtabai, P Foster, A Binder, S Hazuria, erson, S Raval, L Liu

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalisation, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that is suited to contemporary and future of the mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more

Sep 1, 2024

By J Mercuri, S Dunford, P Rothman, E Bartsch, J Snyder, D Newton, R Maron, D Cirulis

The purpose of a mineral comminution circuit with a ball mill running in closed-loop with a hydrocyclone classification cluster is to feed the downstream process with the target particle size. Maintaining the optimal particle size in the flotation feed can significantly improve plant cash flow. In particular, reducing the amount of coarse material is often a major challenge. Existing instrumentation to provide particle size measurement is considered standard equipment in most modern concentrator plants. However, availability is often very low, mainly owing to high maintenance requirements of the analyser and associated sampling system.CiDRA Minerals Processing has developed two novel and robust technologies that address this challenge by providing high reliability and very low maintenance systems for on-line measurement of coarse material in the overflow of individual hydrocyclones. The first system is non-invasive and measures pebbles and rocks greater than 6 mm. This paper focuses on the second system, which is a ruggedized wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter, such as percentage above 150 micron.Both systems have simple robust designs and measure in the primary overflow stream of the individual hydrocyclone. Individual hydrocyclone measurement enables identification of poor performing hydrocyclones in addition to providing a representative measurement of the whole hydrocyclone cluster. The systems do not require sampling and associated sample transfer piping circuits that are prone to plugging, thus avoiding high maintenance requirements.The wetted sensor will be described in detail along with its implementation in a robust control scheme in a major copper concentrator in North America. Plant data shows very high availability, achieved with very low maintenance, has enabled improved process control, thereby maintaining throughput and ball mill target power while reducing grind size.CITATION:Cirulis, D, Dunford, S, Snyder, J, Bartsch, E, Rothman, P, Maron, R, Newton, D, O’Keefe, C and Mercuri, J, 2015. Process optimisation using real-time tracking of coarse material in individual cyclone overflow streams, in Proceedings MetPlant 2015, pp 93–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

For the purposes of this discussion it is assumed that contributors should express the thoughts that arise from their personal experience. So wide is the range of mineral deposits, and so varied the methods employed in their discovery and development, that no two geologists are likely to have been impressed with the same applications of their science. The author's own personal experience has been, during recent years at least, very largely concerned with the broader aspects of the employment of scientific method and geological knowledge to the problems of exploration and exploitation, for the guidance of the general public and governmental authority rather than of mine executives and directors. The view-point thus reached is likely to differ in many respects from that of men who are much more intimately concerned with the mining problems of a single metal or a single mining field, and for this reason a statement may perhaps supplement those from others whose experience has been markedly different.It may well happen that, at some not distant date in the future, when systematic and comprehensive instruction in economic geology is embodied in the courses- prescribed for mining engineers during their years of training, the author's comments will be quitesuperfluous; but at the present time they appear to him to call for expression.The Need for Training of Mining Men in Economic Geology.Contact over a period of many years with mining men who have had different kinds of training and experience has been convincing that there is a general reluctance to acquire a full rational understanding of the geological factors involved in exploratory and developmental problems. The correction of this attitude is regarded as vital to the industry and it is necessary to insist that the outstanding requirement of the present day is the utilization of all branches of geological, investigation in the field and the laboratoryby men who have had systematic and specialized training in these matters. The science of geology is many-sided, but is, nevertheless, whole and essentially indivisible. No one can afford to disregard any fraction of its content 'or any of its methods of investigation.The greatest advances have been made in the understarnding of the occurrence of mineral deposits by those whose knowledge Qfbasal principles, has been soundest, whose endeavour has been to ascertain all their relationships in space and time, whose attention to detail of all kinds has been keenest, and at the same time, whose capability to distinguish between major and minor features has been most marked.With the passage of the years and the accumulation of data from many lands, it has been possible to build up a great body of information regarding the primary deposition and secondary alteration of mineral occurrences, which is of the utmost value in guiding thesearch for new deposits to take the place of those that become exhausted. This heritage is due not only to the efforts of gifted in...

Jan 1, 1950

By K J. Riihioja, E Nozawa

SmartTag is a radio frequency identification (RFID) based technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and finally into the concentrator. This paper presents current developments and the future direction of the SmartTagÖ ore tracking system, as well as presenting some case studies. Successful applications of the SmartTag system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This presented Metso with a number of technological challenges, including RFID tag and antenna design. By reducing the traditional RFID tag diameter from 60 mm to 20 mm the RFID tags can now successfully pass through a secondary crusher. The new smaller RFID tags (referred to as mini RFID tags) have been used in some Process Integration and Optimisation projects with very promising results. The results indicate that the miniature RFID tags have a higher survivability to blasting and through secondary crushing stages. Extending ore tracking further through the process allows more reliable linking of spatial data with time based process performance. Metso is looking at developing even smaller micro RFID tags, and is also investigating other applications for the SmartTag system, including ore tracking from the original source to the final destination (ie from the mine, through the plant and ports to the customer).

Sep 26, 2011

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Good morning and thank you for the opportunity to address this yearÆs New Zealand Minerals Conference.   As you have already heard from the Associate Minister of Energy, the Government believes that the minerals industry is an important part of our economy. In particular, our coal and lignite resources have the potential to play an important role in New ZealandÆs energy sector as both a primary fuel and as a means to produce electricity.   The Government has taken a keen interest in the primary fuel sector given the declining reserves of natural gas sector. The energy sector is a key driver of economic growth and it is therefore critical that we have a reliable supply of primary fuel as part of the energy mix.   In a global sense, New Zealand is like many other countries regarding the need to secure energy for the future. Natural gas will be a key bridging fuel in the transition from an energy market based on fossil fuels to one based on renewables over the next century.   However, natural gas as a solution to this energy transition has some pragmatic limitations for New Zealand. There is uncertainty as to when new domestic reserves of gas can be discovered and developed. And the alternative of imported LNG poses a number of costs and risks to the economy.   New ZealandÆs coal resources are vast-estimated to be enough to last hundreds of years at the current rate of extraction. The main question is can extraction be increased and sustained to meet the demand of domestic power producers and at the same time meet commitments to lucrative international markets?   At this point it is appropriate for me to place coal into context with Governments overarching policy objectives for energy. The Government has stated objectives for the energy sector emphasising energy efficiency and an increased focus of renewable energy, while still ensuring security of supply and certainty as to energy costs and risk. Coal certainly can make a contribution to these objectives going forward.

Jan 1, 2005

By M A. Ohsberg, A C. Robertson

Quarrying in Australia accounts for a total annual production of around 200 Mt/a of sand, aggregate and materials used in construction. This material has an annual value of the order of $2 billion and, combined with transport costs of a further $1 billion, the annual value of quarry products are in excess of $3 billion. Currently all of the production of construction materials in Australia is from open cut quarrying or dredging. This paper focuses on the extraction of material by underground mining methods, termed æunderground quarryingÆ. The paper considers a case study for future underground development expansion of the existing open cut Mt Coot-tha quarry, located 5 km from the centre of Brisbane, Queensland.

Jan 1, 1999

By J E. Everett

Ore selection is generally a highly subjective task, with emphasis on producing product with a consistent target grade matching a perceived market requirement. A composite selection criterion ‘Comp’ (a linear function of the grade vector) can be used to maximise ore tonnage at a specified target grade (in Fe and contaminants) extractable from a block model. The blocks correspond to the selective mining units, with grades interpolated from diamond drill hole data. An iterative procedure has been developed to identify the coefficients and cut-off value for the composite function ‘Comp’, maximising potential ore tonnage at target grade.Commonly, target grade is predetermined by marketing; however, there is no guarantee that maximising ore tonnage at a specified target grade maximises the potential value of the mine. If the value of ore could be expressed as a linear function of the grade components, then these coefficients would be appropriate for the selection criterion ‘Comp’. The cut-off value for ‘Comp’ would correspond to the marginal cost of production; all blocks with a ‘Comp’ score above the cut-off would be classified as ore; and the cumulative grade of these ore blocks would be the average product grade over the life of the mine.Unfortunately, no such value function for iron ore is generally available. Methods for estimating the value function are discussed, using the spot price and sensitivities based either upon operational tolerances for Fe and the contaminants or upon published price differentials. This approach has been applied to an anonymous Pilbara deposit with about one million blocks averaging 1.1 kt. It is shown how the optimal target grade, cut-off grade and maximum tonnage can all be explored as a function of marginal cost and iron ore price. Alternatively, given marginal cost and an iron ore price, the effects of changing the tolerances (and therefore the relative costs of the contaminants) can also be explored.It is suggested this procedure can enable informed decision-making for an iron ore mine. Rather than setting final policy for the entire life-of-mine, the method enables target grades and tonnage estimates to be revised by re-computation as the mine life proceeds to recognise changes in market conditions and knowledge about the resource.It should be emphasised that this paper is concerned with ore selection rather than ore sequencing. Appropriate ore selection is a necessary but not sufficient condition for maximising value. Having identified the set of blocks that potentially maximise value, the sequence in which they are mined will present a trade-off between producing at constant grade and extracting high value ore early. The sequencing issue is not considered here. It is shown that optimum ore selection for an open pit mine is independent of any consideration of discount rates, although ore sequencing will depend upon the time value of money if the product grade is to vary across time.CITATION:Everett, J E, 2015. Ore selection to maximise value, in Proceedings Iron Ore 2015, pp 443–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Yindong Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, a O2- , and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of a O2- , which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions. * Originally published in the Proceedings of MINPREX 2000, published by The AusIMM.

Jan 1, 2001

By H Aoki, A Nakayama, K Morita, S Yamada

The thermal conductivity of mold flux is crucial for optimising the productivity and quality of steels. This study investigates the thermal conductivity of molten oxides, including CaO-BO1.5-AlO1.5 (CBA), CaO-BO1.5-AlO1.5-SiO2 (CBAS), and CaO-MgO-BO1.5-AlO1.5 (CMBA) melts, using a hot wire method. Additionally, their structure is examined using Raman spectrometry and magic angle spinning nuclear magnetic resonance (MAS-NMR) to explore their relationship. Furthermore, first-principles calculations are employed to assess the covalency of each bond in the melts for a more quantitative analysis of their relationship. The study confirms that an increase in the CaO concentration of the CaO-BO1.5-AlO1.5 melts reduces the amount of bridging oxygen and consequently decreases thermal conductivity. The covalency of the B[4]-O bond is highest, especially when the second-nearestneighbour Al atoms transition from Al[6] to Al[4], forming the AlB3O7 structure with B[4]. The relationship between thermal conductivity and the structure of CaO-BO1.5-AlO1.5-SiO2 melts can be quantitatively assessed using the degree of polymerisation of the network structure and the variation of covalency as indicators. Furthermore, replacing CaO with MgO in the CaO-MgO-BO1.5-AlO1.5 melts reveals a mixed alkaline earth effect on thermal conductivity.

Aug 21, 2024

By S Strong, L I. Sanz Vivanco, T Brown

One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the prestressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels.An essential part of the tunnel ventilation system, the smoke duct extends the full length of the 4.6 km-long twin two-lane tunnels. The vast majority of the tunnels (approximately 4.3 km) were constructed using two 12.4 m diameter double-shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit-out challenges. A key component of the civil fit-out of the tunnels was constructing the smoke duct in the TBM tunnels, which was designed as a precast solution.The slabs, which each measure 8.62 m long × 2.0 m wide × 200 mm thick and weigh close to 9?t, need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space-proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100 mm.This paper tells the story of how the Transcity Joint Venture (JV) tunnel fit-out team comprising some of Europe and Australia’s leading tunnel construction specialists drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system in solving this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began.CITATION:Brown, T, Strong, S and Sanz Vivanco, L I, 2014. How the global experience and reach of tunnelling’s true multinationals helped solve a road tunnel fit-out challenge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 507–512 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014